Can't reach 133 fsb

I have been struggeling with this problem for a while. I´ve tried to replace my memory modules and I´ve also replaced my graficscard but it still didn't work.
My system runs perfectly fine in 100 fsb but when I turn it up to 133 it just passes the ide-drivetest then it shuts down. The only thing I can think of is that the psu cant handle the load when it´s in 133 fsb.
Note: I have been able to run the fsb at 133 earlier.I decided to upgrade my system on some weak spots and now it simply doesn´t work anymore.
Here´s the list of changes:
Added memory (512)
Replaced GF mx460 with Ti 4200 (didn´t keep the mx)
BIOS flash for faster cpu-support (haven´t bought new one yet since my old cpu doesn´t work properly).
My question is therefor if it is possible that this small change could cause the powersupplie to cut?
My second question is how much powerI need if I´d replace gpu and cpu with faster/better once, for an example GFFX 5600 Ultra and a AthlonXP 2400+ ?
Third question: Where can I find a list of psu-manufactures that provide the correct figures? (There must be more than one).
MSI KT3 Ultra-Aru
Athlon XP2100+
1x256 crucial pc2700
1x512 crucial pc2700
Asus GF4 Ti4200
2xMaxtor Dimondplus9 80Gb Raid1
Cheiftech 340W psu (standard psu)
Thanks for your this great forum:)

Tell about Amps. P.S. gives to 3.3v. 5v. and 12v. Try with only one memory module. You must have in mind that you are using Crucial memory and I have read toooo many posts of guys having problems on their PC and are also using Crucial mem.   8)

Similar Messages

  • KT4V Problems with 133 FSB

    I've got a question about this board. The version I have is an OEM board, I have 1 major problem with it I have tried EVERYTHING i have read in the forums about it and nothing works. I can not get the board to run at the 133 FSB i have a AMD Tbird 1.33Ghz chip with the 266 FSB If i set my Bios to 130 FSB i can run at 1300 Mhz fine but when i go to 133FSB it just sits there and loops the Starting XP screen Here are my sys specs
    AMD 1.33 Tbird
    Thermaltake Valcano 7+ Running on the higest fan speed.
    MSI KT4V Mainboard
    PNY Geforce 4 Ti4200 8X Agp card
    600W Powersupply Robertron I believe
    1 60 Gig Maxtor HD
    1 60 Gig Samsung HD
    1 Aopen 20x CDRW Drive
    1 Stick of Kingston PC2100 256 DDR ram
    1 Stick of IBM PC2100 256 DDR ram
    I have tried it with each stick alone and each stick in different places everytime
    I am Running Windows XP Pro SP1 Installed and useing all the latest Drivers for the Vid, Built in Lan and Audio. Also the Latest Bios update 1.7 nothing seems to make this board run at 133FSB Any help would be greatly thanked.

    OK now I know its not my Heatsink or anything else on my system I know it is this board. I removed Everything execpt 1 hard drive put a old 4 meg PCI video card in and REmounted my HS and CPU and it took me 5 reboots just to get the board to post, after that i set it to the proper 133 FSB and got a NTDRL error changed it back to 100 FSB and it frooze 3 times before finally working After this experence I will Diffently NEVER buy a MSI board this board has been nothing but a headache from the start I will stick by my old faithful ABIT from this day foward..... Anyone wanna buy a slightly used MSI KT4V ??  :D

  • Why is that my pentium 2.66 only have a 133 fsb in the bios setting

    please educate me i cant figure out why is that in the bios core cell menu on my 915P Neo2 Platinum (1.0b) pentium 4 2.66 fsb 800 only displays a 133 fsb but i can see the processor runs correctly at 2667 with multiplier of 20. is this means the pentium 4 in the FSB category is only like a pentium3 with only a 133 fsb with a jacked up multiplier? 
    how to figure out the pentium 4's 800 FSB because i cant see it in the bios
    unlike an AMD with a 400 FSB have a 200 FSB in the bios because of DDR it doubles
    a true high speed FSB and in sync with the memory frequency is much better than just a large multiplier
    if my knowledge is wrong I apologize. pls help i really need to know 

