Can't re-install XS key drivers

Hi
I am unable to re-install Logic 6 now that Logic 8 is onboard. During installation, as soon as the XS key drivers are being installed, it stops with a 'try again' prompt. As instructed, my XS key is not connected during installation.
I wouldn't be bothering if it wasn't that some old songs won't open in 8.
Any ideas would be appreciated.
Thanks

Connect the XSkey, and launch System Profiler. Does system profiler recognise the XSkey on the USB bus?
If not, either your XSkey or USB bus is defective.

Similar Messages

HT201413 How can I download & install Apple iPad drivers? PC says iPad is 'unknown' device and the ipad fails to sync w/iturnes.

How can I download & install the correct Apple iPad2 driver for Windows Vista?
I installed iTunes, but cannot sync with iPad. PC says iPad is an 'unknown' device' and it is not recognized by iTunes.
Thanks for any help.

Device Not Recognised > http://support.apple.com/kb/TS1538

Windows 7 x64 can't read/install any printer drivers from Windows Server 2003 x64 (AMD64 folder and HP Deskjet 855c)

I read the thread Widows 7 printer
HP deskjet 855c driver about possible installation of HP855c drivers onto Windows 7 x64 from "Windows Server 2003 x64" CD but I didn't have enough luck to succeed with doing it on my laptop. That thread appears to be dead now
as it is marked "Answered", so I'm asking for help here. I have Toshiba Satellite P500 with Windows 7 Home Premium 64-bit (http://i55.tinypic.com/2zgth6v.jpg).
Let me tell you first that I don't have access to Windows Server 2003 x64 or XP Pro 64 CD's. However I did some research online, which eventually forced me to learn about the "file sharing". After extensive search I was able to get the copies
of AMD64 folders from Windows Server 2003 R2 Standard x64 with SP2 and
XP Pro 64. The reason that I went also after XP Pro was because I thought that the extra wording "R2 Standard x64 with SP2" in description of "Windows Server 2003" did not reflect the exact name provided by poster
Alan. I couldn't find just "Windows Server 2003 x64" (does it matter?).
Anyway, I followed first the drill with running "printui /s /t2" and disabling UAC, and then in both cases I was able to locate the
NTPRINT.INF file (http://oi51.tinypic.com/9qwvt2.jpg - this image is from XP Pro AMD64 folder) but each time when I
attempted to install the driver, I got the same message stating:
"The folder you specified doesn't contain a compatible software drive for your device. If the folder contains the driver, make sure it's designed to work with Windows for x64-based systems." (http://oi53.tinypic.com/27yveiw.jpg)
Why aren't there x64 drivers?
During several installation attempts I had the printer connected to or disconnected from my laptop. It didn't make any difference. I must add that for this purpose I had to use different cable than the original one designated only for the
Parallel port in my old desktop with Windows XP. My new laptop with Windows 7 x64 came only with 3 USB ports (plus 1 HDMI and 1 Serial). Because of that situation I bought in advance a new printer cable called “USB to 36-pin Parallel Port Adapter
Cable” (http://www.amazon.com/gp/product/B003A8I75E). I'm not sure, if it will work until I can install the printer.
Besides, nobody talked about this issue yet. I was also playing with the port choices in "Add printer" step; changing from default LPT1 to USB001 with the same negative results.
I don't know what I'm doing wrong. I was very hopeful after reading positive "case closed" notes there.
Can anyone help me here, maybe by making the necessary files available for download? I'm willing to pay for such assistance or make a donation, if necessary. Seriously. Judging by the large number of views of the original
thread, one could assume that there is a potential demand for such service. It would be more human to pay few bucks for a few driver files than $900 for the whole Windows Server 2003 x64 CD, no? Can Microsoft accomodate me/us, please? :)
Andrew*
P.S. I was advised to come for help here from
http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/windows-7-x64-cant-readinstall-any-printer-drivers/4e7d06e1-33a5-4597-be70-4fdc087a63a7?msgId=9a045994-0d31-4d40-b17d-dba372393ee4

