Can't restore my iPod Touch 2G or update it. Help?

I plugged it in to upgrade to 3.1.2 and it got stuck in recovery mode so i waited until the download was complete and at 1sec remaining it keeps stopping and coming up with an error. Have downloaded twice now and it keeps coming up so i downloaded an older version of the software and it worked and installed but it wouldnt let me restore to update it. Any suggestions

YaHOO!!! I tried the recovery again today (just hoping they had fixed the bug in update) and it looks like it worked! It resored from my back up (thank goodness I had one) and is now in the process of syncing.

Similar Messages

  • I can't restore my ipod touch

    I can't restore my ipod touch, it says: error 21

    Use the following steps to place your device into recovery mode. If the device is already in recovery mode, you can proceed immediately to step 6.
    Disconnect the USB cable from the iPhone or iPod touch, but leave the other end of the cable connected to your computer's USB port.
    Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the the iPhone or iPod touch to turn off.If you cannot turn off the device using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the device turns off, release the Sleep/Wake and Home buttons.
    While pressing and holding the Home button, reconnect the USB cable to iPhone. When you reconnect the USB cable to iPhone, the device should power on.
    Note: If you see the screen pictured below, let the device charge for at least ten minutes to ensure the battery has some charge and then start with step 2 again.
    Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button:
    If necessary, open iTunes. You should see the following "recovery mode" alert:
    Use iTunes to restore the device.
    If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.

  • I can't restore my ipod touch 3g

    i can't restore my ipod touch because i can't download itunes

    What exactly happens when you try to download and install iTunes?
    You need a computer with iTunes and an internet connection to restore your iPod.
    iTunes: Restoring iOS software

  • HT1212 How can i restor my ipod touch? I forgott my password to...

    How can i restor my ipod touch? I forgott my password to...

    Connect the iOS device to your computer and restore via iTunes. Place the iOS device in Recovery Mode if necessary to allow the restore.
    If recovery mode does not work try DFU mode.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    For how to restore:
    iTunes: Restoring iOS software
    To restore from backup see:
    iOS: How to back up
    If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
    You can redownload iTunes purchases by:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store

  • How can i restore my ipod touch 4g (?) without passcode or itunes

    Hi and thank you for helping as this is urgent.
    I forgot my passcode for my iPod, and guessed it to many times so it got disabled.
    The problem is I don't have iTunes and can't get it on my laptop, but need to restore my device. Right now on the screen it has a photo of a USB cord, an arrow, and the iTunes symbol. So, how can I restore my iPod touch without my passcode or iTunes?
    Thank you SO much.

    Right now you can't without a computer. Once you get to a computer you can restore it using DFU mode.

  • Please how can I restore my ipod touch 2g from a firmware that I own already on my computer and without any time need to download via itunes

    please how can I restore my ipod touch 2g from a firmware that I own already on my computer and without any time need to download via itunes

    You should probably disable the autosync functionality first by going to Edit -> Preferences, clicking the Devices tab, and enabilng the prevent iPods,iPhones, and iPads from automatically syncing option.
    Next, authorize the new computer with your iTunes Account.  In iTunes, choose Store -> Authorize This Computer and enter in the correct credentials.
    If possible, either copy a backup file from your old computer to your new one or create a new backup of your iPod in iTunes before letting it sync.  To do this, right->click on your iPod Touch from under the Devices section in the left hand pane of iTunes and choose Backup. You might also want to take a look at this article to see what it all included in the backup.
    http://support.apple.com/kb/ht1766
    Now onto synced content such as music, videos, photos, etc.  For iTunes purchases you can copy them back into iTunes by choosing File -> Transfer Purchases.  For all other nonpurchased iTunes content, see this older post from another forum member Zevoneer covering different software availbable to assist you with this task.
    https://discussions.apple.com/thread/2452022?start=0&tstart=0
    Once the backup has been made and all other synced content such as music, videos, and photos are back in your iTunes library, restore your iPod from that backup you made earlier.  Here is more on backing up and restoring your iPod.
    http://support.apple.com/kb/ht1414
    B-rock

