Can't rename can chassis in MAX (9188XT)

Hi community,
I am unable to rename my NI 9188XT chassis under MAX. I can change the hostname, but not the actual device alias. Its not a name conflict as I can not rename it to anything, whatever I type it changes back to cDAQ9188XT. I have restarted the unit several times. A screenshot is attached.
Any reason behind this?
thanks!
Attachments:
9188_rename.png ‏58 KB

I have the same problem.
I don't like to leave the default name in case I change chassis to run the same program. I would have to reconfigure max.
JCollado

Similar Messages

Crystal 2008: Text, Can Grow=true, Max Lines=0, truncated after 2 lines

I have a fairly simple, grouped report with a handful of fields in each Detail section, one of which is a note/text field. I put the text field on its own line and set Can Grow = true, max lines = 0 so that it will display what it needs to display.
This happens to be a crystalreports.com report using data coming from Salesforce, and I can see in the source report that I have about 7 lines of text for one of my groups, but crystal is truncating it after two lines, and in the middle of a word.
The word ('for') doesn't have any obvious special characters in it, so I'm guessing that there's some sort of character limit that I'm bumping up against.
I have another record that is returning more than two lines, though; are there particular characters that could cause this? I can scrub the data and/or put Salesforce Validation Rules in place to try and prevent them from getting in.
Any suggestions would be appreciated.
Duncan

Please re-post if this is still an issue or purchase a case and have a dedicated support engineer work with you directly:
http://store.businessobjects.com/store/bobjamer/DisplayProductByTypePage&parentCategoryID=&categoryID=11522300?resid=-Z5tUwoHAiwAAA8@NLgAAAAS&rests=1254701640551

Help I can only have max. 3 osx apps. open at the same time ?

Help I can only have max. 3 apps. open at the same time ?
If I have 3 apps. open, and try to open a 4th. this message comes up :
The application "Mail" cannot be launched. -10810
Of cause if I'm trying to open up something else than mail, lets say iPhoto, it will say "iPhoto".
This is very weird to me, and I'm normally pretty good at solving issues myself, but I'm stuck with this one.
Please help out

I've had this quite a lot too. Do you find that under these conditions you can't load a disk image either?
At first I put this down to Rosetta taking up a lot of resources. I was running OmniWeb with a lot of pages open in the workspaces so I've switched back to Safari until OmniWeb is UB. This morning I read that having Windows file sharing switched on helps to cause this problem. I switched this off, rebooted and ran disk utility to repair disk permissions and I've been running OK since then. I've currently got 13 apps open plus Finder and Widgets. They include 2 bigguns, Eclipse/MyEclipse and Visual Paradigm for UML. It'll probably stop working now I've written that.
I run a MBP 17 with 2GB memory. My guess is that Windows file sharing does cause problems. I just hope Apple has resolved this in 10.4.7... whenever that is.
Gareth

How We can restrict the max no of Selections in JList

Hi,
How We can restrict the max. no of selections (at random selections) in JList (ex. max No of of selections is 3 in a JList of having 50 items.)
Thanks for your advise in advance.

Hello Satyaki De.
Thank you very much for your suggestion but my Private information is totally apart from this question & I already I have changed each and every information from the question.
Thanks
Kamlesh Gujarathi
[email protected]

Can I install Max OS X Lion from Tiger 10.4.11? If so, how can I do it?

The questions is simple,
I want to buy Mac OS X Lion and install it on my macbook. I am using OS X Tiger 10.4.11. The problems is that it seems that in order to instal OS X Lion it is necessary to have the last version of OS X 10.5 (Snow Leopard).
So the question is, Can I install Max OS X Lion from Tiger 10.4.11? If so, how can I do it?
Thanks in advance,
Best regards,
Jesus P.

Hi,
This Question has been asked and answered many times...
See this Link for pertinent information:
https://discussions.apple.com/message/15357762#15357762
Cheers,
(Also... Just to Clarify... Snow Leopard is OS X 10 6)

How can I get max, min & average (hours with minutes) of fast 30 days data

Table name:
run_log
TYPE VARCHAR2(10),
SUBTYPE VARCHAR2(10),
PROGRAM VARCHAR2(100),
STATUS VARCHAR2(20),
START_TIME      DATE,
END_TIME      DATE
How can I get max, min & average (hours with minutes) of fast 30 days data ?

