Can't see all devices from one AccessPoint to another? What is best setup to extend wireless coverage?

We have just moved into a new apartment with concrete walls, hence WiFi signal is quite weak in the other end of the apartment. Not all devices can see each other depending on which AP i am associated to.
Basically I want to have any wired/wireless devices be able to see my NAS/Office based components and keep the LivingRoom tidier. Only device in LivingRoom will be ISP components and AppleTV.
Some additional notes on current setup
- LivingRoom has the ISP issued Router/AccessPoint
- the ISP Router/AP is currently setup as a) AccessPoint b) DHCP server and c) default gateway to get to the Internet
- LivingRoom AP SSID is 'LivingRoom'
- DHCP pool is on the 192.168.1.0/24 range
- Default GW is 192.168.1.254
- in the LivingRoom i am also using the Router/AP ethernet ports for AppleTV
- connected to the Router/AP is a long Ethernet cable to the other end of the apartment in the Office
- on other end of the long Ethernet cable is an Airport Extreme in the Office on the WAN port
- the AirportExtreme is setup in 'Bridge' mode
- Connected to the Office_AirportExtreme is a) a NAS device physically in the Office via Ethernet cable b) WebCam in BedRoom2 via WiFi
- Office_AirportExtreme SSID is 'Office'
- all devices confirmed are assigned an IP from the LivingRoom Router/AccessPoint and on the 192.168.1.0 pool
- at this time in only have WebCam and NAS however Plex and Desktop coming shortly as we are still unpacking
Issue
a) When my laptop is associated to SSID 'Office' i can see the NAS and WebCam; able to PING and hit via HTTP
b) When my laptop is associated to SSID 'LivingRoom' i CANNOT see the NAS/WebCam; I am unable to hit the two devices behind the Office_AirportExtreme via PING/HTTP and I am able to surf the Internet, however cannot see the NAS/WebCam
Question
a) is there some other config on the Office_AirportExtreme that must be done to disable any Firewall type capabilities that is limiting the ability for devices on other side of the Office_AirportExtreme from seeing the devices behing the Office_AirportExtreme?
b) is this ideal config?
c) is it typical to have different SSID? would like to get to just single SSID for the apt, however not sure if there will be conflict i'm not aware of.
Totally open to any suggestions on others that have done this before to avoid reinventing the wheel...
See pic below...
Thx -Ray

Note that after additional poking around and disabling Wi-Fi all together confirmed that when wired to either the ISP Router/AP or the Office_AE, i am able to see both NAS and WebCam behind the Office_AE.
The issue seems to be with the ISP Router/AP where by there is a difference in behavior when connected via Wi-Fi vs Wired. All is well with the AirportExtreme from what i can gather.
i'm just going to pickup a separate Wi-Fi access point to provide coverage for the LivingRoom area instead of trying to figure this out further.
FYI. I am in Singapore using SingTel Fiber service and the ISP Router/AP i am using is Aztech DSL7000GRV(S)

Similar Messages

HT204053 i have two apple id one for Store purchases and the other for iCloud, and i want to merge them into one, can i transfer all app from one to other ?

i have two apple id one for Store purchases and the other for iCloud, and i want to merge them into one, can i transfer all app from one to other ?

It is not possible to merge Apple IDs.

I bought a new laptop and used Windows Easy Transfer cable and moved all files from one computer to another. I installed iTunes and found my iTunes music Library. However, when I plug in my iPod it says it is already synced with another iTunes Library.

I bought a new laptop and used Windows Easy Transfer cable and moved all files from one computer to another. I installed iTunes and found my iTunes music Library. However, when I plug in my iPod it says it is already synced with another iTunes Library.
I don't see anything in Help that shows when you already have transfered all the files over. Why would it want to erase and sync when I already have all the music folder copied over? I didn't have an issue when I had another technician copy from one laptop to another. Home sharing is also on but not being recognized.

I suspect you only migrated the media folder instead of the complete working library. Either review the transfer process and copy over the entire iTunes folder from your old profile's music folder or see Recovering your iTunes library from your iPod or iOS device.
tt2

Can i transfer my backup from one laptop to another?

