Can't print duplex when using a CS2 doc in CS3

I can't print duplex when opening an old cs2 file in cs3, even when re-saving as a cs3 file. I can print duplex when creating a new document in cs3. The printer is a Xerox 242 Fiery. Any ideas?

I have the same problem with a DocuColor 5065 with firey. InDesign will never remeber the print settings for old CS 1 documents. New CS3 documents are fine. Only happens with this Fiery, all my other fierys work fine. Funny thing is even older documents (v1.5) remeber the print settings fine.
What I do to get around is to just send the file to the RIP, then change the print settings there to what I want then print.

Similar Messages

Can not print report when using HTML or DHTML

Can not print report when using HTML or DHTML. When I open the report and click the print icon I get a small blank dialog box and then nothing. If I change to activex it works and I can print.
Any Ideas?
Thanks
Jeff

Hi,
I did not come across this situation before. Did you apply any fix packs. Try to check whether its a issue which can be fixed by applying fix pack( try to check release notes of fix pack and see if they mentioned any thing about this).
Thanks,
SK.

I can't print. When I go to file-print, nothing happens. My printer is working just fine with IE and everything else.

I can't print. When I go to file-print, nothing happens. My printer is working just fine with IE and everything else.

Try the Firefox SafeMode. <br />
''A troubleshooting mode, which disables most Add-ons.'' <br />
''(If you're not using it, switch to the Default Theme.)''
# You can open the Firefox 4/5/6/7 SafeMode by holding the '''Shft''' key when you use the Firefox desktop or Start menu shortcut.
# Or use the Help menu item, click on '''Restart with Add-ons Disabled...''' while Firefox is running. <br />
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before using the Firefox shortcut (without the Shft key) to open it again.''
If it is good in the Firefox SafeMode, your problem is probably caused by an extension, and you need to figure out which one. <br />
http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes

HP Photosmart 8750 prints slow when using Photo Gray Cartidge

HP Photosmart 8750 prints slow when using Photo Gray Cartidge ... sometimes indicates Black Cartridge failed, however upon reinserting works slow

Welcome to the HP Forums ButchG,
I see by your post that when printing with the photo gray cartridge the black cartridge will indicate that it has failed.
I can help you with this issue.
I would do a power reset to see if that will resolve the issue.
With the printer still turned on, disconnect the power cable from the back of the printer, if the printer has external power module with a detachable power cord disconnect it for 15 seconds and then reconnect it.
Hold down the power button for 10 seconds to drain the power.
Then disconnect the power cable from the wall outlet.
Wait 10 seconds and reconnect the power cable back to the wall outlet first, then the back of the printer and power it on again.
Make sure the printer is connected directly to wall outlet. (don't use a power hub or a surge protector)
I have provided a document for the cleaning the contacts and reseating the cartridge.
'Cartridge Failed' or 'Cartridge Not Compatible' Error Message.
What are the ink levels?
Are you using Genuine HP Cartridges?
Check the date on the cartridges to make sure they are still in warranty. (not old stock)
If you need further assistance, let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Cannot print anything when using safari

Cannot print anything when using safari. OSX is Mavericks. Printer is Canon MP620. Have downloaded Mavericks software for printer, but still will not print. I have also repaired the disk hoping that would solve the problem, but to no avail. Can anyone help me please?

Hey ivorfromborehamwood,
Thanks for using Apple Support Communities.
For more information, take a look at:
Troubleshooting printer issues in OS X
http://support.apple.com/kb/ts3147
Delete the affected printer, then add the printer again.
If the issue persists, try these additional steps:
Reset the printing system, then add the printer again.
If the issue still persists, reset the printing system again. Download and install your printer's drivers. Then, add the printer again.
Have a nice day,
Mario

Disable print output when using bapi BAPI_GOODSMVT_CREATE

Hello,
I am using BAPI BAPI_GOODSMVT_CREATE to post material documents in our programs.
I wish to prevent the print output of the documents created by the BAPI.
Meaning - when the user post good movement using MIGO, there will be a printout of the movement, but if the movement is created using BAPI_GOODSMVT_CREATE, no output will be printed.
I have tried sending blank values in fields VER_GR_GI_SLIP & VER_GR_GI_SLIPX in GOODSMVT_HEADER structure, but to no avail.
Is there a way to disable printing ONLY when using the BAPI?
Thank you very much.

Hi,
We cant restrict the print preview or print out of the material document. Once the condition record has maintianed for the material document, it ll applicable for all the material doc . It would be manual Gr or BAPI GR.
In your case Print is coming automatically or user is taking the print !!
Regards,
Dhanush.

I have iphoto 5, can I print my photobook using apple web store?, as it is for the iphoto 9 users?