I have my HP 855c/driver working on Win 7 Ultimate x64. I used the 'printui /s' procedure and 4 files described above with some minor changes.
I pulled WindowsServer2003.WindowsXP-KB914961-SP2-x64-ENU.exe down from the Microsoft website. Running the file causes the exe to unpack into a temp folder at the root drive. A 'Setup Error' message box is displayed once the file is run. I left this
message box up until I copied ntprint.inf, ntprint.cat, and sp2.cab from the temp folder.
I copied driver.cab from a Windows XP Pro disc. I also needed amd64\stdnames.gpd which was already in my Windows 7 c:\windows\system32\spool\drivers\x64\3 folder.
I created a folder with the 5 files (ntprint.inf, ntprint.cat, sp2.cab, driver.cab, and amd64\stdnames.gpd). This is my 'Have Disc' folder.
I followed the 'printui /s' instructions, first changing the permissions mentioned above and then installing the driver. Next I followed the instructions to add a printer from Control Panel 'Devices and Printers' - 'Add Printer', choosing to 'use an existing
driver' when installing the HP 855c.
I used a slightly different ntprint.inf, size 1570418. The readable contents of ntprint.inf is as follows. Notice the line 'CatalogFile=ntprint.cat' is not included. I tried using the 1570468 version of ntprint.inf; when I did I received an incompatibility
message (probably the same one mentioned above).
; NTPRINT.INF (for Windows Server 2003 family)
; List of supported printers, manufacturers
[Version]
Signature="$Windows NT$"
Provider=%MS%
; LayoutFile=layout.inf
ClassGUID={4D36E979-E325-11CE-BFC1-08002BE10318}
Class=Printer
DriverVer=10/01/2002,5.2.3790.4533
[ClassInstall32.NT]
AddReg=printer_class_addreg
[printer_class_addreg]
HKR,,,,%PrinterClassName%
HKR,,Icon,,"-4"
HKR,,Installer32,,"ntprint.dll,ClassInstall32"
HKR,,NoDisplayClass,,1
HKR,,EnumPropPages32,,"printui.dll,PrinterPropPageProvider"
Good luck

[HELP] I can't install the bootcamp drivers on my mac.

Hello people.
I have a problem and i wish if you could help me with.
I have an iMac Early-2009 ( 2.66ghz C2D / 4GB 1333mhz RAM / GeForce 9400 256mb ) with Mountain Lion 10.8.4
The problem is that, i can't install the drivers from the bootcamp app ( the one from the bootcamp itself app, where you need a USB to download it)
i've already partitioned the HDD, and installed succesfully a Windows 7 Ultimate 64bit.
But there's one little issue, when i try install the drivers i downloaded before on my USB, it says that "Bootcamp x64 is unsupported on this computer model".
BUT, what? i've installed correctly the Windows 7 64bit on the iMac.
I can't install anything, but only graphics driver. ( manually)
I searched in every forum trying to resolve my problem, i've read that you can install it from de DVD with Snow Leopard that came with the computer
but that disk is broken; it's annoying because it seems that is the only solution , with that resulting on a dead end.
I could install my NVIDIA drivers, using the ones from bootcamp drivers, BUT USING THE WIN_32 version because the WIN_64 was unsupported by my machine. ok, i could install the drivers and was the 263.03 i think.
Now i want to upgrade to my lastest drivers ( 320.14 WQHL ) and says that can't detect my gpu. but the old driver that came with recognized it with no problems. I tried also auto detect GPU, and the same drivers but no result.
Anyway, the main problem is that is "Bootcamp x64 is unsupported on this computer model". with a Windows 7 64bit copy installed on the bootcamp partition. this is ******* me off
I sucessfully installed on my Macbook Pro Late 2008 ( C2D 2.06ghz / 8 GB RAM / 9600m GT ) and everything fine, a Windows 7 64bit. installed the drivers and everything fine, even accepted the lastest drivers (320.14 WQHL) from nvidia. but that was on Mountain Lion 10.8
but since 10.8.3 only lets you install only 64bit, i can't search for a copy of win32bit and install it because, it's going to be the same problem anyways.
So if you could help me out with this *** problem.

