Can't load e17-svn after creation or /.e

Hi again! I insalled latest version of enlightenment. I glad to use these enviorment. But when I try to load it again then it doesn't load. I can't find any Howto's to fix it on Arch.
P.S. I use kdm to login.
Last edited by SkyTod (2009-09-13 11:50:43)

Whet it comes to enlightenment_start:
[ted@myhost ~]$ enlightenment_start
E - PID=1316, do_precache=0, valgrind=0
ESTART: 0.00001 [0.00001] - begin     
ESTART: 0.00067 [0.00067] - signals done
ESTART: 0.00328 [0.00261] - determine prefix
DYNAMIC DETERMINED PREFIX: /usr
ESTART: 0.06762 [0.06433] - prefix done
ESTART: 0.06827 [0.00065] - eina init
ESTART: 0.08789 [0.01962] - intl init
ESTART: 0.08850 [0.00061] - parse args
ESTART: 0.08903 [0.00054] - arg parse done
ESTART: 0.10991 [0.02088] - ecore init
ESTART: 0.13524 [0.02533] - ecore_file init
ESTART: 0.14173 [0.00649] - more ecore
ESTART: 0.14226 [0.00053] - x connect
ESTART: 0.16157 [0.01931] - ecore_con
ESTART: 0.16289 [0.00132] - xinerama
E17 INIT: XINERAMA SCREEN: [0], 1280x1024+0+0
E17 INIT: XINERAMA CHOSEN: [0], 1280x1024+0+0
ESTART: 0.16562 [0.00273] - x hints
ESTART: 0.16680 [0.00118] - x hints done
ESTART: 0.16727 [0.00046] - ecore_evas init
ESTART: 0.18558 [0.01831] - test done
ESTART: 0.18609 [0.00051] - efreet
ESTART: 0.18672 [0.00063] - efreet done
ESTART: 0.18716 [0.00044] - configure
ESTART: 0.18883 [0.00167] - dirs
ESTART: 0.20529 [0.01646] - filereg
ESTART: 0.20581 [0.00052] - config
ESTART: 0.23208 [0.02626] - scale
ESTART: 0.23267 [0.00060] - pointer
ESTART: 0.23310 [0.00042] - path
ESTART: 0.23347 [0.00038] - ipc
INFO: E_IPC_SOCKET=/tmp/enlightenment-ted/disp-:0.0-1316
ESTART: 0.23399 [0.00052] - font
ESTART: 0.23528 [0.00130] - theme
ESTART: 0.26061 [0.02532] - intl post
The locale '' cannot be found on your system. Please install this locale or try something else.ESTART: 0.31917 [0.05856] - splash
RUN INIT: /usr/lib/enlightenment/utils/enlightenment_init '/usr/share/enlightenment/data/themes/default.edj' '1' '0' 'Enlightenment' '0.16.999.062'

Similar Messages

  • Can't load photo book after crash

    Hello, after spending 2+ hours creating a photo book, my mac suddenly crashed, I think due to the high temperature of the computer. The iPhoto application was still running when the computer shut down. After rebooting, I can't load my photo book anymore. The application says "Loading Book", but it stays like this forever.
    Is it possible to recover, at least partially, the work that I was doing? Is there an actual "photo book" file somewhere in the computer?
    Thank you... I'm quite frustrated right now.

    In the future you could do what I do: create a new library for each book I make. I assemble the photos in my primary library into an album and move that album to the book library with iPhoto Library Manager. That makes for a smaller library which can be easier to backup and archive for use and ordering additional copies at a later date: Old Toad's Tutorial #9a - Archiving an iPhoto 7/8 Book for Use/Editing/Ordering at a Later Date.

  • Can't load pdf files after 10.4.11 update

    Since installing the 4.10.11 update I can't read any more the pdf files downloaded in Safari 3 as the page turns completely gray (I can read pdf files only after downloading them to the desktop). I have browsed the 4.10.11 troubles and answers hoping to find a cue, but nothing of the like seems to have happened yet...
    Is there something that I can do ?
    Thank you for any help !

    Have got exactly the same problem with Safari, but fine using Internet Explorer. Had a quick look on Adobe's update page - seems they only go up to 10.4.10... that may be problem???

  • Can't load nvidia module after kernel and nvidia update

    After latest kernel (3.6.36.2) and nvidia (260.19.29) upgrade xorg doesn't work. I investigated a little, and that's what I found:
    # modprobe nvidia
    FATAL: Error inserting nvidia (/lib/modules/2.6.36-ARCH/kernel/drivers/video/nvidia.ko): No such device
    I blacklisted nouveau module:
    # cat /etc/rc.conf | grep nouveau
    MODULES=(b43 vboxdrv !nouveau)
    but it didn't help.
    Video card:
    # lspci | grep VGA
    01:00.0 VGA compatible controller: nVidia Corporation G84 [GeForce 8600M GT] (rev a1)

