Can't join any wifi with my iPhone 5

the error message states it states "incorrect password for wifi". I can get on with ipdad and macbook. password is correct. I set the wifi to WPA/WPA2 Personal

Howdy Benjamin,
Here is a great little article about troubleshooting wifi connections on iOS. Named iOS: Troubleshooting Wi-Fi networks and connections it can be found here http://support.apple.com/kb/ts1398.
These sections in particular:
Occasionally while using your iOS device, you may notice unexpected Wi-Fi behavior, such as:
Difficulty locating or connecting to a network
Unexpected Wi-Fi signal strength or disconnects
Unable to access the Internet
Not automatically connecting to Wi-Fi when expected
Follow these steps to troubleshoot the above issues.
Be sure that you are in range of your Wi-Fi router (access point).
Tap Settings > Wi-Fi and turn Wi-Fi off and then on again.If unable to do so, see this article.
Confirm that your Wi-Fi router and Cable or DSL modem are connected to power, turned on, and indicate that they are connected to the Internet.If not, refer to your network administrator or ISP for assistance.
Restart your iOS device.
Tap Settings > Wi-Fi and locate the Wi-Fi network to which you are connected. Then tap > and Forget this Network. Try to connect to your desired Wi-Fi network again.
Note: You will need to enter your Wi-Fi password again if your desired network requires one.
Turn your Wi-Fi router off and then on again2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
Update your device to the latest version of software.
Update your Wi-Fi router to the latest firmware2.For AirPort Base Stations, see this article for information about firmware updates.
And
Unable to connect to a Wi-Fi network
Verify that you are attempting to connect your desired Wi-Fi network.
Make sure you are entering your Wi-Fi password correctly.Passwords may be case sensitive and may contain numbers or special characters.
Reset network settings by tapping Settings > General > Reset > Reset Network Settings.
Note: This will reset all network settings including: previously connected Wi-Fi networks and passwords, recently used Bluetooth accessories, VPN and APN settings.
Regards,
Sterling

Similar Messages

  • Sudden I can't do any thing with my iPhone, It got died

    Hi,
    All on a sudden I can’t do any thing with my iPhone. It got died, upon plugged in the power to recharge the battery its automatically switch on and start working, i have been facing this issue consistently (from last 1 week i was facing this issue around 3 times). Please look few other details below and provide some solution for this.
    FYI -  1. phone was fully charged when phone was died.
             2. when phone was dead, i tried to press home button and lock button simultaneously 10 to 15 seconds, still it is not responding

    macminded wrote:
    on the about tab, it says 13.7 gb capacity.
    Available: 0 bytes.
    You have "0" available.

  • Can't connect to wifi with my iphone 4...

    Worked great for months, changed to another network and when I got back to my network I changed it in settings and it won't pull up any websites.  Nothing else has changed, thats it.  Wifi is turned on in settings.  I also restored network settings.

    Looks as if it is to do with your iPhone, if it can't find any Wi-Fi networks and they are turned on and set to discoverable, even after restarting the router it's still unable to find it my recommendation is to do a restore through iTunes, the update may not have installed properly, I have an iPhone 4 16GB (Black) running iOS 5.0.1 and it finds my Wi-Fi networks and log's onto them no problem, so clearly the software works, just seems that your iPhone is having a bad time
    You've done everything else I'd reccommend, normal re-boot, soft reset, reset network settings.
    Think it's time to do a full back up in iTunes and do the restore, then see if that resolves the issue, be sure to let us know how it goes if you do decide to do this.

  • I can't connect to wifi with my iPhone 6

    My iPhone 6 will not connect to wifi. I have restarted it, restored network settings. I have shut off the key chain in iCloud.

    Hi bgb07,
    If you have an issue with your iPhone not connecting to any Wi-Fi networks, and you have already tried restarting the phone and restoring your network settings, I would suggest that you back up any data on your iPhone and restore it as a new device. See this article -
    iOS: How to back up your data and set up your device as a new device
    Thanks for using Apple Support Communities.
    Best,
    Brett L 

  • TS1559 I can't connect any WiFi on my iPhone 4s. Switch is grey and "OFF"

    Also, it scans for Bluetooth devices, but never finds any. I did the latest update BECAUSE I was having problems, but that didn't fix it. I reset network settings; still a grey WiFi switch "off". Software restore didn't help.e

    Here's an apple support article specfically for your issue:
    http://support.apple.com/kb/ts1559

  • I can not join any secure wifi network with my iphone5

    I can not join any wifi network that requires a password including my home network. This is very frustrating

    Hi Crystalmais,
    This article contains troubleshooting for connecting to a Wi-Fi network:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    Take care,
    - Ari

