Can't see wifi networks or connect to my own?

I'm going to start by saying I have an iPhone 4s and it's not that old, and the version is 6.1.3. So about two days ago, I started to notice that my wifi wasn't on. I was using my data in my house. I went to go turn my wifi on and off, and then I noticed I couldn't even see the networks around me, not even my own. So I waited to see what would happen. It came back by itself for about a minute, and then I was using my data again. I went and I updated my phone to the latest version, because I haven't done so in forever, and it didn't work. I reset my network settings or whatever, and that didn't work, instead it just dimmed out the wifi so I couldn't turn it on, but I waited for about and hour and it was fine. I went back into the wifi settings and the networks were back, so I tapped on mine, enterend the password, and it said 'Unable to join.' I tried it several times, I even checked if I put the password in right and I was. I also tried turning my phone off and on, and it didn't work. I really just want to throw my ohone at the wall. This is making me extremely angry because I don't know what else to do. And I am not about to contact Apple Support.

Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new).  Try each of these in order until the issue is resolved.
If the problem continues, take the device to Apple for evaluation and possible replacement.  Honestly, it sounds like the Wi-Fi chip is failing.

Similar Messages

  • Can't see wifi network

    Today I got a wimax modem with built in wifi (greenpacket DX230). There is no customization of the device at all. The SSID and password are already printed on the device and are supposed to work without setup. However, I cannot see the network from my macbook running snow leopard, even if I am right beside the device. I have checked several PCs and they can all see the network, and my iPods can also see the network. I have yet to try another mac (will try tomorrow).
    Does anyone know why this would be? I thought wifi was a standard and that there is no deviation from it? Why would my ipods be able to see the network but not the macbook? Kismac doesn't even show the network

    GShumway wrote:
    I cannot see the network from my macbook
    It might help to reset the connection settings on your Mac using these steps one at a time until the problem is resolved, recognizing that, depending on your problem, not all of these steps will make sense:
    1) Use the AirPort menu bar item to turn AirPort off, then on again.
    2) Try to select your Wi-Fi network from the AirPort menu.
    3) In the Network panel of System Preferences delete the AirPort item from the left column, then add it back.
    4) In the same panel as (3), define a new location and see if you can make that work.
    5) In the same panel, select the AirPort connection item, click the "Advanced" button, select the "TCP/IP" tab, then click "Renew DHCP Lease".
    6) In the folder /Library/Preferences ( not <yourhomefolder>/Library/Preferences), move the folder SystemConfiguration onto the Desktop, then restart your computer. See if you can now make your AirPort connection work.
    They may not help, but they'll only take a couple of minutes to try. Before you try these, if you have any special network settings on your Mac for things like DSL credentials, note all your network settings, because the latter steps will destroy them. If you got all the way to the last step, if things don't work any worse than before, you can trash the saved SystemConfiguration folder.

  • IPhone 4S - iOS 6 - can't see WiFi networks

    I have a strange problem with my iPhone. It's a locked iPhone, bought from Vodafone from my country. I use it locked and un-jailbreaked. I went in France for 2 weeks where i had my Roaming active, but i didn't used cellular data, only WiFi. Now, back home in my country, it seems that i can't see wireless networks. I tried to reinstall, update to the last firmware, it seems that wireless appear for 1 second when at first start, then it disappears and i can't see no more WiFi networks in list, tho there are like 10 networks around me.
    Any ideas? Or someone else had the same issue?
    Thanks,
    Nick

    i went to Vodafone. They said they will replace it. It seems like a manufacturing defect.

  • Can't see wifi networks?!

    Unlike any phone I've ever had before, whenever I switch on wifi on my E4G, I cannot get an automatic list up of available networks in the area. Instead, I have to go to Settings/Wifi/ to see what is available and THEN choose from them. After that, I can connect no problem. I've never had this before and am presuming it can't be built so that you have to do that every single time whenever you switch it on?! I'm used to switching on wifi and, unless you have a saved network in range which it connects to automatically, a screen pops up showing you all networks within range so that you can then select one, which is the normal way of choosing a new one when you go to a pub/restaurant etc., so that you can then put their passkey in to store it for future visits. Please don't tell me this phone is so backward that it's missing what even the most basic phones do as standard for something as important as wifi??  The only thing I can presume it might be is if I go into Settings/Wifi/Menu/Advanced, there is a tick box at the top saying Network notification. I am a bit loath to think it's this as there is smaller text underneath saying 'notify me when an open network is available'. To me, that reads that it'll tell me when an unsecured network, free to simply use at will, is available but am I reading that incorrectly and an open network may well be locked/password protected, and not just one that's free?