I have iphoto 5, can I print my photobook using apple web store, as it is for the iphoto 9 users?
thank you, Silvia

Without upgrading to Leopard or Snow Leopard you would need to find a copy of iLIfe 08. You can look on Amazon.com or eBay.com for a copy.
OT

Can't send mail when using mobile broadband

Hi
I am getting quite frustrated as I can't send mail when using my mobile broadband modem! I can receive mail, and surf the internet etc, but mail just wont send!(i get the usual cannot send try later/resend options). I thought this might be an issue with my mobile broadband but have recently reinstalled it. When at home on a wireless network I have no such issues.
Any help appreciated
Charlie

Cgienke wrote:
I am not using a SMTP it is a Pop3 domain name account from freeparking and uses mail.'NAME'.com for incoming and outgoing mail!
Even though your e-mail service uses the same URL for POP3 and SMTP servers, in the software sense you actually do have separate POP3 and SMTP servers, although they may be hosted on the same machine, or the requests are routed via some "smoke and mirrors" to the right host.
It is not related to my ISP at home, which is Virgin media. My mobile broadband provider is 3. I was thinking it might be that I need to change the port settings in mail when using my mobile modem, but don't know what to change them too(or how to do it!) or configure the modem differently but again not sure what to do there!
Check with the freeparking online help to see if it supports port 587 or some such.
Also try Mail's "Connection Doctor" (under the Window menu) when you're away from home to see if that shows anything useful.
Since you can send e-mail from that SMTP server when you're at home but not when you're using your mobile broadband, I think one of two possibilities is likely: (a) Your mobile broadband provider is blocking your attempts to access the freeparking SMTP server and/or port. (b) The freeparking SMPT server for some reason doesn't like being communicated with via your mobile broadband provider. I'd check with each of them to explore these options.
Does your mobile broadband provider have an SMTP server that you can use instead of the freeparking one?
My modem(Huawei E220) is not particularly Mac friendly as it is, and I believe Mail can be quite sensitive when servers don't respond immediately?
Yes. Mail seems to have a fixed time-out value for server responses.

HT3310 Why can't I hear when using my ear plugs on my I-pad

WHy can't I hear when using my apple ear phones on my I-pad?

Make sure that they are inserted all the way into the jack. It takes a firm push to insert them all the way.

In Firefox (latest version) on Craigslist the text font is a very funky super bold angular font I can barely read. When using safari it's ok using times. is this a firefox problem?

In Firefox (latest version) on Craigslist the text font is a very funky super bold angular font I can barely read. When using safari it's ok using times. is this a firefox problem?

You can do a check for corrupted and duplicate fonts and other font issues:
*http://www.thexlab.com/faqs/multipleappsquit.html - Font Book 2.0 Help: Checking for damaged fonts
*http://www.creativetechs.com/iq/garbled_fonts_troubleshooting_guide.html

Can't print from PC using AExtreme connected printer...

Hi!
I have an AirportExtreme BS connected to my cable modem and I can connect to the internet using my PB G4 and my wife's Dell PC using Windows XP. She is using a Belkin Wireless Network Card. No problem there!
I also have a Lexmark C510 printer connected to the Airport Extreme via UBS. I can print without a problem from the PB G4 but on the Dell PC we can't even get it to recognize the Lexmark printer.
When contacted directly Lexmark said that they don't provide support for Airport Extreme, blah, blah...
Any words of advice?
Thanks!
Dennis

I suggest you follow the detailed instructions found at:
http://www.efelix.co.uk/tech/1008.html

Can't print correctly by using Adobe Reader 9.1.2

The following code in OCX is being used in my web application to print PDF directly with Adobe Reader 5.1, and it works fine!
When Adobe Reader is upgraded to 9.1.2, it no longer works. Printouts often cannot be printed correctly. However, when I add the code in red, the printouts can be printed correctly again.
Anyway, I don't want Open and Close Adobe Reader during direct printing.
Anyone knows why FilePrintSilent doesn't work? and how to solve it?
Thanks in advance!
William
    ''''''''''' Use ddeml to communicate with acrobat reader '''''''''''
    On Error GoTo ErrPrinting1
    Dim a
    Set a = CreateObject("AcroExch.Document")
    Dim lRet As Boolean
    Dim sValue As String
    sValueOpen = "[DocOpen(" & localFileName & ")]"
    sValuePrint = "[FilePrintSilent(" & localFileName & ")]"
    sValueClose = "[DocClose(" & localFileName & ")]"
    DDE_Initialize
    DDE_CreateStringHandles "acroview", "control", ""
    ' Open the conversation.
    If (g_hDDEConv = 0) Then
        g_hDDEConv = DDE_Connect
    End If
    If g_hDDEConv Then
        ' Perform the transaction.
        lRet = DdeClientTransaction(sValueOpen, Len(sValueOpen), g_hDDEConv, 0, 0, XTYP_EXECUTE, 5000, 0)
        lRet = DdeClientTransaction(sValuePrint, Len(sValuePrint), g_hDDEConv, 0, 0, XTYP_EXECUTE, 5000, 0)
        Sleep 800
        lRet = DdeClientTransaction(sValueClose, Len(sValueClose), g_hDDEConv, 0, 0, XTYP_EXECUTE, 5000, 0)
        If (lRet) Then
            Debug.Print "DDE Execute Success."
        Else
            Debug.Print "DDE Execute Failure."
        End If
    Else
        Debug.Print "DDE Connect Failure"
        printToPrinter = "DDE Connect Failure"
        Exit Function
    End If
    ' Release the memory.
    DDE_FreeStringHandles
    DDE_Uninitialize
    Set a = Nothing
    ''''''''''' end '''''''''''