    Initializing cgroup subsys cpuset
    Initializing cgroup subsys cpu
    Linux version 2.6.36-ARCH (tobias@T-POWA-LX) (gcc version 4.5.1 20101125 (prerelease) (GCC) ) #1 SMP PREEMPT Fri Dec 10 20:01:53 UTC 2010
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000005fed0000 (usable)
    BIOS-e820: 000000005fed0000 - 000000005fee3000 (ACPI NVS)
    BIOS-e820: 000000005fee3000 - 0000000060000000 (reserved)
    BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
    BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
    BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
    BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
    Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
    DMI present.
    e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
    e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    last_pfn = 0x5fed0 max_arch_pfn = 0x100000
    MTRR default type: uncachable
    MTRR fixed ranges enabled:
    00000-9FFFF write-back
    A0000-BFFFF uncachable
    C0000-FFFFF write-protect
    MTRR variable ranges enabled:
    0 base 000000000 mask FC0000000 write-back
    1 base 040000000 mask FE0000000 write-back
    2 base 05FF00000 mask FFFF00000 uncachable
    3 disabled
    4 disabled
    5 disabled
    6 disabled
    7 disabled
    x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    e820 update range: 0000000000002000 - 0000000000010000 (usable) ==> (reserved)
    Scanning 1 areas for low memory corruption
    modified physical RAM map:
    modified: 0000000000000000 - 0000000000001000 (reserved)
    modified: 0000000000001000 - 0000000000002000 (usable)
    modified: 0000000000002000 - 0000000000010000 (reserved)
    modified: 0000000000010000 - 000000000009f800 (usable)
    modified: 000000000009f800 - 00000000000a0000 (reserved)
    modified: 00000000000dc000 - 0000000000100000 (reserved)
    modified: 0000000000100000 - 000000005fed0000 (usable)
    modified: 000000005fed0000 - 000000005fee3000 (ACPI NVS)
    modified: 000000005fee3000 - 0000000060000000 (reserved)
    modified: 00000000fec00000 - 00000000fec10000 (reserved)
    modified: 00000000fed00000 - 00000000fed00400 (reserved)
    modified: 00000000fed14000 - 00000000fed1a000 (reserved)
    modified: 00000000fed1c000 - 00000000fed90000 (reserved)
    modified: 00000000fee00000 - 00000000fee01000 (reserved)
    modified: 00000000ff000000 - 0000000100000000 (reserved)
    initial memory mapped : 0 - 01800000
    found SMP MP-table at [c00f7bc0] f7bc0
    init_memory_mapping: 0000000000000000-00000000377fe000
    0000000000 - 0000400000 page 4k
    0000400000 - 0037400000 page 2M
    0037400000 - 00377fe000 page 4k
    kernel direct mapping tables up to 377fe000 @ 15000-1a000
    RAMDISK: 37e47000 - 37ff0000
    Allocated new RAMDISK: 00100000 - 002a8feb
    Move RAMDISK from 0000000037e47000 - 0000000037feffea to 00100000 - 002a8fea
    ACPI: RSDP 000f7b40 00024 (v02 Compal)
    ACPI: XSDT 5fed8834 0008C (v01 Compal CRESTLNE 06040000 LTP 00000000)
    ACPI: FACP 5fedfbd2 000F4 (v03 INTEL CRESTLNE 06040000 ALAN 00000001)
    ACPI: DSDT 5fed9b9f 05FBF (v02 Compal CRESTLNE 06040000 INTL 20061109)
    ACPI: FACS 5fee2fc0 00040
    ACPI: APIC 5fedfcc6 00068 (v01 INTEL CRESTLNE 06040000 LOHR 0000005A)
    ACPI: HPET 5fedfd2e 00038 (v01 Compal CRESTLNE 06040000 LOHR 0000005A)
    ACPI: MCFG 5fedfd66 0003C (v01 INTEL CRESTLNE 06040000 LOHR 0000005A)
    ACPI: TCPA 5fedfda2 00032 (v01 Intel CRESTLNE 06040000 LOHR 0000005A)
    ACPI: TMOR 5fedfdd4 00026 (v01 PTLTD 06040000 PTL 00000003)
    ACPI: SLIC 5fedfdfa 00176 (v01 Compal CRESTLNE 06040000 TBD 00000001)
    ACPI: APIC 5fedff70 00068 (v01 PTLTD ? APIC 06040000 LTP 00000000)
    ACPI: BOOT 5fedffd8 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001)
    ACPI: SSDT 5fed98da 002C5 (v01 SataRe SataAhci 00001000 INTL 20050624)
    ACPI: SSDT 5fed8e4c 0025F (v01 PmRef Cpu0Tst 00003000 INTL 20050624)
    ACPI: SSDT 5fed8da6 000A6 (v01 PmRef Cpu1Tst 00003000 INTL 20050624)
    ACPI: SSDT 5fed88c0 004E6 (v01 PmRef CpuPm 00003000 INTL 20050624)
    ACPI: BIOS bug: multiple APIC/MADT found, using 0
    ACPI: If "acpi_apic_instance=2" works better, notify [email protected]
    ACPI: Local APIC address 0xfee00000
    646MB HIGHMEM available.
    887MB LOWMEM available.
    mapped low ram: 0 - 377fe000
    low ram: 0 - 377fe000
    Zone PFN ranges:
    DMA 0x00000001 -> 0x00001000
    Normal 0x00001000 -> 0x000377fe
    HighMem 0x000377fe -> 0x0005fed0
    Movable zone start PFN for each node
    early_node_map[3] active PFN ranges
    0: 0x00000001 -> 0x00000002
    0: 0x00000010 -> 0x0000009f
    0: 0x00000100 -> 0x0005fed0
    On node 0 totalpages: 392800
    free_area_init_node: node 0, pgdat c142d600, node_mem_map c1598020
    DMA zone: 32 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 3952 pages, LIFO batch:0
    Normal zone: 1744 pages used for memmap
    Normal zone: 221486 pages, LIFO batch:31
    HighMem zone: 1294 pages used for memmap
    HighMem zone: 164292 pages, LIFO batch:31
    Using APIC driver default
    ACPI: PM-Timer IO Port: 0x1008
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Using ACPI (MADT) for SMP configuration information
    ACPI: HPET id: 0x8086a201 base: 0xfed00000
    SMP: Allowing 2 CPUs, 0 hotplug CPUs
    nr_irqs_gsi: 40
    early_res array is doubled to 64 at [16000 - 167ff]
    PM: Registered nosave memory: 0000000000002000 - 0000000000010000
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
    PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
    Allocating PCI resources starting at 60000000 (gap: 60000000:9ec00000)
    Booting paravirtualized kernel on bare hardware
    setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
    PERCPU: Embedded 13 pages/cpu @c2400000 s31488 r0 d21760 u2097152
    pcpu-alloc: s31488 r0 d21760 u2097152 alloc=1*4194304
    pcpu-alloc: [0] 0 1
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 389730
    Kernel command line: BOOT_IMAGE=/boot/vmlinuz26 root=/dev/sda2 ro
    PID hash table entries: 4096 (order: 2, 16384 bytes)
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    allocated 7858220 bytes of page_cgroup
    please try 'cgroup_disable=memory' option if you don't want memory cgroups
    Subtract (52 early reservations)
    #1 [0000001000 - 0000002000] EX TRAMPOLINE
    #2 [0001000000 - 000158fe8c] TEXT DATA BSS
    #3 [0001590000 - 0001596198] BRK
    #4 [00000f7bd0 - 0000100000] BIOS reserved
    #5 [00000f7bc0 - 00000f7bd0] MP-table mpf
    #6 [000009f800 - 000009fd71] BIOS reserved
    #7 [000009ff35 - 00000f7bc0] BIOS reserved
    #8 [000009fd71 - 000009ff35] MP-table mpc
    #9 [0000010000 - 0000011000] TRAMPOLINE
    #10 [0000011000 - 0000015000] ACPI WAKEUP
    #11 [0000015000 - 0000016000] PGTABLE
    #12 [0000100000 - 00002a9000] NEW RAMDISK
    #13 [0001597000 - 0001598000] BOOTMEM
    #14 [0001598000 - 0002198000] BOOTMEM
    #15 [000158fec0 - 000158fec4] BOOTMEM
    #16 [000158ff00 - 000158ffc0] BOOTMEM
    #17 [00015961c0 - 0001596214] BOOTMEM
    #18 [0002198000 - 000219b000] BOOTMEM
    #19 [000158ffc0 - 0001590000] BOOTMEM
    #20 [000219b000 - 000219e000] BOOTMEM
    #21 [0001596240 - 0001596265] BOOTMEM
    #22 [0001596280 - 00015962a7] BOOTMEM
    #23 [00015962c0 - 0001596464] BOOTMEM
    #24 [0001596480 - 00015964c0] BOOTMEM
    #25 [00015964c0 - 0001596500] BOOTMEM
    #26 [0001596500 - 0001596540] BOOTMEM
    #27 [0001596540 - 0001596580] BOOTMEM
    #28 [0001596580 - 00015965c0] BOOTMEM
    #29 [00015965c0 - 0001596600] BOOTMEM
    #30 [0001596600 - 0001596640] BOOTMEM
    #31 [0001596640 - 0001596680] BOOTMEM