    what default FSB should be displayed in the bios cell menu if my processor is a pentium 4 with a 800mhz FSB?
    but I really have a pentium 4 it says in the box it has a 800mhz FSB and the BIOS displays pentium 4 but it does'nt have HT. its an Intel 506 2.66G 1mb L2 cache LGA 775 pentium 4 processor none HT. its cheap thats why i bought it and upgrade later on
    can i lower the multiplier and increase the fsb to let say...400 and adjust the cpu ratio? it has a DDR2 memory at 533mhz is that right?
    i really don't have any sort of useful knowledge about this quad pumping scenes.... i mean processors going on in Intel Labs. sounds like an orgy to me....yeah pump that booty miss Northwood!
    I really don't have an idea how this pentium 4 works it been 3 yrs. since i've assembled a computer. technology moves so fast
    if your saying that i got a celeron D then that means i've got a fake pentium or a remarked? someone told me about this fake thing about processors in taiwan but its hard to believe that! imagine a processor built by a chinese   better get my lawyer then!

  • Can't reach the print button on the bottom of the page

    When the page preview page appears, I can't reach the print button at the bottom of the page.

    To use AirPlay, you will need the following:
    iPhone  4s (or later), iPad 2 (or later), iPad mini, or iPod touch (5th generation)
    Apple TV (2nd or 3rd generation)
    AirPort Express
    Wi-Fi (802.11a/g/n) network

  • How do I change the "You can be reached by Facetime at" phone number on my iPad? It currently shows my iPhone number.

    While I can make outgoing Facetime calls, incoming calls are not received because they obviously go to my iPhone number. I assume I need to change the "You can be reached by Facetime at" setting but cannot see how to do it.
    I am using the iPad with retina screen and have just updated to iOS7.

    Her phone number is in my FaceTime settings as well.  I have logged out and logged back in with my Apple ID, but it still shows here number despite the fact I have verified my number is associated with my Apple ID.

  • Can someone please help me figure out why I keep getting the "can not reach server" when I try to download the ebook? This is happening with Adobe Digital Editions.

    When I try to download the ebook I bough, the Adobe Digital Reader shows the following message: "can not reach server".  Can someone please help me with this?
    TO be precise, it says "licensee server communication problem"
    Thank you

    The thread running through your explanation has to do with connectivity to your server. (iCloud out of the blue asking for password, unable to message your boyfriend, unable to access e-mail). You said that you boyfriend restart his device and then the two of you were able to then imessage. My best advice for you would be to go to settings to reset to reset network settings. Once this has been done you then will need to enter the name and password of your wifi. ONce this is done you then can attempt to check to see that all passwords are enter correctly.
    Good luck.

  • I would like to see my photos on iCloud. Which way can I reach?

    I would like to see my photos on iCloud. Which way can I reach?

    Welcome to the Apple Community.
    You can see your photos on any device using your ID and photo stream.
    If you want to see them in a web browser you need to create a shared photo stream album and make it public.

  • I changed my phone number and now I cannot send iMessages or make calls on FaceTime (only receive) on my macbook. Currently my iMessage settings say I can be reached at my apple id email. My FaceTime currently says I can be reached at my apple id email.

    I changed my phone number and now I cannot send iMessage or make calls on FaceTime (only receive) on my Macbooth Pro. Currently my iMessages settings say I can be reached at my apple id email. My FaceTime currently says I can be reached at my apple id email.

    Go into Recovery Mode per the instructions here.  Also, since you have IOS-7, read this.

  • I can't reach the firefox home page, I'm stuck on the tutorials, and I need to access my flash settings for firefox mobile. What do I do?

    Basically I need to reach my firefox settings, so that I can automatically enable flash for every website. But I can't reach the settings, and every route that involves firefox leads me back to a tutorial -_-. I really need help.

