Can't ping, email or access my domain -- on occasion.

Very weird but I have no idea what is happening. We have two MacBook Pro's one 15 and one 13, both have mobile me and some pop email accounts with our own domains. Also have iphones that connect to the same network, all connecting to Airport Wireless.
So on occasion I can't access one of my domains (for example mydomain.com). So, when it happens:
1) I can't access the domain in mail, or entourage (on wife's computer). says: "There may be a problem with the mail server or network. Verify the settings for account “mydomain.com” or try again."
2) I can't ping mydomain.com
3) I can't access it via the web browser.
I know the site is up and running because:
1) if I turn off wifi on iphone and go through att, email and safari access the domain ok.
2) I can also go to another domain that is on the same server and the same IP (via web browser, webmail and via ping).
3) I can also take my computer to the office and access the domains ok.
So It is as if the airport DNS tables at home get hung up on mydomain.com (perhaps because all the devices checking the same domain for email)? I've rebooted both the computer and Airport, and even cleared DNS cache on my local computer. Still nothing. I have to wait until it just magically starts working again.
So I'm out of ideas. Any Apple Ninjas out there care to take a guess on what my problem is? Is there a way to reset the router DNS without having to reset the device.
Thanks in advance for help!
Message was edited by: vadas

Go to System Preferences and then head to Sharing. See if there's anything weird there.

Similar Messages

Can I send email using my own domain address with iCloud the way I can with gmail?

Let's say I own mydomain.com and have a [email protected] email account. I have set that up to forward to gmail, and that would be easy to switch to iCloud. Here's the tricky part: gmail allows me to send email as [email protected] I've been doing this for years and it works, but I'd like to switch from gmail to iCloud. Can I set up this same behavior with an iCloud @me.com address (which I already have but haven't been using yet)? I know I can obviously switch the forwarding of incoming mail to my @me.com address... but can I send [email protected] email through iCloud the way I can with gmail? All of my devices are Apple: a Mac Mini using Apple's Mail app, and an iPhone and an iPad both using the Apple email app, so I'd rather switch everything over from gmail to iCloud.
P.S. Awe, c'mon Apple. Don't turn those fake addresses into links. I just used them for the sake of giving an example.

Ah, I should have made that clear. My domain didn't come from google. It was purchased at and is hosted at dreamhost, but I haven't used their email servers in years - I just route everything through gmail. I actually have a bunch of domains (with websites).
Gmail has an option that lets someone with custom domains send (and receive) email through gmail using the custom domain once Google confirms proper ownership of the domain (to prevent spammers and such). Gmail has a setting for "send email as" which allows gmail to be sent using a custom domain as the sender. I'm pretty sure Apple's old mobileme had this feature too, but I didn't use it.

Can't send email to my own domain

The mail program on my iphone works fine, except for one thing - i can't send email to anyone using the domain name as me (our business has its own email domain).
Since most of my emails are to other people inside our business, this is very frustrating).
I am guessing I have done something silly in the set up, but am too much of a novice to figure it out.
Any suggestions?

Sorry - typo in the above question. Should read:
"I can't send email to anyone using the SAME domain name as me"
Tks.

No errors with NAT or DHCP, but can't ping server or access internet

2 weeks ago my Xserve was positioned directly behind a modem and acted as the router to my small office - supplying DHCP, NAT, etc. Then, the Xserve lost it's connection to the internet. The Xserve was unable to pull an address from the modem (via DHCP) and troubleshooting the issue with my ISP resulted in getting my modem swapped.
My Xserve is still unable to pull an address via DHCP directly from the modem. So, I called apple support. The tech I spoke to was extremely helpful and instructed me to place the Xserve behind a router so it could use a static ip - without having to pay my ISP for one. So, I did as he instructed.
Regardless, since my Xserve originally lost connection to the internet I have been unable to get my Xserve to supply NAT to my internal network successfully. DHCP is working fine, the firewall isn't logging any refusals, NAT isn't returning errors. All internal network functions work, I just can't access the internet from any machine other than the server.
Here is the network port breakdown:
Ethernet 1 (wan)
ip: 192.168.1.2
sub: 255.255.255.0
router: 192.168.1.1 (router supplying static ip)
dns: 208.67.222.222,208.67.220.220 (opendns)
Ethernet 2 (lan)
ip: 192.168.1.3
sub: 255.255.255.0
router: 192.168.1.3
DHCP settings:
start ip: 192.168.1.4
end ip: 192.168.1.254
sub: 255.255.255.0
interface: en1
router: 192.168.1.3
Firewall:
Allow all traffic from "any"
NAT:
IP Forwarding and Network Address Translation
External network interface: Ethernet 1
NAT Port Mapping Protocol enabled.
Other notes: I can see the Xserve from any device on the network (in Finder running OS X) but I cannot ping it via the router's ip. (example: ping 192.168.1.3) 100% packet loss.
The Xserve does have access to the internet.
The Xserve leases an ip to the devices on the network, but cannot ping them using their leased ip address.
Initially, I was receiving the following error:
"xserve subnets: create failed, Invalid/missing 'net_address' property
So I modified bootpd.plist by adding:
<key>net_address</key>
<string>192.168.1.0</string>
I no longer receive the error and DHCP works properly.
Any help is thoroughly appreciated as this issue has set me back over a week in troubleshooting.