    #32 [0001596680 - 00015966c0] BOOTMEM
    #33 [00015966c0 - 0001596700] BOOTMEM
    #34 [0001596700 - 0001596740] BOOTMEM
    #35 [0001596740 - 0001596780] BOOTMEM
    #36 [0001596780 - 0001596790] BOOTMEM
    #37 [00015967c0 - 00015967d0] BOOTMEM
    #38 [0001596800 - 000159682d] BOOTMEM
    #39 [0001596840 - 000159686d] BOOTMEM
    #40 [0002400000 - 000240d000] BOOTMEM
    #41 [0002600000 - 000260d000] BOOTMEM
    #42 [0001596880 - 0001596884] BOOTMEM
    #43 [00015968c0 - 00015968c4] BOOTMEM
    #44 [0001596900 - 0001596908] BOOTMEM
    #45 [0001596940 - 0001596948] BOOTMEM
    #46 [0001596980 - 0001596a28] BOOTMEM
    #47 [0001596a40 - 0001596aa8] BOOTMEM
    #48 [000219e000 - 00021a2000] BOOTMEM
    #49 [00021a2000 - 0002222000] BOOTMEM
    #50 [0002222000 - 0002262000] BOOTMEM
    #51 [000260d000 - 0002d8b82c] BOOTMEM
    Initializing HighMem for node 0 (000377fe:0005fed0)
    Memory: 1542868k/1571648k available (3104k kernel code, 28332k reserved, 1205k data, 428k init, 662344k highmem)
    virtual kernel memory layout:
    fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
    lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
    .init : 0xc1436000 - 0xc14a1000 ( 428 kB)
    .data : 0xc1308056 - 0xc1435820 (1205 kB)
    .text : 0xc1000000 - 0xc1308056 (3104 kB)
    Checking if this processor honours the WP bit even in supervisor mode...Ok.
    SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    Hierarchical RCU implementation.
    RCU-based detection of stalled CPUs is disabled.
    Verbose stalled-CPUs detection is disabled.
    NR_IRQS:512
    Extended CMOS year: 2000
    Console: colour VGA+ 80x25
    console [tty0] enabled
    hpet clockevent registered
    Fast TSC calibration using PIT
    Detected 1795.546 MHz processor.
    Calibrating delay loop (skipped), value calculated using timer frequency.. 3592.72 BogoMIPS (lpj=5985153)
    pid_max: default: 32768 minimum: 301
    Security Framework initialized
    TOMOYO Linux initialized
    AppArmor: AppArmor disabled by boot time parameter
    Mount-cache hash table entries: 512
    Initializing cgroup subsys ns
    Initializing cgroup subsys cpuacct
    Initializing cgroup subsys memory
    Initializing cgroup subsys devices
    Initializing cgroup subsys freezer
    Initializing cgroup subsys net_cls
    Initializing cgroup subsys blkio
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 0
    mce: CPU supports 6 MCE banks
    CPU0: Thermal monitoring handled by SMI
    using mwait in idle threads.
    Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
    PEBS disabled due to CPU errata.
    ... version: 2
    ... bit width: 40
    ... generic registers: 2
    ... value mask: 000000ffffffffff
    ... max period: 000000007fffffff
    ... fixed-purpose events: 3
    ... event mask: 0000000700000003
    ACPI: Core revision 20100702
    Enabling APIC mode: Flat. Using 1 I/O APICs
    ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    CPU0: Intel(R) Core(TM)2 Duo CPU T7100 @ 1.80GHz stepping 0d
    NMI watchdog enabled, takes one hw-pmu counter.
    Booting Node 0, Processors #1 Ok.
    Initializing CPU#1
    CPU1: Thermal monitoring handled by SMI
    NMI watchdog enabled, takes one hw-pmu counter.
    Brought up 2 CPUs
    Total of 2 processors activated (7184.34 BogoMIPS).
    devtmpfs: initialized
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    PCI: not using MMCONFIG
    PCI: PCI BIOS revision 2.10 entry at 0xfdde1, last bus=14
    PCI: Using configuration type 1 for base access
    bio: create slab <bio-0> at 0
    ACPI: EC: Look up EC in DSDT
    ACPI: BIOS _OSI(Linux) query ignored
    ACPI: SSDT 5fed95da 00238 (v01 PmRef Cpu0Ist 00003000 INTL 20050624)
    ACPI: Dynamic OEM Table Load:
    ACPI: SSDT (null) 00238 (v01 PmRef Cpu0Ist 00003000 INTL 20050624)
    ACPI: SSDT 5fed90ab 004AA (v01 PmRef Cpu0Cst 00003001 INTL 20050624)
    ACPI: Dynamic OEM Table Load:
    ACPI: SSDT (null) 004AA (v01 PmRef Cpu0Cst 00003001 INTL 20050624)
    ACPI: SSDT 5fed9812 000C8 (v01 PmRef Cpu1Ist 00003000 INTL 20050624)
    ACPI: Dynamic OEM Table Load:
    ACPI: SSDT (null) 000C8 (v01 PmRef Cpu1Ist 00003000 INTL 20050624)
    ACPI: SSDT 5fed9555 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20050624)
    ACPI: Dynamic OEM Table Load:
    ACPI: SSDT (null) 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20050624)
    ACPI: Interpreter enabled
    ACPI: (supports S0 S3 S4 S5)
    ACPI: Using IOAPIC for interrupt routing
    PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
    PCI: Using MMCONFIG for extended config space
    ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
    ACPI: No dock devices found.
    PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
    ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
    pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
    pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
    pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff] (ignored)
    pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff] (ignored)
    pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff] (ignored)
    pci_root PNP0A08:00: host bridge window [mem 0x60000000-0xdfffffff] (ignored)
    pci_root PNP0A08:00: host bridge window [mem 0xf0000000-0xfebfffff] (ignored)
    pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:01.0: PME# disabled
    pci 0000:00:1a.0: reg 20: [io 0x1800-0x181f]
    pci 0000:00:1a.1: reg 20: [io 0x1820-0x183f]
    pci 0000:00:1a.7: reg 10: [mem 0xf8404800-0xf8404bff]
    pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
    pci 0000:00:1a.7: PME# disabled
    pci 0000:00:1b.0: reg 10: [mem 0xf8400000-0xf8403fff 64bit]
    pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:1b.0: PME# disabled
    pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.0: PME# disabled
    pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.1: PME# disabled
    pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.2: PME# disabled
    pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.3: PME# disabled
    pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.4: PME# disabled
    pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.5: PME# disabled
    pci 0000:00:1d.0: reg 20: [io 0x1840-0x185f]
    pci 0000:00:1d.1: reg 20: [io 0x1860-0x187f]
    pci 0000:00:1d.2: reg 20: [io 0x1880-0x189f]
    pci 0000:00:1d.7: reg 10: [mem 0xf8404c00-0xf8404fff]
    pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    pci 0000:00:1d.7: PME# disabled
    pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH6 ACPI/GPIO/TCO
    pci 0000:00:1f.0: quirk: [io 0x1180-0x11bf] claimed by ICH6 GPIO
    pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
    pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0068 (mask 0007)
    pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 1640 (mask 007f)
    pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
    pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
    pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
    pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
    pci 0000:00:1f.1: reg 20: [io 0x18a0-0x18af]
    pci 0000:00:1f.2: reg 10: [io 0x18d8-0x18df]
    pci 0000:00:1f.2: reg 14: [io 0x18cc-0x18cf]
    pci 0000:00:1f.2: reg 18: [io 0x18d0-0x18d7]
    pci 0000:00:1f.2: reg 1c: [io 0x18c8-0x18cb]
    pci 0000:00:1f.2: reg 20: [io 0x18e0-0x18ff]
    pci 0000:00:1f.2: reg 24: [mem 0xf8404000-0xf84047ff]
    pci 0000:00:1f.2: PME# supported from D3hot
    pci 0000:00:1f.2: PME# disabled
    pci 0000:00:1f.3: reg 10: [mem 0x00000000-0x000000ff]
