Can't populate DIMMs properly - Half RAM bandwidth only

Sorry for posting this twice - I did not see a way to delete a post (from a "finished" thread)
Only one CPU can access the RAM at a time, meaning the memory bandwidth is halved:
(rightclick and choose "View Image" for more detail)
I think I know why: I have put the DIMMS in slots NOT supported!
They should be in slots 7&8 and 11&12 instead of 7&8 and 9&10, but the problem is that NONE of the supported DIMM configs WORKS
Any combination from page 2-7 of the Mobo manual results in the system not being able to POST or the system recognizes 2 GB instead of 4 GB and the error log says "Incorrect config - the system has disabled RAM".
This looks like a faulty Mobo to me, or unsupported RAM but it's Corsair - not the worst - and why is 4 GB recognized in the aforementioned (unsupported..) config? (It just results in the 2 CPU's not able to access it simultaneously)
http://www.planetamd64.com/lofiversion/index.php/t472.html says this is a NUMA mobo..
Hm.. Seems I need to fiddle with the population one more time and then return it to the dealer if it still doesn't work.

I found it
Turn Node memory Interleave off, which allows ccNuma to be turned on, which yields double bandwidth in SiSoft Sandra (10 GB/sec

Similar Messages

Can I combine a PC3200 DDR SDRAM with PC25300 DDR2 SO-DIMM when installing ram?

Can I combine a PC3200 DDR SDRAM with PC25300 DDR2 SO-DIMM when installing ram? I am taking ram out of an iMac G5 ALS (2005) to add to the 1GB ram (3GB max) iMac late 2006 model.

kbentz wrote:
The slots are different sizes I have found out as well. Thanks for the advice!
Yes, there is that small issue but even if they were the same slots you'd just be disappointed a little later.

Can I install one 8 GB ram in a MacBook Pro (13-inch, Early 2011).

Can I install one 8 GB ram in a MacBook Pro (13-inch, Early 2011). The other slot is not working, I have only one slot that works. It is stated in this link http://support.apple.com/kb/HT1270#link1 , that the maximum memory is 8 GB where every slot slot has 4 Gb. Is there any problem if i install only one 8 Gb ram in the working slot ?

You should be able to do that.
Maximum Memory
16 GB (Actual) 8 GB (Apple)
Memory Slots
2 - 204-pin PC-10600 (1333 MHz) DDR3 SO-DIMM
Understand that there is no guarantee it will work, but based on the above it should work for you.

If my Mini is running 64 bit can I run more than 4Gb RAM?

I hear ALL over the place that the mini can not use more than 4Gb RAM.
Is this a hardware limitaion of the motherboard/Processor?
OR
Is this due to the fact that mini's run at 32 bit?
You can now easily run modern mini's at 64 bit:
http://blog.leanopen.nl/2010/04/23/doesnt-your-mac-mini-want-to-boot-in-64-bit/
So who knows the REAL answer?
Thanks -
skibum

Most of the Minis are limited to less than 4GB and that is a hardware limitation. The newest Mini with the nVidia video can access more. Apple only supports 4GB because they use matched DIMMs, which on paper have a slight performance improvement over unmatched DIMMs. For whatever reason, Apple doesn't yet support 4GB DIMMs in the Mini. (I suspect that the power requirements or prices for the larger DIMMS may have affected Apple's decision.)
If you do have an appropriate Mini, then you can get compatible 4GB DIMMs from [Macsales|http://eshop.macsales.com/shop/mac-mini> or others. Regardless, although I normally trust Macsales, more than 4GB is not supported by Apple, so you have to take that in to consideration. (i.e.: warranty from Apple or Applecare.)

I can't load gmail properly in Firefox. I've cleared cache, cookies, etc. Happens on more than one computer.

I can not load gmail properly. It refuses to load and suggests loading Basic HTML for slow connections. I do not have a slow connection and have no problem loading gmail in Explorer. This is happening on both Firefox and Firefox Developer. The Firefox Developer problem just happened with the new upload this evening. Regular Firefox has been happening for a couple of months. It happens on both my work computer and my home computer. I tried everything suggested including the suggestion to delete cookies, cache, and the cookies.sqlite file.

You can remove all data stored in Firefox from a specific domain via "Forget About This Site" in the right-click context menu of an history entry ("History > Show All History" or "View > Sidebar > History") or via the about:permissions page.
Using "Forget About This Site" will remove all data stored in Firefox from that domain like bookmarks, cookies, passwords, cache, history, and exceptions, so be cautious and if you have a password or other data from that domain that you do not want to lose then make sure to backup this data or make a note.
You can't recover from this 'forget' unless you have a backup of the involved files.
It doesn't have any lasting effect, so if you revisit such a 'forgotten' website then data from that website will be saved once again.
Create a new profile as a test to check if your current profile is causing the problem.
See "Creating a profile":
*https://support.mozilla.org/kb/profile-manager-create-and-remove-firefox-profiles
*http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Profile_issues
If the new profile works then you can transfer files from a previously used profile to the new profile, but be cautious not to copy corrupted files to avoid carrying over problems.
*http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

2006 iMac running 10.4 OS. I copied files to ext. drive. Put in 10.6 disc and did a clean install (format) of 10.6. Copied data from ext. drive back to Mac. I didn't get all the files. CAN I REVERT BACK TO THE 10.4 OS SO I CAN COPY MY DATA PROPERLY?

