Can't Open ports in Express

Hi,
Here's my setup:
Cable router connected by ethernet to Airport Extreme (not the new model)
Airport extreme broadcasts to an Airport Express which relays the signal to my computer.
I need to open up my ports for Transmission to use so I can get my upload ratio up. I always remain in stealth mode whenever I connect.
I've gone into my system prefs and allowed transmission to use ports in 10.5 (different setup in leopard now)
I've also opened up the ports needed for the Extreme, but when I get to the Express there doesn't seem to be any options for opening ports, so I remain in stealth mode with terrible upload speeds.
All help is greatly appreciated.

The reason you don't see any options for opening ports on your Airport Express is because it isn't relevant to its current mode of operation. Your Airport Express has been configured as a remote base station - as you said, it relays signals from your base station to your computer. In that mode, the Airport Express's built in router is completely disabled - and since it is completely disabled, there is no need to be forwarding ports.
You mentioned you have a "cable router". If this "cable router" indeed has a built in router, then your efforts need to be directed to either turning off its router (to work in so-called "bridge mode") or setting up port forwarding on that device.

Similar Messages

How can I open ports on my AirPort Extreme, from WINDOWS?

I have an Airport Extreme as my router, and I have a Windows-based computer. I need to open ports on the router (ironically, it is for my Apple TV).
However, even though I can use the Airport Utility for Windows (latest version 5.5.3), I cannot open ports from the application.
Everywhere I look, I am supposed to have a firewall tab in the Advanced section, but I do not have it. The only tabs that I have in Advanced are:
Logging and Statistics
MobileMe
IPv6
How can I open ports on my Airport Extreme router from Windows?

Is your AirPort Extreme the only router in your network configuration?

Can't open port 80

I just can't open port 80 on my AEBS n 1st G. I want to use this port to enable access from the internet to my Mini server's wiki pages.
I've added port 80 in the "Port Mapping" tab of Airport utility under "personal web sharing", but when I check the port with the network utility, it remains closed.
What am I doing wrong. Please help.
This is the data of the mapping tab in Airport utility:
Public TCP port: 80
private IP address:10.0.1.201
Private TCP port: 80
rest empty.

Sorry for not replying sooner, I was out of town.
I did the setup as you showed it, tested it and it still doesn't work.
I also contacted my ISP with some questions about the port 80 being open or not. Their answer is that port 80 is always open as that's the port used to access the internet (made me feel like my question was reeeaaaally stupid...). I explained I had found some info on the internet that said the Zyxel modems very often come with the port 80 closed, and that nearly made them laugh... :-(
So I once again did a scan of my public port and get this:
Port Scanning host: 200.124.48.xxx
Open TCP Port: 21     ftp
Open TCP Port: 53     domain
Open TCP Port: 554    rtsp
Open TCP Port: 3900   udt_os
Open TCP Port: 5009   winfs
No port 80 in view.
I also did a traceroute of the Dyndn'ssed domain I want to access on my server and get this:
traceroute to http://korkettes.com/groups/essai/calendar/ (67.215.65.132), 64 hops max, 72 byte packets
1 10.0.1.1 (10.0.1.1) 14.436 ms 12.512 ms 8.778 ms
2 10.9.88.1 (10.9.88.1) 24.442 ms 12.056 ms 10.001 ms
3 sblx12gw.gtdinternet.com (190.196.63.126) 18.751 ms 10.161 ms 10.517 ms
4 cn1.ge1-0-1.sblx12.gtdinternet.com (190.196.125.54) 38.874 ms 144.407 ms 12.339 ms
5 ci1.te1-2.v219.cn1.gtdinternet.com (190.196.125.29) 11.119 ms 25.334 ms 25.875 ms
6 tengigabitethernet9-3.ar3.scl1.gblx.net (64.209.88.25) 50.010 ms 8.308 ms 8.641 ms
7 ae3-30g.scr3.nyc1.gblx.net (67.17.104.189) 185.237 ms
    ae0-30g.scr4.nyc1.gblx.net (67.16.139.2) 212.148 ms 248.437 ms
8 e5-1-30g.ar9.nyc1.gblx.net (67.16.142.54) 149.660 ms 147.576 ms 139.618 ms
9 xe-0-3-0-6.r05.nycmny01.us.bb.gin.ntt.net (129.250.8.129) 146.279 ms 200.869 ms 136.877 ms
10 ae-1.r23.nycmny01.us.bb.gin.ntt.net (129.250.4.68) 144.528 ms 262.677 ms 209.261 ms
11 ae-1.r20.asbnva02.us.bb.gin.ntt.net (129.250.2.9) 173.034 ms 390.095 ms 181.918 ms
12 ae-1.r01.asbnva02.us.bb.gin.ntt.net (129.250.3.11) 424.923 ms 233.061 ms 439.628 ms
13 ge-0-7-0-33.r01.asbnva02.us.ce.gin.ntt.net (129.250.12.114) 286.701 ms 138.696 ms 131.210 ms
14 hit-nxdomain.opendns.com (67.215.65.132) 128.300 ms 135.859 ms 136.805 ms
Just so you know: GTD is my ISP.
I can access the same domain locally with miniserver.local/groups/essai/calendar/ very well.
don't know what else to try.