    pci 0000:00:1f.3: reg 20: [io 0x1c00-0x1c1f]
    pci 0000:01:00.0: reg 10: [mem 0xc6000000-0xc6ffffff]
    pci 0000:01:00.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
    pci 0000:01:00.0: reg 1c: [mem 0xc4000000-0xc5ffffff 64bit]
    pci 0000:01:00.0: reg 24: [io 0x2000-0x207f]
    pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
    pci 0000:00:01.0: PCI bridge to [bus 01-01]
    pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
    pci 0000:00:01.0: bridge window [mem 0xc4000000-0xc6ffffff]
    pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    pci 0000:00:1c.0: PCI bridge to [bus 02-02]
    pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
    pci 0000:00:1c.0: bridge window [mem 0xbc000000-0xbfffffff]
    pci 0000:00:1c.0: bridge window [mem 0xcc000000-0xcdffffff 64bit pref]
    pci 0000:04:00.0: reg 10: [mem 0xf0000000-0xf000ffff 64bit]
    pci 0000:04:00.0: PME# supported from D3hot D3cold
    pci 0000:04:00.0: PME# disabled
    pci 0000:00:1c.1: PCI bridge to [bus 04-04]
    pci 0000:00:1c.1: bridge window [io 0x4000-0x4fff]
    pci 0000:00:1c.1: bridge window [mem 0xf0000000-0xf3ffffff]
    pci 0000:00:1c.1: bridge window [mem 0xfa000000-0xfbffffff 64bit pref]
    pci 0000:00:1c.2: PCI bridge to [bus 06-06]
    pci 0000:00:1c.2: bridge window [io 0x5000-0x5fff]
    pci 0000:00:1c.2: bridge window [mem 0xf4000000-0xf7ffffff]
    pci 0000:00:1c.2: bridge window [mem 0xfc000000-0xfdffffff 64bit pref]
    pci 0000:00:1c.3: PCI bridge to [bus 08-08]
    pci 0000:00:1c.3: bridge window [io 0x6000-0x6fff]
    pci 0000:00:1c.3: bridge window [mem 0xb4000000-0xb7ffffff]
    pci 0000:00:1c.3: bridge window [mem 0xc8000000-0xc9ffffff 64bit pref]
    pci 0000:00:1c.4: PCI bridge to [bus 0a-0a]
    pci 0000:00:1c.4: bridge window [io 0xf000-0x0000] (disabled)
    pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff] (disabled)
    pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    pci 0000:0c:00.0: reg 10: [mem 0xf8000000-0xf8003fff]
    pci 0000:0c:00.0: supports D1 D2
    pci 0000:0c:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    pci 0000:00:1c.5: PCI bridge to [bus 0c-0c]
    pci 0000:00:1c.5: bridge window [io 0xf000-0x0000] (disabled)
    pci 0000:00:1c.5: bridge window [mem 0xf8000000-0xf80fffff]
    pci 0000:00:1c.5: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    pci 0000:0e:06.0: proprietary Ricoh MMC controller disabled (via firewire function)
    pci 0000:0e:06.0: MMC cards are now supported by standard SDHCI controller
    pci 0000:0e:06.0: reg 10: [mem 0xf8100000-0xf81007ff]
    pci 0000:0e:06.0: supports D1 D2
    pci 0000:0e:06.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:0e:06.0: PME# disabled
    pci 0000:0e:06.1: reg 10: [mem 0xf8100800-0xf81008ff]
    pci 0000:0e:06.1: supports D1 D2
    pci 0000:0e:06.1: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:0e:06.1: PME# disabled
    pci 0000:0e:06.2: reg 10: [mem 0xf8101000-0xf81010ff]
    pci 0000:0e:06.2: supports D1 D2
    pci 0000:0e:06.2: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:0e:06.2: PME# disabled
    pci 0000:00:1e.0: PCI bridge to [bus 0e-0e] (subtractive decode)
    pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
    pci 0000:00:1e.0: bridge window [mem 0xf8100000-0xf81fffff]
    pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
    pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
    pci_bus 0000:00: on NUMA node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
    ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
    ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
    ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
    ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
    HEST: Table is not found!
    vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    vgaarb: loaded
    PCI: Using ACPI for IRQ routing
    PCI: pci_cache_line_size set to 64 bytes
    reserve RAM buffer: 0000000000002000 - 000000000000ffff
    reserve RAM buffer: 000000000009f800 - 000000000009ffff
    reserve RAM buffer: 000000005fed0000 - 000000005fffffff
    NetLabel: Initializing
    NetLabel: domain hash size = 128
    NetLabel: protocols = UNLABELED CIPSOv4
    NetLabel: unlabeled traffic allowed by default
    HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    Switching to clocksource tsc
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp: PnP ACPI: found 10 devices
    ACPI: ACPI bus type pnp unregistered
    system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
    system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
    system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
    system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
    system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
    system 00:01: [mem 0xfed20000-0xfed3ffff] has been reserved
    system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved
    system 00:01: [mem 0xfed45000-0xfed8ffff] has been reserved
    system 00:04: [mem 0xfed00000-0xfed003ff] has been reserved
    system 00:06: [io 0x0680-0x069f] has been reserved
    system 00:06: [io 0x0800-0x080f] has been reserved
    system 00:06: [io 0x1000-0x107f] has been reserved
    system 00:06: [io 0x1180-0x11bf] has been reserved
    system 00:06: [io 0x1640-0x164f] has been reserved
    system 00:06: [io 0xfe00] has been reserved
    system 00:06: [io 0xff00-0xff7f] has been reserved
    pci 0000:00:1c.4: BAR 14: assigned [mem 0x60000000-0x601fffff]
    pci 0000:00:1c.4: BAR 15: assigned [mem 0x60200000-0x603fffff 64bit pref]
    pci 0000:00:1c.5: BAR 15: assigned [mem 0x60400000-0x605fffff 64bit pref]
    pci 0000:00:1c.4: BAR 13: assigned [io 0x7000-0x7fff]
    pci 0000:00:1c.5: BAR 13: assigned [io 0x8000-0x8fff]
    pci 0000:00:1f.3: BAR 0: assigned [mem 0x60600000-0x606000ff]
    pci 0000:00:1f.3: BAR 0: set to [mem 0x60600000-0x606000ff] (PCI address [0x60600000-0x606000ff]
    pci 0000:01:00.0: BAR 6: can't assign mem pref (size 0x20000)
    pci 0000:00:01.0: PCI bridge to [bus 01-01]
    pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
    pci 0000:00:01.0: bridge window [mem 0xc4000000-0xc6ffffff]
    pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    pci 0000:00:1c.0: PCI bridge to [bus 02-02]
    pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
    pci 0000:00:1c.0: bridge window [mem 0xbc000000-0xbfffffff]
    pci 0000:00:1c.0: bridge window [mem 0xcc000000-0xcdffffff 64bit pref]
    pci 0000:00:1c.1: PCI bridge to [bus 04-04]
    pci 0000:00:1c.1: bridge window [io 0x4000-0x4fff]
    pci 0000:00:1c.1: bridge window [mem 0xf0000000-0xf3ffffff]
    pci 0000:00:1c.1: bridge window [mem 0xfa000000-0xfbffffff 64bit pref]
    pci 0000:00:1c.2: PCI bridge to [bus 06-06]
    pci 0000:00:1c.2: bridge window [io 0x5000-0x5fff]
    pci 0000:00:1c.2: bridge window [mem 0xf4000000-0xf7ffffff]
    pci 0000:00:1c.2: bridge window [mem 0xfc000000-0xfdffffff 64bit pref]
    pci 0000:00:1c.3: PCI bridge to [bus 08-08]
    pci 0000:00:1c.3: bridge window [io 0x6000-0x6fff]
    pci 0000:00:1c.3: bridge window [mem 0xb4000000-0xb7ffffff]
    pci 0000:00:1c.3: bridge window [mem 0xc8000000-0xc9ffffff 64bit pref]
    pci 0000:00:1c.4: PCI bridge to [bus 0a-0a]
    pci 0000:00:1c.4: bridge window [io 0x7000-0x7fff]
    pci 0000:00:1c.4: bridge window [mem 0x60000000-0x601fffff]
    pci 0000:00:1c.4: bridge window [mem 0x60200000-0x603fffff 64bit pref]
    pci 0000:00:1c.5: PCI bridge to [bus 0c-0c]
    pci 0000:00:1c.5: bridge window [io 0x8000-0x8fff]
    pci 0000:00:1c.5: bridge window [mem 0xf8000000-0xf80fffff]