2006 iMac running 10.4 OS. I copied files to ext. drive. Put in 10.6 disc and did a clean install (format) of 10.6. Copied data from ext. drive back to Mac. I didn't get all the files. CAN I REVERT BACK TO THE 10.4 OS SO I CAN COPY MY DATA PROPERLY?

How did you copy files to the external drive, and what files did you copy? Did you drag and drop in the Finder? Use a clone utility? What files did not successfully copy?
If you reformatted the drive as part of your install, then you won't be able to recover any files from the drive. Reverting back to (reinstalling) 10.4 will not help you.
Do you have a complete-drive backup of your old system?
Matt

I have a late 2012 iMac and a late 2009 mac mini. I want to know if I can take the 8 GB of ram from the iMac and install it in my mac mini.

I have a late 2012 iMac and a late 2009 mac mini. I want to know if I can take the 8 GB of ram from the iMac and install it in my mac mini.
According to Cruicial my mac mini could use:
Module Size: 8GB Kit (4GBx2)
Package: 204-pin SODIMM
Feature: DDR3 PC3-8500
Specs: DDR3 PC3-8500 • CL=7 • Unbuffered • NON-ECC • DDR3-1066 • 1.35V • 512Meg x 64
Also According to Cruical my iMac uses:
Module Size: 8GB Kit (4GBx2)
Package: 204-pin SODIMM
Feature: DDR3 PC3-12800
Specs: DDR3 PC3-12800 • CL=11 • Unbuffered • NON-ECC • DDR3-1600 • 1.35V
I want to increase the ram in both computers.
So, can I put the iMac ram in my mac mini and then I'd only have to buy ram for my iMac? Naturally the ulitmate test will be when I actually install it, but having an expectation of success or failure will allow me to plan on what to spend money on.
Thanks,
Bear

Thanks for the responses. I probably wont even try as my priority is Ram for the mac mini. 2 is not enough. 8 for my imac is okay for now.
Somewhere I thought I'd heard that faster Ram would simply clock at the lower speed. It seems that I am incorrect.
Thanks,
Bear

Hello, I have an iPod touch and it don't has light or brightness. I can see the icons and use it but can get it work properly. I went to settings and the brightness is adjusted tu full level. Any idea?

Hello, I have an iPod touch and it don't has light or brightness. I can see the icons and use it but can get it work properly. I went to settings and the brightness is adjusted tu full level. Any idea?

Try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.

I plug my ipod into my computer itunes pops up with error message "Ipod detected but can't be identified properly" suggests I unplug and try again or uninstall itunes and reinstall nothing works. What should i do?

I plug my ipod into my computer itunes pops up with error message "Ipod detected but can't be identified properly" suggests I unplug and try again or uninstall itunes and reinstall nothing works. What should i do?

summarizing:
iPod nano (what version iOS BEFORE update?)
downloaded music
updated iPod to iOS 8.1.2
Windows 7 PC
plug-in iPod to PC
error message from iTunes on the PC "Ipod detected but can't be identified properly" ⬅[quoted from your original post] (+ suggested troubleshooting steps)
un-plug > re-plug iPod (how many times?)
iTunes un-installed from PC (?)
iTunes RE-installed to PC (?)
error message repeats(?)
searched "Ipod detected but can't be identified properly" site:support.apple.com with ZERO results - pretty strange that the support site wouldn;t know an iTunes generated error message (?) EDIT - had an "aha! moment when using a fresh Google search page and 'suggested' CANNOT
then "Ipod detected but can't be identified properly" site:discussions.apple.com had ONE result = Can't connect to iTunes with ipod touch (-50 error) - NO REPLIES
CANNOT instead of can't [ tsk tsk ]
iPhone, iPad, or iPod touch not recognized in iTunes for Windows - Apple Support
follow all the instructions in order and let us know

Can i get month, quarterly, half yearly, yearly wise sales report basing on

hi,
sap gurus,
good evening to all,
how can i get month, quarterly, half yearly, yearly wise sales report basing on division and material.
is there any std transaction code for that.
customization is requried for that.
regards,
balaji.t
09990019711