    This phone is designed to connect to trusted/saved WiFi networks by default and will do so whenever WiFi is turned on. It will not show a list of available networks when WiFi is turned on.
    The setting you've found (Setting/Wifi/Menu/Advanced/Network notification) will tell you when a unlocked/open network is available - it won't tell you if a network is available if it's protected with for example WPA. 

  • MacBook can't see wifi network

    Hi there,
    Please help! I'm setting up a wireless network and my macbook can't see the wireless network.
    The bizarre thing is that my friend's macbook sees it and connects with no problem. My macbook sees other wireless networks, but not mine! What's going on?!
    I have done the following
    - checked that it's turned on. (turned airport off, and back on, and restarted the computer)
    - checked that the router is broadcasting the SSID
    - checked the network name and password are correctly entered.
    - tried entering the name/pwd directly into the "preferred networks" setting of the Network Preferences pane
    what else could I do? I'm at a loss.
    Please help.
    thanks!

    Solved my own problem.
    Although the wifi router was set to broadcast the SSID (and only one of my macs could see it), I changed the settings so it was NOT broadcasting the SSID, then plugged the appropriate settings into the System Preferences pane, and it worked.
    crazy. but it works.

  • Macbook Pro can't see wireless network or connect to it, but iPhone can!?!?

    ok here"s the deal:
    I got my macbook pro in the states through school and it has been working fine ever since. I now just moved back home to Germany and for some odd reason the wireless network at home at my mom's won't appear in my "join network" list.
    I have tried diagnostics and advanced stuff, I have even typed in the network name and password into my preferred networks list manually... still nothing. When I connect the computer through an ethernet cable it works just fine. also searched and updated all my updates in case that was maybe the issue...
    here's the clue. my sister and her friend both also have macbooks (not pro's though) and both also run leopard and both of their laptops can see and connect to our wireless just fine. ALSO I have an iPhone, I purchased in the states and it can see and connect without any issues as well..
    I have called the German Apple support people, but they are absolutely useless and there are exactly 2 (!!!) genius bars here in Germany. one 4h and one 6h from where I live... sighs
    this is what I found in my about section, in case anybody knows what this means:
    +AirPort Card Information:+
    +Wireless Card Type: AirPort Extreme (0x14E4, 0x8C)+
    +Wireless Card Locale: USA+
    +Wireless Card Firmware Version: Broadcom BCM43xx 1.0 (5.10.91.21)+
    is it because it says "USA" and I am now in Germany? but how stupid would that be? other people that bring their American macs over don't have issues either... right???
    so yeah... HELP??? ANYBODY??? PLEASE???

    Hello,
    I had the same problem when I was traveling with my 2009 Macbook Pro. I am on a French ship and my MacBook was bought in the US. We have a wireless gaming network to play Call of Duty on that is set up on a LinkSys router. I was so frustrated because everyone else here could connect and play without a problem. My iPhone would even connect to the network but my MacBook Airport card wouldn't even recognize the network.
    It turns out that some countries use different Wifi channels. The Airport card in the US MacBook Pro is setup to only recognize channels 1-11. The European LinkSys router was broadcasting on channel 13 which is why my MacBook couldn't even see it. I changed the wireless channel on the router to 10 and now everything works great. I hope this works for you.
    Cheers
    P.S. - The US MBP can only recognize channels 1-11 on a standard 2.4GHz network. To see what channels your Airport Card will recognize, open System Profiler (located in the Utilities folder) and find the "Network" heading in the column on the left. Click "Airport" and it should display all of the supported channels in the info box to the right.
    Message was edited by: seanwich

  • Can't See Wifi Network At All w/ iBook..No Prob w/ Windows

    The computer in question is a 12" iBook 1.33GHz model. There are several computers connected to a 3rd party router, and the iBook is the only computer not seeing the wireless network at all. Everything worked fine up until 4 days ago. No changes were made. Is the a firmware update or anything I need to do my my Airport card?
    Everything has been reset with still no luck.
    What else can I do?

    This is actually for a friend, but she has not been around another wireless area. We can see the Airport Card in the system profiler. The firmware version is 404.2(3.90.34.0.P16).