Hi,
you have to use analytical functions:
SELECT start_day,
       round(AVG(daily_avg)
             over(ORDER BY start_day ASC RANGE BETWEEN INTERVAL '30' DAY preceding AND INTERVAL '0' DAY following)) AS moving_avg,
       round(MAX(daily_max)
             over(ORDER BY start_day ASC RANGE BETWEEN INTERVAL '30' DAY preceding AND INTERVAL '0' DAY following)) AS moving_max,
       round(MIN(daily_min)
             over(ORDER BY start_day ASC RANGE BETWEEN INTERVAL '30' DAY preceding AND INTERVAL '0' DAY following)) AS moving_min
FROM (SELECT trunc(t.start_time) start_day,
               AVG((t.end_time - t.start_time) * 24 * 60 * 60) AS daily_avg,
               MAX((t.end_time - t.start_time) * 24 * 60 * 60) AS daily_max,
               MIN((t.end_time - t.start_time) * 24 * 60 * 60) AS daily_min
          FROM run_log
         GROUP BY trunc(t.start_time)) t
ORDER BY 1 DESCAnalytical functions are described in the Oracle doc "Data Warehousing Guide".
Regards,
Carsten.

What can be the max difference in cable lengths that we can have between the ISLs in a port-channel between MDS switches?

Hello All
What can be the max difference in cable lengths that we can have between the ISLs in a port-channel between MDS switches? Do we have any documentation?
Thanks
Chetan

competitive solution instead recommends a distance variance of 30 meters or less among ISLs within a trunk. If the distance variance is greater than 30 meters, undesired and degraded performance will occur. For example, if a trunk has a distance of 100 kilometers, the competitive trunking solution allows a cable length variance of only 0.03 percent!
ref;
http://www.cisco.com/c/en/us/products/collateral/storage-networking/mds-9500-series-multilayer-directors/white_paper_c11-534878.html
hth
regards
inayath
**********PLZ dont forget to rate if this info is helpfull.

Pb of transmition of a message on CAN bus with MAX using a CANdb file (.dbc)

Hello,
I tried to transmit a message on the CAN bus with MAX, I used a database.
I have tried to transmitsome datas with the "NI CAN channel test pannel" (right click on a channel of a message), I put my value i click on "start", then "send" and when I look at the "Bus Monitor" (right click on CAN0) I see messaged that are received but I don't see my message transmit...
Why my message are not transmitted?
Bye.

Duplicat post: http://forums.ni.com/ni/board/message?board.id=170&message.id=247678&jump=true
LabVIEW Champion . Do more with less code and in less time .

Can we simulate CAN card in MAX

Hi
We can simulate DAQ cards in MAX.But can we simulate CAN card in MAX ?????
I am using PCI CAN series-2 card.
Please reply

No posting of code is needed, open the Help >> Example Finder.
Search for the example CAN Receive.vi, and Transmit Receive same Port.vi. Before running the CAN Receive.vi set the interface to CAN257, then run it. Then in the Transmit Receive same Port.vi set the interface to CAN256 and then run it. Now when you click Write it will send a frame out on CAN256. CAN256 and CAN257 are virtual loop back ports. What is sent on one is received on the other. So you should see the frame you wrote appear in the CAN Receive.vi which is monitoring 257.
Using this technique you can write code that monitors one of these ports, then reacts sending simulated data when requested, or set it up to just periodically send the data you want.
Unofficial Forum Rules and Guidelines - Hooovahh - LabVIEW Overlord
If 10 out of 10 experts in any field say something is bad, you should probably take their opinion seriously.

Can't reach max (also with fancontrol) and min fan speed manually

I'm using fancontrol to control my fan's speed. One thing I noticed is that maximum fan speed is never reached even when temperatures exceed max limit.
If I set max temperature in /etc/fancontrol to 55 and restart fancontrol, 55+°C will cause fan to speed only at ~5800 RPM. If I set min temperature to 60, fans will completely stop. 'pwm_enable' is set to 1 when fancontrol is running.
Now if I stop fancontrol, fan will speed up to ~6460 RPM while 'pwm' is at 255 and 'pwm_enable' changed to 0. I can't change 'pwm' value at this point. If 'pwm' gets set to 0, fan will completely stop.
At this point fancontrol is still not running. If I set 'pwm_enable' to 1 and leave 'pwm' at 255, fan will slow down to ~5800 RPM. If I set 'pwm' to 0, fan will not slow down completely, but will instead slow down to ~2080 RPM.
What's interesting is that although fancontrol can't reach max fan speed, it can stop fan completely, while I can do neither manually.
Any idea how to enable at least max fan speed for fancontrol?

I'm using fancontrol to control my fan's speed. One thing I noticed is that maximum fan speed is never reached even when temperatures exceed max limit.
If I set max temperature in /etc/fancontrol to 55 and restart fancontrol, 55+°C will cause fan to speed only at ~5800 RPM. If I set min temperature to 60, fans will completely stop. 'pwm_enable' is set to 1 when fancontrol is running.
Now if I stop fancontrol, fan will speed up to ~6460 RPM while 'pwm' is at 255 and 'pwm_enable' changed to 0. I can't change 'pwm' value at this point. If 'pwm' gets set to 0, fan will completely stop.
At this point fancontrol is still not running. If I set 'pwm_enable' to 1 and leave 'pwm' at 255, fan will slow down to ~5800 RPM. If I set 'pwm' to 0, fan will not slow down completely, but will instead slow down to ~2080 RPM.
What's interesting is that although fancontrol can't reach max fan speed, it can stop fan completely, while I can do neither manually.
Any idea how to enable at least max fan speed for fancontrol?