Thanks again.
I'll try to be more clear about my current setup:
Modem
->
Router
DHCP enabled but supplying server with static ip of: 192.168.1.2 - hence my Ethernet 1 settings on my Xserve. The DHCP address the router supplies to other devices range between 192.168.1.101 - 192.168.1.150 (this is temporary). I'm using the Router as a temporary network connection for devices as I continue to setup the server. Once the server is completed, I will hook everyone up through the switch.
->
Xserve
The Xserve receives a static IP from the router above (192.168.1.2) even though the router gives DHCP addresses to other devices. The Xserve then goes out Ethernet 2 to (which has also been assigned a static internal address: 192.168.1.3) a switch.
->
Switch
The Switch definitely has DHCP disabled, and merely extends the network connection.
Right now, the Xserve is doing nothing other than attempting to supply an internet connection to devices attached to it. I performed a clean install after a day or two of troubleshooting.
I really want to be able to control content access as well as give certain devices priority over others using the Xserve. I want it to control... the network, in all aspects: DNS, Open Directory (Master), Firewall etc. Am I still able to control the network with the Xserve if it is hooked up side by side to the clients without reconfiguring my router to hop through the Xserve before going to the internet? If not, why not just use the Xserve as a middle man as I currently do?
What are the benefits of using it side by side to the clients? What are the drawbacks of my current setup? (Other than it not functioning)

How can i send email from a custom domain connected to gmail on iphone?

Hi there,
I am trying to add a gmail account to my iphone 5S which i have added a custom godaddy email to through pop3 but when i add the gmail account i cant send from the custom domain email.
lets say the account is [email protected] with a [email protected] email attached to it, is there a way of sending emails from my iphone from this address?
I have tried to find other guides but cannot seem to.
thanks in advance

Look in the JavaMail forum on how to create Mime format emails. This allows you to use HTML instead of plain text.
Anthony

I can connect my cisco mobile vpn but can't ping & access internal IP

Hi somebody,
i've configured mobile vpn configuration in cisco 7200 with GNS3. i can connect VPN to my cisco router with cisco vpn client software from outside. but i can't ping to internal ip and can't access internal resources.
My Internal IP is 192.168.1.x . And IP for mobile VPN client from outside is 172.60.1.x.
Your advise will be appreciate.
here is my configuration with cisco 7200 in GNS 3,
OfficeVPN_Router#sh run
Building configuration...
Current configuration : 2186 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname OfficeVPN_Router
boot-start-marker
boot-end-marker
enable secret 5 $1$E0Gz$U8UzNtHOXy2CeoEFj30by0
aaa new-model
aaa authentication login userlist local
aaa authorization network grouplist local
aaa session-id common
ip cef
no ip domain lookup
username asm privilege 15 password 0 pncsadmin
username user privilege 15 password 0 pncsadmin
username user1 privilege 15 password 0 pncsadmin
username cisco123 secret 5 $1$lCOc$Db.e8AFd/0f02ZI4/aeV./
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
crypto isakmp client configuration group MWG
key cisco
dns 165.21.83.88
pool vpnpool
acl 101
netmask 255.255.0.0
crypto ipsec transform-set myset esp-aes esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map mymap client authentication list userlist
crypto map mymap isakmp authorization list grouplist
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap 10 ipsec-isakmp dynamic dynmap
interface FastEthernet0/0
no ip address
shutdown
duplex half
interface FastEthernet1/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex full
speed 100
interface FastEthernet1/1
ip address 200.200.200.200 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map mymap
ip local pool vpnpool 172.60.1.10 172.60.1.100
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 200.200.200.201
no ip http server
no ip http secure-server
ip nat inside source list 111 interface FastEthernet1/1 overload
access-list 101 permit ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 deny ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 permit ip any any
control-plane
gatekeeper
shutdown
line con 0
exec-timeout 0 0
password cisco123
logging synchronous
stopbits 1
line aux 0
stopbits 1
line vty 0 4
password cisco123
end
OfficeVPN_Router#sh ver
Cisco IOS Software, 7200 Software (C7200-A3JK9S-M), Version 12.4(25), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 21-Apr-09 18:50 by prod_rel_team
ROM: ROMMON Emulation Microcode
BOOTLDR: 7200 Software (C7200-A3JK9S-M), Version 12.4(25), RELEASE SOFTWARE (fc2)
OfficeVPN_Router uptime is 30 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19
System image file is "tftp://255.255.255.255/unknown"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 7206VXR (NPE400) processor (revision A) with 245760K/16384K bytes of memory.
Processor board ID 4279256517
R7000 CPU at 150MHz, Implementation 39, Rev 2.1, 256KB L2 Cache
6 slot VXR midplane, Version 2.1
Last reset from power-on
PCI bus mb0_mb1 (Slots 0, 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb0_mb1 has a total of 600 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4, 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port Adaptor
Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>
for c7200 bandwidth points oversubscription and usage guidelines.
3 FastEthernet interfaces
125K bytes of NVRAM.
65536K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
8192K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102
OfficeVPN_Router#