Standard SAP SD Reports:=
Statistic Group:
Purpose u2013 To capture data for Standard Reports, we require to activate Statistic Group as under:
--> Item category (Configuration)
--> Sales document type (Configuration)
--> Customer (Maintain in Master data)
--> Material (Maintain in Master data)
When you generate statistics in the logistics information system, the system uses the combination of specified statistics groups to determine the appropriate update sequence. The update sequence in turn determines for exactly which fields the statistics are generated.
Configuration:
IMG --> Logistics Information System (LIS) --> Logistics Data Warehouse --> Updating --> Updating Control --> Settings: Sales --> Statistics Groups -->
1. Maintain Statistics Groups for Customers
2. Maintain Statistics Groups for Material
3. Maintain Statistics Groups for Sales Documents
4. Assign Statistics Groups for Each Sales Document Type
5. Assign Statistics Groups for each Sales Document Item Type .....
All Standard Reports which are available are as under:
SAP Easy Access: Information Systems -> Logistics -> Sales and distribution ->
1. Customer -> Incoming orders / Returns / Sales / Credit memos / Sales activities / Customer master / Conditions / Credit Master Sheet
2. Material -> Incoming orders / Returns / Sales / Credit memos / Material master / ...
3. Sales organization -> Sales organization / Sales office / Sales employee
4. Shipping point -> Deliveries / Returns
5. SD documents -> Orders / Deliveries / Billing documents ...
& so on.
Regards,
Rajesh banka

Pdf file in simply Chinese can not be displayed properly sometimes, how to solve it?

pdf file in simply Chinese can not be displayed properly sometimes, how to solve it?

Try a different pdf reader, like GoodReader.
Try switching your OS to Chinese (or English, if it is already in Chinese).
Verify that the pdf does display correctly on a full computer.

How can I populate a pdf with database data?

How can I populate a pdf that we have on our server with database data on our server?

Actually, if you export it in the right format then you won't need a script
at all.
You can import data directly into fields from a plain-text file via Tools -
Forms - More Form Options - Import Data...
I believe the format is tab-delimited with the field names in the first row
and their values in the second.

I am importing a video and in iMovie the video is now white. the audio still plays and I can play the video properly outside of iMovie so any help is good?

I am importing a video and in iMovie the video is now white. the audio still plays and I can play the video properly outside of iMovie so any help is good?

I going to recommend again, downloading and installing some video helper applications.
1. http://perian.org/ (this will add a number of different file types to the ones QuickTime already plays)
2. http://www.divx.com/en/software/mac (will add more file types to what QuickTime can play)
Either one of these might be necessary to get MPEG Streamclip to export the video. Failing that the only other thing I have found is an obscurve discussion thread on Avid.com:
http://duc.avid.com/archive/index.php/t-277791.html
I've figured out what the problem is on my end. The video came from Avid on a Windows machine and was encoded with Squeeze. I found out that the 2 seconds of black at the top of the video were at a different frame rate than the rest of the video. I chopped off the 2 seconds of black and started at the first frame of video, exported it with Quicktime Pro and was able successfully view the video in ProTools. Apparently Squeeze will let you create a movie file that has different frame rates within the same movie... This fixed my issue that was exactly as you describe, hopefully it might work for you.
Lastly, you could try converting the video clip using HandBrake

Can the mac mini i7, 8gigs ram, edit avchd 1920/1080p without having to convert it?

Can the mac mini i7, 8gigs ram, external FW800 drive, edit avchd 1920/1080p without having to convert it?
Can you scrub the TL at 5x speed and not have it stutter?

By default it converts it to ProRes 422, though you can specify other codecs.
Why convert it?
Although FCP X can handle AVCHD natively, AVCHD being a "delivery" codec is not really suitable for editing.
ProRes is designed specifically for ease of editing especially with complex effects and colour correction.
If your editing is going to be fairly basic you can get away with leaving your media as AVCHD.
Note also that an hour of ProRes is around 50GB !

I have a new windows 7 computer and I have downloaded the latest version of itunes. How can I populate my itunes music library from my ipod?

I have installed a new windows 7 computer (Dell) and downloaded the latest version of ITunes. How can I populate my music into ITunes from my I-pod classic?

Hey AppleMacParker,
Thanks for the question. The following article may assist you in setting up syncing with your iPod:
iTunes 11 for Windows: Set up syncing for iPod, iPhone, or iPad
http://support.apple.com/kb/PH12313
Select items to sync automatically
1. Connect your iPod, iPhone, or iPad to your computer and select your device.
2. Select the type of media you want to sync.
The types of media you can sync depends on your device. For more information, see Sync and organize iOS apps and Add photos to iPod, iPhone, or iPad.
3. Select the Sync checkbox, and select the items you want to sync automatically each time you connect your device.
Click a button to select the kind of content you want to sync, then select the sync checkbox and select the items you want to sync automatically
The bar at the bottom of the window shows how much space will remain on your device after you sync.
Thanks,
Matt M.

Can't populate DIMMs properly - Half RAM bandwidth only

Similar Messages

Maybe you are looking for