Can't log into router setup page

I updated my firmware today on a WRT54GL router. Upgrade was successful but when I clicked to continue I got a message that access was denied.  I have tried to log in with the address 192.168.1.1 and get the same message. Any help?

After a firmware upgrade, you must reset the router to factory defaults (see note below), then setup the router again from scratch.  If you saved a router configuration file, DO NOT use it.  If you have not done this since the last firmware upgrade, please do it now and see if that corrects your problem.
If you still have trouble viewing your router setup pages, do the following:
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Check to see if your "modem-router" is using the same 192.168.1.x address space as your Linksys router. If it is, then report back with this problem, and also state the make and model of your modem-router.
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If you still have problems, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
Note:  To reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
Message Edited by toomanydonuts on 01-06-2008 08:04 PM

Similar Messages

  • Can't connect to router setup page

    Hi,
    I have a WRT54G wireless router, version 2.1. It's been working fine for the last 3 years and suddenly the WLAN light is out and there's no communication between router & computer. I've tried resetting it (via reset button, and unplugging power) a million times with no results. A techie thought maybe I needed a firmware upgrade -- which I've downloaded, but now I still have to access the setup page to install it, which seems to be impossible. The 192.168.1.1 page won't come up at all. (And when I went into the command prompt, it said my Default Gateway was 207.237.223.1 -- which, of course, I've tried, but that won't come up either.) I've turned off firewalls and antivirus programs, thinking they might be the problem -- still nothing. Any suggestions/advice would be MUCH appreciated! Thanks in advance!
    TrevorNYC

    You need to try again to reset the router to factory defaults.
    To reset your router to factory defaults, use the following procedure:
    1) Power down all computers, the router, and the modem, and unplug them from the wall.
    2) Disconnect all wires from the router.
    3) Power up the router and allow it to fully boot (1-2 minutes).
    4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5) Power down the router.
    6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7) Power up the router and allow it to fully boot (1-2 minutes).
    8) Power up the computer (if the computer has a wireless card, make sure it is off).
    9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
    10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
    If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
    Please let me know how things turn out for you.

  • Can't log into router because of connect cloud

    How do I get past this slow connect cloud b.s.?  Now it's stopping me from logging into my router all together.  I keep getting a message "we've encountered an unexpected error" blah blah blah.  I can't get past it.  I've already rebooted my router.

    *Sigh*  I really don't want to be on the phone foreever just to end up with something like "you have to reset your router to factory settings".  I don't have time for that.  People in my office need me to change (verify) a password to the guest network.  It shouldn't be this difficult.
    I was able to connect to the cloud thing yesterday.  Nothing changed since then.  Why can't I connect now?  I'm guessing it's a cloud website issue and it'll clear up soon.  I just want to go back to original firmware now.  This cloud thing doesn't give me anything new or better.....only slower and now, nothing at all.

  • Can't log into set up page

    i am new to this forum and have searched somewhat but can't find an answer to my dilemma.  i tried to go into 192.168.1.1 but the log in screen asked for a name and password.  someplace i saw that "admin" was the proper response but it didn' work for me; the log in page kept recycling.  any thoughts?? tiafh  bodaceous

    It is possible that you have changed it to something else already. Try to enter a password that you might have changed it to or use admin in both fields. If ever nothing works then reset is the next step. When you reset though, everything will go back to defaults so you have to reconfigure the router again for wired and wireless internet connection.

  • Unable to enter router setup page

    my router is WRT54G..i can only enter into the setup page once..after i close my IE..i am unable to enter anymore..must do a reset to enter again..is my router faulty ? plsssss help

    well.....possibly a firmware issue...follow the steps :
    1)go to ftp.linksys.com/pub/network and download the tftp.exe file....
    2)go to www.linksys.com/download and download the latest firmware for the corresponding version no. of WRT54G ...
    3)run the tftp.exe file
    4)here, the server is router's ip add ( 192.168.1.1 ) , password is router's password ( by default it's "admin" ) and browse the firmware file and click upgrade
    5)once the firmware is upgraded , reset the router and reconfigure it....

  • Changed my 192.168.1.1 to 192.178.1.1 and i can`t log into setup in WRT54G v5 via navigato

    changed my 192.168.1.1 to 192.178.1.1 and i can`t log into setup in WRT54G v5 via browser
    How can i reset the router to initial manufacturer`s state?

    At back panel of router u have a reset button ........... keep it pressed for 30 sec...... unplug & plug power to router ........... it will set to default 192.168.1.1....
    Tell me if it works or not.........