Can I open Final Cut Express HD project in FCP????

Can I open Final Cut Express HD project in Final Cut Pro?

This appears to be a duplicate post. Responses should go here
x

Since connecting my new Cinema display, I can't open Final Cut Express because I don says Quartz extreme, Since connecting my new Cinema display, I can't open Final Cut Express because I don says Quartz extreme

Since connecting my new Cinema display to my new Mac Pro, I can't open Final Cut Express. I get the message that I need Quartz Extreme to use it. How come it isn't in my brand new computer or monitor?? I could use FCE fine with an old monitor. HELP!

I finally called Apple support on Monday (couldn't on Sunday - it surprised me that they don't have 24/7 phone support). Tech had no idea, so put me onto a 'supertech' (in America?). He instructed me to reset the whole computer - turn it off, unplug it and then hold down 4 keys while it rebooted. That worked. I can now open Final Cut Express and iMovie. There's no reference to 'Quartz Extreme' in my 'About This Mac' display info, but I don't care, everything works now, hooray! (Now if I can only get my Mac mouse to work properly...)

HT5103 How can I open Final Cut Express project in Final Cut Pro X?

How can I open Final Cut Express project in Final Cut Pro X?

If you export the project from FCE you can import the QuickTime into FCP. You can do limited work to it like adding titles.

How can I open port 80

I am using a 2wire modem/router. I was told by a tech at ATT that I can only click a button that allows ALL ports open, but not just port 80.
Does anyone know if there is a way to open port 80 ONLY? I'm next to done setting up a security CCTV system for my home, and this would allow me to use my computer to look at whats going on, rather than buying a new monitor.
Thanks for helping.

Thanks for the reply. You and X423424X are close. From the beginning. I bought a 4 camera DVR security surveillance system. Yesterday, we installed it. I was told by the place from which I bought it ( and subsequently from the manufacturer's tech guy) that if I wanted to use my computer for a monitor for the security setup, that in the Router Firewall Settings I would have to identify the device, and then 'direct' the device "through" port 80 to be able to view the 'goings on outside' (the input from the cameras) from my computer monitor. Inclusive with this configuration via the iMac, is that the DVR is recording all the time, and I could download any portion of the recorded material from the DVR to the iMac and burn it to a disk, for example to give to the cops if there was a theft. AND, it was also mentioned that in order to remote view whats going on around the place from say, a laptop or pc when I'm out of town can also be done, but that would require opening another port, with 4 digits, like 3806, or similar. I will eventually get the port number for this operation later. So that is what I'm trying to do.
So far, the 'local tech' from the security store seems to have limited knowledge of the Mac, and of the 2Wire router/modem. So HE was on the phone with first the tech support from the security cam/DVR dealers, and then with an ATT tech. The ATT tech was the one that said, in the firewall settings on the modem, there is a button that opens ALL ports, and that was the only way to allow port 80 to be used for the DVR/security setup.
I think that he is incorrect. I think that there is a way to view the camera images on my Mac monitor, and that there is a way to configure the settings on the router to allow the camera images to be seen on the computer screen, and that I could also download to the HD on the iMac any 3 or 4 minute portion of what is recorded on the DVR, in order to burn a copy. I have a co-worker that had a car taken, and her neighbor was there in an instant telling her thatt he had the whole thing on his video surveillance, and had a disc burnt in about 5 minutes, which went to the police. Her car was found, and the perp arrested within 2 hours.
THATS what I want to end up with (no, not a stolen car, but the configuration), and I'm hoping that I can find the way to get 'er done here. There is only one good Apple/OS X tech in this town, and he is on vacation for another week. AND, I'm not sure he is a 2wire expert.
So, again, thank you for any help or input.

