Can't read disk label: Booting Blade from CDROM

Folks !
I am trying to boot Sun Blade 100 from its internal IDE CD-ROM drive
using the Solaris 8 boot/installation CD (01/01). When I give the command
"boot cdrom" from ok fromt in OpenBoot, disk seems to spin for a moment
(green light comes on) but it eventually fails complaining:
can't read disk label
can'open disk label package
failed to open boot device.
I have tried following (all to no avail)
"boot /pci@1f,0/ide@d/cdrom@1,0:f" since devalias shows that cdrom is aliased to above. I also tried cdrom@0,0:f, but same result.
tried boot/installation CD from Solaris 9
did set-defaults reset-all
checked probe-ide and show disks output to make sure CDROM is recognized - it is primary slave.
swapped another IDE CD-ROM drived pulled from a PC. It was recognized but still not bootable.
Makes me wonder if PROM/NVRAM is corrupted. Hard disk
drive is trashed as such (another Blade 100 problem, since it was crashing
often, I had to force powerdown using the switch eventually leading
to corruption of basic files like /usr/lib/libnsl.so.1, so I can't force fsck)
I have to boot from CD to recover the machine and hopefully
repair the disk drive or swap it out and upgrade to Solaris 9.
any help would be appreciated.
thanks very much.
-Sanjay Kumar

as per the message it appears either you have a bad CD drive or CD media . If you have another machine try to boot this CD and verify it is working there. If the CD is ok you will have to swap the cd drive for testing
Hemant
http://www.adminschoice.com
Folks !
I am trying to boot Sun Blade 100 from its internal
IDE CD-ROM drive
using the Solaris 8 boot/installation CD (01/01). When
I give the command
"boot cdrom" from ok fromt in OpenBoot, disk seems to
spin for a moment
(green light comes on) but it eventually fails
complaining:
can't read disk label
can'open disk label package
failed to open boot device.
I have tried following (all to no avail)
"boot /pci@1f,0/ide@d/cdrom@1,0:f" since devalias
shows that cdrom is aliased to above. I also tried
cdrom@0,0:f, but same result.
tried boot/installation CD from Solaris 9
did set-defaults reset-all
checked probe-ide and show disks output to make sure
CDROM is recognized - it is primary slave.
swapped another IDE CD-ROM drived pulled from a PC. It
was recognized but still not bootable.
Makes me wonder if PROM/NVRAM is corrupted. Hard disk
drive is trashed as such (another Blade 100 problem,
since it was crashing
often, I had to force powerdown using the switch
eventually leading
to corruption of basic files like
/usr/lib/libnsl.so.1, so I can't force fsck)
I have to boot from CD to recover the machine and
hopefully
repair the disk drive or swap it out and upgrade to
Solaris 9.
any help would be appreciated.
thanks very much.
-Sanjay Kumar

Similar Messages

Can't read disk label

Dear Sun experts,
I am trying to install Solaris 9 on a Sun Ultra 10 Sparc workstation. This system formerly had Solaris 8 on it, but we decided to do a reinstallation to configure things the way we wanted them.Before doing that we encountered a few problems
1.The system failed to recognize the Dell Ultra Sharp Monitor, when the signal cable was plugged into the port behind the computer. To solve this we researched and were told to remove the Video card attached to the mother board, and this we did.The system now recognized the dell monitor and booted in Solaris 8.
2.We ran sys-unconfig to reconfigure the system to change the hostname on a reboot.We powered off the computer.Afterward we would go through the sys-unconfig program in an indefinite loop.So I powered off the computer each time i got stuck.
3.Lastly I tried to do a STOP A to try to go to the 'ok' prompt in order to do a clean installation of Solaris 8 Installation CD, by running
ok boot cdrom [ENTER]
Here's what I am getting:
Boot device: /pci@1f, 0/pci@1,1/ide@3/cdrom@2,0:f File and args:
Can't read disk label.
Can't open disk label package
Can't open boot device
ok
[end]
I want to do a clean installation of the Solaris 9 CD on the sparc ultra 10 computer.Please can anyone help me out? I looked at the solaris 9 installation guide, and it asked that I follow this procedure. Please respond if you can help.
Also of note is that I got this system from a user who had installed Solaris 8 sparc on it earlier.
Thanks a million!
Omon