Configuring multiple chassis in MAX

I am looking for some help/documentation on how to configure two chassis in MAX?

Hi Abhay,
What chassis do you have and what version of MAX? There are a few documents you may find helpful:
Multi Combo Chassis Setup
Configuring a PXI-1010 or PXI-1011 in MAX
You can also look in the MAX Help under Installed Products»PXI»MAX Help for PXI»PXI System Configuration or
Installed Products»NI-DAQ»MAX Help for NI-DAQmx»Getting Started»SCXI Devices»SCXI Chassis
Happy Thanksgiving!
aNItaB
Applications Engineer
National Instruments
Digital Multimeters

Can't add simulated SCXI chassis in MAX

Hi all
I wanted to test some hardware by simulating it on my workstation. I'm using Labview 8.2 and MAX 4.1.0
When I try and simulate the SCXI 1000 chassis, the first dialog box appears with the chassis communicator dropdown control greyed out. The chassis address box is available. When I try and save it keeps asking to select a communicating DAQ device but it doesn't seem to have a spot for that. I don't know if I'm missing something or if I need an update to MAX. Anyone had this issue?
Thanks in advance
Chuck

Hi Chuck,
You're right... the SCXI 1600 cannot be simulated according to the following KnowledgeBase article:
What are NI-DAQmx Simulated Devices and How Do I Use Them?
Are you having trouble simulating any of the other modules, or just the 1600?
- Greg J

T510 w/ NVS 3100m can't show max resolution for a dell 30Inch

T510 Docked
Windows 7 64bit
Dual-Link Cable attached to Dell 3007WFP monitor.
Max Resolution is 1280x800
Ironically, I have a second monitor attached on the DVI port 2 Single Link and this is 1600x1200
NVIDIA NVS 3100m
Why can't this display the max resolution for this monitor.
I have the latest drivers

sonniep5 wrote:
I had same issue, tech support advised me to return T510 since it didn't ship what I ordered. In my case the resolution should be 1920x1080.
you are talking about the FHD on the T510, this is slightly different to what the OP is asking.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

How can specify the max width of uix pages in a browser

If I have 7 tabs in my jheadstart application. This
works fine on a 1200X1000 resolution but on a
1024X720 resolution the users have a scrollbar
how can i specify the max resolution in jheadstart

Tnx Steven "God" Davelaar ;-)
Edwin:
When you are about to edit the tab-bars (any level),
make sure you disable the tabbar generation (service-
level). Each uix-page calls this tabbar with a parameter
for selected-tab (0 to n). If you edit the *tabbar.uit
and for example, merge 2 tabbars into 1 (with a level 2
globalheader for further navigation), don't just delete
the code in the uit-file, but simply set one of them to
rendered=false (instead of
data:rendered=groupname@infoTable:something). This will
not screw up the selected-tab settings on all pages where
the selected tabbar is on the right (higher number) of
your merged one.
And have fun with UIX (I know you will)

How can i write max and min data online during acquisition

Hello,
I am not keen with programming and your help will be greatly appreciated.
I make temperature acquisition from an IR camera and I record online 38 different spots at a frequency of 10 samples/min.
I also record two temperatures from thermocouples at the same sampling rate.
I would like to make the acquisition during 5 sec every 20 sec and extract the max and min temperature from the thermocouples and write these values in a text file like show below :
Temp_max 5 sec 22.1
Temp_min 5 sec 2.1
Temp_max 10 sec 42.1
Temp_min 10 sec 4.1
Temp_max 15 sec 82.1
Temp_min 15 sec 6.1
I also would like to make the same with two or three different spots of the IR camera. I think that if I have a good solution for the thermocouple, I can make it for the camera.
I use LabView 8.2 with NIDaqmx acquisition.
Thank you in advance

Hello Evrem,
Thank you for your advice. In fact, I have already attended to the training course you mentioned. I should think about going to the module Basic II. I do not have problem to connect/pilot various type of instruments but I am not very efficient with loop and arrays !
I am fine with the data acquisition and the timing and I can sort data during 5 sec with "Array max & min". Then, I can display all data. What I have problem to do is to extract the max & min from the array, keep these 2 values for being writtten in a file at the end of my loop and start again during the next 5-sec cycle. At present, I only have the last max & min results from the last acquisition !
Any example of how recording max & min online during 5-sec cycle acquisition will be welcome.
Best regards,
Labdummy

Can't rename can chassis in MAX (9188XT)

Similar Messages

Maybe you are looking for