I have an iMac (24-inch, Early 2008) — iMac8,1 and I have exactly the same issue. Now, I'm running Mavericks, unfortunately.
On the one hand, from http://support.apple.com/kb/HT3986, I see:
"Do all Intel-based Macs support Windows 7?
All Intel-based Macs support Windows 7 using Boot Camp 3.1 or later except these:
iMac (17-inch, Early 2006)
iMac (17-inch, Late 2006)
iMac (20-inch, Early 2006)
iMac (20-inch, Late 2006)
MacBook Pro (15-inch, Early 2006)
MacBook Pro (17-inch, Late 2006)
MacBook Pro (15-inch, Late 2006)
MacBook Pro (17-inch, Early 2006)
Mac Pro (Mid 2006, Intel Xeon Dual-core 2.66GHz or 3GHz)"
So, I should be good.
However, from http://support.apple.com/kb/HT5634, my iMac is not supported in Boot Camp requirements, which would have been nice to know before I purchased a copy of Windows 7. I cannot get the Windows drivers to download from Boot Camp, and when I download them manually, whether version 4 or 5, I get the "Bootcamp x64 is unsupported on this computer model" message, which makes the HT3986 information unhelpful. I even tried a Snow Leopard CD while in Windows, and it gave me the same message. I tried one of the 3.x Bootcamp files, and still no good.
The funny thing is, I ran Bootcamp to create the partition for Windows 7, and it even popped up a message stating that Windows 7 was the latest Windows I could install on that machine, and the installation went fine. However, I am missing who knows what drivers, etc, because Apple won't provide the Windows support software for a machine that evidently can run the software. The graphics drivers appear to be fine, as the aspect ratio corrected itself, something that didn't happen on my MBP without having the Windows Bootcamp software. I also have wi-fi, which is better than some experience.
I even cannot get the little Boot Camp Windows icon/software that should be accessible in the system tray, so I can set preferred system to boot in, tell it to boot into OS X, etc. So, for that, I would have to rely on rebooting while holding down the ALT key, and my non-Apple keyboard for some reason won't do that (but that's another subject).
I guess there is nothing to do other than just do everything manually, piece by piece, unless someone has a solution that is eluding me.

Yours sincerely! I just bought a Sony DCR-SD1000 camera only when installing the cd drivers not supported by the operating system Machintosh. I've contacted the seller said the store did not provide for the apple os. How can I move all the files on the ca

Yours sincerely! I just bought a Sony DCR-SD1000 camera only when installing the cd drivers not supported by the operating system Machintosh. I've contacted the seller said the store did not provide for the apple os. How can I move all the files on the camera the port out is to use a USB data cable to a laptop for my macbookpro can not read the contents of the file and the camera. I also want to use the lens on the camera as a substitute for the embedded camera on my macbookpro, what should I do to replace the embedded camera on macbookpro with sony camera so that the camera could be more variety and can I record when I turned macbookpro . Please help for this so that I can quickly capture the results from sony camera to my macbookpro. Thank you.

See this page http://macosx.com/forums/networking-compatibility/296947-sony-camcorder-my-mac.h tml - might be some helpful tips there.
Clinton

I'm installing windows 8 64 from iso dvd-I did the partition wiht BCamp 5 and I did the usb with compatibility software-once installation start from dvd, it ask me for some disk, usb or dvd drivers to continue. How I can continue the instalation?