    pci 0000:00:1c.5: bridge window [mem 0x60400000-0x605fffff 64bit pref]
    pci 0000:00:1e.0: PCI bridge to [bus 0e-0e]
    pci 0000:00:1e.0: bridge window [io disabled]
    pci 0000:00:1e.0: bridge window [mem 0xf8100000-0xf81fffff]
    pci 0000:00:1e.0: bridge window [mem pref disabled]
    pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    pci 0000:00:01.0: setting latency timer to 64
    pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    pci 0000:00:1c.0: setting latency timer to 64
    pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
    pci 0000:00:1c.1: setting latency timer to 64
    pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    pci 0000:00:1c.2: setting latency timer to 64
    pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
    pci 0000:00:1c.3: setting latency timer to 64
    pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    pci 0000:00:1c.4: setting latency timer to 64
    pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
    pci 0000:00:1c.5: setting latency timer to 64
    pci 0000:00:1e.0: setting latency timer to 64
    pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
    pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
    pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
    pci_bus 0000:01: resource 1 [mem 0xc4000000-0xc6ffffff]
    pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
    pci_bus 0000:02: resource 0 [io 0x3000-0x3fff]
    pci_bus 0000:02: resource 1 [mem 0xbc000000-0xbfffffff]
    pci_bus 0000:02: resource 2 [mem 0xcc000000-0xcdffffff 64bit pref]
    pci_bus 0000:04: resource 0 [io 0x4000-0x4fff]
    pci_bus 0000:04: resource 1 [mem 0xf0000000-0xf3ffffff]
    pci_bus 0000:04: resource 2 [mem 0xfa000000-0xfbffffff 64bit pref]
    pci_bus 0000:06: resource 0 [io 0x5000-0x5fff]
    pci_bus 0000:06: resource 1 [mem 0xf4000000-0xf7ffffff]
    pci_bus 0000:06: resource 2 [mem 0xfc000000-0xfdffffff 64bit pref]
    pci_bus 0000:08: resource 0 [io 0x6000-0x6fff]
    pci_bus 0000:08: resource 1 [mem 0xb4000000-0xb7ffffff]
    pci_bus 0000:08: resource 2 [mem 0xc8000000-0xc9ffffff 64bit pref]
    pci_bus 0000:0a: resource 0 [io 0x7000-0x7fff]
    pci_bus 0000:0a: resource 1 [mem 0x60000000-0x601fffff]
    pci_bus 0000:0a: resource 2 [mem 0x60200000-0x603fffff 64bit pref]
    pci_bus 0000:0c: resource 0 [io 0x8000-0x8fff]
    pci_bus 0000:0c: resource 1 [mem 0xf8000000-0xf80fffff]
    pci_bus 0000:0c: resource 2 [mem 0x60400000-0x605fffff 64bit pref]
    pci_bus 0000:0e: resource 1 [mem 0xf8100000-0xf81fffff]
    pci_bus 0000:0e: resource 4 [io 0x0000-0xffff]
    pci_bus 0000:0e: resource 5 [mem 0x00000000-0xffffffff]
    NET: Registered protocol family 2
    IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    TCP: Hash tables configured (established 131072 bind 65536)
    TCP reno registered
    UDP hash table entries: 512 (order: 2, 16384 bytes)
    UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    NET: Registered protocol family 1
    PCI: CLS 64 bytes, default 64
    Unpacking initramfs...
    Freeing initrd memory: 1700k freed
    Simple Boot Flag at 0x38 set to 0x1
    apm: BIOS not found.
    Scanning for low memory corruption every 60 seconds
    audit: initializing netlink socket (disabled)
    type=2000 audit(1294159792.419:1): initialized
    highmem bounce pool size: 64 pages
    HugeTLB registered 4 MB page size, pre-allocated 0 pages
    VFS: Disk quotas dquot_6.5.2
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    msgmni has been set to 1723
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    io scheduler noop registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    intel_idle: MWAIT substates: 0x22220
    intel_idle: does not run on family 6 model 15
    ERST: Table is not found!
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    rtc_cmos 00:07: RTC can wake from S4
    rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
    cpuidle: using governor ladder
    cpuidle: using governor menu
    TCP cubic registered
    NET: Registered protocol family 17
    Registering the dns_resolver key type
    Using IPI No-Shortcut mode
    PM: Resume from disk failed.
    registered taskstats version 1
    rtc_cmos 00:07: setting system clock to 2011-01-04 16:49:53 UTC (1294159793)
    Initalizing network drop monitor service
    Freeing unused kernel memory: 428k freed
    udev[38]: starting version 165
    input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    SCSI subsystem initialized
    libata version 3.00 loaded.
    ahci 0000:00:1f.2: version 3.0
    ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    ahci 0000:00:1f.2: irq 40 for MSI/MSI-X
    ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
    ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc
    ahci 0000:00:1f.2: setting latency timer to 64
    scsi0 : ahci
    scsi1 : ahci
    scsi2 : ahci
    ata1: SATA max UDMA/133 abar m2048@0xf8404000 port 0xf8404100 irq 40
    ata2: SATA max UDMA/133 abar m2048@0xf8404000 port 0xf8404180 irq 40
    ata3: SATA max UDMA/133 abar m2048@0xf8404000 port 0xf8404200 irq 40
    ata_piix 0000:00:1f.1: version 2.13
    ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
    ata_piix 0000:00:1f.1: setting latency timer to 64
    scsi3 : ata_piix
    scsi4 : ata_piix
    ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18a0 irq 14
    ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18a8 irq 15
    ata4.00: ATAPI: Slimtype DVDRW SSM-8515S, GS09, max UDMA/33
    ata4.00: configured for UDMA/33
    ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata2: SATA link down (SStatus 0 SControl 300)
    ata3: SATA link down (SStatus 0 SControl 300)
    ata1.00: unexpected _GTF length (8)
    ata1.00: ATA-8: ST9320423AS, 0002SDM1, max UDMA/133
    ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
    ata1.00: unexpected _GTF length (8)
    ata1.00: configured for UDMA/133
    scsi 0:0:0:0: Direct-Access ATA ST9320423AS 0002 PQ: 0 ANSI: 5
    scsi 3:0:0:0: CD-ROM Slimtype DVDRW SSM-8515S GS09 PQ: 0 ANSI: 5
    sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
    sd 0:0:0:0: [sda] Attached SCSI disk
    sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    cdrom: Uniform CD-ROM driver Revision: 3.20
    sr 3:0:0:0: Attached scsi CD-ROM sr0
    EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
    Not activating Mandatory Access Control now since /sbin/tomoyo-init doesn't exist.
    udev[839]: starting version 165
    input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
    ACPI: Lid Switch [LID0]
    input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
    ACPI: Power Button [PWRB]
    input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    ACPI: Power Button [PWRF]
    ACPI: acpi_idle registered with cpuidle
    Monitor-Mwait will be used to enter C-1 state
    Monitor-Mwait will be used to enter C-2 state
    Monitor-Mwait will be used to enter C-3 state
    Marking TSC unstable due to TSC halts in idle
    input: PC Speaker as /devices/platform/pcspkr/input/input4
    Switching to clocksource hpet
    compal-laptop: Identified laptop model 'FL90/IFL90'
    cfg80211: Calling CRDA to update world regulatory domain
    compal-laptop: Driver 0.2.7 successfully loaded
    i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
    Linux agpgart interface v0.103
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    iTCO_vendor_support: vendor-support=0
    sdhci: Secure Digital Host Controller Interface driver
    sdhci: Copyright(c) Pierre Ossman
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    sdhci-pci 0000:0e:06.1: SDHCI controller found [1180:0822] (rev 22)