Can't Open Final Cut Express

I deleted a Final Cut Express project and emptied trash. Now can't open FCE. Message "one/more scratch disks does not have read/write access.

Use Disk Utility to repair permissions. Get Info for your drives and make sure the read/write permissiins are set correctly.

Can't open ports on BT home hub 2

Hello I can't open these ports on my BT home hub 2
27000-27015 as UDP
27016-27030 as UDP
27014-27050 as TCP
4380-4380 as UDP

Please see this guide.
Port forwarding problems
If you are trying to forward them all to the same device, then you have overlapping ports and it will not work.
You are trying
27000-27015 as UDP
27016-27030 as UDP
27014-27050 as TCP
4380-4380 as UDP
Try instead
27000-27050 UDP
27000-27050 TCP
4380-4380 UDP
That includes the full range. It does not matter if you forward both TCP and UDP.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

I have flash media server but how can i open port 1935

how would i open
Port 1935 on my server as i think this is why my streaming in flash med
ia server does not work

This is my port details from command prompt Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:\Users\Administrator>netstat Active Connections Proto Local Address Foreign Address State TCP 127.0.0.1:11110 WIN-L969VFMO5GO:49242 ESTABLISHED TCP 127.0.0.1:19350 WIN-L969VFMO5GO:49167 ESTABLISHED TCP 127.0.0.1:19350 WIN-L969VFMO5GO:49243 ESTABLISHED TCP 127.0.0.1:49167 WIN-L969VFMO5GO:19350 ESTABLISHED TCP 127.0.0.1:49242 WIN-L969VFMO5GO:11110 ESTABLISHED TCP 127.0.0.1:49243 WIN-L969VFMO5GO:19350 ESTABLISHED TCP 192.168.1.65:1111 WIN-L969VFMO5GO:50394 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50371 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50393 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50395 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50398 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:51012 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:51091 ESTABLISHED TCP 192.168.1.65:49230 a92-123-153-19:http CLOSE_WAIT TCP 192.168.1.65:49231 a92-123-153-83:http CLOSE_WAIT TCP 192.168.1.65:50371 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:50393 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:50394 WIN-L969VFMO5GO:1111 ESTABLISHED TCP 192.168.1.65:50395 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:50396 192.150.8.200:https CLOSE_WAIT TCP 192.168.1.65:50398 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:51012 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:51091 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:51412 text:http TIME_WAIT TCP 192.168.1.65:51413 text:http TIME_WAIT TCP 192.168.1.65:51416 bits:http TIME_WAIT TCP 192.168.1.65:51417 bits:http TIME_WAIT TCP 192.168.1.65:51418 bits:http TIME_WAIT TCP 192.168.1.65:51419 bits:http TIME_WAIT TCP 192.168.1.65:51421 bits:http TIME_WAIT TCP 192.168.1.65:51425 bits:http TIME_WAIT TCP 192.168.1.65:51432 text:http CLOSE_WAIT TCP 192.168.1.65:51433 bits:http TIME_WAIT TCP 192.168.1.65:51438 bits:http TIME_WAIT TCP 192.168.1.65:51439 bits:http TIME_WAIT TCP 192.168.1.65:51444 w2:http ESTABLISHED TCP 192.168.1.65:51445 ww-in-f149:http ESTABLISHED TCP 192.168.1.65:51447 mpr5:http TIME_WAIT TCP 192.168.1.65:51450 wy-in-f144:http ESTABLISHED TCP 192.168.1.65:51451 ir1:http ESTABLISHED TCP 192.168.1.65:51452 mpr6:http TIME_WAIT TCP 192.168.1.65:51453 ir1:http ESTABLISHED TCP [fe80::7800:6e:735:c444%13]:3389 pc-PC:49161 ESTABLISHED C:\Users\Administrator>ping 192.168.1.65 Pinging 192.168.1.65 with 32 bytes of data: Reply from 192.168.1.65: bytes=32 time<1ms TTL=128 Reply from 192.168.1.65: bytes=32 time<1ms TTL=128 Reply from 192.168.1.65: bytes=32 time<1ms TTL=128 Reply from 192.168.1.65: bytes=32 time<1ms TTL=128 Ping statistics for 192.168.1.65: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\Users\Administrator>netstat -a Active Connections Proto Local Address Foreign Address State TCP 0.0.0.0:80 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:135 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:445 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:1111 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:1935 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:3389 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:6515 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:8134 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:47001 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49152 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49153 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49154 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49155 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49163 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49164 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:9421 