Dear Javier ,
Thanks for your info. i already tested as you say. but still i can't use & ping to my internal IP which is behind cisco VPN router. i posted my config file.
OfficeVPN_Router(config)#ip access-list resequence 111 10 10
OfficeVPN_Router(config)#do sh run
Building configuration...
Current configuration : 2201 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname OfficeVPN_Router
boot-start-marker
boot-end-marker
enable secret 5 $1$E0Gz$U8UzNtHOXy2CeoEFj30by0
aaa new-model
aaa authentication login userlist local
aaa authorization network grouplist local
aaa session-id common
ip cef
no ip domain lookup
username asm privilege 15 password 0 pncsadmin
username user privilege 15 password 0 pncsadmin
username user1 privilege 15 password 0 pncsadmin
username cisco123 secret 5 $1$lCOc$Db.e8AFd/0f02ZI4/aeV./
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
crypto isakmp client configuration group MWG
key cisco
dns 165.21.83.88
pool vpnpool
acl 101
netmask 255.255.0.0
crypto ipsec transform-set myset esp-aes esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map mymap client authentication list userlist
crypto map mymap isakmp authorization list grouplist
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap 10 ipsec-isakmp dynamic dynmap
interface FastEthernet0/0
no ip address
shutdown
duplex half
interface FastEthernet1/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex full
speed 100
interface FastEthernet1/1
ip address 200.200.200.200 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map mymap
ip local pool vpnpool 172.60.1.10 172.60.1.100
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 200.200.200.201
no ip http server
no ip http secure-server
ip nat inside source list 111 interface FastEthernet1/1 overload
access-list 101 permit ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 deny ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 permit ip 192.168.1.0 0.0.0.255 any
control-plane
gatekeeper
shutdown
line con 0
exec-timeout 0 0
password cisco123
logging synchronous
stopbits 1
line aux 0
stopbits 1
line vty 0 4
password cisco123
end

