Can't Print TO HP All-In-One

I have moved my HP printer from the USB connection on my iMac and plugged it into the USB port on the Airport Extreme Base Station.
I can't print to it. Help please.

Which HP printer do you have?
This may work.
Use the process outlined here:
HP Printers (and others) not on compatibility list and Airport Extreme Printing
http://tech.ifelix.net/1300.html
Using the Gimp-Print drivers for the HP PhotoSmart P1000 printer.
iFelix

Similar Messages

Can't print to 8600 All-In-One after awhile

I have an 8600 All-In-One N911A and it is connected to my network via wired Ethernet and after power up, I can print to the printer via my Mac's and ipad/iphone no problem. After some preiod of time (hours) none of my devices can print to the printer however I CAN get to it via a web browser by IP Address.
I get the message printer is not responding or looking for printer and if I power cycle the device it can be seen/printed to again but the issue repeats itself after a few hours.
Any clue what could be casuing this with all my devices? My main router is a fairly new Linksys Router/Wireless/Switch and it seems like a printer. I had a similar problem with an 8500 which I replaced thinking it had a networking hardware failure so I don't think it is a bad printer given this is the second one with a problem.

Hi checkyou,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
Sorry to hear that you are having connectivity issues with the printer to the WiFi. I have seen this issue and I was able to resolve the issue by doing one easy step. If you happen to have the printer power cable connected to a power bar/strip, please remove it and connect it directly to a wall outlet. HP printers already have built in surge protector and if you have the power cable connected to a bar/strip, the printer will not get all the power it needs to function properly and this could very well be the reason why you are having issues.
Here is a document that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
Please note that the printer that is listed in the document is a LaserJet printer and it is only used as an example. This document is meant for HP products in general.
If this does not resolve the issue, please feel free to write me back.
Thank you for your time.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Can't Print in C6280 all in one

A few days ago I tried to print out a map and directions from mapquest. It's about 1.3 mb. It wouldn't print and I'm unable to delete it. The choices I'm given are pause, resume, cancel, restart and properties. I've tried them all to no avail. Now I can't print anything except a test page. What do I do?
Thank you!

1. You are up to date with drivers, yes?
2. Can you provide an example?
3. If the coupon is displayed on screen can you print the whole page instead of clicking a print link?

Can'[t print on C3150 - All-in-one

I can print from any other program, test page etc... but not from ID CS3 or from Acrobat (a pdf made in CS3), pulls paper in as if to print, then nothing else... I've tried all settings I think. Any ideas, or where to go for help. I called this a LJ3150 in previous post, can understand why nobody answered... Thanks L W I'm on an XP SP2, Desktop, printer is on USB port.

Just a thought, have you got spooling turned on in the printer properties? If so, turn it off.
Go to Printers folder, select it and change the defaults.

Can't print on my all-in-one 6413 two consecutive prints.

The printer is connected to a wireless router with a network cable.
I'm printing from a Windows 7 laptop connected wirelessly to the router, no security key only MAC address.
No problems when surfing.
Every time I send a print or more than one I have to troubleshoot the printer, even when the first print comes OK the second attempt fails and I need to troubleshoot again, turn off/on the printer etc.
Removed and reinstalled driver using the latest version on the internet without luck.
Installed it as a network printer.
After initial install the test page comes out just fine, no problems whatsoever.
Although it supports wireless printing I'm using it as a network printer not a wireless connection.
Any idea what may cause this? Why the initial setting is not saved?
This question was solved.
View Solution.

Hi adi7ch,
Ok, Let me know what you find out?
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"

Printing with HP all-in-one connected to Airport Extreme with USB

We have an HP Photosmart 2610 all-in-one, an AirPort Extreme base station, and a G-5 MacIntosh running OS 10.4.8. We can print when the all-in-one unit is connected directly to the Mac with USB cable, however, we are unable to print when the USB cable is connected to the base station. What can you suggest?