We have PDF documents stored on server-side, the ActiveX control and Adobe Reader are installed on client-side.
When users open our web page, click our "Print weekly report directly" button, the ActiveX control on client will be called, and perform the above coding. It tries to download the PDF document from server to client, and pass it to the printer on client silently by using FilePrintSilent function.
The report can be printed, but not correct. It involves some unexpected characters which should be English or Traditional Chinese originally, as shown in the attached picture.
Thanks in advance!
William

Can't Print to PDF using Acrobat 8 Prof after deleting demo of v 10

Hi, I made the mistake of trying version 10 to see if it had any improvements over what I was using v 8.1.5 for, found that there were none, so I deleted it and now I can't print to PDF because it's looking for v 10. Unfortunately had to move recently and can no longer find the original disk to do a new installation. Does anyone know how to redirect the driver to the original v 8? I can open v 8 and everything else seems to work ok, just when I try to print to create a PDF it can't do it.

Thanks for the quick reply Bill! I had tried that before and tried it again. Finally got things to work by copying all the contents of my Acrobat sub-directory from the v 8 folder to the hollow v 10 folder. Now it works again! Thanks for you help and inspiration to figure this thing out. Am now a very happy camper and didn't need to tear my house appart to find the original disk!

Printing dark when using shared printer

I am having problems getting Lightroom 2 to print correctly when printing to a shared Epson 4000.
When printing to the 4000 as a local printer everything works as it should. But when I try to print to the same printer, with the same settings as a shared printer in a small network the prints turn out too dark and with colour casts.
Using epson profiles and pointing lightroom to the correct profile. Setting printer driver correctly (when i print the from photoshop CS2 it prints correctly, even when using a shared printer).
Epson 4000 using the latest 3.09 driver. OSX 10.4.10 on imac G5.
Any help appriciated, strange that everything works great on a local printer but not on the same printer when shared over the network (printersharing in OSX)
Am certain I have profile selection and printer driver settings correct ( after all it works from photoshop and locally).

Dear Larry,
Thanks for reporting the problem. You mentioned that page content is getting shifted by around 3/8 inches when printed using Mac Airprint using Acrobat which resulted in clipping of some of the content and other applications print fine.
Could you please pass on the same pdf to me as well? Although, it doesnot look dependent on any particular pdf but I would like to analyze certain behavior with the pdf you are using.
Please also confirm that you have not printed with "None" pagescaling option when you observed this.
Thansk,
Atul

Date selection will not print properly when using Microsoft Date and Time Picker Control 6.0 in Excel 2010

I have created a field input worksheet in which the user identifies start and end dates for training sessions, using the Date and Time Picker Active X Control. It works fine on-screen, but when the worksheets are printed, the dates that were selected
using the date picker calendar print out in an unreadable, huge font. The large font also appears in the print preview mode. I've tried modifying various properties in design mode, but nothing that I have tried will correct the problem.
Any ideas?

The DTPicker seems to have some bugs in it when used on a worksheet. I have overcome the above by setting the size properties to the same size as a cell and the Linked cell property to the
cell under the DTPicker. (Even setting the Linked cell had problems with an error message referring to the Check box property to be set to true so I just set it to true and inserted the linked cell and set the checkbox property back to
false.)
Then the VBA code below that Hides the DTPicker after a date is selected and unhides the DTPicker when the linked cell with the date is selected. The code is for 2 DTPickers so you will need to edit to suit your requirements.
Caveat: If the DTPicker is visible then you can't hide it by selecting the same date again. If this occurs then it is a multi step operation. First select another date and the DTPicker will hide, then click on another cell then back on the cell with
the date to unhide the DTPicker and then select the correct date.
Hope it helps and feel free to get back to me with any questions etc.
Private Sub DTPicker1_Change()
    Me.DTPicker1.Visible = False
End Sub
Private Sub DTPicker2_Change()
    Me.DTPicker2.Visible = False
End Sub
Private Sub Worksheet_SelectionChange(ByVal Target As Range)
    Select Case Target.Address
        Case "$E$5"     'This is the linked cell for DTPicker1
            Me.DTPicker1.Visible = True
        Case "$E$13"    'This is the linked cell for DTPicker2
            Me.DTPicker2.Visible = True
    End Select
End Sub
Regards, OssieMac

Can't print duplex when using a CS2 doc in CS3

Similar Messages

Maybe you are looking for