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:9422 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:9423 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:11110 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:11110 WIN-L969VFMO5GO:49242 ESTABLISHED TCP 127.0.0.1:19350 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:19350 WIN-L969VFMO5GO:49167 ESTABLISHED TCP 127.0.0.1:19350 WIN-L969VFMO5GO:49243 ESTABLISHED TCP 127.0.0.1:49167 WIN-L969VFMO5GO:19350 ESTABLISHED TCP 127.0.0.1:49242 WIN-L969VFMO5GO:11110 ESTABLISHED TCP 127.0.0.1:49243 WIN-L969VFMO5GO:19350 ESTABLISHED TCP 169.254.196.68:139 WIN-L969VFMO5GO:0 LISTENING TCP 192.168.1.65:139 WIN-L969VFMO5GO:0 LISTENING TCP 192.168.1.65:1111 WIN-L969VFMO5GO:50394 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50371 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50393 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50398 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:51012 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:52277 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:52388 ESTABLISHED TCP 192.168.1.65:49165 WIN-L969VFMO5GO:0 LISTENING TCP 192.168.1.65:50371 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:50393 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:50394 WIN-L969VFMO5GO:1111 ESTABLISHED TCP 192.168.1.65:50396 192.150.8.200:https CLOSE_WAIT TCP 192.168.1.65:50398 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:51012 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:52277 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:52319 a92-123-153-19:http CLOSE_WAIT TCP 192.168.1.65:52388 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:52592 wy-in-f157:http ESTABLISHED TCP 192.168.1.65:52593 wy-in-f157:http ESTABLISHED TCP 192.168.1.65:52612 ww-in-f155:http ESTABLISHED TCP 192.168.1.65:52619 ww-in-f102:http ESTABLISHED TCP 192.168.1.65:52620 a92-123-153-25:http ESTABLISHED TCP 192.168.1.65:52626 a92-123-153-81:http ESTABLISHED TCP 192.168.1.65:52717 fe:http TIME_WAIT TCP 192.168.1.65:52720 91.103.142.194:http ESTABLISHED TCP 192.168.1.65:52722 a92-123-153-10:http ESTABLISHED TCP 192.168.1.65:52724 a92-123-153-10:http ESTABLISHED TCP 192.168.1.65:52725 a92-123-153-10:http ESTABLISHED TCP 192.168.1.65:52726 a92-123-153-10:http ESTABLISHED TCP 192.168.1.65:52729 65.242.27.32:http TIME_WAIT TCP 192.168.1.65:52730 65.242.27.32:http TIME_WAIT TCP 192.168.1.65:52732 ww-in-f102:http ESTABLISHED TCP 192.168.1.65:52734 64.236.76.160:http ESTABLISHED TCP 192.168.1.65:52739 ec2-79-125-122-81:http ESTABLISHED TCP 192.168.1.65:52740 95.101.16.74:http ESTABLISHED TCP 192.168.1.65:52741 mpr2:http TIME_WAIT TCP 192.168.1.65:52742 ec2-79-125-28-85:http TIME_WAIT TCP 192.168.1.65:52744 a92-123-153-9:http ESTABLISHED TCP 192.168.1.65:52745 mpr2:http TIME_WAIT TCP 192.168.1.65:52746 wy-in-f156:http ESTABLISHED TCP 192.168.1.65:52747 a92-123-153-82:http ESTABLISHED TCP 192.168.1.65:52749 64:http TIME_WAIT TCP 192.168.1.65:52757 64:http TIME_WAIT TCP 192.168.1.65:52760 mpr2:http TIME_WAIT TCP 192.168.1.65:52761 ec2-79-125-28-85:http TIME_WAIT TCP 192.168.1.65:52763 mpr2:http TIME_WAIT TCP 192.168.1.65:52764 64:http TIME_WAIT TCP 192.168.1.65:52770 194.129.79.23:http TIME_WAIT TCP 192.168.1.65:52774 mpr2:http TIME_WAIT TCP 192.168.1.65:52776 mpr2:http TIME_WAIT TCP 192.168.1.65:52782 mpr2:http TIME_WAIT TCP 192.168.1.65:52783 ec2-79-125-28-85:http TIME_WAIT TCP 192.168.1.65:52785 mpr2:http TIME_WAIT TCP [::]:135 WIN-L969VFMO5GO:0 LISTENING TCP [::]:445 WIN-L969VFMO5GO:0 LISTENING TCP [::]:3389 WIN-L969VFMO5GO:0 LISTENING TCP [::]:47001 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49152 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49153 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49154 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49155 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49163 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49164 WIN-L969VFMO5GO:0 LISTENING TCP [fe80::7800:6e:735:c444%13]:3389 pc-PC:49161 ESTABLISHED UDP 0.0.0.0:53 *:* UDP 0.0.0.0:500 *:* UDP 0.0.0.0:3702 *:* UDP 0.0.0.0:3702 *:* UDP 0.0.0.0:4500 *:* UDP 0.0.0.0:5355 *:* UDP 0.0.0.0:6514 *:* UDP 0.0.0.0:50854 *:* UDP 0.0.0.0:50856 *:* UDP 0.0.0.0:50858 *:* UDP 0.0.0.0:56952 *:* UDP 127.0.0.1:49293 *:* UDP 127.0.0.1:50781 *:* UDP 127.0.0.1:50855 *:* UDP 127.0.0.1:53143 *:* UDP 127.0.0.1:58363 *:* UDP 127.0.0.1:58653 *:* UDP 127.0.0.1:59769 *:* UDP 127.0.0.1:63390 *:* UDP 127.0.0.1:64492 *:* UDP 169.254.196.68:137 *:* UDP 169.254.196.68:138 *:* UDP 192.168.1.65:137 *:* UDP 192.168.1.65:138 *:* UDP [::]:500 *:* UDP [::]:547 *:* UDP [::]:3702 *:* UDP [::]:3702 *:* UDP [::]:4500 *:* UDP [::]:5355 *:* UDP [::]:50857 *:* UDP [::]:50859 *:* UDP [::]:56953 *:* UDP [fe80::b0e8:29cf:aafb:800c%11]:53 *:* C:\Users\Administrator>