  • Hello i have a  an iPhone 5 .i updated it in the end of summer or begin of fall because i forget the number of  version.it is important that i update my i Phone by itself not with iTune . after that my device can not  join to wifi to internet but another

    hello
    i have a  an iPhone 5 .i updated it in the end of summer or begin of fall because i forget the number of  version.it is important that i update my i Phone by itself not with iTune . after that my device can not  join to wifi to internet but another of app works properly and cellular can join to internet . i reset my i phone in the setting . general section but my problem  is remaining .is possible that to return to older version? if there is any solution share with me and i be very thankfulness of you.tanks again 

    It is not possible to downgrade to an earlier version.
    Have you tried the tips on this help page? iOS: Troubleshooting Wi-Fi networks and connections
    And you dont need iTunes to update you're device. You can update it OTA in Settings > General > Software Update

  • Hello i have a  an iPhone 5 .i updated it in the end of summer or begin of fall because i forget the number of  version.it is important that i update my i Phone by itself not with iTune . after that my device can not  join to wifi to inter net but another

    hello
    i have a  an iPhone 5 .i updated it in the end of summer or begin of fall because i forget the number of  version.it is important that i update my i Phone by itself not with iTune . after that my device can not  join to wifi to inter net but another of app works properly and cellular can join to internet . i reset my i phone in the setting . general section but my problem  is remaining . if there is any solution share with me and i be very thankfulness of you.tanks again

    It is not possible to downgrade to an earlier version.
    Have you tried the tips on this help page? iOS: Troubleshooting Wi-Fi networks and connections
    And you dont need iTunes to update you're device. You can update it OTA in Settings > General > Software Update

  • Hi all, i can't sync over wifi between my iPhone 4 and Windows 7 64 bit, wifi sync works with the same phone and my Windows 8 machine, tried solutions from other threads with no luck, just thought i'd see if anyone else had any ideas, thanks.

    Hi all, i can't sync over wifi between my iPhone 4 and Windows 7 64 bit, wifi sync works with the same phone and my Windows 8 machine so the problem seems confined to Windows 7. I've tried solutions from other threads -
    Making sure everything is allowed through firewall
    Rebooting phone/laptop/router
    Disabling ipv6
    Disabling all networks except the one curently on
    Re-installing iTunes
    Restoring iPhone
    No luck with any of those unfortunately so i just thought i'd see if anyone else is still without wifi sync after trying those as well and if you ever found a fix, thanks.

    I just wanted to leave a note that it's working now. I'm not sure if it was the latest iTunes update that got it working or that i decided to start a new library instead of using the one i had backed up on Windows 8 (it didn't occur to me to check using the old library when i re-installed iTunes). But if anyone is having this problem, it might be worth trying again with a new installation of iTunes to see if the latest update works for you, and if not, try using a fresh library instead of a backup (by fresh library i mean discard your old library completely and start a new library, not just restore as new iPhone, a whole new library).

  • After I connect with my iPhone (3GS 5.0.1) to any Ad-hoc wireless Network then walk away out of the reach of my wifi network, my iPhone can't find any wifi Network afterwards, only by turning off the iPhone completely and turning on again.

    After I connect my iPhone (3GS 5.0.1) to any Ad-hoc wireless Network then walk away out of the reach of my wifi network, my iPhone can't find any wifi Network afterwards, only by turning off the iPhone completely and turning on again.
    switching off wifi and on again or going into airplane mode did't help!
    This problem happens only with ad-hoc wifi networks not with normal ones.
    (Ad-Hoc network was created on XP Computer)

    Welcome to Apple Discussions
    Sorry, but the 169.x.x.x IP address is internally generated by the iPod (and iPhone) and indicates that a network has been detected but no IP address has been issued. Your friends iPhone was not connected to your ad hoc network either - it connected to the internet through the 3G network.
    You should read through the Vista help screens on ad hoc networking for some insight how this works. You should be able to get some ideas there.
    In the mean time, $40 or less will buy you a very capable wireless router with four Ethernet ports and will simplify your network tremendously. Having used Windows ICS for a long time, the addition of a router and a real network simplified things so much.

  • I have iphone 4s , I'm not able to join any wifi, I have tried all the methods, resetting, trying different wifi and many others , but still not able to join any wifi , what shall I do?

    I have iphone 4s , I'm not able to join any wifi, I have tried many things, resetting, trying different wifi and many others , but still not able to join any wifi , what shall I do?

    Contact iTunes support. Nobody here can help with billing problems.

  • I have a MacBook 5,1 (13.3" aluminum from 2007 or 2008). Automatic updates will only let me get to OSX 10.5.8.  Can I upgrade to Snow Leopard, Lion 10.6 or even 10.6.8?  Also, will I have any issues with my iPhone if it's updated to iOS 7.1?

