Can't open 192.168.1.1 during setup

I am replacing a Netgear wireless router (WGR614v10) with a Cisco WRVS4400N. When I go to set up the device on my Mac, 192.168.1.1 will not open in a browser. Do I have to do the setup on a PC? Or, am I doing something else wrong?

Hi Jon, first, factory default the unit holding the reset button for 30 seconds. Verifiy on the unit the diagnostic light is not on. Verify the port light is on for the port your computer is connecting to. Open a Terminal and trying to ping the 192.168.1.1. You may also check your network adapter to ensure you're receiving DHCP from the unit. I know on some MAC computer, you have to set your connection preferences. If you've been using wireless, open your network connection and choose your ethernet as primary connection. MAC sometimes does not work using a wireless + ethernet simultaneously.
-Tom
Please rate helpful posts

Similar Messages

Can't open 192.168.1.1 in Windows 8 (WAG200G)

Hi,
I can't open 192.168.1.1 in Windows 8, I've WAG200G
The page just keep loading and nothing happens.
Thanks

Hi,
Try to turn off and turn back on the WAG200G. If still nothing happens, try to use a different browser or different computer.
If everyone needs to believe in something, I believe I'll have another beer..

Cannot open 192.168.1.0 any longer

On Monday, I was able to log in to 192.168.1.0 and changed my password. Today, I can't even open up the page!!!! I have no problem opening other sites but this one will not open. Any suggestions? I am running Windows 2000, IE 6.0. WRTG54GS v.2. Thanks.

Try this...
this might help you:
goodluck!
Yesterday is history. Tomorrow is mystery. Today is a gift.

I can't see my Canon MF4270 printer during setup!

I'm so sick of this printer! I've started school so you could say I'm in the middle of it all so I really need to start printing out papers/documents from my teachers.
I've had this printer for about 3 years now. It's always worked fine with my old laptop running Vista.
I have my iMac in a seperate room and I use my printer (connected to my router) as a network printer.
I went onto the Canon webpage for MF4270 series printers drivers, select my operating system as OSX 10.7 and downloaded the "Mac_UFII_V225_us_ENI.dmg".
I installed the drivers fine.
However after this I go to Settings -> Printings and Fax.
I wait and I wait, but my printer never shows up.
Is there anybody who could help me?

Canon has stated here that they currently have problems printing with the UFR2 v2.25 driver from Preview and TextEdit. The v2.25 driver was released before Lion and is regarded as an intermim solution until an official driver for Lion is released. In the meantime, if you need to print PDFs you can either open them in Safari or download the free Adobe Acrobat Reader X.

Trying to upgrade my wireless routers firmware, but can't access 192.168.1.1 page..

Hey. Im trying to upgrade my wireless router's firmware after I noticed I could not access Nintendos Wifi for the DS. I figured that was the problem since my firmware is out of date I believe. I need some help, but so far nothing has worked trying to access that page.

I'm guessing a lot has changed (to your PC) since you purchased the router. Your other options are:
- empty cookies and temporary internet files, close and reopen IE
- restart both router and PC
- reset the router
- use another PC (preferably with IE6)
Message Edited by neo27 on 01-10-200709:47 AM

Can't see ishuffle on my mac during setup or download songs

I'm trying to set up my child's Christmas present, an ishuffle 2G. Following instruction manual. 3rd step - set up suffle using onscreen instructions when they appear. THEY DIDN'T. So I charged the battery and that's as far as I got. My computer is using Mac OS X v 10.6.8 if that helps.

When you say "2G," does that mean it's the current 4th gen "2GB" shuffle, or that it's the older "2nd gen" shuffle?
If it's the current 4th gen shuffle, you may need to update to the latest version of iTunes. Your Mac OS X version is older, so your version of iTunes may be from before that iPod model was released. The tech specs for the 4th gen shuffle
http://www.apple.com/ipod-shuffle/specs.html
says iTunes "10.7 or later" is required. You can download iTunes here
http://www.apple.com/itunes/
The iTunes System Requirements says "10.6.8 or later," so it should work.

How can I get past the wifi page during setup on iPad 2? I've tried hitting the next button but my screen is cracked and I can't press it

I've tried pressing the next button but my iPad is cracked in that spot.

I'd "get past" that problem by getting a new iPad!

How can I change my 192.168.1.1 settings

Hi I'm on a sim only wifi package. My Device is a Huawei e8278 in car wifi that was purchased unlocked. With my EE card in the dongle I can access the 192.168.11 management page but not all of the options that should be available are. Does EE have its own mobile broadband management software and if so how can I obtain a copy. Thanks for time your help is much appreciated.RegardsMJ

What's missing? All the functionality provided should be already on the device.