RV220W - Can't open port 20 and 549

Hi there,
I have a static IP address over 100Mbit fiber. I've installed a Mac Mini as a webserver and opened the ports 80, 443 and 5900 and a few others for minor services. Everything works fine: the http server (and https as well) is up and pepole can reach it from wan.
Yesterday I tried to setup the FTP service with less success. Into the ACCESS RULES I enabled the FTP service and, as a result the port 21 opened up.
But if I connect via Cyberduck to the server I can navigate through the folders but I can't download anything. So I tryed to open up the port 20 for data transfer with no result. Same issue when I tryed to setup the AFP service to mount remotely server volumes: port 548 opened up but no success with port 549.
Here are the screenshots of the router pages and the port test results.
It's really weird.
I'm not an IT, so... Am I doing something clamorously wrong or I'm missing something huge?
Thanks in advance for your help.
Piero.

Hi Bro
Based from your screen capture, is this even a Cisco product? If yes, can you paste your latest show runnning-config here for me to assit you?
Problem Description : Unable to access server in private LAN from Internet with FTP, TCP/548 and TCP/549.

Can i open an SQL express 2005 database in SQL server express 2012?

Hi,
i have a database and it's in SQL express 2005 but because my windows 8 is not compatible with the installer, i have to install the latest 2012 installer. my problem now is that i cannot open it in the 2012 edition..what do i have to do?

