Can't show the configuration on Cisco 4503-E
I have cisco 4503-E as my core switch. When I want to read or save configuration it show "NVRAM: Unable to read configuration. Try again later."
Somebody said the cause of simultaneous access to NVRAM. I use "show users" to see the access users but there are no other access, only me.
Can it be cause of hardware?
Please kindly provide the solution. Thanks.
Best regards,
Mano
The issue is triggered when you have a large configuration file and immediately after exiting the configuration mode you attempt to save the configuration in NVRAM. The issue is related to an internal timer event whose behavior cannot be modified.
If you give a sufficient time between an exit from configuration mode before saving the configuration the problem will not resurface.
You can also find one known DDTS - CSCtn46265 which explains the issue. Please let me know if you have any questions.
HTH
Regards
Inayath
*Plz rate if this info is helpfull.
Similar Messages
-
Hi All,
In VPN 3000 concerntrator, I've enabled tftp, telnet, snmp. I've also successfully added the concerntrator into Ciscoworks LMS 4.2.2. All the ports are verified open to Ciscoworks. No question mark shows next to this device in the device management of LMS. However, when I run configuration Achive Job, I always get the following failed message. Can anybody tell me how to to back up the configuration of Cisco VPN 3000 concerntrator in Ciscoworks LMS 4.2.2? Thanks in advance.Sorry, but apparently not. Please see the supported devices table (here).
That table states, among other things:
The following features are not supported:
Network Topology Layer 2 Services
Fault Management
Configuration Deploy Protocols: HTTPS, TELNET, SSH, SCP, TFTP, RCP
Configuration Fetch Protocols: HTTPS, TELNET, SSH, SCP, TFTP, RCP -
Can i transfer the configuration, my playlist from my ipod to itunes?.
Can i transfer the configuration, my playlist from my ipod to itunes.My PC was saved after infection from a virus.i had yto load again Itunes.
I saved the playlist but not the configuration,i copy the playlist in the new loaded itunes but is all disorganized ,can i recover my personal configuration from my ipod thta still shows my old configuration?
I tried to copy the setlist using my ipod as a USB but didnt work , i dont want to sync the ipod with the new configuration if there is a way i can still saved itSee Recover your iTunes library from your iPod or iOS device.
tt2 -
Error "can not start the configuration in parallel does not correct"
Hello everybody,
I have Windows 7 SP1, and when I install Business Objects 4.1 Client, it is install correctly but when i execute the program, for example BO Rich Client, an error appear "can not start the configuration in parallel does not correct" Could you help me?
Thanks in advance!Check this KB
1678498 - BI 4.0 Universe Designer Gives Side-by-Side configuration incorrect Error -
How can I show the chart in forms?
Dear all:
I want to create a line chart. I use the chart wizard and it is successful to create the chart. But, it can't show the chart when I run the form. How can I show the chart in form6i?
Besides, I see a document that refer to 'OG.pll'.
I can't find the OG.pll in form6i. Do I need 'OG.pll' to show the chart when I run the form? Thank you very much!!Hi Carlos,
You can try to create a code node for check which signature to print.
In global variable declare a variable ie named g_sign type TDOBNAME.
Then pass this var to name of graphics &g_sign&
please check and reply.
regards, -
Can LR show the numbers in Quick developement panel?
Try to use quick development panel, it is easy to use but for exposure, clarity and vibrance you cannot see how many stops you have adjusted.
Can LR show the numbers in Quick development panel?
Any comment?>tt688 - 6:49am Sep 23, 08 PST (#2 of 6)
>I think that Quick Deve function is useless if you can not see the how >many stops you have adjusted.
When LR first came out I did not "get" the Quick Dev function. Luminous Landscape have an excellent video tutorial for LR by Michael Reichmann and Jeff Schewe.
It explains that the QD function is there to allow you to make quick visual adjustments to images to assist in choosing picks / rejects and generally culling a shoot. Until you have the exposure / contrast / colour balance somewhere near correct, it is difficult to properly evaluate a shot. Using QD like this then makes sense, it's not supposed to duplicate or take the place of the develop module.
