Can't set up D-Link phone adapter DPH-50u on Windo...

I am moving my phone adapter to another computer running Windows 7.  Install and everything goes well, but the adapter can't communicate with skype, for some reason.  Tray indicator is red.  I have tried different combinations without success.
Any help would be appreciated.  The adapter is great once installed successfully, but installation is always a problem.  I have installed for friends as well, but always a big deal.  Right now I am frustrated, and thought possibly someone has some suggestions.
Thank you
Leon
*edited for privacy*

I had the same problem.
I don't know whether or not it was a coincidence, but I did the following:
Use a computer to Logon to www.icloud.com.
Go into Account Settings.
Click on Advanced.
Then click on logout of all browsers.
I was then able to log into My AppleID and start the two step authentication setup. When I added a new phone, it sent an SMS and it then prompted me for the 4 digit code.
Again, not sure whether this is a coincidence, but I never received the prompt to enter the 4 digit code until I accessed the iCloud website and followed the above steps.

Similar Messages

  • HT204053 can i set up two different phones on my computer to use i-tunes ?

    Can i set up two different phones with two different ids on my computer to use i-tunes?

    You can, and there are different ways to do it : http://support.apple.com/kb/HT1495

  • Is it possible we can to set button cornor link text?

    is it possible we can to set button cornor link text?

    @welcomecan,
    Your question is not clear to me ...Will you please elaborate..??
    Thanks,
    Bhasker

  • Trying to choose iCloud backup on my new phone as I lost my previous one but it states"no iCloud backups are compatible with this version" therefore I can't set up my replacement phone! Any suggestions

    Trying to choose iCloud backup on my new phone as I lost my previous one but it states"no iCloud backups are compatible with this version" therefore I can't set up my replacement phone! Any suggestions

    You can't restore a backup that was made on a device running a more recent version of iOS.  If your replacement phone is running iOS 6.0.1 and the one you backed up was running 6.1.2, for example, you would have to update your replacement phone before you could restore to the backup.  If this is the case, update your phone by connecting it to your computer, and selecting Check for Update or Update on the Summary tab of your iTunes sync settings, update the phone and set it up as New.  Then go to Settings>General>Reset, tap Erase All Content and Settings, go through the setup screens again and choose Restore from iCloud Backup.  You should then be able to restore your backup.

  • Can I set up a link (button or word) from a specific slide in a slideshow?

    Can I set up a link from a specific slide in a slideshow?

    Yes
    Turn off the "Edit Together" option.
    Navigate to the slide you want (turn thumbnails on temporarily if necessary).
    Select the area you want.
    Hyperlink in the normal way.
    Repeat until you have linked all the slides you require.
    Turn "Edit Together" back on.
    I think I had to link the caption separately as I couldn't find a way of selecting them together with the image or grouping them. Each slide links to a different page no problem.
    Peter

  • Can you set iphone alarm to phone calls only?

    when i had a blackberry you could set it to "phone calls only" in one simple step, so while you were sleeping you didn't get bothered by emails and texts, but still would hear the phone ring for emergencies.  can you set this easily on iphone with out having to uncheck all notifications etc?

    **** it!  thanks for the quick resposne...you would think for something that simple you'd be able to

  • Sender File Adapter Can I  set original MessageID like SOAP Adapter??

    Hello,PI Experts!!
    I want to set original messageID(GUID) to Sender File adapter scenario.
    SOAP Adapter can set original messageID with url, about FILE Adapter??
    I think Adapter Module maybe can set original messageID.
    best Regards,
    Yuuki Fujioka.

    Hello,
    Yes, you can get Message ID with any adapter.
    All neccessary information about approach you can find in links below:
    Use getTransformationParameters().
    Accessing Adapter-Specific Attributes
    http://help.sap.com/saphelp_nw04/helpdata/en/43/03612cdecc6e76e10000000a422035/content.htm
    Container Object
    http://help.sap.com/saphelp_nw04/helpdata/en/78/b4ea10263c404599ec6edabf59aa6c/content.htm (String Mapping Runtime Constants: MESSAGE_ID)
    Br,
    Dzmitry

  • How can I set a right link Aggregations?