Hi white_roses,
Could you let us know how do you restore the database to SQL Server 2012 Express edition? Please help to collect the detail error information of this issue, it will benefit for us to do further investigation.
As Sandesh and ED suggested above, we can directly detach our databases from SQL Server 2005 and then attach them to SQL Server 2012. For detail steps, please refer to the following article:
http://msdn.microsoft.com/en-us/library/ms187858.aspx
After we move a database from the instance of SQL Server on server A to the instance of SQL Server on server B, users may be unable to log in to the database on server B. If need the logins information on Server B, please refer to the following article:
http://support.microsoft.com/kb/918992
If you have any question, please feel free to let me know.
Thanks,
Jerry Li

Can't Open ports

I have been having a major issie forwarding ports to my 10.6.8 server.   For two years worked great   then zap issues all over the place mostly with thos ei meed for getting the server to be remotely controls, with ssh and with HTTP
OK thought being router died.. I had been using DLINK 655 but about the same time all three start being a bain
I switched to asus RT-AC66u . wen through configuration and same situation
I connect to my ISP with a Starbridge 317 ADSL: modem.. It is set in bridge mode    My ISP assures me no configuratioj required.
Ok to take the router out of the Equation hook the serve straight to the modem and connect PPoE    if anything situation gets worse I have nothing showing open except port 548
The firewall service is OFF
any thoughts or suggestions?

If you have connected your server directly to the DSL modem on your public static IP address and TCP port 548 is visible from remote sites but no other ports are open though Server Admin.app shows various other services are active, then you've either got a very selective problem with the DSL router or any upstream port filtering at your ISP, or your server is misbehaving. You can confirm your ISP is not filtering by swapping in a different server with some of the same ports open as your primary server, and re-verify the test.
Also run a port scan of your server on the local network using your LAN-local network addresses (with the server's original local address, and not via the DSL modem) and see if there are ports open; Network Utility can run a simple port scan, as can some command-line tools. Swapping IP addresses can sometimes get various services tangled, so make sure you're testing with and using the original (presumably with NAT, presumably in a private address block) IP address for the server.
If the services are reported as active via Server Admin.app but Network Utility or another port scanner does not show the expected ports are open, then check the server log files via Console.app or similar, and see what's happened with the various services. if the various server processes are tipping over, then they'll usually be pretty chatty in the logs.

Can't open ports on TMG 2010

The main issue is that the external Lync clients can't connect to the Lync server. The reason this happens is blocked ports on TMG.<o:p></o:p>
There is Non-web server publishing rules setup allowing inbound connection from public ip to Lyncedge server's external ip using tcp ports: 443, 444, 445, 5061, 50000-59999 (inbound).<o:p></o:p>
All the rules use to work fine and the external Lync clients were connecting fine, but now when i test the ports on the public ip, using
web tools (like checkmyports.net) I am getting "Port is Closed" for all of them.
What is not allowing the ports to be open?<o:p></o:p>
Nothing has been changed on the TMG server. The other rules (Activesync and OWA access) on the TMG work with no problem.<o:p></o:p>
Any help would be greatly appreciated!<o:p></o:p>

Hi，
Thank your for your post here.
Please double check your configuration via the article below:
http://ucbeacon.blogspot.com/2013/03/configure-forefront-tmg-2010-as-reverse.html
Please also check the TMG live logging.
Best Regards
Quan Gu

Need Help ! I Can't open Final Cut Express 4.0.1 after installed

I am the new FC E user, i just bought the s/w yesterday and installed into my new Mac Book,
but the program can't launch after installed. The LiveType program work ok .
Any suggestion to resolve it ? Thanks .

