Can't ping in or out across the router

Windows Server 2008 R2 Standard. It's a domain controller, file server, and DNS server. It will also soon be a VPN server. It sits on a private network with two other private subnets accessible through site-site vpns via Cisco routers. This server sits on
the main office subnet.
I am unable to ping in or out to/from other subnets. But, I can ping other devices on the main subnet from other subnets. I just can't ping the server and from the server, I can't ping anything on the other two subnets.
I thought it might be a firewall issue on the server but the rules for ICMP are enabled and configured to allow pings in and out to and from anywhere. I even turned the firewall off (didn't stop the service) as a test and still couldn't ping interfaces on
the other subnets.
I'm stumped. Is there something else that might be preventing pings to all but the local subnet? Yes, I can ping the server from the local subnet and from the server, I can ping anything on the local subnet.
Ken

I have verified the TCP/IP settings on this server. The IP address, mask, and default gateway are all correct for this subnet.
I'm testing from a Cisco switch located inside the remote subnet. There isn't an error message, the ping command just reports the following:
Hobbs2960#ping 192.168.1.9
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.9, timeout is 2 seconds:
Success rate is 0 percent (0/5)
Hobbs2960#
A traceroute from that same switch hits the GW on that router ok but times out after that.
Ping and traceroute from that same switch are successful if I ping a different server on the same subnet as the server in question.
Pinging from the server in question gives "Timed out" responses. Tracert from the same server hits the GW, then the outside interface of our local router, then times out.
Again, ping and traceroute from a different server (running AIX) to the same remote switch worked fine.
Thanks!

Similar Messages

  • I cant remember my password to logon to my mac, how can i change it with out needing the old one?

    i cant remember my password to logon to my mac, how can i change it with out needing the old one?

    http://support.apple.com/kb/HT1274

  • Can I zoom in or out using the Camera app on the iPhone 5?

    Can I zoom in or out using the Camera app on the iPhone 5?

    Pinch to zoom in and out.

  • How can i get HD video out from the lumia 900. ? ...

    How can i get HD video out from the lumia 900. ? Is there some kind of gable. ? N8 has HD cable port..so where is lumia`s port. ?

    Download Zune and start it, when started connect your Lumia 900 and you can now transfer mediafiles from the Lumia to your PC through a USB connection. For Mac use the Mac connector.
    Press the 'Accept As Solution' icon if I have solved your problem, click on the Star Icon below if my advice has helped you!

  • How can i get my email out of the file box icon?

    How can I get my email out of the file box icon? Sometimes I touch it by accident and the email message goes in there.

    Another thing to try is renaming it with a .htm or .html extension.
    If that doesn't work either, do you have any other files from your old system? In particular, if you have your old places.sqlite file, you could use that to overwrite your new places.sqlite (bookmarks+history) file.

  • My iPad Air is disabled after wrongpassword attempts.I didn't sync it with my laptop also. How can I restore it with out losing the data.

    My iPad Air is disabled after wrongpassword attempts.I didn't sync it with my laptop also. How can I restore it with out losing the data.

    You can't unlock it without losing data. It's too late for that now. You totally erase the iPad when you unlock it and you will have to start all over again. Most of your purchased content can be downloaded again.
    Forgot passcode for your iPhone, iPad, or iPod touch, or your device is disabled - Apple Support
    Download past purchases - Apple Support

  • If I buy iphone 5 from Sprint ,  can i use GSM network out of the US ?

    If I buy iphone 5 from Sprint ,  can i use GSM network out of the US ?

    hi there,
    you could buy it somewhere in Europe. I know Apple sells them unlocked here in Germany and if I am not mistaken also (among others) in France and Italy.
    Yet, as Peter wrote, the warranty can become a problem. Not sure whether a one country only rule goes for the European Community as well though.
    As for the price, the 16 GB model costs 679,- € (equals roughly 550 £). Currently there is an average delivery time of 4 to 5 weeks.
    LTE connections will not work with Orange or Vodafone. Only EE is about to offer a compatible LTE network. DC-HSPA and regular HSPA+ will work fine.
    regards, Chris

  • Can time m/c & capsule backup across the web??

    Can time m/c & capsule backup across the web??
    It works great in my home network but what if my house burns down!
    I was thinking I could have my time capsule at my buddies place and vice versa and backup across the web.
    That way if either of us has the likes of a fire or theft we can retrieve from the other person's place.
    I assume we'd have to create some form of VPN through each of our routers to be able to find the remote time capsule volumes/drives. If we use time capsule's for that or an AirPort Extreme is that "easy"??
    TIA
    barry

    apple get it together.
    lets see all the money you have gotten from me over the years
    one iphone 3g
    two iphones 4s
    two white macbooks
    one macbook pro
    one 13" macbook air
    one 11"macbook air
    one time capsule
    one 27' imac
    one mac mini
    =   about $10,000 dollars give or take over the last 4-6 years how dare you
    but if i call support your going to charge me money just to speak to a so called genious? I want to be able to use my **** time capsule is that so much to ask?