I'm installing windows 8 64 from iso dvd-I did the partition wiht BCamp 5.
I did the usb drive with the compatibility software-once installation start from the dvd, it ask me for some disk, usb or dvd drivers to continue.
How I can continue the instalation? How I can provide those driver to the instalation process?
Thanks
Manuel

You can't get there with GUID/GPT.
There are tips on making a USB flash device that is bootable.
You can set aside a small 6GB partition somewhere and put Windows 7 installer there and run it WHILE IN Windows.
Windows Vista can be upgraded in place to 7 RC.
You'll need NTFS (30-50GB).
Windows doesn't support FW for booting.
You can create a drive that has Master Boot Record.

Hi, recently i bought macbook pro with retina display and installed windows 8 professional original software also. but in windows 8 track pad is not working properly. can you help me with providing drivers for trackpad to work on windows 8 professional .

hi, recently i bought macbook pro with retina display and installed windows 8 professional original software also. but in windows 8 track pad/ TOUCHPAD is not working properly. can you help me with providing drivers for trackpad to work on windows 8 professional .

Did you download and install the Windows Support software? If you did, did you use the Boot Camp Control icon to set up the trackpad how you want it?
http://www.apple.com/support/bootcamp/
https://discussions.apple.com/community/windows_software/boot_camp

Boot camp 4 can't install windows support drivers

Hi everyone,
I have the new imac 27" with thunderbolt and preinstalled Lion. They dont give you a CD.
I run Boot Camp assistant (version 4.0) and try to install windows on a purchased DVD Windows 7 x64 ( i am a recent convert to mac but still need some windows proggys.)
Ok so once I run the installation It asks me to download the windows support drivers... I do this but then it stops 3/4 through the process and comes up with an error "can't install windows support drivers".
Do any of you out know how to fix this???
Also If I dont use the option to update the software before installing and just select install windows 7 (second option) from a disc. It installs windows fine BUT it wont install any of the network, usb, camera, graphics and sound drivers. so basicaly I am blocked from the internet for windows to update the drivers. I also cant get the driver files from another computer as the mac in windows mode can recognised usb sticks as the drivers arent installed.
I need help urgently on this as it is doing my head
Thanks in advance.
Daniel!

Yes, but.
Open Network Preferences>Network>Advanced>Proxies and uncheck everything (try Passive Mode on, and off, but no auto Proxies)
And try again.

I have Adobe LiveCycle installed on my computer, and I am upgrading my computer, how do I install LiveCycle on my new computer so I can enter in my product key?

I have Adobe LiveCycle installed on my computer, and I am upgrading my computer, how do I install LiveCycle on my new computer so I can enter in my product key?

Live Cycle installation doesn't require any product key.

Can't install Boot Camp drivers on Early 2010 MBP

Hello there, so I'm having a problem installing drivers as you can see from the title. I was trying to create a Boot Camp partition on my girlfriend's MBP. She has the 2010 early one. Now we got windows installed on there with no problem; however, we can't seem to get the drivers that allow her speakers, webcam, etc. to work.
Initially we tried using my Snow Leoperd OSX disc because as far as I know she has snow leoperd too and she can't find her original OSX disc. I have an early 2011 MBP so when I tried using the boot camp drivers on my OSX disc it would not work. It said the drivers on mine weren't made for hers. Whatever no biggies, so I google an alternative and tried to download the drivers from boot camp manager back on her Mac Partition. It said that the drivers could not be found or could not be downloaded. Something to that effect. So now that we can't download the drivers, or use the original disc, what other options do we have?

Hello Arroyo1291,
Welcome to Apple Support Communities! Given your situation I strongly recommend you to call Apple Care support at 1-800-275-2273. When you get in touch with an AppleCare representative, ask them for a replacement Mac OS X install DVD (I think Apple calls them Fullfillment Disks). Give the representative your girlfriend's MacBook Pro serial number and tell them that the Mac OS X installation DVD that came with her computer is now missing and that you want a replacement DVD. Also, make sure to ask them if the replacement Mac OS X install DVD contains the Windows Bootcamp Drivers on it like the original Mac OS X Install DVD that shipped with your girlfriend's MacBook Pro.
One last thing, if your girlfriend's MacBook Pro is not under the AppleCare extended warranty, they may charge you a nominal fee on the replacement disc order.
Best of luck!