    sdhci-pci 0000:0e:06.1: PCI INT B -> GSI 23 (level, low) -> IRQ 23
    sdhci-pci 0000:0e:06.1: Will use DMA mode even though HW doesn't fully claim to support it.
    Registered led device: mmc0::
    mmc0: SDHCI controller on PCI [0000:0e:06.1] using DMA
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    sr 3:0:0:0: Attached scsi generic sg1 type 5
    ACPI: Battery Slot [BAT1] (battery present)
    ACPI: WMI: Mapper loaded
    ACPI: AC Adapter [ACAD] (on-line)
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    acpi device:03: registered as cooling_device2
    input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input5
    ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
    b43-pci-bridge 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    b43-pci-bridge 0000:0c:00.0: setting latency timer to 64
    ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x11, vendor 0x4243)
    ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0A, vendor 0x4243)
    ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x03, vendor 0x4243)
    ssb: Core 3 found: PCI-E (cc 0x820, rev 0x01, vendor 0x4243)
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    ehci_hcd 0000:00:1a.7: setting latency timer to 64
    ehci_hcd 0000:00:1a.7: EHCI Host Controller
    ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1a.7: debug port 1
    ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
    ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf8404800
    ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 4 ports detected
    ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
    ehci_hcd 0000:00:1d.7: setting latency timer to 64
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
    ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8404c00
    ssb: Sonics Silicon Backplane found on PCI device 0000:0c:00.0
    ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 6 ports detected
    firewire_ohci 0000:0e:06.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
    iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
    iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
    iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    psmouse serio1: ID: 10 00 64
    firewire_ohci: Added fw-ohci device 0000:0e:06.0, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x1
    uhci_hcd: USB Universal Host Controller Interface driver
    uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    uhci_hcd 0000:00:1a.0: setting latency timer to 64
    uhci_hcd 0000:00:1a.0: UHCI Host Controller
    uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
    uhci_hcd 0000:00:1a.1: setting latency timer to 64
    uhci_hcd 0000:00:1a.1: UHCI Host Controller
    uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
    uhci_hcd 0000:00:1d.0: setting latency timer to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
    uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    uhci_hcd 0000:00:1d.1: setting latency timer to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
    uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860
    hub 6-0:1.0: USB hub found
    hub 6-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    uhci_hcd 0000:00:1d.2: setting latency timer to 64
    uhci_hcd 0000:00:1d.2: UHCI Host Controller
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
    uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
    hub 7-0:1.0: USB hub found
    hub 7-0:1.0: 2 ports detected
    tg3.c:v3.113 (August 2, 2010)
    tg3 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    tg3 0000:04:00.0: setting latency timer to 64
    tg3 0000:04:00.0: vpd r/w failed. This is likely a firmware bug on this device. Contact the card vendor for a firmware update.
    usb 1-2: new high speed USB device using ehci_hcd and address 2
    tg3 0000:04:00.0: vpd r/w failed. This is likely a firmware bug on this device. Contact the card vendor for a firmware update.
    elantech: assuming hardware version 1, firmware version 2.0.4
    tg3 0000:04:00.0: vpd r/w failed. This is likely a firmware bug on this device. Contact the card vendor for a firmware update.
    tg3 0000:04:00.0: eth0: Tigon3 [partno(none) rev b002] (PCI Express) MAC address 00:1b:38:55:15:a4
    tg3 0000:04:00.0: eth0: attached PHY is 5787 (10/100/1000Base-T Ethernet) (WireSpeed[1])
    tg3 0000:04:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
    tg3 0000:04:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]
    elantech: Synaptics capabilities query result 0x10, 0x02, 0x64.
    HDA Intel 0000:00:1b.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    HDA Intel 0000:00:1b.0: irq 41 for MSI/MSI-X
    HDA Intel 0000:00:1b.0: setting latency timer to 64
    input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
    firewire_core: created device fw0: GUID 00023f79b240229a, S400
    b43-phy0: Broadcom 4311 WLAN found (core revision 10)
    nvidia: module license 'NVIDIA' taints kernel.
    Disabling lock debugging due to kernel taint
    phy0: Selected rate control algorithm 'minstrel_ht'
    Registered led device: b43-phy0::tx
    Registered led device: b43-phy0::rx
    Registered led device: b43-phy0::radio
    Broadcom 43xx driver loaded [ Features: PMLS, Firmware-ID: FW13 ]
    input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input7
    Linux video capture interface: v2.00
    uvcvideo: Found UVC 1.00 device USB 2.0 Camera (04f2:b018)
    input: USB 2.0 Camera as /devices/pci0000:00/0000:00:1a.7/usb1/1-2/1-2:1.0/input/input8
    usbcore: registered new interface driver uvcvideo
    USB Video Class driver (v0.1.0)
    nvidia 0000:01:00.0: power state changed by ACPI to D0
    nvidia 0000:01:00.0: power state changed by ACPI to D0
    nvidia 0000:01:00.0: enabling device (0000 -> 0003)
    nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    nvidia 0000:01:00.0: setting latency timer to 64
    vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
    NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:0407) installed
    NVRM: in this system is not supported by the 260.19.29 NVIDIA Linux
    NVRM: graphics driver release. Please see 'Appendix A -
    NVRM: Supported NVIDIA GPU Products' in this release's README,
    NVRM: available on the Linux graphics driver download page at
    NVRM: www.nvidia.com.
    nvidia: probe of 0000:01:00.0 failed with error -1
    NVRM: The NVIDIA probe routine failed for 1 device(s).
    NVRM: None of the NVIDIA graphics adapters were initialized!
    EXT4-fs (sda2): re-mounted. Opts: (null)
    EXT4-fs (sda2): re-mounted. Opts: (null)
    EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
    fuse init (API version 7.15)
    Adding 3156768k swap on /dev/sda3. Priority:-1 extents:1 across:3156768k
    nvidia 0000:01:00.0: setting latency timer to 64
    vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=io+mem
    NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:0407) installed
    NVRM: in this system is not supported by the 260.19.29 NVIDIA Linux
    NVRM: graphics driver release. Please see 'Appendix A -
    NVRM: Supported NVIDIA GPU Products' in this release's README,
    NVRM: available on the Linux graphics driver download page at
    NVRM: www.nvidia.com.
    nvidia: probe of 0000:01:00.0 failed with error -1
    NVRM: The NVIDIA probe routine failed for 1 device(s).
    NVRM: None of the NVIDIA graphics adapters were initialized!
    last lines looks interesting, but I also checked mentioned Appendix A of README, and I found 8600M GT (PCI ID 0x0407) between supported chips.