I have my backup of apps and music stored in one laptop's iTunes account, how can I transfer my backup from one laptop to another?

iTunes downloads are not stored in a backup (that contains documents, files, camera roll photos, app content/settings etc), neither are the contents of the device's Music and Videos apps - instead a restore would look to pick up your music, films, apps etc from your iTunes library.
Your backups are stored under :
Mac: ~/Library/Application Support/MobileSync/Backup/
The "~" represents your Home folder. If you don't see Library in your Home folder, hold Option and click the Go menu.
Windows Vista, Windows 7, and Windows 8: \Users\(username)\AppData\Roaming\Apple Computer\MobileSync\Backup\
To quickly access the AppData folder, click Start. In the search bar, type %appdata%, then press Return.
Windows XP: \Documents and Settings\(username)\Application Data\Apple Computer\MobileSync\Backup\
To quickly access the Application Data folder, click Start, then choose Run. In the search bar, type %appdata%, then click OK.
You will need to copy the entire backup directory and copy it into the relevant directory on your other laptop - it should then automatically be picked up by that computer's iTunes and show on the Devices tab in Edit > Preference (iTunes > Preferences on a Mac) on it.
To copy your iTunes library between computers : How to move your iTunes library to a new computer.
You can also use home sharing to copy content between computers : iTunes: Setting up Home Sharing on your computer.

How can I transfer apps purchased from one AppleId to another due to breach of account?

Due to a recent security breach not if my doing a user stole my apple id and needed to change appleid account. Now as a result i've lost all purchased apps from the itune store. I would like to transfer apps from one apple id to another without incurring additional costs. With sufficient information in direct contact with the store I should be able to transferable within the software or at very least with the itune store direct. Perhaps this is a way of charging additional costs for same programs?
Not a happy camper because of the theft in id but now to add insult to injury i'll have to repurchase the apps to properly sync with my devices.
Any help would be appreciated

You can't transfer iTunes content from one account to another. If someone had obtained access to your account credentials and you've had the account locked that should not affect the current authorizations on your computer, though it will prevent you from updating apps until you have resolved the issue. Rather than creating a new AppleID what you should do is regain control of your original Apple ID and have it reenabled with a new password, get, if possible, Apple to deauthorize all computers for your account (assuming you don't have 5 so can't do it yourself) then authorize your computers.
tt2

Can you move your notes from one iphone to another and how?

Can you move your notes from one iphone to another and how?

You can do this a couple ways. If you are using MobileMe, notes is one of the options for synchronization and that would be automatic. Another way is to backup your iphone to iTunes, this backs up essentially all the information on your phone (except for music) and if you restore the other iphone to the image of the original your notes will be transfered.

How can I copy cell formatting from one range to another?

How can I copy cell formatting from one range to another, including text fonts, colours, borders, etc., so that, for example, I can reuse a formatted reconciliation table again in different parts of a sheet?

Hi George,
Wayne found the Spinning Beachball of Death, and you will find it too.
Numbers is not good at handling large datasets. Might I suggest that you group your data into smaller sets (each month, perhaps?) and save each group in a separate Numbers document. Numbers will not link between documents, but you could have a summary Table within each document. Then comes the "clunky" bit of copying all those summary tables into a master document where you do the final processing of the data.
Regards,
Ian.

How can I pass the photos from one iphone to another?

how can I pass the photos from one iphone to another?

Use the Beaming feature. See the info at the ? In iPhoto for iOS.

How can I move a photo from one project to another

How can I move a photo from one project to another without creating a duplicate so I have the same photo in two projects.
I seems to me in the past when I moved the photo from project 1 to project 2, I would get a number showing the # of photos being moved and you could drag and drop in the 2nd folder and the photos would disappear from project 1 and show up in project 2. is there a setting I am missing. Now when I drag and drop the photo no red # shows up and the photo stays in project 1 and also shows up in project 2 apparently creating a duplicate.
Any suggestion?

Now when I drag and drop the photo no red # shows up and the photo stays in project 1 and also shows up in project 2 apparently creating a duplicate.
The projects are the basic containers. Each image and all its versions are in exactly one project.
You can use an image in many albums, without duplicating it, also in many products like books, screensaver, slideshows. But the projects are the basic structure of the library and you cannot have the same image in two different project, without duplicating it by storing the same original image files twice. Use albums to organize your library thematically.
Sorry, I misread your question. Dragging an image file between projects should move the image and all its versions to the other project. Aperture should only duplicate the image, if you hold down the alt/options key while dragging and move the image otherwise.
Which Aperture version are you using? And which MacOS X version? Is your profile signature "MacBook Pro with Retina display, Mac OS 9.2.x, Aperture 3.5.1" still valid?
In Aperture 3.6 on MacOS X 10.10.1 dragging between projects is still working as expected:

How can i transfer my music from one account to another on a different computer?

