Can`t setup my Ax88772a USB Fast Ethernet Adapter! Driver is already downloaded

Similar Messages

Apple USB to Ethernet Adapter??

Can you use the Apple " usb to ethernet " adapter with the airport express?

The USB port on the AirPort Express will only support a compatible printer, so using a USB to Ethernet adapter would not accomplish what you want to do.
If you add a simple 5 port Ethernet switch to the AirPort Express, one port will be used to connect to the Express with an Ethernet cable. You will then have 4 Ethernet ports available for devices.
Any major electronic/computer store will have what you need. Netgear or Cisco-Linksys make quality products.

I've bought an USB-to-ethernet-adapter and a minidisplay-port-to-VGA-adapter. But I can't use them at same time. At first, I plugged those two adapters and only the USB-to-ethernet worked. Tried restarting the mac then only VGA adapter worked.

I've bought an USB-to-ethernet-adapter and a minidisplay-port-to-VGA-adapter. But I can't use them at the same time. At first, I plugged those two adapters and only the USB-to-ethernet worked. I tried restarting the mac then only the VGA-adapter worked. I also tried to reinstall the OS.
I'm using new 13-inch MacBook Air early 2015. OS X 10.10.3.

Thanks Malcolm - Do you think it might be worth trying to flash the firmware on these cases - there seem to be updaters available on Prolific's website. Obviously I'd have to do it on a PC. I've emailed Prolific asking them about my problem. No reply as yet, and I'm not holding my breath! Do you know if there are any other posts on these boards relating to Prolific? Stupid question really - I'll just do a search...
Thanks again for your post. Cheers from Bonnie Scotland.

Third-Party USB to Ethernet Adapter not working since 10.8 updated

Hi I have a third-party USB to Ethernet adapter. Since the update of mountain lion the adapter does not work.
Is there a driver or something I can do to make it work?
Thanks

USB not so good, this very good.
Thunderbolt to Gigabit Ethernet Adapter

Unusual issue with tag engine and BELKIN USB to Ethernet adapter??

I have an .scf file with 72 tags and several tag groups in it. If I open the tag engine without the usb adapter, I can read the tag group names with the get group list.vi. The tag group names are listed in black letters when wired to an indicator. When I plug in the usb ethernet adapter, immediately the group tag names are greyed out in the indicator without even running the vi. If I put a tag constant on the block diagram and try to select a tag name with the pointer, no tagnames pop up. It worked yesterday and my IT. department sent down a shockwave and flash5 update download when I booted up this morning. anyone have any ideas??

I am still seeing the tag groups disappear when I start the tag engine on labview7.0. I have several other programs running at the same time, KEPWARE, PROWORX NXT, USB to ethernet adapter. This is on a win2000 machine.
Attachments:
op50_head_press_force_status_rev2.vi ‏320 KB
Process_Sta2_probe_results.vi ‏42 KB
op50_head_version2.scf ‏53 KB

I need a USB/FireWire ethernet adapter

About 6 months ago my ethernet port was fried when a lightning bolt sent a surge through the wire. Since then i have been using my family's wireless network, but now that I am back in school and away from home, i don't have that luxury. So, i've been looking for a Mac compatible USB/FireWire ethernet adapter and have had no luck. If anyone knows where I can find one, let me know.

Hi Kllru,
Welcome to the Discussions.
The following link has info on compatible adapters as well as a driver for OS X.
http://www.sustworks.com/site/newsusbethernet.html
John

HELP: USB to Ethernet Adapter

Hello Everyone. I have a USB to Ethernet adapter for my Macbook Pro Retina. After plugging it into an ethernet cable and connecting everything, my computer still isn't reading it. I am wondering if there is an install driver or what or if I am doing something wrong. Thanks you for your help.

Brb8910,
what is the brand and model of your USB-to-Ethernet adapter? Does the manufacturer claim that it is compatible with your installed version of OS X?

WRT 120N Wireless -N Home Router/PRO200WL PCI Fast Ethernet Adapter

PRO200WL PCI Fast Ethernet Adapter in my 10-year old Dell Dimension 8200 running XP is not recognized as a wired/compatible adapter by WRT120N. Installed router using a newer laptop but when I connect the PC it causes a nv4_disp file to go into an endless loop and shut the computer down. What to do?

The driver of the ethernet adapter of the PC might already be outdated judging from the age of the computer. I suggest you have the drivers updated.