Can't install boot camp drivers on my windown vista

Hello
First:-
I would like to say thanks to all of the members how helped me with allot of issues.
Second:-
I'm having a problem while installing boot camp drivers on my vista with using the Leopard disc, it always stop installing and gives me a message about sufficient privilege then i have to choose between these choices (Abort-retry-ignore)
please guys how i can solve this problem??

Well i did the same thing but i lost so many functions, such as:-
1_ Volume controller on my keyboard is not working.
2_ I cant switch to my macintosh unless if i restart and insert the leopard disc to open the startup disc and let me choose the way i want my computer to reboot.
3_ isight is not working.
4_ Bluetooth is not working.
and so many stuff.
i hope that there is another way like giving it the permission or something like that?
please guys is there a way to solve this issue?

How to install all the drivers for the MacBook with Windows 7 or 8 without the disk from OSX Lion? Where can I find the drivers?

Guys, a have one big problem..My customer brought me a macbook with windows 7 installed to do a format and reinstallation, but she is no longer the OSX Lion, and do not know how to install the sound drivers, "touchpad", among other drivers, how to solve this? Where can I find the drivers? The MacBook is now with Windows 8 installed.

Sorry my bad english..
See is meant. The MacBook has already come for me with Windows 7 installed, checked that it does not have another partition with OSX Lion installed, do not know how the person who did the maintenance before I managed to remove the partition with the Lion, so I can not create a disk or access boot camp because there is no partition Lion and don't own the DVDs of OSX Lion, you understand me?
There is a boot camp Windows executable? Where do I find, since I poked around and found nothing on ...
The sound driver is installed, but not working ... and the rest are missing there also, the trackpad also does not work correctly, the right button does not work ... My experience with mac is low, it may be that you do not know how it works correctly the trackpad

When i click on itunes to open, message says: the registry settings used by the itune drivers for importing and burning cds and dvds are missing. this can result from installing other cd burning software. Reinstall itunes. I'm inexperienced. Please help

When I click on itunes, I get a message that says, "the registry settings used by the itune drivers for importing and burning cds and dvds are missing. this can result from installing other cd burning software. Reinstall itunes." I am a really inexperienced computer user. My computer is a windows 7. Would someone please walk me through this or tell me where to find information on how to do this. Thanking in advance, Laurie

Check out this Apple article -> iTunes for Windows: "Registry settings" warning when opening iTunes
The article will walk you through reinstalling iTunes and then checking for or creating device filters. Did it help? Did you run into any problems?

I have purchased Lightroom 5 and had it installed but I had to replace my matchbook pro and now I can't find the activation key - is there a way I can get it emailed to me or how do I find it? Most other plugin's email out the activation key so you have a

I have purchased Lightroom 5 and had it installed but I had to replace my matchbook pro and now I can't find the activation key - is there a way I can get it emailed to me or how do I find it? Most other plugin's email out the activation key so you have a copy but I have seen no way to get it.

If you registered your Lightroom with Adobe after you installed it, you can log into your Adobe account and get your serial number from your account.

Can I install camera raw drivers for a Canon 1D X in Photoshop CS4 Windows7 64bit

Can I install camera raw drivers for a Canon 1D X in a Photoshop CS4 Windows 7 64bit system

you need cr 6.7 or better.
ps cs4 can only update to 5.7
you can either use the dng converter,
Win
Mac
or upgrade your ps, Lightroom and Photoshop | Adobe Creative Cloud Photography Plan

Can't re-install XS key drivers

Similar Messages

Maybe you are looking for