    Yeah, what phones model you used ?
    To enables flash in firefox for android
    # just go to Menu > More > Setting
    # Tap Plugins in the Content section. The Plugins context menu appears.
    # To enable Flash to play for all websites by default, tap Enabled.
    # To disable plugins for all websites, tap Disabled.
    I am sorry if i am wrong, please let us know your problem :D

  • Adobe camera raw window won't resize and can't reach buttons

    When I open an image from bridge into adobe camera raw 6.1 (Photoshop CS5) on my laptop, the camera raw window fills all of the screen (top to bottom) and the buttons at the bottom of the window are below the task bar. Thus I can't open the image in photoshop except by hitting the enter key. I can't reach the open, etc buttons. The window won't resize and there are no icon/buttons in the right upper corner to go to/from full screen. When I hit the icon in the top right hand menu bar in ACR (to go to full screen size) the window then fills the whole width of the screen in addition to the height, but no matter what I do I can't get the height of the window to shrink, so that I can access the icons at the bottom of the screen. What am I missing? Thanks

    Don't worry about turning aero off just yet.
    There are two key first questions:
    What is your screen resolution (width in pixels x height in pixels)?  Right-click on desktop, choose Screen Resolution.
    What setting have you chosen for the display size (Smaller, Medium, Larger) in the Display dialog?  Right-click on desktop, choose Personalize, then Display.
    -Noel

  • HT4623 i have ios 4 version and when i try to update my iphone to the latest version it with itunes it can't reach the update server. what should i do?

    i have ios 4.3.3 version and when i try to update my iphone to the latest version it with itunes it can't reach the update server. what should i do?
    p.s.: i don't have any cinnection problem.....

    It could be the fact that your hosts file is directing itself to gs.apple.com Cydia not gs.apple.com Apple,
    Hope it helps
              http://support.apple.com/kb/TS3694
    Unable to contact the iOS software update server gs.apple.com
    Error 1004, 1013, 1638, 3014, 3194: These errors may be the result of the connection to gs.apple.com being redirected or blocked. Follow these steps to resolve these errors:
    Install the latest version of iTunes.
    Check security software. Ensure that communication to gs.apple.com is allowed. Follow this article for assistance with security software. iTunes for Windows: Troubleshooting security software issues.
    Check the hosts file. The restore will fail if there is an active entry to redirect gs.apple.com. Follow iTunes: Advanced iTunes Store troubleshooting to edit the hosts file or revert to a default hosts file. See section "Blocked by configuration: (Mac OS X/Windows) > Rebuild network information".
    Try to restore from another known-good computer and network.
    If the errors persist on another computer, the device may need service.

  • I can not reach to my accounts on computer since it says that 'connection server to .... is timed out'.

    I can not reach to my accounts on computer since it says that 'connection server to .... is timed out'. However, I can get my emails through my iphone. How can I make my accounts work on computer? This problem occurs occasionally but create a big problem for my works...

    If the iPads are Counterfeit then Apple will have nothing to do with them except maybe try to find the Counterfeiters and charge them.
    It's the usual story...  If something is too good or cheap to be true it probably is.

  • If you have many tabs open (in my case 30 tabs), you cannot click every single tab with your mouse, you can only reach them by opening the tab list at the right

    If you have many tabs open (in my case 30 tabs), you cannot click every single tab with your mouse, you can only reach them by opening the tab list at the right.

    You can create a folder with the home pages by using "Bookmark All Tabs" to open a specific page.
    You can place that folder on the bookmarks toolbar or use the Bookmarks menu button that you can find in the toolbar palette to get access to that folder easily.
    * Open the Customize window via "View > Toolbars > Customize" or via "Firefox > Options > Toolbar Layout"
    * "Bookmark All Tabs" can be accessed via the right-click context menu of a tab on the tab bar.
    * "Bookmark This Page" can be accessed via the right-click context menu of that browser page.

  • After downloading Yosemite, my Ps CS4 doesn't work. It says install legacy Java SE 6, but when i go ok, or, more info can not reach any point to have it!!!

    After downloading Yosemite, my Ps CS4 doesn't work. It says install legacy Java SE 6, but when i go ok, or, more info can not reach any point to have it!!! What will I do?

    I have similar issues and was referred to a knowledge base article support.apple.com/kb/DL1572  This seems to corrected the issue.

  • How can i reach at my pc documents from notability in my ipad through icloud

    how can i reach at my pc documents from notability in my ipad through icloud

    Sign in to iCloud.com

Maybe you are looking for