Which driver are you using?
According to HP must use drivers 6.3.4 or 7.0
http://h10025.www1.hp.com/ewfrf/wc/genericDocument?lc=en&cc=us&docname=c00035369

HP Printer Assistant (3510e All-In-One) Display No Maintenance Option

Hello.
I have a problem with my HP printer (a little over a year old - expected to work well)
Desktop PC: HP Pavillion HPE310t 64-bit (OS: Windows 7 Professional)
Printer: HP 3510e All-In-One (Wirelessly Connected & Confirmed by the "Green -Colored Check Mark")
Problem:
Expected: HP Printer Icon which, upon being clicked on it, displays a message "Retrieving information from the device" before displaying the HP printer assistant where it displays eight options including "maintain your printer".
Current Condition: only displays "Printer Setup & Software" which is part of the printer setup process. Because of this, there is no way to access the maintenance option as I am in need now.
Yes, I tried to reinstall the printer software, after completely removing all the existing files, using the software CD that came with the printer - no avail. Repeated the process twice to see the same result.
What is the problem and how can it be fixed?
I would greatly appreciate to have your help.

Hello greenjewel,
Welcome to the HP Forums.
I see that not all the options are available like they once were.
I suggest that we start off by running the HP Print and Scan Doctor.
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thanks for your time.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Computer is unable to communicate with printer Officejet J4680c All in One using wireless setting.

I received a message while I reinstalling software and driver to change from usb conection to wireless conection: Your laptop is unable to communicate with your printer (Officejet J4680c All in One. This may be caused by firewall software. If you are using firewall software, verify that UDP port is unblocked for both inbound and outbound trafic. But I don't know how to verify that option in my computer. While I reinstalled software I turn off firewall software in my computer. Can some one help me to resolve this issue? Thanks.
Ref: My laptop is Toshiba Satellite P755 with Windows 7 (64bit)

Hi,
Download and run HP Printer Install Wizard from link below
www.hp.com/go/tools
Although I am an HP employee, I am speaking for myself and not for HP.
--Say "Thanks" by clicking the Kudos Star in the post that helped you.
--Please mark the post that solves your problem as "Accepted Solution"

Printing issue wirlesse printing on c5100 all in one

Hello
I have issues printing over my wirless network using a mac and printing on C5100 all in one. When the printer is running and I start up my mac (running 10.8.3) I can print the windows documents. However if the printer is switched on after the mac is switched on it can not find the printer.
I reinstalled the all the drivers on the mac and set a fixrd ip adress for the printer but both doesnt work. same issue with a second mac laptop also running 10.8.3
Anybody an idea what this could be?
Tahnks in advance

I am thinking the router does not support Bonjour (otherwise known as mDNS). Macs need this service to be able to find the printer.
Get into the router settings and look for Bonjour or mDNS and make sure it is enabled. Also, make sure the multicasting is enabled in the router.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

How can i print logo in all the page

i've created a form(SAP script) which have five page.pls can anybody tell me how can i print logo in all the five page?

hi,
u can try this in
windows
change window type as CONST or MAIN.
cheers,
sam

I have a iphone 5c and a wireless computer hooked to a usb wireless printer Hp4215 officejet all-in-one how can I print from my phone to the printer

How can I print to my wireless Hp officejet 4215 all-in-one printer that is usb in line with my computer that uses windows 7 from my Iphone 5c

there are 2 ½ ways to print
1. the printer support AirPrint and it works out of the box
2. one get a printing app from app store which support the printer
2-½ one get the free software from netgear called netgear genie which will make the computer display all printes it's know act as AirPrint printers
no other things in the known universe will make printing possible

Can't setup wireless printing : HP4385 Photosmart All-In-One Printer / Linksys Router/Mac OS 10.5