VPN client connected to VPN but can't ping or access to server

HI ,
i need help urgently, had been troubleshooting for a day, but have no ideal what wrong with the config.
Basically there is 2 set of VPN configured, one is site to site IPSEC VPN and another one is connect via VPN client software coexist in same router.
This recently we having problem on client can't access or ping to internal server which is 192.168.6.3 from VPN client software.
VPN client will connect to VPN ip pool as10.20.1.0 to 10.20.1.100
Software itself shown connected but request time out when ping.
Below is the config. Some of the command might be extra as when i did some test, but end up didn't work.
aaa new-model
aaa authentication login userauthen local
aaa authorization network adminmap group VPNClient
aaa authorization network groupauthor local
aaa authorization network map-singapore local
crypto isakmp policy 10
encr 3des
authentication pre-share
group 2
crypto isakmp key emptyspace address 203.142.83.218 no-xauth
crypto isakmp keepalive 15 periodic
crypto isakmp client configuration address-pool local ippool
crypto isakmp client configuration group map-singapore
key cisco123
dns 192.168.6.3
domain cisco.com
pool ippool
acl 102
crypto isakmp profile VPNclient
   match identity address 27.54.43.210 255.255.255.255
   match identity group vpnclient
   client authentication list userauthen
   client configuration address respond
crypto ipsec security-association idle-time 86400
crypto ipsec transform-set REMSET esp-3des esp-md5-hmac
crypto ipsec transform-set DYNSET esp-aes esp-md5-hmac
crypto ipsec transform-set esp-3des-sha esp-3des esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set DYNSET
set isakmp-profile VPNclient
reverse-route
crypto map VPNMAP client authentication list userauthen
crypto map VPNMAP isakmp authorization list map-singapore
crypto map VPNMAP client configuration address respond
crypto map VPNMAP 10 ipsec-isakmp dynamic dynmap
crypto map VPNMAP 11 ipsec-isakmp
description VPN to ASA5520
set peer 203.142.83.218
set security-association lifetime kilobytes 14608000
set security-association lifetime seconds 86400
set transform-set REMSET
match address 100
interface GigabitEthernet0/0
ip address 27.54.43.210 255.255.255.240
ip nat outside
no ip virtual-reassembly
duplex full
speed 100
crypto map VPNMAP
interface GigabitEthernet0/1
ip address 192.168.6.1 255.255.255.0
ip nat inside
no ip virtual-reassembly
duplex full
speed 100
interface GigabitEthernet0/2
description $ES_LAN$
no ip address
shutdown
duplex auto
speed auto
ip local pool ippool 10.20.1.0 10.20.1.100
ip forward-protocol nd
ip pim bidir-enable
no ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface GigabitEthernet0/0 overload
ip nat inside source list 101 interface GigabitEthernet0/0 overload
ip nat inside source route-map nonat interface GigabitEthernet0/0 overload
ip nat inside source static 192.168.6.3 27.54.43.212
ip route 0.0.0.0 0.0.0.0 27.54.43.209
ip route 192.168.1.0 255.255.255.0 27.54.43.209
ip route 192.168.151.0 255.255.255.0 192.168.6.151
ip route 192.168.208.0 255.255.255.0 27.54.43.209
ip access-list extended RA_SING
permit ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.0.0.0 0.255.255.255 192.168.6.0 0.0.0.255
permit ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
permit ip 10.20.1.1 0.0.0.100 192.168.6.0 0.0.0.255
permit ip 10.20.1.0 0.0.0.255 10.0.0.0 0.255.255.255
deny   ip any any log
access-list 1 remark Local Network
access-list 1 permit 192.168.6.0 0.0.0.255
access-list 1 permit 192.168.102.0 0.0.0.255
access-list 1 permit 192.168.151.0 0.0.0.255
access-list 2 remark VPNClient-range
access-list 2 permit 10.0.0.0 0.255.255.255
access-list 10 permit 192.168.6.0 0.0.0.255
access-list 10 permit 192.168.102.0 0.0.0.255
access-list 10 permit 192.168.151.0 0.0.0.255
access-list 10 permit 10.0.0.0 0.255.255.255
access-list 100 permit ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 100 permit ip 192.168.102.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 100 permit ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
access-list 100 permit ip host 192.168.6.7 host 192.168.208.48
access-list 101 deny   ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
access-list 101 permit ip 10.0.0.0 0.255.255.255 any
access-list 101 permit ip 192.168.6.0 0.0.0.255 any
access-list 102 permit ip 10.0.0.0 0.255.255.255 any
access-list 120 deny   ip any any log
access-list 120 deny   ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255 log
access-list 120 deny   ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
access-list 120 deny   ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
no cdp run
route-map nonat permit 10
match ip address 120
control-plane
alias isakmp-profile sh crypto isakmp sa
alias exec ipsec sh crypto ipsec sa
banner motd ^CC^C

I did not try to ping 4.2.2.2. I just know I can not ping comcasts dns servers. I have updated the firmware on the router and it did not work. The computer was able to access the internet until about a week ago, I don't understand what could have changed that I would now need a static DNS.

Can't send email from internal server, same domain name as external.

We have a domain "example.com", hosted externally, for email and a website. We are thinking of hosting email 'inhouse' and have setup a dedicated subdomain on a 'fixed' IP, "mini.example.com" for AFP services mainly. mini.example.com provides DNS internally, its primary zone is also example.com. All access to the external web goes thru' a modem/router that the server is connected to. We have to set an A record for www access to our website.
In our testing to migrate email, the internal setup works fine, until the switch over. Now we can receive mail to the mini server, but can't send any out.
We instructed our webhost provider to set the CNAME mail.example.com to point to mini.example.com and created a cPanel MX extry mail.example.com, 10 priority. Previously, the external host had CNAME as mail.example.com to example.com and MX as example.com, 10 priority.
Since the implementation of the CNAME change, we can't send emails out and they get stuck at the outbox waiting. Client Mail app, says to check for port and SSL and account settings.
Any idea where we went wrong here and what we can do to get emails out? We could go to each computer and point-off the DNS to office IP, but we rather not.
Thanks!