    I have a MacBook 5,1 (13.3" aluminum from 2007 or 2008). Automatic updates will only let me get to OSX 10.5.8.  Can I upgrade to Snow Leopard, Lion 10.6 or even 10.6.8?  Also, will I have any issues with my iPhone if it's updated to iOS 7.1?

    The 10.6 Snow Leopard DVD is in the Apple online store. You can get it for $19.99. You will need to be running 10.6.8 to access the App Store to order Lion or Mountain Lion. http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard
    System Requirements for 10.6:
    Mac computer with an Intel processor
    1GB of memory
    5GB of available disk space
    DVD drive for installation
    Some features require a compatible internet service provider: fees may apply.
    You can upgrade direct from 10.6.8 to 10.8 Mountain Lion without going through 10.7 Lion with the Late 2008 model 5,1 Aluminum Unibody. The Model 5,1 will probably run 10.9 Mavricks when it comes out.
    10.8 Mountain Lion is a download from the App Store, the price is $19.99.
    Mountain Lion will require at least 2gb of RAM but really needs 4gb to run smoothly.
    As for third party programs see this list for compatibility with 10.8 http://roaringapps.com/apps:table
    Also Mountain Lion doesn't run any Power PC programs. To see if you have any Power PC programs go to the Apple in the upper left corner and select About This Mac, then click on More Info. When System Profiler comes up select Applications under Software. Then look under Kind to see if any of your applications are listed as Power PC. Universal and Intel will run under Mountain Lion.
    Before Mac switched to Intel processors in 2006 they used Power PC processors from 1994 to 2005. Power PC 601 through 604, G3, G4 and G5. Applications written for the Power PC processors need the application called Rosetta to run on Intel processors. This was part of the Operating System in 10.4 and 10.5 but was an optional install in 10.6. With 10.7 Lion Apple dropped all support for Power PC applications.

  • Why can't I join a network with my IPhone with IOS7?

    Why can't I join a network with my IPhone with IOS7?

    Hi gvtxman,
    The articles below may be able to help you troubleshoot your Wi-Fi issue.
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/TS1398?viewlocale=en_US
    Reset network settings by tapping Settings > General > Reset > Reset Network Settings.
    Note: This will reset all network settings including previously connected Wi-Fi networks and passwords
    iOS and OS X: Recommended settings for Wi-Fi routers and access points
    http://support.apple.com/kb/HT4199
    I hope this information helps ....
    Have a great day!
    - Judy

  • Hy i Upgrade my iPhone and now my mp4 Data are in the file Video and i can't make any Playlist with them! Any idea?

    Hy i Upgrade my iPhone and now my mp4 Data are in the file Video and i can't make any Playlist with them! Any idea?

    I'm having the same issue, i restored my phone to Factory settings, even tried restoring it to my backup, half of my music bought from itunes won't play on my iphone and i'm super annoyed, this only happened once i updated to ios 7.2 so i assume its another glitch to go with my imessages not sending, getting sick of this.

  • TS1398 my iphone 4s can not scan any wifi network, i tried everything but still can not scan any wifi connection even though our wifi is working properly in our mac book and ipad. What do i need to do if the problem is the hardware?pls help

    my iphone 4s can not scan any wifi network, i tried everything but still can not scan any wifi connection even though our wifi is working properly in our mac book and ipad. What do i need to do if the problem is the hardware?pls help

    When you say it "can not scan any wifi network" do you mean it is not detecting Wi-Fi networks?
    Is Wi-Fi turned on in Settings > General > Wi-Fi?
    Have you tried Settings > General > Reset > Reset Network Settings?
    Is it just the home network that the device will not connect to? or any network?

Maybe you are looking for

  • IDVD 08 - problem with scene selection tabs not working after "burn"

    I have a movie that is about an hour long (made in iMovie08 using mostly still photos). I wanted to have "chapters" -- but with that option gone, I used the Scene Selection option in iDVD08. This created menus with 15 scene selection buttons (I chose

  • BADI for PO release through ME29n

    Hi Experts, I have to send an IDOC as & when user release the Purchase order from ME29n. I got a user exit 'M06E0004' for release strategy but it sends idoc when i open the Transaction ME29n. Instead of that i have to send it on the click on that rel

  • How to read attributes in to datagrid?

    hi i have one doubt in the datagrid we have header text but if we create dynamic datagrid and for (eg) <root> <data> <time datas="Hello"> <john  second="Karthikkkkkkkkk"></john> </time> </data> </root> if we want o make "datas" as header text what ca

  • Call settings

    I completed find call settings or call log settings Missing in BlackBerry 10 Does any one in BlackBerry 10 Os have call settings for received, Dialled and missed call? K G Desai

  • Parameters in try block..pls help

    I have the following code which I do not understand the reason it is not work. i.e. Putting the driver, dbURL, login, password value in the beginning work, however, setting it in the try blocks does not. Can you please help me? Thank you. public Conn