Can't upload from more than one card

I recently upgraded to Snow Leopard, and now when I use Aperture 3, either in 32-bit or 64-bit mode, I can upload images from one of my CF cards just fine, but if I try to upload from a second card, everything looks like it's going to work fine, but then it doesn't upload any of the images. I have to quit and restart A3 and then it works fine for a card or two, and then the same thing. Any suggestions?

It is never recommended to erase memory cards in Aperture or any photo application. Best to Reformat in the camera. Can lead to errors saving in the camera, or maybe reduce recognizable free space for the camera. Perhaps it even has some lingering impact as you erase one card, and then immediately try to download from a new card?
I go a step further, and never eject the card in Aperture, but rather wait to eject with the Finder. This is due primarily to the fact that I use a Firewire CF reader, and had some suspicions about release of Firewire devices in Snow Leopard.
I would recommend that you cycle two or three cards where you wait and reformat in the camera, and then see if this behavior persists. I have never encountered any balkiness going from one card to other where I have need to download from multiple cards after shooting.
Ernie

Similar Messages

  • Can I acquire from more than one device at once using Labview?

    I have two SC-2345 boxes. One is device 3 and one is device 4. Can I acquire from both of these boxes at once? I know for most of the AI functions you just put in one Device number. But what if I want to acquire from 32 channels at once? How would I do this? Your help and tips are appreciated.
    ALSO- If you know about SC-2345 boxes, how many Analog input channels can I use? I see 8 slots for AI and the other 8 appear to be for signal conditioning. Can I still use these for AI? Could I have 16 thermocouple modules in one box?
    THANKS!
    Lauren

    Lauren,
    Yes, you can simultaneously acquire from both devices. However, each device will require its own analog input task. Furthermore, if you want to synchronize the acquisitions, you will need to connect the DAQ devices that are cabled to the SC-2345s with a RTSI cable. Below, I have included a link to a KnowledgeBase detailing RTSI:
    KnowledgeBase: What is RTSI?
    In order to understand the required programming structure, you may want to examine the following examples that are available in LabVIEW (one uses NI-DAQmx and the other uses Traditional NI-DAQ):
    NI-DAQmx
    Multi-Device Synch-Shared Timebase-Cont Acquisition.vi
    Tradi
    tional NI-DAQ
    Two E-Series Shared ScanClk.vi
    With regards to your second question, the SC-2345 provides access to 16 analog input channels through 8 modules. Most analog input modules have two channels. However, both of the SCC-TC series thermocouple input modules only have one channel because the other is used for the built-in CJC sensor. Thus, using the SCC-TC series modules, you will only be able to acquire from eight thermocouples with a single SC-2345.
    Good luck with your application.
    Spencer S.

  • Does anyone know of an app that is for invoicing that can be accessed from more than one iPad at a time?

    I have a roofing business with my husband and we both have iPads we need a invoicing program app that we both can use and see the same material on both iPads is there any apps that anyone knows of that can do this?

    You'll need a program that can open and edit the invoices. You can search the app store for "invoices" and see what you can find - perhaps there is a cloud-based one that would allow you to store the invoices on their server.
    Or if the apps are fairly simple, you could open them in a Word Processing app that does sync two ways with the cloud and do your work on them - and then store the receipts in Dropbox/iDisk/Sugarsync. Loading the actual documents onto those services is very easy and self-explanatory once you sign up for them.

  • Can takes from more than one track be comped at the same time?

    Greetings,
    I know that this question has been asked recently in this forum (http://discussions.apple.com/thread.jspa?messageID=9527542&#9527542), but I don't think that the respondents completely understood the question... Or perhaps I did not understand the suggested solutions to the problem. I will ask the question in a slightly different way...
    Suppose that I record guitar with 2 microphones (a pickup mic, and a room mic). The first microphone is recorded onto track 1, the second microphone is recorded onto track 2. Multiple takes are done in this manner. When it comes time to comp the tracks, how is it done? Can the takes from more than one track be comped together at the same time? I have tried to do this by grouping both tracks together, but it does not work.
    Any suggestions?
    Thank you.

    You had the right idea grouping the tracks together. You must make sure that in the group settings, the box titled "region selection (edit)" is checked. This will allow you to make the same cuts (or in this case, swipes) on all regions in the group.