Thank you Camelot and MrHoffman for your replies.
I got in this am to find Mail.app could actually send out emails and I'm stratching my head wondering what happened yesterday.
SMTP server addresss was manually set to mail.example.com for all accounts. In trying to get things to work, the mail setup was redone again by "Accounts", in Systems Preferences, when Login is clicked on, and mail was automatically given a SMTP as mini.example.com instead of mail.example.com. I'm guessing that that could be where the initial 'inside' problems were, given that it had a 0 answer to the MX query. Or then again I wasn't patient enough.
Just for completeness, and if there's something to learn from here, these are the dig results for example.com as seen from within the office network.
============================
~ dig mx mini.example.com :
; <<>> DiG 9.6-ESV-R4-P3 <<>> mx mini.example.com
;; global options: +cmd
;; Got answer:
;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 1791
;; flags: qr aa rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 1, ADDITIONAL: 0
;; QUESTION SECTION:
;mini.example.com. IN MX
;; AUTHORITY SECTION:
example.com.                    10800          IN          SOA          mini.example.com. dnsadmin.example.com.example.com. 2011120603 86400 3600 604800 345600
============================
~ dig mx mail.example.com :
; <<>> DiG 9.6-ESV-R4-P3 <<>> mx mail.example.com
;; global options: +cmd
;; Got answer:
;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 36128
;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 1, ADDITIONAL: 0
;; QUESTION SECTION:
;mail.example.com.                    IN          MX
;; ANSWER SECTION:
mail.example.com.          10800          IN          CNAME          mini.example.com.
============================
~ dig mail.example.com :
; <<>> DiG 9.6-ESV-R4-P3 <<>> mail.example.com
;; global options: +cmd
;; Got answer:
;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 35095
;; flags: qr aa rd ra; QUERY: 1, ANSWER: 2, AUTHORITY: 1, ADDITIONAL: 0
;; QUESTION SECTION:
;mail.example.com.                    IN          A
;; ANSWER SECTION:
mail.example.com.          10800          IN          CNAME          mini.example.com.
mini.example.com.          10800          IN          A          10.0.0.34
;; AUTHORITY SECTION:
example.com.                    10800          IN          NS          mini.example.com.
============================
~ dig mx example.com :
; <<>> DiG 9.6-ESV-R4-P3 <<>> mx example.com
;; global options: +cmd
;; Got answer:
;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 47951
;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 1, ADDITIONAL: 1
;; QUESTION SECTION:
;example.com.                              IN          MX
;; ANSWER SECTION:
example.com.                    10800          IN          MX          10 mail.example.com.
;; AUTHORITY SECTION:
example.com.                    10800          IN          NS          mini.example.com.
;; ADDITIONAL SECTION:
mini.example.com.          10800          IN          A          10.0.0.34

Can't get email since I added personal domain.

Hello,
I have changed my web hosting to .mac and set up my personal domain. hurray! now i can't get emails to respond to my personal email account. i used zoneedit.com to direct traffic to web.mac.com, but i don't know how to fix the email. my domain is registered through melbourne IT and it doesn't allow me to add a subdomain for the email. every time i try to send an email to my [email protected] account it says:
Each of the following recipients was rejected by a remote mail server.
The reasons given by the server are included to help you determine why
each recipient was rejected.
Recipient: <[email protected]>
Reason: 5.7.1 Recipient access denied
this is turning out to be more difficult than it should be. help??
hb

The answer to your problem is simple. Change your domain provider.
www.1and1.com is probably the best for you and iWeb use.
That's what I did. It's all automatic and takes just few days. And no more problems after that.
More info here: http://faq.1and1.com/domains/domain_transfers/index.html
To initiate a transfer you just need a credit or debit card. Then go to 1and1.com and check availability for your domain. Just type it into the Step 1 field on the their home page. It will not be available but next to it is gonna be TRANSFER DOMAIN button. Hit it and follow instructions.
Then look at this message:
http://discussions.apple.com/thread.jspa?threadID=1288484&tstart=0

How can I make a email at my muse domain

I just wanted to know how to make an email at my own domain so that i don't have to subscribe to something like godaddy.