I have an external hard drive, can I set a password on this? The drive is already populated with data

I have an external hard drive, can I set a password on this? The drive is already populated with data

ITs an old Iomega 100gb external HD that has about 90gb of music on it. The Macbook has a 500gb HD. I would like to put the iTunes library on the internal HD so I have room to expand.
Phil0124 wrote:
You can copy it to the internal hard drive as long as it fits on it. How big is your library, and how big is your internal HD?
The only thing you do not want to do is over-stuff the internal hard drive. The OS needs some space to operate correctly, so if your iTunes library uses up more than say 80 to 85% of the internal HD's available space it may not be a good idea to transfer it over.
With that said, the internal HD will provide slightly faster access to the library than the external would, but other than that, you can point iTunes to the external drive just fine.

I got internal error 2738 after trying to install the marvell yucon ethernet adapter driver

I got the marvell yucon ethernet adapter driver on the acer support page. My laptop is an extensa 5420-5038 with vista sp2 32 bit. My wired lan is not working but the wireless is. The version of the acer driver is 10.12.8.3 if that would help. I think uninstalling the old software for the adapter must have failed during installation and I don't know what to do. I don't know how to find any old applications or machine language software for the adapter in the computer to uninstall before trying again if that is what I have to do. Do I have to go to the command prompt and do something?

http://answers.microsoft.com/en-us/windows/forum/windows_vista-hardware/internal-error-2738-when-trying-to-update-marvell/ce07aa54-f6d2-4834-89c5-71b61877eb4e

Can't call out on PSTN after ethernet adapter failure in J4W

Hi all
Okay here goes.
We are currently deploying new laptops in our business. It's the brand new Lenovo X1 Carbon 2nd G. together with a USB based docking station. Unfortunately there is a very annoying bug with the docking station. The problem is that the dock ethernet NIC, suddenly disappears from time to time in Windows. This means that Jabber for Windows is failing over to the Wi-Fi network. This should be okay, but we are seeing an issue with J4W, when the ethernet NIC disappear.
The problem is that J4W can't call out to external phone numbers/PSTN, but all internal calls are working fine. Also it's possible to call from an external number/PSTN to the J4W client. But still, the J4W client can't call an external no. You will only hear a busy tone when trying to make an external call.
It doesn't help restarting the J4W client, we have to reboot the entire computer to make the client be able to call external numbers over Wi-Fi. Meaning that the ethernet NIC on the docking station, isn't reappearing after a reboot of the laptop. To make it reappear, we have to disconnect and connect the docking station cable.
Atm. we are waiting for a fix from Lenovo, but in the meantime I can't understand why we can't call external no. when the ethernet NIC fails. I mean, we can call external numbers. over Wi-Fi, but not when the ethernet NIC are failing.
Can anyone point me into the correct direction here?
Specs:
CUCM: 8.6.2.22900-9
CUP: 8.6.4.13900-4
J4W: 9.7
Gateway: Cisco 2911
OS: Windows 7 32 bit.

Hello Taxi-Anne,
Welcome to the forums.
Try following the steps below to turn off the call forwarding:
1. Touch Phone.
2. Swipe down from the top of the screen.
3. Touch the Settings icon.
4. Touch Call Forwarding.
5. Touch the required option (e.g., Forward If Busy).
6. Touch Save.
Let us know if this helps. Have a good day.
-SR
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Usb to Ethernet adapter doesn't work? AX88772B

I don't know how to make a connection with Internet with RJ-45 cable with the usb adapter.
I have MBA. Lion 10.7.5
Now I need to connect MBA by RJ-45 cable with usb adapter (asus AX88772B)
MBA see the adapter (even without an ethernet cable).
I also did download drivers from here http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=105;71;101&PLine=71
I read the instruction, and I've done 3 steps on the page 4 exept these one's:
(4) Set the permission access mode of Apple’s default driver.
(5) Update the access and modification times of ASIX’s AX88772B/772A/760/772 or AX88178 driver.
But i don't know how to do this.
In the system report is always written this:
AX88772B:
Product ID:          0x7e2b
Vendor ID:          0x0b95 (ASIX Electronics Corporation)
Version:           0.01
Serial Number:          09EF51
Speed:          Up to 480 Mb/sec
Manufacturer:          ASIX Elec. Corp.
Location ID:          0xfd120000 / 4
Current Available (mA):          500
Current Required (mA):          Unknown (Device has not been configured)NO
But still I can't make an Usb to Ethernet connection in system preferenes, nothing written about it there.