Note that the adjustments you make in QD are relative, that is if you select a group of generally underexposed shots and increase the exposure the amount will be relative to each shots original exposure level. -
How can i erase the firmware of cisco 7912 phone ?
how can i erase the firmware of cisco 7912 phone ? the firmware is crashed in this 7912 phone , i want it to download another copy from CUCM8.5 .
the way i did on 7911phone doesn't work on 7912.https://supportforums.cisco.com/discussion/10797901/reset-factory-default-ip-phone-7912
You can try that procedure but I'm not sure how far that factory reset goes on those phones. I know the 7940/60 series you can blow out everything except the CNU which would do exactly what you are looking for. -
How can i show the first item in the list as selected item
Aslam o Alikum (Hi)
Dear All
How can i show the first item in the list as selected item when user click on the list. Right now when user click the list the list shows the last item in the list as selected or highlighted. Furthermore if the list item have large no of value and a scroll bar along with it then the list scroll to last item when user click it with mouse. I want that when user click the list item with mouse list should show the first item as highlighted.
Take Care
Allah HafizHi!
You can set list "initial value" using When-Create-Record trigger.
I.g.
:<Block_name>.<list_item_name> := Get_List_Element_Value('<Block_name>.<list_item_name>', 1); -
how can I show the photos of the person that im calling? now that im using IOS 7 when i want to call someone the photo /imagine does not appear , how can i fix it?
iPhone 5, iOS 7jlfcba wrote:
IOS 7.1.1 doesn't show a "days to sync" parameter anywhere in SETTINGS/Mail,Contacts,Calendars/ACCOUNTS/GMAIL Account/ GMAIL Acccount Info. There is nothing in iTunes relating to such an option either. So, it seems I'm back to square one.
If you have a decent mail provider like Microsoft Hotmail or Outlook.com mail it does.
If you have Gmail it does not. Quite right. Gmail is rubbish. -
N7K can't save the configuration
The N7K can't save the configuration to startup, here is the error message, the box is running 5.0.5, see you idea if it
N7K-1# copy run startup-config
[########################################] 100%
Configuration update aborted: request was aborted
Log message
===========
2013 May 31 09:59:01 %SYSMGR-STANDBY-5-CFGWRITE_STARTED: Configuration copy started (PID 2547).
2013 May 31 09:59:02 %SYSMGR-STANDBY-5-SUBPROC_TERMINATED: "System Manager (configuration controller)" (PID 2547) has finished with error code SYSMGR_EXITCODE_SYSERR (1).
2013 May 31 09:59:15 %SYSMGR-3-CFGWRITE_FAILED: Configuration copy failed (error-id 0x401E0000).Hi Yeun,
Whats the firmware you are running:
There are couple of bugs been reported for this issue:
FIX IN: 5.1.2
1. CSCtj44206 N7K/5.1.1: copy runn start aborted due to timeout
2. CSCtx50294 Installer:copy run to start fails in specific setup when deployed as HA.
3. CSCtj92312 N7K Unable to save config following crash of res-mgr process.
4. CSCtj83417 ISSD fails or 'copy failed (error-id 0x401E0000)' error
HTH
Regards
Inayath
*Plz rate this post if this info is helpfull and mark the thread as closed if this info answered your query. -
I am having problems setting up airport extreme.
What ADSL modem do you advise to use with my new airport extreme? I have tried a basic TP-Link ADSL2+ modem and I can't get the configuration working. What modem does Apple recommend?Ok well I have looked around some more and have found this to be the most up to date official response to my question as seen at this link here:
http://www.actiontec.com/support/product_details.php?pid=41#q27
Can I Bridge the Actiontec MI424WR router that Verizon provided, when I signed up for FiOS service?
The MI424WR does not have a bridging option, and neither Verizon nor Actiontec support attempting to bridge it.