  • Can't log into PowerShell and EAC on Exchange 2013 Server

    I'm not sure why but I my Exchange PowerShell can't log into my Exchange server and I can't access the EAC
    via localhost or the URL. 
    I did notice that I enabled HTTP Proxy in IIS and that I used Application Route Requesting with it but I went ahead
    and reversed all those changes. I also noticed that the physical path for each sub-site in Default Web Site goes to the HTTP Proxy version of that folder instead of the ClientAccess one. I changed each folder to the clientaccess one but that didn't help. I
    did some research on this and I saw that I had to enable the kerbauth in the modules area and I did that to. I restarted IIS and WebRM and that still didn't help. 
    The Exchange Management Shell error: 
    New-PSSession : [exchangeserver.domain.net] Connecting to remote server exchangeserver.domain.net failed with the
    following 
    error message : The client cannot connect to the destination specified in the request. Verify that the service
    on the 
    destination is running and is accepting requests. Consult the logs and documentation for the WS-Management service 
    running on the destination, most commonly IIS or WinRM. If the destination is the WinRM service, run the following 
    command on the destination to analyze and configure the WinRM service: "winrm quickconfig". For more
    information, see 
    the about_Remote_Troubleshooting Help topic. 
    At line:1 char:1 
    + New-PSSession -ConnectionURI "$connectionUri" -ConfigurationName Microsoft.Excha ... 
    + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo : OpenError: (System.Manageme....RemoteRunspace:RemoteRunspace) [New-PSSession], PSRemotin 
    gTransportException 
    + FullyQualifiedErrorId : CannotConnect,PSSessionOpenFailed 
    On the web when I try to access EAC on our URL and not localhost, I get this error: 
    400 
    Bad Request :( 
    The request sent by your browser was not valid 
    On localhost, I just get a page cannot be found.

    Hello
    tip:
    Check Get-owavirtualdirectory | fl and Get-ECPVirtualDirectory | fl and make sure that you using “Form based Authentication” and “Basic Authentication”
    and check Control Panel\All Control Panel Items\Credential Manager for saved password.
    and http://goo.gl/IC5P4S
    sorry my english

  • HT204347 I can't log into my icloud account

    I can't log into my icloud account from my MacBook Pro, I keeps taking me to set-up window, I've been using it for years, I running 10.7.5, it's turned on, can't get on with my iphone either also takes me to the setup window. Also can get support as there help page won't recognize my serial number even when copy/pasted?

    Hi
    https://appleid.apple.com/
    and
    https://www.icloud.com
    are two different accounts
    Therefore you should still use your "old" (existing) iCloud mail address - you cannot change the iCloud mail address.
    However you could add an alias instead to you iCloud account.
    http://support.apple.com/kb/PH2622?viewlocale=en_US&locale=en_US

  • I can't log into my iTunes account. I logger out a few days ago to trouble shoot because I was trying to redeem some iTunes cards but when i pressed redeem nothing happened. Now when i press sign in and then choose existing Apple ID, nothing happens

    I can't log into my iTunes account on my iPhone 5s. I logged out a few days ago to trouble shoot because I was trying to redeem some iTunes cards but when i pressed redeem nothing happened. I then tried to log back in immediately afterwards. I was unable to do so. After clicking "sign in" at the bottom of the apps main page, it brought up another menu where I clicked "Choose existing Apple ID". After pressing this the menu disappeared and nothing happened. I tried this multiple times and received the same result each time. I tried the other available option of creating a new AP ID to log in with and that one worked perfectly fine. I am clueless as to why the log in for me is either not able to load or just completely blocking me from getting back into my iTunes account on my phone. Not only can I not listen to the music I currently have, but I cannot log in to purchase the new music that I wanted to with my unused iTunes gift cards

    I have the same problem too and tried alot of things like time zone , restarting or changing DNS of wifi connection to 8.8.8.8 still nothing happens .. !!
    iPhone 5s, iOS 8.3

  • Since I can not log in bug report page, not even getting an error message, I'll write all my issues with ios8 here...

    Since I can not log in bug report page, not even getting an error message, I'll write all my issues with ios8 here... I have an iphone 4S and I did the last update. Now I am in trouble.
    1. When I move the "sound on/off" button, I get it buzzing 10 times before the setting is changed and I can do anything else, just not reacting to the round button on screen touches.
    2. Impossible to copy text from most websites into notes.
    3. Impossible to delete an email account in settings.
    4. Uses up the battery twice as fast as before. I have "update apps" setting turned off, just reading a couple of mails, making a couple of photos and open maps apps twice a day, and the battery is dead well before the evening.
    5. Got extremely slow, and it was getting slower and slower with every system update.
    I'm sure I forgot something... But well, that already a lot.

    Well, actually number 3 in my list is not true any more, I just tried to delete my account 15 times, then I've written my post, then half an hour later my Settings finally updated my accounts list. Whohoo
    I did not try restoring it yet, thank you for the link!

  • I changed my Apple ID password and now I can't log into iCloud

    I changed my Apple ID password and now I can't log into iCloud.  In addition I am unable to sign out or exit the iCloud System Preference page and have to force a shut down using the power off button to get rid of it.  Does anyone know how to fix this? Thanks

    If the Preference Pane hangs, hit comand-option-escape and force quit System Preferences to avoid having to reboot.
    In order to sign out you need the original password if you have set up 'Find My ....'. However you can't now change the password back to the original one (as you are not allowed to re-use a password).In this situation only Support can help you.
    To contact  iCloud Support: if you currently happen to have AppleCare, either because you recently bought Apple hardware or have paid to extend the inititial period, you can contact them here:
    http://www.apple.com/support/icloud/contact/
    You will need the serial number of the covered hardware.
    If you are not covered by AppleCare, then - in common with other free email services - there is no free support and you may be asked to pay a fee.