Hi!
After a day fighting with same problem and found no good solution on the internet , I was able to do a workaround in order to be able to boot my sun bade 1500 that was giving the "can't open disk label" message.
I found no source of the problem but someone with more knowledge could guess. (maybe a default bad alias definition of cdrom ��?)
Well, first of all I plugued a normal IDE CDrom as primary slave, leaving IDE HD as primary master. And inserted solaris 8 installation CD (as it was my only solaris bootable CD, but I guess that I oculd boot any other CD).
After that, I went to the openboot prompt (ok>) and did next:
ok devalias cdrom - this will show you current path to internal CD. Use this to determine what new alias should look like.
ok setenv auto-boot? false
ok reset-all
ok probe-scsi-all - find the path to the new cdrom - write it down & write target # as well
ok show-disks - find the exact path you just wrote down and type that letter
ok nvalias cdrom2 [Ctrl] + [y] which will paste that path. Finish with @sd1,0:f AS IT's PRIMARY SLAVE
ok reset-all
ok boot cdrom2
I found this part in http://www.experts-exchange.com/Operating_Systems/Solaris/Q_ 20757891.html
except teh @sd1,0:f, I found that with my good luck!
After that I was able to boot with CD. the installation failed, but at least I was able to mount / filesystem and modify my /etc/passwd ... my target!
HTH
Cheers!

Can' t read disk label, install issues

can' t read disk label, install issues
i am trying to install solaris 8 on a sparc5 (256mb, 4.2gb,110mhz). i initially installed using the installation disk and it seemed successful as i was able to load the rest of the cds. something went wrong though b/c the system is stuck in a rebooting loop after it finished the last cd. so i went searching and found that i could only have a root partition of no bigger than 1gb. since i used the installation disk, i was not given an option to specify slice sizes. so now, i am trying to redo the install starting from the first disk (1 of 2) and skipping the installation disk. when i do a "boot cdrom" with the 1 of 2 disk, i get the cant read disk label or something about short entry and it will not boot. i am using actual Solaris 8 cds and not downloads. what can i do to get it to boot up from the first disk, or fix the partitioning on the disk?

I am using the offical Solaris 8 Installation 2/02 for SPARC Platform Edition for Sun Computer Systems February 2002, Revision A
Output from the probe-ide command follows:
device 0 (Primary Master)
ATA Model: ST3160023A
device 1 (Primary Slave)
Removable ATAPI Model: LTN4865
device 2 (Secondary Master)
ATA Model: ST340016A
device 3 (Secondary Slave)
not present
device 0 is the new hard disk that I just installed
device 1 is the CDR drive
device 2 is the original hard disk. I can boot this but now get some magic disk errors or something like that
device 3 is not present
I have all devices set to cable select according to the manual.
Thanks for your help...
Tom

Boot image does not exist and cannot read disk label errors.

Hi - I'm having a problem with installing Solaris 9 4/04 on a Netra T1. The Netra already has Solaris 7. I need to get this set up as a jumpstart server but it can't find the boot image. I'm using a brand new bonafide installation disk - not a copy. The system won't let me install/upgrade to Solaris 9 either. I get an error stating that disk label can't be read. I've tried swapping out the CDROM but I still get the same errors. Does anyone know what or why this may be happening? (Oh - and another strange thing - like I said the CDs are the original but there doesn't appear to be a cdrom/cdrom0/s0 directory. The directory I see is cdrom/cdrom0/sol_9_404_sparc/Solaris_9/Tools)
ERROR: Install boot image /cdrom/sol_9_404_sparc/Solaris_9/Tools/Boot does not exist
Check that boot image exists, or use [-t] to
specify a valid boot image elsewhere.
and
Excuting last command: boot cdrom [- nowin]
Boot device: /pci@1f,0/pc1@1/ide/cdrom@2:f file and args: [- nowin]
Can't read disk label.
Can't open disk label package
Evaulating: boot cdrom [- nowin]@1/ide@e/cdrom@2:f File and args: [- nowin]
Can't open boot device
I appreciate any help at all - is there anyone out there who can tell me what I may be doing wrong?
Thanks

Hi check that you are booting of the right cd. Make sure it is soalris 9 software 1/2 if that fails then it may well be that your cd is buggered. most likely it is buggered it it cant find the boot image.

Can't read the disk label & Can't open disk label package

Hi
I can't read the disk label & can't open disk label packages...I used the format command but there are do not showing any label...Please HELP
Thanks
Mohammed Tanvir

Hello worl !:
I'm installing a Tape in my Sparc 5. The system works whit Solaris 2.4.
When I boot the system without the tape it starts normally. But, the problem is when I put the tape... and I have this message:
Can't read disk label
Can't open disk label package
Can't open boot device
In the prompt I did:
ok probe-scsi-all
Target 3 Disk SEAGATE
Target 4 Removable only Tape ARCHIVE // my TAPE
Target 6 Removable Read only device TOSHIBA XM- // my CDROM
ok boot -r
Can't read disk label
Can't open disk label package
Can't open boot device
I check with the commnad 'devalias' and all the paths are ok. I probe when 2 different tapes and I format the disk using the command format booting the system without the tape . But I've the same error when the tape is connected.
Someone can help me?
[email protected]
HPP.