Using Adobe Hosting :
- You would need to upgrade site plan to web basic+ which includes email service.
- After adding domain , you can create email records which would be on default domain added to site.
Using external hosting :
- If your hosting provides email service then you can create email records on your domain
- Or use third party email service.
Email account creation is done on hosting platform wherever you are hosting your site.
Thanks,
Sanjit

Can Multiple Webgate/OAM/IdentityStores access one multitenant WLS domain?

Can multiple access points ( web tier + OAM + Identity store) access one application?
The objective here is to have one multi-tenant ADF application accessed by users who are authenthicated by their own enterprise sso and identity store. Authenthicated session should pass the context with list of all enterprise roles that user belongs to which would be used for authorization by the multitenant application. It is assumed here that naming convention for relevant roles is followed by all participating identity stores.
Can Webgate/OAM and accessed WebLogic domain be configured to accomplish this?

OAM can pass as header variables all of the things you mention. For example, you get these by default:
OAM_REMOTE_USER containing the userid of the logged in user (eg "jsmith")
HTTP_OAM_IDENTITY_DOMAIN containing the name of the Identity Store that the logged in user belongs to, as known to the OAM admin console (eg "SunLDAP")
additionally you can define a headervar that contains the user's ldap group membership, and one that contains the user's full DN (or any other attribute and other information).
Of course, any receiving app would need to be configured to consume this information.
Regards,
Colin

Iphone 4s in settings can't access Notes or Mail. Also can't access mail from home screen. Can't send email. All else is good.

I need help. I have reset my iphone. I have turned it off then on. Still can't launch my built in mail app from home screen. When I try it goes to blank page then right back to home screen view.
In settings for the iphone 4s I can not access Notes or Mail, Contacts,Calendars. When I tap either of the two they highlight in blue and then go right back to Home Screen view. I seem to be able to access everything else in settings with no trouble.
From home screen I have no trouble I can launch the built in utility Notes with no problem. I also can launch Calendars from Home Screen view. My Contacts are still reachable by tapping Phone from H/S view then clicking on contacts.
I can not launch mail. nor can I send email. Also the built in mail app is not showing it is recieving mail either. All else seems fine.
I can log in to my email from Safari on iphone and from my laptop with no problem.
Anyone have any suggestions? My iphone is out of warranty. Apples only suggestions are To pay for support.
Thanks in advance

Just had a thought....was trying to rememberif anything changed last night. I think I installed a mac OS X Security update. That's about the time the trouble started. Any ideas? Thanks.

Where I can find the logs in Exchange that I can check or see if our mail server accepted the emails from a certain domain.

Good day, I would like to know where I can find the logs in Exchange that I can check or see if our mail server accepted the emails from a certain domain. The problem is we can receive emails
from other domains like yahoo,gmail etc but from a specific domain we cannot receive emails from them. I checked the whitelist of our Exchange and that domain is currently listed.

As suggested above, Message tracking is your option to get these reports into your environment.
To gather more information about, you may walk through this informative technet resource :
https://technet.microsoft.com/en-us/library/bb124926%28v=exchg.150%29.aspx
Here is another :
https://technet.microsoft.com/en-us/library/bb124375%28v=exchg.150%29.aspx
Moreover, if you wish to find this report into real time, you may consider on this automated solution (http://www.exchangereports.net/) that could be a good alternative approach for you.

I suddenly can't receive emails from senders at a particular domain. They can receive emails from me. I haven't blocked them. Any suggestions on how to 'reopen the line' will be appreciated, thanks.

I suddenly can't receive emails from senders at a particular domain. They can receive emails from me. I haven't blocked them. Any suggestions on how to 'reopen the line' will be appreciated, thanks.

Contact iCloud support. Apple's spam filters may have detected spam coming from users on that domain and blocked all email from it.

Hi There for the last few days I can log into Icloud on my pc but I can't action anything. I can see the emails but cannot view them. I cannot compose a new email.. I don't know if this is icloud or my pc? Its working fine when I access on my iphone..

Hi There
for the last few days I can log into icloud via icloud.com on my pc but I can't action anything.
I can see the emails but cannot view them. I cannot compose a new email.. I don't know if this is icloud or my pc?
Its working fine when I access on my iphone.
many thanks
Cherry

Just realised its fine through internet explorer but its Mozilla.. so assuming an issue with my browser?

Can't ping, email or access my domain -- on occasion.

Similar Messages

Maybe you are looking for