The desire to bridge the MI424WR is based on a misunderstanding that it is a modem as well as a router. Actiontec does produce DSL Gateways that have a Transparent-Bridging option, which bypasses or disables the router function and allows the Gateway to act simply as a DSL modem, when it is enabled. Many consumers do not realize that with FiOS, the ONT (typically outside the home) is the device that handles changing the FiOS signal from Fiber to either Ethernet or Coax, and that the Router is just a Router, and if it was bridged or bypassed, it would be a device without a function. For most Verizon FiOS customers their service would completely stop if the MI424WR was bridged, because the Video on Demand service is dependent on it to work.
If your ONT is connected to the Actiontec MI424WR router via Coax, the MI424WR is required due to the Coax connection. But if the ONT is connected to the MI424WR via Ethernet, then in most cases some other router can be substituted for the MI424WR, and it can be removed."
So it looks like I will be calling Verizon support to see about getting the Ethernet connection installed and getting another modem... -
Web publishing tool, I can't show the panel in embedded mode.
I don't know what happen but I have try every thing and still without the possibility to make a preview of my VI in the "web publishing tool" and also can't show the panel in embedded mode.
I can see the preview in the browser but it remain forever "downloading panel" and nothing more else happen.
Please help me because I don't find any explanation to this problem in Google.
Additional information:
1) I am using Labview professional development system 8.2 under Windows XP SP3 (it was the same under SP2), also in vista ultimate.
2) In the attachment I show that I'm using Mozilla Firefox but is the same problem under IE.I don't think the preview ever shown an image.
Ton
Free Code Capture Tool! Version 2.1.3 with comments, web-upload, back-save and snippets!
Nederlandse LabVIEW user groep www.lvug.nl
My LabVIEW Ideas
LabVIEW, programming like it should be! -
I am a Taiwanese. My iPod nano can not show the lyrics
My iPod nan can not show the lyrics.It will be like"ifhfjdghuiadhghjkbdbdjkbdgdnkjn589d567g564h54df+.......................... "
Why?
How to solve it?Right->click on these tracks in iTunes and choose Get Info. Then head to Lyrics tab. Are the correct lyrics listed there?
B-rock -
Jsp include can not show the full page
When i use jsp to include other jsp which have around 1000 lines. the included jsu can only show the last 500 lines. how can i solve lt?
Having JSPs of this size is very bad practice. You should design your solution so as to avoid this at all costs.
There is an upper size limit on JSPs which you may be running into here, check the JSP spec but it's something like 64k
Regards,
Gareth
(PDK team) -
I can not save the configuration sfe2000 linksys one
attempt to admin I can not save the configuration
and l1_admin I do not have accesI understand the error statement, but if you could provide more info we should be able to correct the problem.
When did this start?
Is this a new switch?
FW version?
Do you have RADIUS user authentication?
Anything that you may feel we should know.
Maybe you are looking for
-
Over Time Workflow Container elements not updated
Hi, I am using Standard Task TS20000459 for approval of Overtime entered for an employee in CAT2 transaction. Work item is getting generated to his manager's inbox. Issue is, subject of the work item should have employee number and Employe name. Stan
-
How to create a DataBase File like MDB or DBF to web
Hi People, I'm a Delphi Developer and I'm new in Java. I need to make a DataBase File like MDB or DBF to work online. I will make a Form to sign users. All of user's information, for example: user name, address, mail, phone, will need to record in my
-
Using a custom certificate store for SCCM 2012 clients and primary site server
I have read what seems to be all the pki related documentation out there for SCCM 2012. I have a PKI infrastructure up and running issueing certificates with an offline root through group policy autoenrollment. The problem that i'm faced with is we a
-
Bridge Browser and WiFi Browser Issues???
Hey everyone, I've had my Playbook since day one and I have been having issues that I can't seem to get resolved involving the Brdige Browser and WiFi browser. On the Bridge Browser I can't browse to any webpages. I simply get a non-descript "Not Aut
-
How to remove recently deleted photo album off iPhone by iTunes?
Using iTunes how can i remove the recently deleted photos from my iPhone 4s?