  • I can not restore my Ipod touch keep getting a 1611 code

    Need help ..can not restore my Ipod touch I keep getting a code 1611

    If you are using a Windows based computer, disable a/v software and turn off the Firewall.
    Disable antivirus software
    Turn Windows Firewall on or off

  • I can not restore the ipod touch 4th getting an error 2003

    I tryed to sync my ipod touch 4 Gen. and for some reason I got An ipod has been detected,but it could not be identified properly. please disconnect and reconnect the ipod then try again, I did that 3 times then I got I need to Restore it back factory settings.
    Now I am getting the ipod could not be restored. An unknown error occurred (2003) what should I be doing I did check for updates for the computer got some and then did a restart, still have this problem and I can't use my ipod touch at this point.

    Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on)
    If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you're using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that doesn't resolve the issue, try the USB issue-resolution steps listed for Error 1604 above. If the issue persists, it may be related to conflicting security software. If the errors persist on another computer and known-good USB cable, the device may need service.
    The "device may need service" means a hardware problem. In that case make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar

  • Can not restore my ipod touch 4 !!!!

    I was trying to u upgrade my ipod to ios 5 but when I finised upgrading , I was not able to restore my ipod back.I tried to look up youtube videos and looked of in internet and tried to work it out but nothing worked out. What should I do, can anyone help me with it???

    I suspect you have a 2G iPod. Those can only go to iOS 4.2.1.
    Identifying iPod models
    iPod touch (3rd generation)
    iPod touch (3rd generation) features a 3.5-inch (diagonal) widescreen multi-touch display and 32 GB or 64 GB flash drive. You can browse the web with Safari and watch YouTube videos with Wi-Fi. You can also search, preview, and buy songs from the iTunes Wi-Fi Music Store on iPod touch.
    The iPod touch (3rd generation) can be distinguished from iPod touch (2nd generation) by looking at the back of the device. In the text below the engraving, look for the model number. iPod touch (2nd generation) is model A1288, and iPod touch (3rd generation) is model A1318.

  • I can not restore my iPod Touch 3rd

    Hi, I am trying to restore my Ipod Touch 3rd, but when the restoration is about 99% it stops and no more finish, someone may help me?
    Message was edited by: xitis

    Welcome to the discussions,
    did you make sure your security software does not block access to the Apple servers during the restore process.
    http://support.apple.com/kb/TS3125

  • I can't sync my iPod touch 4 after updating to ios 5

    I can't sync my iPod touch after updating to ios 5.
    Why?
    The problem is it keeps backing up for long time and I did nothing. Help me!!

    Some more information, please.  What happens when you attempt to sync?  Any messages?  Etc., etc., etc.

  • How can I restore my iPod touch data to a new hard drive when the old one crashed

    My computer crashed and I want to put the contents of my iPod Touch back on the new hard drive. How do I do this without accidentally Syncing and copying over my data? The vast majorioty of the music on my iPod is my own from DCs I own.

    You should probably disable the autosync functionality first by going to Edit -> Preferences, clicking the Devices tab, and enabilng the prevent iPods,iPhones, and iPads from automatically syncing option.
    Next, authorize the new computer with your iTunes Account.  In iTunes, choose Store -> Authorize This Computer and enter in the correct credentials.
    If possible, either copy a backup file from your old computer to your new one or create a new backup of your iPod in iTunes before letting it sync.  To do this, right->click on your iPod Touch from under the Devices section in the left hand pane of iTunes and choose Backup. You might also want to take a look at this article to see what it all included in the backup.
    http://support.apple.com/kb/ht1766
    Now onto synced content such as music, videos, photos, etc.  For iTunes purchases you can copy them back into iTunes by choosing File -> Transfer Purchases.  For all other nonpurchased iTunes content, see this older post from another forum member Zevoneer covering different software availbable to assist you with this task.
    https://discussions.apple.com/thread/2452022?start=0&tstart=0
    Once the backup has been made and all other synced content such as music, videos, and photos are back in your iTunes library, restore your iPod from that backup you made earlier.  Here is more on backing up and restoring your iPod.
    http://support.apple.com/kb/ht1414
    B-rock