    I have a Enterprise T5220 server, running Solaris 10 that I am using as a backup server. On this server, I have a Layer 4, LACP-enabled link aggregation set up using two of the server's Gigabit NICs (e1000g2 and e1000g3) and until recently I was getting up to and sometimes over 1.5 Gb/s as desired. However, something has happened recently to where I can now barely get over 1 Gb/s. As far as I know, no patches were applied to the server and no changes were made to the switch that it's connected to (Nortel Passport 8600 Series) and the total amount of backup data sent to the server has stayed fairly constant. I have tried setting up the aggregation multiple times and in multiple ways to no avail. (LACP enabled/disabled, different policies, etc.) I've also tried using different ports on the server and switch to rule out any faulty port problems. Our networking guys assure me that the aggregation is set up correctly on the switch side but I can get more details if needed.
    In order to attempt to better troubleshoot the problem, I run one of several network speed tools (nttcp, nepim, & iperf) as the "server" on the T5220, and I set up a spare X2100 as a "client". Both the server and client are connected to the same switch. The first set of tests with all three tools yields roughly 600 Mb/s. This seems a bit low to me, I seem to remember getting 700+ Mb/s prior to this "issue". When I run a second set of tests from two separate "client" X2100 servers, coming in on two different Gig ports on the T5220, each port also does ~600 Mb/s. I have also tried using crossover cables and I only get maybe a 50-75 Mb/s increase. After Googling Solaris network optimizations, I found that if I double tcp_max_buf to 2097152, and set tcp_xmit_hiwat & tcp_recv_hiwat to 524288, it bumps up the speed of a single Gig port to ~920 Mb/s. That's more like it!
    Unfortunately however, even with the TCP tweaks enabled, I still only get a little over 1 Gb/s through the two aggregated Gig ports. It seems as though the aggregation is only using one port, though MRTG graphs of the two switch ports do in fact show that they are both being utilized equally, essentially splitting the 1 Gb/s speed between
    the two ports.
    Problem with the server? switch? Aggregation software? All the above? At any rate, I seem to be missing something.. Any help regarding this issue would be greatly appreciated!
    Regards,
    sundy
    Output of several commands on the T5220:
    uname -a:
    SunOS oitbus1 5.10 Generic_137111-07 sun4v sparc SUNW,SPARC-Enterprise-T5220
    ifconfig -a (IP and broadcast hidden for security):
    lo0: flags=2001000849 mtu 8232 index 1
    inet 127.0.0.1 netmask ff000000
    aggr1: flags=1000843 mtu 1500 index 2
    inet x.x.x.x netmask ffffff00 broadcast x.x.x.x
    ether 0:14:4f:ec:bc:1e
    dladm show-dev:
    e1000g0 link: unknown speed: 0 Mbps duplex: half
    e1000g1 link: unknown speed: 0 Mbps duplex: half
    e1000g2 link: up speed: 1000 Mbps duplex: full
    e1000g3 link: up speed: 1000 Mbps duplex: full
    dladm show-link:
    e1000g0 type: non-vlan mtu: 1500 device: e1000g0
    e1000g1 type: non-vlan mtu: 1500 device: e1000g1
    e1000g2 type: non-vlan mtu: 1500 device: e1000g2
    e1000g3 type: non-vlan mtu: 1500 device: e1000g3
    aggr1 type: non-vlan mtu: 1500 aggregation: key 1
    dladm show-aggr:
    key: 1 (0x0001) policy: L4 address: 0:14:4f:ec:bc:1e (auto) device address speed
    duplex link state
    e1000g2 0:14:4f:ec:bc:1e 1000 Mbps full up attached
    e1000g3 1000 Mbps full up attached
    dladm show-aggr -L:
    key: 1 (0x0001) policy: L4 address: 0:14:4f:ec:bc:1e (auto) LACP mode: active LACP timer: short
    device activity timeout aggregatable sync coll dist defaulted expired
    e1000g2 active short yes yes yes yes no no
    e1000g3 active short yes yes yes yes no no
    dladm show-aggr -s:
    key: 1 ipackets rbytes opackets obytes %ipkts %opkts
    Total 464982722061215050501612388529872161440848661
    e1000g2 30677028844072327428231142100939796617960694 66.0 59.5
    e1000g3 15821243372049177622000967520476 64822888149 34.0 40.5

    sundy.liu wrote:
    Unfortunately however, even with the TCP tweaks enabled, I still only get a little over 1 Gb/s through the two aggregated Gig ports. It seems as though the aggregation is only using one port, though MRTG graphs of the two switch ports do in fact show that they are both being utilized equally, essentially splitting the 1 Gb/s speed between
    the two ports.
    Problem with the server? switch? Aggregation software? All the above? At any rate, I seem to be missing something.. Any help regarding this issue would be greatly appreciated!If you're only running a single stream, that's all you'll see. Teaming/aggregating doesn't make one stream go faster.
    If you ran two streams simultaneously, then you should see a difference between a single 1G interface and an aggregate of two 1G interfaces.
    Darren

  • Can I set a bookmarked link to open in the sidebar AND when a new page is loaded/originates from this page?

    Example: I have Google advanced search bookmarked and set to open in the sidebar. When I submit the search, I'd like it to open in the main view port. Is there a way to make links, POST/GET requests or otherwise any new page loads originating from the page loaded in the sidebar?

    So, if I remove a session var is there a way to test for its existence as well?
    Thanks,
    Chris

  • Help please .......can​'t set up email on phone.....​.