  • HT1206 Can I have in one iphone 5 music from more than one itunes accounts?  My daughter and I have our music in the same pc. She and I have iTunes accounts. I have not been able to load in my ophone with my itunes acct music that she purchased in her acc

    Can I have in one iphone 5 music from more than one itunes accounts?  My daughter and I have our music in the same pc. She and I have iTunes accounts. I have not been able to load in my ophone with my itunes acct music that she purchased in her account.  I have not been able to do this. Thanks

    iTunes Match is not sharable across Apple IDs. The best way to get the music on her iPad is to leave hers signed into her Apple ID on the iTunes Store and sync via USB.

  • How do I send pictures from iphoto to a group via email instead of to just one individual? I can't type in more than one name or send the pictures to a group.

    How do I send pictures from iphoto to a group via email instead of to just one individual? I can't type in more than one name or send the pictures to a group.

    I had a similar problem in that my wife's iphone 5 could not send pics with imessage.  Had to set the settings to default to SMS or whatever.  After laboring many hours on the web I coincidentally was on the phone with the internet people to question my internet speed.  They changed the router channel, which is something that I am capable of doing myself.  After that, the pics go over imessage.  My own Iphone didn't have the problem.  We are both latest IOS 7.0.6.

  • Can a master data will have loading from more than one data source

    Dear gurus,
          I have a master data object which has every day loading from one particular data source. Now I got a requirement to load data from another data source. If we load data from more than one data source , will there be any problem with data? Will it accept loading from more than one data source.?
    Regards
    Rs

    Hi Ram,
    We can load the data to target morethan one datasource.Thats advantage in BI compare to BW. It will accept loading from more than one datasource.but you have to take care about characteristic and attributes are the same in both datasources like that.
    Regards,
    SVS

  • HT4859 can you back up pictures from more than one phone

    can you back up pictures from more than one phone

    Welcome to the Apple Community.
    Yes, you can back up multiple devices but may need to purchase more iCloud space.

  • Switched from DSL to cable modem. My Airport light won't turn green. Keeps blinking orange. No wireless now and can't connect to more than one computer! ?????

    Switched from DSL to cable modem. My Airport light won't turn green. Keeps blinking orange. No wireless now and can't connect to more than one computer! ?????

    Hmmmm.
    If you reset the AirPort Extreme by holding in the reset button for 9-10 seconds and then releasing, the AirPort should be back in default settings which would allow mutliple computers to connect to the LAN ports on the AirPort.
    Power off the cable modem for now and leave it off at least 15 minutes.
    With the AirPort Extreme still powered on, hold in the rest button on the back for 9-10 seconds and release. Allow a full minute for the AirPort Extreme to restart to a slow, blinking abmer light.
    Then, power off the AirPort Extreme.
    Check to make sure that the Ethernet cable from the modem is connected to the WAN "O" port on the AirPort Extreme.
    After the modem has been powered off for at least 15 minutes, power it up and let it run for 5 minutes by itself.
    Now, power up the AirPort Exteme and let it run for 2-3 minutes
    Open Macintosh HD > Applications > Utilities > AirPort Utility
    Connect an Ethernet cable from your Mac to one of the LAN <-> ports on the AirPort Express
    Click on the AirPort Exteme, then click Continue to follow the guided setup tp configure the AirPort Extreme.  You can use the same wireless network name, password, etc that you used before, or set up a new name and password, etc.

  • My itunes library has organically grown from more than one itunes account but all now on a separate computer.  If I upgrade to iTunes match will I have to pay for each account?

    My itunes library has organically grown from more than one itunes account (all paid for by me) but all now on a separate computer.  If I upgrade to iTunes match will I have to pay for each account or just once, for the computer?

    No.  Provided the computer that you use to upload / match your Songs is authorised to play all of the Songs all works well - once complete you can download Song files that will play on your libraries / other computers without each computer having to be authorised.

  • On some pages the text from more than one paragraph stack up on top of each other, like writing something then writing something else on top of it.