Can't open disk label package

Hi,
i just tried to make a boot DVD for Solaris 9 9/05 from a image file (.iso)
the iso file size is about 4.383GB.
tried with the nero express with the option copy image to disk.
succefully burnt the details, even the expected .flar file exists in the burnt DVD.
But when i tried in the SUN machine E2900, i got the following error,
Rebooting with command: boot cdrom
ERROR: disk-label do_read: Short disk read
Can't open disk label package
ERROR: Can't open boot-device
- I guess the fashion in which we are writing an image file to the DVD matters. if somebody faced the same situation, please do suggest me how to proceed ?
thank you very much
//regrds
siva

Hello worl !:
I'm installing a Tape in my Sparc 5. The system works whit Solaris 2.4.
When I boot the system without the tape it starts normally. But, the problem is when I put the tape... and I have this message:
Can't read disk label
Can't open disk label package
Can't open boot device
In the prompt I did:
ok probe-scsi-all
Target 3 Disk SEAGATE
Target 4 Removable only Tape ARCHIVE // my TAPE
Target 6 Removable Read only device TOSHIBA XM- // my CDROM
ok boot -r
Can't read disk label
Can't open disk label package
Can't open boot device
I check with the commnad 'devalias' and all the paths are ok. I probe when 2 different tapes and I format the disk using the command format booting the system without the tape . But I've the same error when the tape is connected.
Someone can help me?
[email protected]
HPP.

Can't open disk label

Hello world !!:
I'm installing a Tape in my Sparc 5. The system works whit Solaris 2.4.
When I boot the system without the tape it starts normally. But, the problem is when I put the tape... and I have this message:
Can't read disk label
Can't open disk label package
Can't open boot device
In the prompt I did:
ok probe-scsi-all
Target 3 Disk SEAGATE
Target 4 Removable only Tape ARCHIVE // my TAPE
Target 6 Removable Read only device TOSHIBA XM- // my CDROM
ok boot -r
Can't read disk label
Can't open disk label package
Can't open boot device
I check with the commnad 'devalias' and all the paths are ok. I probe when 2 different tapes and I format the disk using the command format booting the system without the tape . But I've the same error when the tape is connected.
Someone can help me? Thanks a million
[email protected]
HPP

Hello worl !:
I'm installing a Tape in my Sparc 5. The system works whit Solaris 2.4.
When I boot the system without the tape it starts normally. But, the problem is when I put the tape... and I have this message:
Can't read disk label
Can't open disk label package
Can't open boot device
In the prompt I did:
ok probe-scsi-all
Target 3 Disk SEAGATE
Target 4 Removable only Tape ARCHIVE // my TAPE
Target 6 Removable Read only device TOSHIBA XM- // my CDROM
ok boot -r
Can't read disk label
Can't open disk label package
Can't open boot device
I check with the commnad 'devalias' and all the paths are ok. I probe when 2 different tapes and I format the disk using the command format booting the system without the tape . But I've the same error when the tape is connected.
Someone can help me?
[email protected]
HPP.

Help. I have Creative Suites 5.5 on my MacBook Pro. Unfortunately, I had a major malfunction and must reformat the disk. How do I transfer Creative Suites to my desktop if I can't locate the programs booting up from my startup edrive?

Help. I have Creative Suites 5.5 on my MacBook Pro. Unfortunately, I had a major malfunction and must reformat the disk. How do I transfer Creative Suites to my desktop if I can't locate the programs booting up from my startup edrive?

http://helpx.adobe.com/creative-suite/kb/cs5-5-product-downloads.html
Mylenium

"Bad checksum in disk label" & "Can't open disk label package"

Hello,
I'm brand new to Sun/Solaris.
I have a Sun Blade 150, with SunOS 5.8.
I wanted to make a backup to prevent future data loss, so I put the disk in a normal PC with Windows XP to try to make a backup with Norton Ghost, the disk was detected, but not the file volume, so I place the disk on a desktop PC, and used Norton Ghost for DOS, the disk was recognized but once again not the file volume, so I wasn't able to make a disk backup, and I quit.
Put back the disk on the Sun Blade 150 PC, and then I was unable to startup the PC, showing the message "Bad checksum in disk label" and "Can't open disk label package".
What's wrong?
How can I solve this?
I need the data that's inside the hard-disk, so I cannot make a clean install, and i also don't have any install CD.
Thanks for any help,
JS

Thanks for the fast response,
i did't allow WindowsXP to write anythink to the disk, but somethink is written,and I don't know what. So now, the Spark-System dosn't boot from the HDD and the data on the disk is very important for me! When I format the disk all data are lost, right?
Is there a way to "rewrite" the Disk-Label-Checksum? I have an original Boot-CD-ROM, another HDD to install Solaris and so one, but I need the data of the corrupted HDD. And I also have not really a glue to use Solaris or any other UNIX, I'm a Windows-User.........