  • Can't load A2 library after installing A3 trial

    I renamed A2, installed the A3 trial, it said it can't touch my A2 library. I worked in A3, created a temp library and imported some pics (left my original A2 library alone) and found it much slower on my computer, so quit and went back to launch A2. When I do, it says "The library in “/Volumes/PhotosVideosMusic/Aperture 3 Trial Library.aplibrary” cannot be loaded because it is from a newer version of Aperture." And only gives me the option to Quit.
    How do I get my A2 library to launch????????

    There is no A3 or A2 preferences, they're both using the same preference file.
    Hold the option (or alt) key and launch ap2 and then select choose Library from the resulting menu. Choose your Ap 2 Library.
    Should you use Ap 3 again, then hold the option (or alt) key while launching, this time choose the 3 Library.
    As long remember to use the option (or alt) key on launch you'll be okay.
    Regards
    TD

  • Can't load lightroom trial after upgrading from 5 to CC.

    I was half way through my lightroom 5 trial when I upgraded to lightroom CC. the application manager still comes up asking if I want to continue my trial, but when I click on that it doesn't load lightroom.
    I have completely uninstalled both versions (manually for 5, as per the instruction on the Adobe site) and with the uninstaller for CC, and then reinstalled lightroom CC, but still it won't load.
    Does anyone else have this problem?

    OS x 10.10.3.
    Yes, lightroom cc (2015) is listed in the Creative cloud as installed.
    When I click on the app in the Creative cloud drop down the Lightroom app appears briefly in the dock, then the application manager appears and the lightroom icon disappears. After clicking the "continue trial" button in the application manager it closes and lightroom does not open.
    I have tried uninstalling and reinstalling several times, but no change.

  • Can we change material type after creation of material

    hi all ,
       can any body tell me how we can change the material type of already created material , i have a material type (do not use raw material) which i want to chage in raw material
    please reply

    Hi Manjit
    Try transaction MMAM
    It may not work if you have some differences in field selection between the old material type and the new material type (e.g. batch mandatory in old material type and hidden in new material type)
    It may not allow processing if stock has already been posted
    Regards
    Steve

  • Can't load LiveType or After Effects...