Cannot connect to 192.168.1.1

I did a firmware upgrade on the BEFW11S4 yesterday and now I cannot access the web utility. I've tried ipconfig /release and /renew, but to no avail. I've also tried setting a static IP but that did not work as well. I did the firmware upgrade via wireless, and it gave me a success message after it was finished, but the router somehow lagged afterwards, so I did a reset on the utility and it connected. My internet connection is working fine, but I can't ping 192.168.1.1. My ipconfig returns:
Connection-specific DNS Suffix . : nyc.rr.com
IP Address. . . . . . . . . . . . : 24.193.219.59
Subnet Mask . . . . . . . . . . . : 255.255.252.0
Default Gateway . . . . . . . . . : 24.193.216.1
Any ideas? The default gateway should be 192.168.1.1 I've heard, but I have no idea how to set it without being able to communicate with the router.
I also did an IP scan on 192.168.0.* and 192.168.1.* and both returned all IP addresses in that range as dead.
Thanks.

Hey based on your IP check, it seems you are getting an IP address from your modem or from another device. Those IP's that you listed are actually valid IP's but they are not IP's that a private device like a router would give out.

Can't Access Router Settings via 192.168.2.1

I have recently changed modem/routers as my connection speed was increased recently and the old modem wasn't up to the task... The previous modem/router was preconfigured and I did nothing to it, however the new one requires settings be fixed by accessing it via a browser at 192.168.2.1
When the technician came to check my line and set up the new modem, we encountered a strange situation. Despite being connected by Ethernet cable, my machine could not access the IP address reserved for the router.
The reply is: "Safari can’t connect to the server.
Safari can’t open the page “http://192.168.2.1/” because Safari can’t connect to the server “192.168.2.1”."
We tried Firefox and the same happened.
I have deactivated my firewall, rebooted, changed cables, restarted the router, got Safari to pretend to be Explorer, got the neighbor's dog to bark at it, everything except make a blood pact with the devil, and the two browsers on my machine think that 192.168.2.1 is an external address- which it isn't, and of course fails to connect.
The technician used his laptop to configure the thing, so I can access the internet (obviously) but I must find out why I can't access the router/modem's settings, if only to find some logical reason for this illogical behavior.
I've tried looking this issue up, and I get lots of bad wiring, wireless connection, windows proprietary shenanigans, but none that explain my situation.
I'd appreciate it if someone could help me make sense of this.
My setup:
Computer Model Name: Power Mac G4 (AGP graphics)
Model Identifier: PowerMac3,1
Processor Name: PowerPC G4 (3.3)
Processor Speed: 1.35 GHz
Number Of CPUs: 1
L2 Cache (per CPU): 256 KB
L3 Cache (per CPU): 2 MB
Memory: 832 MB
Bus Speed: 100 MHz
Boot ROM Version: 4.2.8f1
Sales Order Number: M7827LL/A
Router: "2-Wire Gateway"

Your advice did the job quite nicely and it seems this is the "natural way of things," but I was totally unaware of it since my previous modems were preconfigured and I never had to muck about with subnets and such things.
What irks me is that this is basic, bare bones information that the Tech support people should have given me right off the bat. Why do they assume I have all the right numbers input into the Ethernet or PPPoE settings? They seemed totally perplexed that I couldn't connect, and frankly so was I- since my old Mac, as decrepit as it is, is still able to kick it with the modern way of things better than most computers I work with.
If they had asked me if I had set the right IP's in the right slots, it could have been fixed in 2 minutes.
Thank you very much for solving my problem, it saves me a lot of stress and confusion.

After update to 33.0a2 don't open https sites in intranet lan (192.168.0.0/24)

I update my FireFox to 33.0a2.
I don't open my intranet https sites -
https://192.168.1.8 reports -
===============================
Сервер не найден
Firefox не может найти сервер 192.168.1.8.
Проверьте, не допущена ли ошибка при наборе адреса, например, ww.example.com вместо www.example.com
Если ни одна страница не загружается – проверьте настройки соединения с Интернетом.
Если компьютер или сеть защищены межсетевым экраном или прокси-сервером – убедитесь, что Aurora разрешён выход в Интернет.
==================================
But in 32.0a2 Working - Ok

Actually this is the Aurora development channel as Nightly currently has 34.0a1 active on it. Note that both Aurora and Nightly channels gets checkins almost everyday so therefore they get a update each of those days which can sometimes have regressions or issues that may get fixed or reverted the next day.

Can't connect to 192.168.1.1 with WRT610N

Hi, i've been trying to add my sister's new laptop to the authorized MAC adress on the router, but i just can't get on the 192.168.1.1 administration page. When i type the adress in, the page loads for minutes, hours and even days with no result. I tired on the four computers connected to the routers but the page just loads forever and never shows.