    On some pages the text from more than one paragraph stack up on top of each other, like writing something then writing something else over the top of it. Some pages will run text and pictures together, like a car rear-ending another or a train pile up. Other pages will cut an image or text short, i.e. it will display a portion of the top of the image or text but not the rest. This happens on Amazon for example, the section where it says "Customers who looked at this also looked at" will allow only a certain amount of the upper portion of the description immediately below the picture of the product but below that section everything is fine until I get to another section displaying more products and their descriptions and then it cuts the bottom portions off again. I've noticed this behavior mostly in the sections with product photos, the text sections seem okay. YouTube also displays this behavior. It's even doing it on this page right now. Below this box I can read "The more information you can provide the better chance your question will be answered " , but directly below that in the next sentence I can see the start of it with "Troublshootin" and the "Automatically Add" in a green field covering the "g". The next clear text is "A window will open in the top corner. Click Allow, and then click Install. If the automated way doesn't work, try these manual steps." I tried turning of pre-fetching, clearing history, cookies, and cache, scanning for malware with Avast and Windows Defender all to no avail. It began when I upgraded from dial up to DSL via AT&T Uverse. I have a Motorola NVG510 modem. The modem was replaced an hour ago along with new dedicated lines and DSL/Phone splitter from the box by an AT&T technician to make sure my incoming lines were up to par. He ran a connection test and verified everything is up to standards. IE does not display this behavior. I am running Firefox20.0.1 and all previous versions have acted the same way since I upgraded to DSL about 3 months ago.

    If you have increased the minimum font size then try the default setting "none" in case the current setting is causing problems.
    *Tools > Options > Content : Fonts & Colors > Advanced > Minimum Font Size (none)
    Make sure that you allow websites to choose their fonts.
    *Tools > Options > Content : Fonts & Colors > Advanced: [X] "Allow pages to choose their own fonts, instead of my selections above"
    It is better not to increase the minimum font size, but use an extension to set the default page zoom to prevent issues with text not being displayed properly.
    You can use an extension to set a default font size and page zoom on web pages.
    *Default FullZoom Level: https://addons.mozilla.org/firefox/addon/default-fullzoom-level/
    *NoSquint: https://addons.mozilla.org/firefox/addon/nosquint/

  • Can I back up more than one mac to the time machine:

    Can I back up more than one Mac to a time machine? I have a laptop and a Mac Desktop computer can I back up both on the same Time machine

    Absolutely.
    However, quoting from ASC contributor Pondini's excellent Time Machine FAQ:
    It is advisable, though, to partition an external disk that will be connected to your Macs into one volume for each Mac ...

  • How can you set up more than one device on iTunes. I have an iPad, iPod, itouch and iPhone. I don't want the same on all devices.

    How can you set up more than one device on iTunes? I have an iPad, iPod, itouch and iPhone. I don't want the same on all devices. I have all my music/videos on iTunes on my mac book pro. Can you set up separate folders for each device and drop in what ever music/videos from the main iTunes library?

    In itunes it is called syncing and you can choose exactly what content to sync to all devices and it can be different for all of them
    How to sync

  • Reporting from more than one infocube and also from multiple ODS

    Hi all,
            Someone please help me in these issues.
    How can we do reporting from more than one cube ( if data in all the cubes are required, but only a few fields from each cube). And how to do the same with more than one ODS.
    Thanks in advance,
    Sekhar

    Hi Sekahr
    Can u jus create a multiprovider.
    Before creating the multiprovider..Just check the Common charcterstics avilable in
    all the ods based on that give the mapping ..
    and then once u have completd the creation of multiprovider execute the same in
    the tcode <b>Listcube</b> and then create the querys as per the user thats it...
    Regards
    R M K
    Assining points is the only way of saying thanx in SDN ***

  • JDBC-XI-FILE scenario. How to extract data from more than one table in JDBC

    Hi,
    I was asked a question like in JDBC-XI-FILE scenario........ How to extract data from more than one tables (i.e from JDBC system) ?? What is the logic to do the same ??
    I am not sure whether this is a valid question..........but any help in this regards is highly appreciated.
    Regards
    Kumar

    HI,
    Yes it can be possible ,please see the following links
    JDBC  Receiver with Oracle Stored Procedures
    configuring jdbc adapter with multiple tables
    RFC -> XI -> JDBC Scenario Updating Multiple Tables
    /people/alessandro.berta/blog/2005/10/04/save-time-with-generalized-jdbc-datatypes
    JDBC Adapter multiple Selects
    https://www.sdn.sap.com/irj/sdn/advancedsearch?query=jdbc%20with%20multiple%20tables&cat=sdn_all
    Regards
    Chilla..

Maybe you are looking for