    They both unexpectedly quit as soon as I open them.
    What do i do?
    Alex

    I'm really sorry, I have no clue where to even suggest you start looking.
    <
    It's not that we're ignoring you.
    Your situation is beyond our ability to debug it by remote control. Well, let me restate that, it's beyond MY ability to debug it for you from Idaho.
    Scorched Earth Solution: Reformat your system drive and reinstall all of your software again from scratch, only takes a few hours. That is probably the quickest path but all it will do is eliminate one possible but highly unlikely — and equally inexplicable — issue: bad joojoo. There's only a 50-50 chance reformatting will cure anything.
    Try the After Effects forum on creativecow.net?
    bogiesan

  • Can't load php_oci8.dll after xampp update

    Hello,
    I tried to update Xampp with apache 2.0.52 and PHP 5.0.2 and oci8 rev 1.257 to apache 2.2.2 and PHP 5.1.4 .
    I uncommentet the line extension=php_oci8.dll and the extension directory is correctly set by xampp.
    And the first environment Path of the System is still linked to ...\oracle\ora92\bin .
    Starting the Apache server I get the error message: "The procedure entry point OCILobRead2 could not be located in the dynamic link library OCI.dll"
    With the old version the only thing I had to do was uncommenting the extension line, but with the new version it simply doesn't want to work.
    After renaming my backup folder with the old server everything is working again. But not the new version.
    Thanks for any help!
    Message was edited by:
    user525100

    Let's continue here, shall we?
    PHP Oracle connection randomly slow

  • Can't load / open itunes after lion install, help

    i justed purchased a used mac mini 2.26 ghz intel core 2 duo with 2gb.  the prior owner updated the os Mac OS X Lion vesion 10.7 prior to me buying.  I cannot open Itunes and I have received different error messages upon different attempts.  they range from : Reason: unsafe use of executable path in /a;;ications/ituens.app/contents/macos/ituens with restricted binary" - got this with a 10.3 download of itunes, to "check system to see if itunes is compatible with this version of Mac OS - got that one with 10.5 download.
    I have also tried downloading the software under a guest admin as well as a root user as mentioned in other threads, all to no avail.  Am i missing something, has apple come up with a fix, do i need to go buy a full version of the OS and do a reinstall?  very frustrating for my attempt to get a Mac to see how i like them before plunking down 2k on a full blow imac.
    any help would be appreciated.

    i notice that when i attempt a download and install and get another error message, when i go to itunes and do a command i (to get to the itunes software summary), it shows the isntall date as July 19, 2011.  apparatnly i am not deleting itunes fully as it seems to go back to the July 19 install when viewing the software.  new to mac and file system, why is this happening? maybe this is part of the problem

  • After upgrading to Solaris 10 "Can't load the root filesystem" on V245

    I have a Sunfire V245 that was running on Solaris 9 (very stable). I upgraded to Solaris 10 (6/06) this morning and everything seemed to go smoothly. After the upgrade the system rebooted, but will not boot. I get the following uptput;
    Rebooting with command: boot
    Boot device: disk File and args:
    SunOS Release 5.10 Version Generic_118833-17 64-bit
    Copyright 1983-2005 Sun Microsystems, Inc. All rights reserved.
    Use is subject to license terms.
    pxb_bcm: cannot load driver
    Cannot load drivers for /pci@1e,600000/pci@0/pci@a/pci@0/pci@8/scsi@1/disk@0,0:a
    Can't load the root filesystem
    Type 'go' to resume
    "go" attempts to reboot, but I end up back in the same place.
    Please help.
    Thanks in advanced,
    Craig

    It seems like the driver for that device does not exist. Since the system installed successfully it means that it S10 did find a disk. I wonder if that was a different disk than the default disk. Please boot to the miniroot and check the disk info.

  • After update, Itunes can't load. I get error message R6034, attempt to load the C runtime library incorrectly. I have repeatedly removed and reinstalled Itunes and still have the same problem!!!

    After update, Itunes can't load. I get error message R6034, attempt to load the C runtime library incorrectly.
    I also get error code 7 (Windows error 1114), saying itunes wasn't installed correctly. It appears that I am not the only one with this issue. what is wrong with the latest update?? I tried removing Itunes and all of its components and installing it again, but get same errors and i have also tried doing a system restore with the same results

    Doublechecking. Have you also tried the following user tip?
    Troubleshooting issues with iTunes for Windows updates

  • IPhoto: After I've changed the file name/format in Finder iPhoto can't load/relink to the referenced file.

    After I've changed the file name/format in Finder iPhoto can't load/relink to the referenced file anymore. For some reasons I don't like to reimport the file.

    Hmm the advice has been not to use referenced libraries - you ignored and did it anyway and you find the advise not helpful
    Furthermore the advice is that if you choose to use a referenced library that you assure that the path never changes - you also choose to ignore that advice and do it anyway - and you blame the peopson trying to help you
    once again - you have one choice - change the file names back and put the files back in the exact same place - and again you are totally ignoring the advice and instead name calling and attacking the person giving you advice
    Maybe life would be easier if you followed advice rather than ignoring it and then complaining that things no longer work
    change the name back and you will be fine until the next problem you hit that is caused by choosing a referenced library
    Have a nice day
    LN

  • Can't load line6usb driver module after installing from AUR

    I downloaded the line6usb package from the AUR. After building then installing with pacman I should be able to load the module ala modprobe line6usb, but I get the error:
    FATAL: MOdule line6usb not found.
    I looked for the module itself and found it here(assuming this is it):
    /lib/modules/2.6.27-ARCH/extra/line6usb.ko
    Does anyone have an idea why I can't load this module? I'm still quite the noob with concerning things like this and I'm assuming it's something obvious I need to do.

    I downloaded the line6usb package from the AUR. After building then installing with pacman I should be able to load the module ala modprobe line6usb, but I get the error:
    FATAL: MOdule line6usb not found.
    I looked for the module itself and found it here(assuming this is it):
    /lib/modules/2.6.27-ARCH/extra/line6usb.ko
    Does anyone have an idea why I can't load this module? I'm still quite the noob with concerning things like this and I'm assuming it's something obvious I need to do.

  • Can't load previously installed Acrobat 9 Pro after my CS6 trial expired.

    Can't load previously installed Acrobat 9 Pro after my CS6 trial expired. Keeps asking to buy the trial version or license the software (in reference to the CS6 trial, even though I'm loading my own Acrobat 9 Pro from my CS4 Creative Suite I purchased and had previously installed--still installed to my knowledge...at least I never uninstalled it anyway, if that helps)
    Thank you!

    Yes. I have tried to repair it, but it still didn't work. I had to completely uninstall - reboot - then do a clean install. Works beautifully for a few weeks, then nothing.

Maybe you are looking for