Hi, I think I finally found the problems with not getting access to 192.168.1.1, or at least it works on my computer for now. Haven't tried it more than today, but I think this is the problem.
Turn of Linksys advisor program. Then try 192.168.1.1 It worked on my computer. The Linksys advisor loads on startup, and I think I will have the same problem again, if it starts up, so I will try to disable it in startup. I've also configured the network settings on the connection to internet protocol version 4 (TCP/IPv4) to use the following IP address of my computer (192.168.1.X), subnett 255.255.255.0 and default gateway to 192.168.1.1. Without those setting, ie obtain IP address automatically, I couldn't reach 192.168.1.1 You can manually start the Linksys advisor program afterwards, and I had no problems connecting to 192.168.1.1
I have tried every other solution mentioned on this forum, but nothing has worked for me. The most commoned answer is, reset your router or turn off the router, then it will work again. It does, but only for a day, or sometimes minutes, then its back to the same problem, with not being able to connect to 192.168.1.1 I have also downgraded the firmware and are using open DNS, but that didn't help. It seems to me that the problem is with the Linksys advisor program, kind of strange that I have read only one post mentioning that! But of course, I'm not 100% sure, but again, its working on my computer, and I can finally connect to the administration pages again!

Problem with my linksys WRT120N i can't connect to the address 192.168.1.1

Hello friends
i need help cuz i can't connect to the address 192.168.1.1
i didn't change the address 192.168.1.1 to an other address but i can't connect to this last i want to change my options
i really need help plz

Make sure that the computer is connected to the router on the Ethernet port..Now,check the ip address on the computer....Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...
If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security softwares on the computer...
If you get 4 replies then,Adjust the Browser Settings on the computer....Open an IE, click Tools >> Internet Options, then delete all files, cookies, history, forms...Goto "Connections", make sure Never Dial a Connection is checked, click on LAN Settings and make sure all the options are unchecked...Once you are done click on O.k...Close the IE and re-open it...

Copy startup-config tftp + %Error opening tftp://192.168.0.12/router-confg (Socket error)

Please advise me on the below error;; I am using tftpd for tft
Router#copy startup-config tftp
Address or name of remote host []? 192.168.0.12
Destination filename [router-confg]?
%Error opening tftp://192.168.0.12/router-confg (Socket error)

This was the right answer.. Solved
https://learningnetwork.cisco.com/thread/56041
im surprised you can ping without attaching a crossover cable.
because if your only using your console port to connect your pc...then you dont have ip connectivity
i think the cable your using to connect your pc to your router fa port is a straight through ethernet cable....
you see it attaches to a switch port in the back of your home router(not cisco router)
not a router port.
so you need a different cable depending on how you want to connect to your router.
you can check to see if it is a crossover cable
just peer down the end of the cable you can see the colours...
if they are in the same order on each end...then it is a straight through cable
if they have a different order...then it is a crossover cable
if your connecting to your pc via your home router.
then yes.....you need to plug a straight through cable into your cisco router from your home router
and it will work
if your connecting your pc directly to your router
then you need to use a crossover cable from the back of your pc...to your cisco router.
and it will work

192.168.1.1 will not open. Have tried repeatedly. Please help!!

Hi, Two days ago I was able to type this in my browzer (Safari, Macintosh) and open the page. Now for two days I have tried this again and get a massage that the server at this location (192.168.1.1 ) is not responding. How can I get onto this page. I need to change the settings on my WRT54G V8. Any help would be appreciated.
Thanks, Bill

Sorry to hijack your thread but my issue is very similar and driving me nuts!
For some reason my wireless network at home started playing up. I thought I'd do some quick fixes....not so quick.
Original set-up was AM300 DSL modem (192.168.1.1) with desktop pc cabled into port 1 of WRT610N (10.10.10.1). I used to be able to access both ip numbers to get into menus.
After trying to troubleshoot an issue with my mrs wifi connection, I am now unable to access 10.10.10.1 via port 1 on WRT610N direct to my PC's LAN port (I have 2 LAN ports on PC and no luck with either). If I plug into my laptop and not the desktop, no issue accessing 10.10.10.1 (router).
I have pinged 192.168.1.1 as suggested above and get 0% loss on laptop but when plugged into desktop I get 'geenral failure' and 100% loss.
I'm no expert at PC's but was able to build the desktop I had and had it running for a year without issue. So why are my LAN ports on my desktop giving me grief? And it always appears to be showing as a 'public netwrok' on my desktop when in 'network and sharing center'. I change it to private (as it sound like the right thing) but ends up as an 'unidentified network' (or similar).
I assume more detail is better than too little? Thx for reading.
Any help appreciated.

Can't open 192.168.1.1 during setup

Similar Messages

Maybe you are looking for