I am attempting to set up my printer to operate wirelessly. I have the computer and printer connected via USB for the setup.
I have :
PRINTER : HP All In One Photosmart C4385
ROUTER : Linksys wireless B (WPA security)
COMPUTER : Macbook Mac OS 10.5.8 notebook.
I've downloaded the correct HP software.
On the printer, the wireless radio is set to "on"
PROBLEM : Using the HP Setup Assistant, I select my Wi-Fi network, and get an error message " the selected Wi-Fi network is not within reach of the device"
The printer and router are in the same room with nothing blocking them.
Print out of HP Network Configuration Page :
General Information
Network Status : Offline
Active Connection Type : None
URL : http://0.0.0.0.0
Firmware Revision : WPxxFN0723AR
Hostname : HP8766D2
Serial Number: CN7CDD51P80509
Admin Password : Not Set
802.11 Wireless
Hardware Address (Mac) : 001e0b8766d2
Status : Disconnected
mDNS
Status : Enabled
Service Name : Photosmart C4380 series [8766D2]
SLP
Status : Enabled
Any help greatly appreciated !

Print a WIreless Network Test from the front of the printer. It will self-test the printer's radio.
Can you give me the exact model number of your router? If it is a 802.11b router, it may be time for a new one. If it is, are you sure you are using WPA and not WEP?
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Setup can't detect network printer Photosmart C7250 all in one

I volunteer for our local historical society. The person who did a lot of the computer maintenance work is not active at this time so I’ve begun to look at things.
There is a Gateway PC running Windows 7 64 bit home premium, a Sony Vio laptop running Vista 32 bit home premium, an HP Laser printer and (of most importance here) an HP Photosmart C7250 All in one printer.
Internet connectivity is via a dsl line with a combination modem/router. I think the modem/router is a Westell or an Actiontec through Frontier Communications (formerly Verizon in this area) but I’m not sure and I’m not at the museum now.
A couple of weeks ago I was able to connect the laptop to the network via wifi. My next step is to connect the laptop wirelessly to the printer so we can print wirelessly over the network. The printer was originally set up through a usb connection so I changed it to a wired Ethernet connection. The PC now successfully prints to the printer over the network. I downloaded the software and drivers directly to the laptop from the HP site and began the installation. When it got to the point of finding the network printer the software couldn’t detect it. I then put in the ip address for the printer (from the network info printed out from the printer) and it still couldn’t find it.
This same situation occurred when I tried to set it up on my personal laptop (Win7 , 64 bit) as well. Setup couldn’t detect the network printer, even after searching for the network ip address.
Since the printer is connected to the network (router) via an Ethernet cable, I don’t have the wifi radio turned on in the printer. This shouldn’t make any difference.
I’ve searched the forums and haven’t seen anything that is like my issue.
I don’t what else to do. Hopefully someone will give me some advice on what to do next.

Download and run this utility: http://h20180.www2.hp.com/apps/Nav?h_pagetype=s-926&h_lang=en&h_client=s-h-e17-1&h_keyword=dg-NDU&ju...
What does it say?
If the network has Wireless Isolation turned on it will prevent wired devices from seeing wireless devices. Do you have access to the router?
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Can't detect or print to C8189A All-in-One-Printer on a wired LAN

Computers on my home wired LAN repeatedly but intermittently stop being able to print to the HP C8189A printer attached via wired LAN connection. I began trouble shooting last night and uninstalled all HP software to start afresh.
I cannot print to my HP C8189A all-in-one printer conected to a wired network from my desktop PC running Windows XP with SP3. I can see the printer has pulled an IP from the router by looking at the router's attached client list. I can ping the printer at its assigned LAN IP address.
My desktop pc and the C8189A printer share a common DLINK Gigabit Switch which connects wired wired LAN to the DLINK router.
I uninstalled and reinstalled all HP software but during the HP Solutions Center software reinstall it could not find the PRINTER on the lan, even when inserting the Printer's assigned IP address.
When checking the network configuration from the printer, it confirms that it is has the correct IP address, but the HP software still cannot detect it. I have pulled the power connector from the back of the power a couple times to RESET the printer. This usually corrects what is now a terribly frustrating problem accessing the printer.
Additional factoids: 1) other PCs can print to this printer, 2) SPYBOT Search & Destroy is running on my PC and popped some registry change windows during the install.
I'm running out of ideas - any suggestions please?
Message Edited by VARocketry on 01-09-2009 11:54 AM