Hmm. Well I tried rebooting with wifi off but that didn't fix things for me. Would you mind sharing what your System Information says under Thunderbolt? This is what mine looks like:
MacBook Pro:
Vendor Name:          Apple, Inc.
Device Name:          Macintosh
UID:          0x0001000D1290C120
Firmware Version:          11.1
Port:
Status:          No devices connected
Link Status:          7
Link Controller Firmware Version:          0.11.4
Port:
Status:          Connected
Link Status:          2
Link Controller Firmware Version:          0.11.4
Thunderbolt to Gigabit Ethernet Adapter:
Vendor Name:          Apple, Inc.
Device Name:          Thunderbolt to Gigabit Ethernet Adapter
Vendor ID:          0x1
Device ID:          0x8003
Device Revision:          0x1
UID:          0x000100020059EBB0
Apple Serial Number:          DTN224606LWDWKHAX
Route String:          3
Firmware Version:          5.5
Port:
Status:          Connected
Link Status:          2
Port Micro Firmware Version:          0.0.8

Asix usb to ethernet adapter and netctl

Hello All!
I'm having difficulty in getting my asix usb ethernet adapter to work with netctl.
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: xxxxxxxxxxxxx
5: usbnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 00:0e:c6:88:fd:a1 brd ff:ff:ff:ff:ff:ff
# cat /etc/netctl/usb
Description='A basic static ethernet connection'
Interface=usbnet0
Connection=ethernet
IP=static
Address=('192.168.5.1/24')
journalctl output after running "netctl start usb"
Sep 30 15:07:14 faubourg systemd[1]: Starting A basic static ethernet connection...
Sep 30 15:07:15 faubourg network[3512]: Starting network profile 'usb'...
Sep 30 15:07:15 faubourg kernel: IPv6: ADDRCONF(NETDEV_UP): usbnet0: link is not ready
Sep 30 15:07:20 faubourg network[3512]: No connection on interface 'usbnet0'
Sep 30 15:07:20 faubourg network[3512]: Failed to bring the network up for profile 'usb'
Sep 30 15:07:20 faubourg systemd[1]: [email protected]: main process exited, code=exited, status=1/FAILURE
Sep 30 15:07:20 faubourg systemd[1]: Failed to start A basic static ethernet connection.
Sep 30 15:07:20 faubourg systemd[1]: Unit [email protected] entered failed state.
I can, however, manually bring the link up and set the ip address.
# ip addr add 192.168.5.1/24 brd 192.168.5.255 dev usbnet0
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: xxxxxxxxxxxxx
6: usbnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 00:0e:c6:88:fd:a1 brd ff:ff:ff:ff:ff:ff
inet 192.168.5.1/24 brd 192.168.5.255 scope global usbnet0
valid_lft forever preferred_lft forever
# ip link set dev usbnet0 up
faubourg netctl # ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: xxxxxxxxxxxxx
6: usbnet0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 00:0e:c6:88:fd:a1 brd ff:ff:ff:ff:ff:ff
inet 192.168.5.1/24 brd 192.168.5.255 scope global usbnet0
valid_lft forever preferred_lft forever
inet6 fe80::20e:c6ff:fe88:fda1/64 scope link
valid_lft forever preferred_lft forever
As can be seen, an autoconfiguration ipv6 address based upon my MAC address was automatically added with the ip link command. The lights on the device are still not on and it still fails to communicate. One more command fixes that.
# ethtool -s usbnet0 speed 100 duplex full
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: xxxxxxxxxxxxx
6: usbnet0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 00:0e:c6:88:fd:a1 brd ff:ff:ff:ff:ff:ff
inet 192.168.5.1/24 brd 192.168.5.255 scope global usbnet0
valid_lft forever preferred_lft forever
inet6 fe80::20e:c6ff:fe88:fda1/64 scope link
valid_lft forever preferred_lft forever
So my question is, how can I get netctl to do this for me automatically.

bump

MacAir - Apple USB Ethernet Adapter Drive

Hi,
im using macair, and trying to install bootcamp for windows Vista / XP. however, im having difficulties to download driver for Apple USB Ethernet Adapter. if anyone know where to download this driver, please advise me..

Welcome to Apple Discussions!
There doesn't seem to be a clear-cut answer to this. If you read the reviews on the Apple site, some people have been able to make the ethernet adaptor work on some PowerPC Macs, and others can't even get it to work on a different Intel Mac. I know this isn't much help, but a perusal of these reviews might be the best resource unless someone else has actually done this with the same iBook that you have.
I assume you have tried a different ethernet cable?
Good luck!

Why is this usb to ethernet adapter so cheap?

Hi,
I need an enthernet Adapter for my macbook air and found this one:
http://www.ebay.de/itm/USB-2-0-Adaptor-Ethernet-Adapter-Apple-Macbook-Air-brandn eu-Top-Qualitat-/170717342238?pt=Apple_Zubeh%C3%B6r&hash=item27bf8bea1e#ht_2389w t_982
is it original Apple?
Best regards,
Chris

Isn't that what it says? Apple's online price is $29.00 USD.

Can`t setup my Ax88772a USB Fast Ethernet Adapter! Driver is already downloaded

Similar Messages

Maybe you are looking for