Thanks, base on your suggestion, i am using FCS remove software to uninstall FCS.
After restart the system and reinstall the FCS 4 with Retail Official DVD disc.
I continue with Software Update from Web to FCS 4.0.1
But the result still the same, below was the report (i also send to Apple)
I check my system was using Quicktime Version 10.0 (90.3.1), any i+ssues ?
Process: translate [317]
Path: /Applications/Final Cut Express.app/Contents/MacOS/Final Cut Express
Identifier: com.apple.FinalCutExpress
Version: ??? (???)
Build Info: FCPApp-807301041~29
Code Type: PPC (Translated)
Parent Process: launchd [101]
Date/Time: 2010-02-22 01:11:33.781 +0800
OS Version: Mac OS X 10.6.2 (10C540)
Report Version: 6
Interval Since Last Report: 615930 sec
Crashes Since Last Report: 101
Per-App Crashes Since Last Report: 11
Anonymous UUID: EB8CB6DE-4A1E-4A26-8E56-82C0F751F5AB
Exception Type: EXC_CRASH (SIGTRAP)
Exception Codes: 0x0000000000000000, 0x0000000000000000
Crashed Thread: 0 Dispatch queue: com.apple.main-thread
Thread 0 Crashed: Dispatch queue: com.apple.main-thread
0 libSystem.B.dylib 0x801bc612 _pthreadkill + 10
1 libSystem.B.dylib 0x801bbebf pthread_kill + 95
2 com.apple.FinalCutExpress 0xb80bfcb4 0xb8000000 + 785588
3 com.apple.FinalCutExpress 0xb80c01bb 0xb8000000 + 786875
4 com.apple.FinalCutExpress 0xb80dda6c 0xb8000000 + 907884
5 com.apple.FinalCutExpress 0xb814551b spinlockwrapper + 1791
6 com.apple.FinalCutExpress 0xb801d03b 0xb8000000 + 118843
Thread 1:
0 libSystem.B.dylib 0x800c58da machmsgtrap + 10
1 libSystem.B.dylib 0x800c6047 mach_msg + 68
2 com.apple.FinalCutExpress 0xb819448f CallPPCFunctionAtAddressInt + 206155
3 libSystem.B.dylib 0x800f2fbd pthreadstart + 345
4 libSystem.B.dylib 0x800f2e42 thread_start + 34
Thread 0 crashed with X86 Thread State (32-bit):
eax: 0x00000000 ebx: 0x8027c500 ecx: 0xb7fff9ac edx: 0x801bc612
edi: 0xb8211620 esi: 0x00000005 ebp: 0xb7fff9d8 esp: 0xb7fff9ac
ss: 0x0000001f efl: 0x00000286 eip: 0x801bc612 cs: 0x00000007
ds: 0x0000001f es: 0x0000001f fs: 0x00000000 gs: 0x00000037
cr2: 0x801bc608
Binary Images:
0x80000000 - 0x8006afe7 libstdc++.6.dylib ??? (???) <411D87F4-B7E1-44EB-F201-F8B4F9227213> /usr/lib/libstdc++.6.dylib
0x800c5000 - 0x80269feb libSystem.B.dylib ??? (???) <D45B91B2-2B4C-AAC0-8096-1FC48B7E9672> /usr/lib/libSystem.B.dylib
0x802e9000 - 0x802ecfe7 libmathCommon.A.dylib ??? (???) <1622A54F-1A98-2CBE-B6A4-2122981A500E> /usr/lib/system/libmathCommon.A.dylib
0x8fe00000 - 0x8fe4162b dyld 132.1 (???) <226BF7A0-94E0-2F4C-6D6B-9189C952331C> /usr/lib/dyld
0xb8000000 - 0xb81defff com.apple.FinalCutExpress 4.0.1 (4.0.1) <3E4E06B8-E1FC-B232-1371-643DC0FBE8C9> /Applications/Final Cut Express.app/Contents/MacOS/Final Cut Express
0xffff0000 - 0xffff1fff libSystem.B.dylib ??? (???) <D45B91B2-2B4C-AAC0-8096-1FC48B7E9672> /usr/lib/libSystem.B.dylib
Translated Code Information:
NO CRASH REPORT
Model: MacBook6,1, BootROM MB61.00C8.B00, 2 processors, Intel Core 2 Duo, 2.26 GHz, 4 GB, SMC 1.51f53
Graphics: NVIDIA GeForce 9400M, NVIDIA GeForce 9400M, PCI, 256 MB
Memory Module: global_name
AirPort: spairportwireless_card_type_airportextreme (0x14E4, 0x93), Broadcom BCM43xx 1.0 (5.10.131.6 )
Bluetooth: Version 2.2.4f3, 2 service, 1 devices, 1 incoming serial ports
Network Service: AirPort, AirPort, en1
Serial ATA Device: Hitachi HTS545025B9SA02, 232.89 GB
Serial ATA Device: MATSHITADVD-R UJ-898, 907.9 MB
USB Device: Built-in iSight, 0x05ac (Apple Inc.), 0x8507, 0x24400000
USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0236, 0x04600000
USB Device: RAPOO Mouse 7100, 0x04fc (SUNPLUS TECHNOLOGY CO., LTD.), 0x05da, 0x04100000
USB Device: BRCM2070 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x06100000
USB Device: Bluetooth Module, 0x05ac (Apple Inc.), 0x8218, 0x06130000

Can't Open ports in Express

Similar Messages

Maybe you are looking for