So i have an itunes account on dell laptop and i share that account with other famliy members. I recently bought a mac pro and wanted to create a new account that way i can use icloud, is there any possible way to transfer everything from my old library to my new one or will i lose everything i had on my phone and ipods? Or is it possible to have one account but multiple icloud accounts?

lisafromwindermere wrote:
I want to start my own account separate from my parents. Can I transfer my music from one account to another? If so, how?
Lisa,
Just get copies of the song files and add them to your iTunes library. With the exception of any DRM-protected files (purchased before mid-2009 and never upgraded) they will play fine, even though they are technically associated with the original account.

I want to start my own account separate from my parents. Can I transfer my music from one account to another? If so, how?

I want to start my own account separate from my parents. Can I transfer my music from one account to another? If so, how?

lisafromwindermere wrote:
I want to start my own account separate from my parents. Can I transfer my music from one account to another? If so, how?
Lisa,
Just get copies of the song files and add them to your iTunes library. With the exception of any DRM-protected files (purchased before mid-2009 and never upgraded) they will play fine, even though they are technically associated with the original account.

Can I transfer my itunes from one laptop to another?

Can I transfer my itunes from one laptop to another?

Yes.
From your OLD computer...
Copy your ENTIRE iTunes FOLDER to an External Drive... and then from the External Drive to your New Computer..
Full Details Here > http://support.apple.com/kb/HT1751
An Added Bonus is that you will have a Backup of iTunes.

I have no problems copying iMovie Events from one Mac to another, however, how can I copy iMovie Projects from one Mac to another?

I have no problems copying iMovie Events from one Mac to another, however, how can I copy iMovie Projects from one Mac to another? Any help will be appreciated. Thank you.

This should give you some good insight, I'd probably store them on an External HD on the old machine and then just drag and drop to the new machine.
https://discussions.apple.com/docs/DOC-4141

How can I script moving paths from one file to another?

Hello. I have 1 image with various color correction layers. The other is the exact same size but only contains paths. How can I script moving paths from one file to another? Thanks, in advance, for any help you can offer. Thanks!

Thanks! This one actually worked for me. Thanks for your help.
http://forums.adobe.com/message/3305389#3305389

How can you move the objects from one server to another?

how can you move the objects from one server to another?

Hi,
Collecting objects for Transporting
1. rsa1->transport connection
2. left panel choose 'object type', middle panel choose 'infocube' and 'select objects'
3. then choose your infocube and 'transfer'
4. will go to right panel, choose collection mode 'manual' and grouping only 'necessary objects'
5. after objects collection finished, create request
6. If they are $TMP, then change the package.
7. When you click the Save on the change package, it will prompt for transport. Here you can provide an existing open transport request number, or if you like here itself you can create a new one.
8. You can check the request in SE09 to confirm.
Releasing Transport Request
Lets say you are transporting from BWD to BWQ
Step 1: In BWD go to TCode SE10
Step 2: Find the request and release it (Truck Icon or option can be found by right click on request #)
Note: First release the child request and then the parent request
Steps below are to import transport (generally done by basis )
Step 1: In BWQ go to Tcode STMS
Step 2: Click on Import queue button
Step 3: Double Click on the line which says BWQ (or the system into which transport has to be imported)
Step 4: Click on refresh button
Step 5: High light the trasnport request and import it (using the truck icon)
Transport
http://help.sap.com/saphelp_nw2004s/helpdata/en/b5/1d733b73a8f706e10000000a11402f/frameset.htm
http://help.sap.com/saphelp_nw70/helpdata/en/0b/5ee7377a98c17fe10000009b38f842/frameset.htm
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/media/uuid/224381ad-0701-0010-dcb5-d74236082bff
Hope this helps.
thanks,
JituK

Can't see all devices from one AccessPoint to another? What is best setup to extend wireless coverage?

Similar Messages

Maybe you are looking for