  • I just got my cable company to switch my wireless router to a wired one considering now I have the wireless airport device (the newest one) but now I can't get a wireless signal. The router works when directlyplugged in,the aiport wireless device is green

    I just got my cable company to switch my wireless router to a wired one considering now I have the wireless airport device (the newest one) but now I can't get a wireless signal. The router works when directlyplugged in,the aiport wireless device is green. I've tried going through my new MacBook Pro settings and it the diagnostics check, it says network changes detected, I tell it that it "yes" does connect to a cable modem, it tells me to restart it, after I do it asks if there are any other devices hooked up ( firewall) and when I say no it tells me that it can't fix the problem.
    Now I know that I probably have a new IP address because of the cable company switching the boxes but it was working fine with the other box, now there isn't a signal to be had on it!
    Please anybody out there that can help!!!??

    Any time you change networking hardware it is always a good idea to perform a complete power recycle with the new equipment. Check out the following AirPort User Tip. Please post back your results.

  • How can I disable wireless admin privileges to the router ?

    I am using an Airport Utility for Windows for Airport Extreme. For the sake of better security, how can I disable wireless admin privileges to the router so that the router can only be configured via hardwire connection?

    For the sake of better security, how can I disable wireless admin privileges to the router so that the router can only be configured via hardwire connection?
    Sorry, but this is not possible.
    If you want to limit access to administration of the router, you should change the Base Station password, and only give out that password to those individuals that you want to have access to the administration settings of the router.
    The forums have been having problems displaying screenshots, but we will attach one below in the hopes that the problems may be fixed.
    Important Note.......even with this,  "security" on the AirPort routers is an illusion.......since a one second press on the reset button will give any user 5 minutes of free access to go in and change any settings that they want. 
    So, you might want to keep any eye on things.

  • Connected to Internet but can't Browse-Rig​ht out of the Box!

    Hello, I am having trouble loading web pages when connected to the internet via wireless (LAN works fine).  My network sharing center says i'm connected to the internet and when i troubleshoot it finds no problems. Occasionally the google or youtube homepage will load, but no more than that. An error message is never displayed either, the web page simply loads forever until i close out of it. Something odd I've noticed is that, if i cut the wireless on my laptop off then back on, I have around 30 seconds of browsing freedom--everything works; however, after that it returns to endless load times. All the other laptops in my house have no issues with the wireless. Anyways, I've looked for solutions all over the internet and none have fixed this problem. I just received my Lenovo t530 yesterday and this was a problem right out of the package. I hope someone can help.

    Peytizzle,
    Try changing the Channel in the wireless router and see that helps. Also do you have those "N" router? Can you try using only a/b/g?
    Also if you have Channel set to "Automatic" can you try setting it into 1 channel only rather than leaving it in Automatic.
    Let us know
    Thanks
    *Non Lenovo employee*
    I have a Y2P (i5) ... Feel free to ping me if you want me to test some applications with your Y2P if you have the same model. I don't mind keep doing recovery on it if needed .... =)

  • Can values in matrix cells flow across the pages (Reports 6i)?

    Hi,
    I have to display more than 1000 char in a matrix cell. The report errors out when the values in the matrix cells exceeds the page. Can values in matrix cells flow across pages?
    any help on this?
    Thank You,
    -- Raja

    As far as to make the report work, developing the query accordingly using UNION does help.
    But my question is still not answered and no replies as well.
    So I think, Two frames with print direction as down and One frame with print direction as Across is not possible.
    Regards
    Arif

  • Can't stop sound coming out of the sub - T7700

    I was testing something today and noticed that even when i have only audio input plugged in, say the green front jack and have no other speakers attached - Even if i have the jack plugged into the front, or side sound still comes out of the sub. I've tried it with the front and side speakers disconnected and connected all while no input is in the center/sub connection - no matter the combination the sub still plays?Why? how can i have no sub at all?Should mention i've also tried it with the upmix switch in all positions and i'm using an audigy2 zs card not that it would matter though i guess.

    It's worth bearing in mind that speakers really shouldn't do bass redirection, it should be the job of the receiver/decoder. Quite why Creative do things the other way around is anyone's guess. Aaanyway, have you tried simply turning the bass dial right the way down on the volume control box for the speakers? That's the best I can suggest.

  • Can't access bookmarks that overflow across the toolbar. They are there but can only get them by going into bookmarks toolbar in menu. They used to display off to side when you clicked next to last item. Can I fix this?

    This feature always worked before. Then one day it stopped. Can access overflow items on bookmarks toolbar through menu, but rarely across the top. The ones that don't fit across the top can't be brought up anymore.

    This feature always worked before. Then one day it stopped. Can access overflow items on bookmarks toolbar through menu, but rarely across the top. The ones that don't fit across the top can't be brought up anymore.

  • Can not ping, samba or else to the client which connected to the same WRVS4400N router

    I buy a WRVS4400N router. Setup to surf internet successfully.
    But each client can't ping, samba, file sharing to each connect to WRVS4400N.
    In the router admin page. We can see each client connect to the router.
    I have one SSID only. And setup the
    Wireless Isolation (between SSID w/o VLAN)
    and
    Wireless Isolation (within SSID)
    both to disable.
    And have reboot it several times.

    Please post the output of:
    lspci -knn|grep -iA2 net
    How are you attempting to search & connect to your router?
    Please post the exact commands used and the exact terminal output resulting from these commands.

Maybe you are looking for