    Hi all,
    today i purchased my new phone and started to do the set up and well the rest is history......when i go onto setup-setup wizard-email setup, there is no option for adding a personal email account:/ how do i add a personal email account?
    Cheerz

    Do you have a BlackBerry Data Plan enabled on your account with your carrier or mobile provider?
    You must, in order to get the RIM push email functions you are looking for, as well as addtional BlackBerry data services such as the internet browser, Facebook for BlackBerry, BlackBerry Messenger, and much more.
    So, call your carrier and inquire about having the BlackBerry Data Plan added to your account.
    Good luck.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • How can I set a button/link that is visible on all slides?

    I want to add a button/link that is automatically visible on all slides (whole project). But it seems it does not work. Any help?

    Hello,
    It depends on your version. I hope you are on CP6 or later. In that case you have two possiblities:
    a shape button on the main master slide (and be sure that all daughter master slides have the objects of the main master slide)
    a shape button on the first slide, timed for the rest of the project.
    More details: Why I like Shape Buttons - Captivate 6! - Captivate blog
    There is also a webinar on demand from Adobe 'Lilybiri's favourite...'
    Lilybiri

  • How can i set up my evo phone to print on my hp 6500 officejet printer

    help-please - i already have the cloudprint app on my phone. don't have a clue where to go from here

    Hi,
    There are few applications around, please try this
      http://www.androidpit.com/en/android/market/apps/app/com.dynamixsoftware.printershare/PrinterShare-M...
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • How can I set ne2000 network adapter in Solaris 8 for x86

    I am a beginner. I can not set a ne2000 compatible network adapter(isa) in Solaris 8 for x86.
    I do follows:
    write the file ' /kernel/drv/nei.conf ' with ' name="nei" parent="isa" reg=0x1,0x0300,0x1f interrupts=10 '
    and use the command: drvconfig -i nei --failed
    use the command: drv_add -i nei; devlinks; --there is no the command drv_add
    use the command: touch /reconfigure; reboot
    after reboot, use the command: ifconfig nei0 plumb --failed
    Did I miss something obvious, or what driver should I use?

    After backing up the suspect hard drive, I ran Disk Repair on it and found no problems. Then ran Disk Warrior again and no problems. It is a Hitachi, btw.
    As for the PrefPane issue: Repairing disk permissions on the main volume and on the partition that holds the system did not make any difference.
    Reinstalled the 10.5.8 upgrade, performed safe start and then repaired permissions again. Still getting a blank PrefPane for network.
    Next step is to try and trash the System Configuration plist and Network Interfaces plist.

  • Can you set print from the samsung stratosphere mobil phone

    Can you set up the mobil phone  samsung stratospher to print to the hp officejet pro 8600?

     Bettielittle118, Hope you are doing well and welcome to the HP forums. 
    Yes you shoud be able to print from the Samsung Stratosphere as long as is running Android
    If what you want is to print from anywhere you must use HP ePrint go here to see how to start with this super free service. 
    This will give more control but it can be use only when the device and the printer are in the same network i.e. Home Network
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01616126&lc=en&cc=us&dlc=en&product=3857218
    You can say THANKS by clicking the KUDOS STAR. If my suggestion resolves your issue Mark as a "SOLUTION" this way others can benefit Thanks in Advance!

  • Where can i find contact support link or phone number even live chat?

    Where can i find adobe contact links phone number or live chat for to create PDF and billing

    Hi jewelryshopping,
    Thank you for posting on the Adobe forums, kindly follow the URL mentioned below to get the requisite.
    Contact Customer Care
    Thanks,
    Vikrantt Singh

Maybe you are looking for

  • Hard Drive Failure: Software or Hardware

    My computer stopped working recently. I had not installed anything new and nothing else changed, but one day I could not log in or even boot (grey screen spinning dial). Disk repair indicated I had an "invalid node structure: that was not repairable.

  • Adding a pre loader to an XML photo gallery between the photos.

    Hey, I have made a photogallery in actionscript 3 which uses an .XML file to import pictures. As the user clicks on the displayed image the code loads the next image in the cycle into the display. Now, I would like to add a preloader which displays t

  • FC Studio Crossgrade - now app won't launch!

    I just got my crossgrade disks yesterday and did the upgarde which took about 6 hours. I launched the app when it was finished, made sure it opened, looked at some old projects, quit, slept the computer all night. Woke up, did some email, shut down,

  • Label or Mark a Section of Video

    Is there a way to mark or label a section of a video clip?  I would like to create a searchable/filterable label for a specific start and end within a video clip.  If not, is there a workaround? Once created, I'd like to be able to filter on this lab

  • Burner not listed in output devices

    Just bought a new PowerMac with a factory installed PIONEER DVD-RW DVR-112D. While running DVDSP 4.0.3, I only have hard drive listed under output devices. I'm guessing the burner is compatible since it shipped with the computer...any suggestions or