  • I forgot my Apple Id and Icloud Id of my Ipod touch. how can i restore my ipod touch with new ID

    I have an Ipod touch 5S
    I forgot my Apple ID and my Icloud ID
    I tried to connect it to Itunes and do a ''restore as new Ipod'' but could not find this option
    Can you help me restoring my Ipod as new

    You need to recover them because yo will run into:
    iCloud: Find My iPhone Activation Lock in iOS 7
    Is there a way to find my Apple ID Name if I can't remember it?
    Yes. Visit My Apple ID and click Find your Apple ID. See Finding your Apple ID if you'd like more information.
    How do I change or recover a forgotten Apple ID Password?
    If you've forgotten your Apple ID Password or want to change it, go to My Apple ID and follow the instructions. SeeChanging your Apple ID password if you'd like more information.
    Ans if necessary:
    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Forgot passcode or device disabled
    If recovery mode does not work try DFU mode.                        
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings        
    For how to restore:
    iTunes: Restoring iOS software
    To restore from backup see:
    iOS: Back up and restore your iOS device with iCloud or iTunes       
    If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
    You can redownload most iTunes purchases by:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store        
    If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes should say it found an iPod in recovery mode.
    If you previously synced to the computer then you may be able to recover use of the iPod without erasing the iPod by following the instructions here:
    Disabled Recovery-must use syncing computer.

  • TS1441 How can I restore an iPod touch if the home button is broken and I don't know the password?

    I just bought my iPod Touch (4th Generation 8GB) from my friend and the home button doesn't work. Then, my parents took it away for about 6 months and I just got it back and I forgot my password. Then, I tried to get in too many times and now it says "iPod Disabled Connect to iTunes". Then, when I connect it to iTunes, it says for my to put in my password so it can connect. I've been trying to get back in but haven't found a way to restore it. HELP!!!!!
    P.S. It's jailbroken, but the damage isn't due to Cydia. Also, I can't put it into DFU mode since the home button is broken.

    Actually, I can give it to someone who fixes jailbroken iPod touch home buttons, but I don't want to pay anything. Also, if you just have something to say to me that will kill me, don't say it at all dude.

  • HT1212 How can I restore my iPod touch 4G with white on the display when it has a passcode on it and I know it butI can't enter the passcode on it?

    My iPod touch has white on the display. I need to restore it, but I can't enter the passcode on it. Is there any other way to type the passcode and restore it when I know the passcode?

    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    If recovery mode does not work try DFU mode.                         
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings         
    For how to restore:
    iTunes: Restoring iOS software
    To restore from backup see:
    iOS: How to back up
    If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
    You can redownload iTunes purchases by:
      Downloading past purchases from the App Store, iBookstore, and iTunes Store

Maybe you are looking for

  • VS2010 Crystal Report Crashes System when using 'Set DataSource Location..'

    Runtime ASP.NET 3.5 VS 2010 Under Database Fields (rt click) try Set DataSource Location... causes VS2010 to crash. This is on an imported report from VS2008.  VS2008 has no problem with the report. Since this is a ASP.NET 3.5 program the internal pr

  • I Tunes won't load videos

    hi all, My itunes will load and play quick time files and .m4v files but when you try and load a .avi or any other file type nothing happens. You go add file to library, selec file ans hit ok.. then nothing . nit doesn't apear under video's and there

  • Opening external files directly?(without prompting)

    Hello, I'm making a DVD menu in flash. It will open several kinds of files. .mov .avi . ppt . pdf etc. But i want to open those files directly, without prompting. When i try to open non web files, a popup window appears, as shown in this screenshot:

  • Programs quitting because of kern invalid address

    I have 2 programs FileMakerPro 8.5 and Printer Utility for Canon Pixma printer (that I know of so far) that crash because of FileMakerPro.... Date/Time: 2007-08-25 16:43:22.519 -0400 OS Version: 10.4.10 (Build 8R218) Report Version: 4 Command: FileMa

  • Any way to stamp date on prints?

    I need to stamp date and possibly other data on to my prints. Can't seem to find any info in the manual.