  • WRT54GS router setup page won't display most text

    So I bought a new Linksys WRT54GS v6 wireless router yesterday, and I was able to set it up to share my DSL line, but when I went to the router setup page (192.168.1.1), it wouldn't display most text. It displays text in the entry boxes, but there are no links or other text on the page. I took a screenshot which can be seen here: http://img87.imageshack.us/img87/3390/routersetuppagemc1.jpg
    Does anyone know what I can do to solve this issue?

    Hey Merugo. I was having the same problem with the router settings screen refusing to load for my WRT54G. Do you happen to have v.5 of the router? After digging around in the help files on the site, I found this for firmware recovery for the WRT54G v.5 and it fixed the problem I was having once it loaded the updated .bin. Blank screen be gone.
    http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=3176
    (The first time the router tried to load the new .bin it timed out. And the second time it installed correctly though it didn't display "Upgrade Success" like it's apparently supposed to.)
    Hope this can maybe help you since it fixed things for me.Message Edited by Res on 10-03-200606:44 PM

  • I can't log into itunes.  I first established my account on a Macbook, but now I am on a PC.  I downloaded the software for a PC, but I still can't log in.

    I can't log into itunes.  I first established my account on a Macbook but am now using a PC (Dell XP).  Can you help me?

    HI,
    The Apple IDs from @mac.com and @me.com (Older MobileMe and more recent iCloud Names) are also Valid AIM Screen names.
    Any other sort of Apple ID is not a Valid AIM Name.
    A Google ID that is associated with Google Mail Account (And has "Talk" enable on your Google Settings) can be used in iChat as  Jabber Name/ID.  (Google Run  Jabber server).
    Jabber and AIM are different IM Services and it is not easy or straight forward to add Buddies from one Service to the Buddy List of another.  (As A Starting point consider it "impossible")
    iChat 4 and 5 have links to the registration page of @Mac.com here with a "Get an iChat Account" button in the add (Account) screen  (You select @mac.com or MobileMe and then press the Button - Choosing AIM and then pressing the button used to lead to the AIM registration page but AIM moved their page).
    Apple IDs can be any valid email (or an @mac.com or iCloud registration)
    Therefore you could make a Google ID into an Apple ID.
    However this will not be a valid AIM Screen Name the way @mac.com or MobileMe/iCloud ones are.
    Valid AIM Screen Names in Table (pic)
    7:46 PM      Monday; December 5, 2011
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
      iMac 2.5Ghz 5i 2011 (Lion 10.7.2)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
    "Limit the Logs to the Bits above Binary Images."  No, Seriously

  • HT4436 my mom lost her ipad. can I log into her icloud account on my iphone 5

    My mom has lost her Ipad.  Can I log into her icloud account from my iphone 5?

    What To Do If Your iDevice Is Lost Or Stolen
    What you cannot do is track your device using a serial number or other identifying number. You cannot expect Apple or anyone else to find your device for you. You cannot recover your loss unless you insure your device for such loss. It is not covered by your warranty.
    If your iPhone, iPod, iPod Touch, or iPad is lost or stolen what do you do? There are things you should have done in advance - before you lost it or it was stolen - and some things to do after the fact. Here are some suggestions:
    This link, Re: Help! I misplaced / lost my iPhone 5 today morning in delta Chelsea hotel downtown an I am not able to track it. Please help!, has some good advice regarding your options when your iDevice is lost or stolen.
      1. Reporting a lost or stolen Apple product
      2. Find my lost iPod Touch
      3. AT&T. Sprint, and Verizon can block stolen phones/tablets
      4. What-To-Do-When-Iphone-Is-Stolen
      5. What to do if your iOS device is lost or stolen
      6. 6 Ways to Track and Recover Your Lost/Stolen iPhone
      7. Find My iPhone
      8. Report Stolen iPad | Stolen Lost Found Online
    It pays to be proactive by following the advice on using Find My Phone before you lose your device:
      1. Find My iPhone
      2. Setup your iDevice on iCloud
      3. OS X Lion/Mountain Lion- About Find My Mac
      4. How To Set Up Free Find Your iPhone (Even on Unsupported Devices)

  • I can't log into any of my online accounts after emptying my cache.

    Ever since I reset Safari to empty my cache, history and such, I can not log into any of my online accounts,such as Safari, eBay,etc... I enter my username and password and click the sign in button and the page goes back to the log in page. I don't know what's going on with it.
    Has anyone ever had this problem? If so, please let me know how I can resolve this problem. Thanks!

    Hi
    Welcome to Apple Discussions
    Sounds like you broke the connection between your Password list and Keychain Access. What you may have to do is reestablish those passwords. First step would be to go to keychain access and remove the related entries. Then go back to Safari and access each site. After entering your password information, a prompt ought to appear about keeping the password on file. Select "yes".

Maybe you are looking for