How can we read the screen field values from the report selection screen wi

Hi expart,
How can we read the screen field values from the report selection screen with out having an ENTER button pressed .
Regards
Razz

use this code...
AT SELECTION-SCREEN ON VALUE-REQUEST FOR p_posnr.
**Read the Values of the SCREEN FIELDs
CALL FUNCTION 'DYNP_VALUES_READ'

I can't read my eBooks I purchase from iTunes on my desktop or laptop. Do I need to go Amazon? Kindle?

Is there a future upgrade or availability to read eBooks purchased from iTunes on my desktop or laptop Mac?
If not, I am just going to get the free Kindle application and buy all of my ebooks from Amazon as I can read them on any Mac.
I purchased a book from Apple yesterday so that I could read it as a break during my work day at my office and it would not open. I checked and sure enough, you can't read books on your desktop Mac using Apple software. I tried the Adobe Digital software and a couple of others but the protection on the ebook prevented anything but my iPad or, if I had one, iPhone from reading it.
Considering that I spent many thousands on getting the best Macs for work and only hundreds on the pad, it is just a little irritating that I can't read a book on the pro machinery but can on the consumer toy.

We don't know what Apple plans on doing to change this (and it may not be just Apple but more likely the publishers, since Apple would, of course, do whatever it could to maximize sales/profits). Right now you can only read Apple books on mobile devices. Sure, buy them from Amazon if you want to read them on the computer. We don't work for Apple so we're pretty impartial on this kind of advice.
You might also see what your library can offer. My wife can browse the county library from her iPhone, borrow e-versions, and read books on it too. Free!

Out of the blue! clicking HD, "can't read disk"

I've got a 4th gen. click wheel.
I didn't drop it, I didn't sit on it, I didn't give it a bath...
I just plugged it in this morning, and out of the freakin blue:
the first sign was that it wasn't showing up in itunes.
The second was that when I tried to quit itunes, the whole computer froze.
The third was when I finally unplugged the iPod, the harddrive was clicking HARD.
It had reset by itself and was on the Apple logo, which soon became that dreaded crosseyed ipod with "apple.com/support" on it. Good. God. So I reset it again and again and at one point it seemed to be back to normal.
But then I had to leave, and when I came back, the problem had started again. It was resetting itself over and over, I reset it and brought it into disk mode, and now it won't come out or disk mode!
And now, when I plug it into the computer, I get a friendly little "cannot read disk" message.
... Any suggestions?

I'm having a similar problem with one of our media drives.
my backup just died. really, really can't afford do lose this data...and have 500GB.
any suggestions? other than reformatting? here's the error that i've gotten:
Verifying volume Media Server
Checking HFS Plus volume.
Invalid B-tree node size
The volume Media Server needs to be repaired.
Error: The underlying task reported failure on exit
1 HFS volume checked
Volume needs repair
tried disk repair, and tried tech tool pro 4. no success.
I just need to copy the data off...and then i can throw the darn drive in the trash. Help ASAP! please!

Can I read a book I downloaded from the App Store to my phone on my non-Apple laptop?

So, I downloaded a book from the App Store onto my iPhone. This is great as I can read it on the bus, but while at home I would prefer to read it on a bigger screen. I don't have an iPad or Apple laptop.
Am I able to read it on my Dell laptop? If so, how do I do this?
Thanks!

No, but Barnes & Noble eBooks can be read using the Nook iPhone app, and they have Mac OS X app, a Windows app, plus you can read the eBook via any web browser.
I'm not sure about Amazon Kindle eBooks. I know you can read them on an iPhone via the Kindle app, just not sure if Amazon has a Mac or Windows app. I'm sure you could check at the Amazon.com web site.

Can't read .doc or .xls files from Safari!

Not sure if this is a bug or an intended deletion, but I can;t open .xls or .doc attachments from my browser-based email. My work email uses Outlook Web Access and the company will not allow mobile devices except the Blackberry to access the mail server. How can I read attachments to web-based emails through Safari???

I figured out that if the email is formatted as plain text, an attachment coming into iPhone Mail from Outlook can be read, whereas if the email message is in HTML format (my PC Outlook default), it cannot.
This could well be a good workaround for you - send your email message in plain text format whenver you include an attachment.
Has anyone figured out a way to solve this - where you can view an attachment to an HTML formatted email?

How can i read all my past messages from imessage from my iphone into my laptop?

i need to see my messages how can i read it on my lap top

Install one of the many apps for your computer that can view iphone messages eithr from the iphone backup on your computer or directy from the phone.
Google "iPhone mesage viewer"

Can't read disk label: Booting Blade from CDROM

Similar Messages

Maybe you are looking for