  • TS1398 after upgrade to ios 6.0.1 WIFI is very weak or can not see WiFi networks (iPhone 3GS)

    Is there a way to restore the WiFi functionalilt of the iPHONE 3Gs after itw was upgraded to IOS 6.0.1 ?
    I see there are lots of things on the internet, but nothing that actually works !

    rzulfikar wrote:
    Thanks Chris for your solution.
    But just for you know that I bought Apple to get the 'after service', they should've warn the users not to upgrade to a higher OS if it can caused the phone 'dead'. Mine was totally unusable when it's just been upgraded. It stayed in the recovery mode and couldn't be restored. So I brought it to the nearest store and they did that to me, and eventually the phone is working, only it cannot detect my SIM Card...
    The problem is not about upgrading an iPhone to a newer version of iOS.  Your problem was upgrading a hacked phone, one of the well known consequences of which is re-locking and/or bricking the entire device when restoring in iTunes.  You chose to hack your phones firmware and operating system, so you must accept the consequences of going outside the bounds of normal use that Apple prescribes and supports.
    Had you not hacked it in the first place, you likely would have never had a problem, and if you had, Apple would have offered support to deal with it.  Your choice, your decision, your consequences.

  • Hi folks, you might know how to fix this: my wifi shows (no hardware installed) then I went to system preferences and deleted the wifi connection, I went also to system information and I can not see wifi listed on Network, how can I create a new wifi ?

    Hi folks, you might know how to fix this: my wifi shows (no hardware installed) then I went to system preferences and deleted the wifi connection, I went also to system information and I can not see wifi listed on Network, how can I create a new wifi or simply solve this, I have tryied shotdown pressing keys like P and R, option, etc. Please help me .

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
    Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output on certain models. The next normal startup may also be somewhat slow.
    The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

  • I updated my iphone 5 to ios 6.0.2. my wifi says its connected but doesn't work now. It doesn't matter what wifi network I connect to. It worked before updating my phone. I can no longer use facetime or use wifi at all. I'm not sure what to do to fix it.

    I updated my iphone 5 to ios 6.0.2. my wifi says its connected but doesn't work now. It doesn't matter what wifi network I connect to. It worked before updating my phone. I can no longer use facetime or use wifi at all. I'm not sure what to do to fix it.

    I'm having similar issues with my phone.  I got my first iPhone recently, only had an iPod touch gen4 for a little over a year.  Updated to 6.0.2 when we got the phone (iPhone 5) a few days before Christmas.  When I got home on the evening of January 11, my phone would not connect the router anymore.  I was able to get it to connect after resetting the phone and the router, updating the router, and manually connecting.  That laste for a few minutes and then wouldn't work anymore.   I live in an area with very limited service, we have a network extender installed to help, and I am barely getting a 3G signal at times.
    My wife's iPad 4, my touchiPod 4, and all of our laptops are working just fine on the router.  When I dropped my kid off at school today, I noticed that I am not even seeing the school network anymore from the parking lot where before I got 3 or 4 bars and could connect to their wifi when I was there.  Today my phone goes back and forth between seeing my home network but not connecting, to not even seeing the network at all even from the same room that the router is in.
    Hope Apple fixes this problem soon..............

  • How can i see which devices are connected to my wireless network?

    how can i see which devices are connected to my wireless network?

    Login to your router and view the DHCP clients.

  • Can´t see my Networks adapters in the Device manager!

    Help!
    I´m using Yoga 2 pro/windows 8.1
    I can´t see the Networks adapter in the Device manager?!
    (and no internet/WIFI connection is not working any more)
    I´ve tried to install the latest Wireless Driver from lenovos homepage but it there is still problems. The laptop still can´t find any network adapter and the wifi connection doesn´t work, as it did last week!
    Any one who has the same exeperience/or knew how to deal with these kind of issues?
    /Rasmus

    hi Rasmus,
    Can you try these steps:
    1. Check if you have a Network Controller entry in the Device Manager and follow this guide to get the hardware ID and on how identify the device.
    2. If there's no Network Controller entry in the Device Manager, then it's possible that the Wi-Fi card might have been disabled.
    Things to try:
     - Boot into the BIOS either by pressing Fn+F2 on boot-up, the OneKey Recovery button, or via the UEFI Firmare Settings. 
     - In the BIOS, navigate to the Configuration tab and disable the Wireless setting  hit Fn+F10 to Save and Exit then shut off the machine. 
     - Boot back into the BIOS and enable the Wireless setting then hit Fn+F10 to Save and Exit and observe if you can now detect wireless networks.
    Let me know how it goes.
    Regards
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • IPhone Can not see home network

    Ok, I have read a lot of strings about Wii issues and I have tried the following:
    - Unplugged (rebooted) my cable modem
    - Unplugged (rebooted) my Airport Extreme
    - Rebooted my iPhone multiple times
    - Turned on and off the Airplane Mode to re-search for WiFi connections.
    - Searched manually for the connection (typing in name and password)
    - Turned off the WAP/WAP2 Personal security
    but nothing seems to work. I can not view my home network on my WiFi.
    I can see all my neighbors networks and the phone works great on free networks around town but my home network will not show up.
    My home network does work on my laptop though.
    Any thoughts?