Hmmm ... this is interesting. In review:
You can print intermittently from your XP SP3 box to the OJP L7680.
Disabling the SW firewall (Norton/Symantec, Zonealarm, McAfee, etc) on the SP3 PC doesn't help.
Other computers on your network have no problems printing to the OJP L7680.
You are running a wired (Ethernet) network.
Did I get this right? I'd like to ask a few more questions:
What are the other types of computers on your network and what firewall do they run?
The next time your XP SP3 computer has trouble printing to the OJP L7680, try to access the printer's internal web page.
What are the IP addresses of the other devices on your network? By chance, is there a duplicate address on your network?
Finally, you can try adding the print driver manually to see if we can get you printing. This is the sequence for XP:
Click "Start" button --> Printers and Faxes.
Under Printer Tasks, click "Add Printer".
Click "Next" button on the first Add Printer Wizard window.
If the option for Local or Network printer appears, select "Local printer attached to this computer" and deselect the "Automatically detect and install My Plug and play printer" option. Click "Next".
Under Select a Printer Port option, select "Create a new port" and select "Standard TCP/IP Port" and click "Next" button.
In the "Welcome to the Add Standard TCP/IP printer port wizard" make sure that the printer is turned on and configured. Click "Next" button.
Under "Add Standard TCP/IP Printer Port" enter the printer's host name (that is the hostname of printer that printed in network configuration page)
under "Additional Port Information" select "Standard". Click Next, and then click Finish.
Now, select HP from the list of manufacturers, select your printer from the list of Printer models and click 'Next' button.
The Printer name will be highlighted on the next window.
Click "Next" button.
It ask for the Printer name -- leave it as is.
Select "Yes" option for making the printer default.
Click "Next" button.
The Printer Sharing dialog box will open.
Click "Next" button.
The Print Test Page box appears.
Select "Yes" option to print a test page.
Print Test Page.
Completing the Add Printer Wizard box appears.
Click "Finish" button and wait for the files to copy
This should work to get you a print queue for your XP box.
Regards / Jim B
Regards / Jim B / Wireless Enthusiasts
( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
+ Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

Can't scan from 5610 all in one front panel

I have an HP5610 all in one installed on my Dell Vostro 200 with E6550 dual core processor, XP SP3 home OS. I noticed the problem when I tried to scan from the front panel of my 5610 and the orange exclamation light started blinking. The display said "No Scan Options". I ran the HP Print and Scan Doctor and it said to set the front panel scan destinations. I selected the default settings and closed the HP Direc.exe. When I opened the HP Direc.exe and looked for the panel destination that I set, I saw that they did not save. I can scan just fine using the HP software and have been doing so for many years. I now am wondering if I have had this issue all along, especially since I never remember trying to scan from the front panel of my 5610 until the other day.
I have done just about everything the Printing and Scan Doctor told me to do. I have shut down my 5610, unplugged it for several minutes, plugged it back in, removed the all in one program and reinstalled from the HP website. What is strange...I have the 5610 software installed on a Dell 3000 Dimension I have in a home network and it works perfectly. I'm seriously thinking about moving the 5610 in the room with my Dimension 3000 and buying a (print only) printer for my Vostro 200. I can work around this but I can't stand to have something not work correctly with a very good computer. Please, no comments on my preferred operating system. I am not upgrading, and as I said, this all in one works perfectly with a PC built in 2004. And contrary to belief, I am still getting security updates on a biweekly basis from Microsoft. One day last week I got 8 in one day. Thanks all for all of your excellent help!
Buzbo

Hi @buzbo,
Welcome to the HP Forums!
I noticed that you cannot scan from your HP Officejet 5610 all in one front panel to your WIndows XP computer. I am happy to help you with your scanning concerns!
Please see the following guides:
A 'No Scan Options' or 'Scan settings are not set' Message Displays for HP All-in-One Printers When ....
An 'An error occurred while communicating with scanning device' or a 'There is no computer connectio....
Hope these guides are helpful, and have a good day!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Can't Print TO HP All-In-One

Similar Messages

Maybe you are looking for