    Nathan:
    Great suggestion. I changed it to 802.11 n (with b/c compatability) and I can now see the network on my iphone and I can log in (I think).
    I chose the network from the list and put in the password. The first couple of times it did not take but the 3rd or 4th time it seemed to log on. If I go to Settings and look in the Wi-Fi area it has my network name as the network it is logged into but...
    There is no WiFi symbol on the top bar of the phone (only an E, for the Edge network) and when I chose any application (Safari, YouTube, etc.) it only accesses through the Edge network.
    Any other thoughts?

  • After install of 2.0 Playbook can't see WiFi and Bridge Apps won't execute

    Last weekend I finally bit the bullet and installed 2.0. I installed over WiFi but after the install the Playbook could no longer detect my D-link router (DIR-825). My Bold 9700 WiFi connection is fine. Also, I updated the Bridge software on my phone and the Playbook recognizes the connection but none of the Bridge Apps activate when I touch their respective icons. I've rebooted (3 finger) several times to no avail. I also tried manually connecting to the WiFi but without success. There also seems to be considerable battery drain compared to the 1.0 release despite keeping the Playbook in standby. I assume I'll have to re-install 2.0 and would appreciate any other suggestions as well as any guidelines on re-installing to ensure success and to avoid loss of apps and data. I did a full backup prior to the 2.0 install and will do another data backup prior to reinstalling.

    Since we upgraded the software, nothing but trouble. Can't see wireless network, can't connect manually to the computer (to copy files off), can't connect to wireless manually. Totally useless.
    Can ANYBODY help?

  • Playbook OS 2.0.0.7971​, Android Player can't see WiFi

    Hello Everybody,
    Yesterday I got my Playbook. During setup I got updated to OS 2.0.0.7971. Visited Playbook appstore and installed Wattpad (which apparently is an android app that runs on the integrated Android Player (not available as a separate app anymore)). Everything works all right except that it cannot see my WiFi connection and hence, cannot do anything useful. I also sideloaded Kindle, Pulse reader, and some other apps that run on the Android Player. NONE of them can access the internet (can't see the WiFi). As a result, I cannot even register my Kindle app.
    Anybody having similar issues on the OS 2.0.0.7971? I think my Android Player version is 2.0.0.56 (that is what it shows at the bar below). Please suggest what I should do to fix these. Without the Kindle app, the whole Playbook thing kinda becomes pointless to me :-(
    Please help.
    Thanks and Regards,
    Aditya

    Since we upgraded the software, nothing but trouble. Can't see wireless network, can't connect manually to the computer (to copy files off), can't connect to wireless manually. Totally useless.
    Can ANYBODY help?

Maybe you are looking for

  • Reading a pdf file from URL into Byte array/ByteBuffer in an applet.

    I'm trying to figure out why this particular snippet of code isn't working for me. I've got an applet which is supposed to read a .pdf and display it with a pdf-renderer library, but for some reason when I read in the .pdf files which sit on my serve

  • Scene selection buttons don't work in preview

    I edited my movie in iMovie, provided chapter markers that work in iMovie.  "Shared" the completed project to iDVD, which created scene selection buttons for all of the chapter markers and for the beginning. Now that I have dropped loops onto the but

  • Handling Multiple Host GS ID in SOA 11g B2B

    Hi, Greetings to B2B Gurus !!! We have a requirement to map different Host Group Interchange ID based on Input data and we are getting an error saying that, not able to identify the Trading Partner since the values are same. We have already added bel

  • How to handle shortcut key options in LabVIEW

    Hi, I want to handle the ctrl+c option for a string control in labview. I just want to prevent the user from pressing the ctrl+c button for copying. is it possible to handle that inEvent Structure? Thanks Alagar

  • Regarding Service Registry classification - PI7.1 EHP1

    Hi, We are trying to implement the Services Registry classification in PI.So far,we have published the wsdl in SR and have classifed it by going to the Manage tab in the SR and adding the Value Description,Value Code under a Classification system. As