Can't use Airport Express after upgrading to Leopard

I use Airport Express for wireless printing and AirTunes via powered speakers/hifi. It was working very reliably until I upgraded to Leopard. Now, I am unable to use Airport Express. I get the blinking orange light, but when I scan with Airport Utility, Airport Express is not detected. Manual setup is grayed out, so I can't set it up at all. I am using Airport Utility Version 5.2.2 (522.3), and there does not seem to be any updates or patches to apply at the moment. I have tried on my iMac G5 and MacBook, with the same result on both computers.
I am also reading that many others are having problems with Airport Express after upgrading to Leopard, perhaps not with my specific hardware configuration, but this is very disappointing.
I am open to suggestions to try a few things to get it working, so any help is appreciated.
Message was edited by: a j

From the Mail menu, select "Preferences". Hit the Accounts tab. Select the Account. Under Account Information, reapply the user name and password.
Check with the provider if the account needs authentication. This is in the Advanced tab. Usually just a repeat of user name and password.

Similar Messages

I currently have a D-Link DI-604 broadband router with windows computers. How can I add wifi to the network for use with ipad? Can I use AirPort Express?

I currently have a D-Link DI-604 broadband router with windows computers. How can I add wifi to the network for use with ipad? Can I use AirPort Express?

Yes. You can directly connect an 802.11n AirPort Express Base Station (AXn) using an Ethernet cable. The AXn would then just need to be configured as a bridge to allow the D-Link to continue to provide both NAT & DHCP services for all network clients connected to either router.
In this configuration, the AXn would broadcast a wireless network for your wireless network clients to connect to.

HT1515 How can I use Airport Express (1st generation) with OS X Mavricks?

How can I use Airport Express (1st Generation) with OS X Mavericks?

1st Generation AirPort Express will work fine with Mavericks.
Are you sure that you have a 1st Gen Express?
Check the model number on the side of the Express. 1st Gen is A1264.
If you see A1084 or A1088, these are much older versions of the Express that were sold long before Apple began to use the Generation naming with "n" wireless devices in 2007.
Mavericks will not support the A1084 or A1088. Use another Mac running Leopard, Snow Leopard, or a PC if you need to administer the older Express.

How can I use AirPort Express when traveling?

How can I use AirPort Express when traveling?

How can I use AirPort Express when traveling?
Connect the AirPort Express to the Ethernet port in your room.....to be able to create your own private wireless network in your room for multiple devices.
You will still have to pay the hotel Internet charge for one device, if the hotel charges for Internet access.
If the hotel only provides wireless service, then a single AirPort Express will not help you.
However, if you have two AirPort Express devices, then you can use one to "join" the hotel wireless network, then connect the second Express to the first using an Ethernet cable and create your own wireless network for multiple devices in your room.

Can I use AirPort Express as booster/extender to LinkSys router signal?

I have LinkSys N router (which I got free, else would've bought AirPort), its signal isn't strong enough in office room. Can I use AirPort Express as a booster/extender? Some sources say Express can only talk to another Express, others say it can communicate with the LinkSys. Which is it? I don't want to spend the money for two Expresses unless I have no choice (very limited budget nowadays).
I've been hassling with this for over a month, and I'm extremely frustrated.
Thanks to anybody who can help me with this.

Most likely no. That is because most non-Apple router's implementation of WDS is not compatible ... and this is true the other way around. It is true that some early Linksys models, mainly the WRT-54 series were compatible, but I have not seen anything since then that is.

Airport Utility can't find Airport Express after setting up as repeater station

I wanted to extend my 2Wire-based wireless network into a specific room that never seems to be able to pick up the signal, and found the following instructions on how to do so on Apple's website:
(note: these instructions were submitted by another user in response to a question as to whether or not an Airport Express could be used as a repeater station for non-Airport Extreme-based wireless networks - linked here http://store.apple.com/us/question/answers/product/MB321LL/A?pqid=QY4CAJJC7KFTTD KYH72DKPXF4CAUA9D4J).
Yes, you can do this two ways: If you can connect your airport express to your router via ethernet, then you will perform the following steps in the airport utility:
1. Select your airport express.
2. Select manual set up.
3. Under Wireless, select Participate in a WDS network
4. Enter your network name, radio mode, channel, and security
5. Under WDS, select WDS main
6. Check wireless clients
7. Add the MAC address of the router
8. Click update
That's it
Now, if you connect your airport express to your router wirelessly, all the steps are the same except for step 5. In this step, select WDS remote instead. Everything else is the same.
I followed those instructions exactly with my Airport Express and, after restarting, the amber light is flashing on and off continuously and the Airport Utility can't find the Airport Extreme base station. What the heck went wrong here?

Update:
I restarted the laptop I used to set up the AX as well as pushing the "reset" button on the AX (first time - pressed it for 1 second, Second Time - pressed and held for 15 seconds then let go). The Utility still isn't recognizing the base station.
I also upgraded the Utility's software to 5.5.3 right before I went through these steps, and now it's not recognizing the base station. ARGH.
Update #2: I plugged the AX into my laptop with an ethernet cable and the utility STILL can't detect it. This is ridiculous.
Update #3: Not 30 seconds after update #2, it FOUND the **** AX >.< I'm updating the firmware, but I still can't get it to work as a repeater station if I have to plug it into my laptop all the time JUST to get the Utility to recognize that yes, Virginia, there IS an Airport Extreme.
Message was edited by: bleedingrose19

Can I use airport express to extend my network AND stream iTunes???

I have an airport extreme connected to the cable modem and sending a signal out to my home network. I also have a powerbook and an airport express connected to the home stereo.
My question is, can i use the express to extend my extreme signal (to reach the back yard) and stream music from itunes at the same time? The set up utility seems to suggest that you do one or the other.
Thanks!

Are you sure you configured the Express to extend the Extreme's network? If you use the standard setup, the two base stations will be indistinguishable, i.e. you'll only see one entry for the wireless network.
If you were connected to the Extreme when you configured the Express, try turning off Airport in the Airport menu and then turning it back on. The computer should pick up the stronger signal at that point.

Can I use airport express to create a local wireless network that my apple tv can connect to for AirPlay/mirroring in student halls/dorm without Internet connection

Hi I was wondering :
Would I be able to make a local wireless network using airport express that my apple tv can connect to which in turn is connected to a projector with hdmi in so that I can mirror/AirPlay from iPhone pad and mac

will the Airport Express allow you to log onto a hotel wireless network, and broadcast a secure wireless network in your room for your wireless devices, like the Ipad, Iphone, etc.?
The bottom line with a single AirPort Express is no.
The AirPort Express can only "extend" a wireless network when the network is being provided by another Apple router.
As you might imagine, it is extremely unlikely that that the hotel network....which no doubt uses professional wireless access points provided by a manufacturer of commercial systems.....would be compatible with an AirPort Express.
In many years of travel domestically and internationally, I cannot recall a time when a single AirPort Express would "extend" the signal provided by a hotel's wireless network.
However, if you had two AirPort Express devices handy, you might be able to configure one to "join" the hotel network and provide an Ethernet signal to the second AirPort Express, which would be configured to "create" your own "private" wireless network.

Can I use Airport Express with iPhone in my hotel room?

Is there a way to set up an Airport Express in my hotel room when I travel, so that the provided High Speed internet cable in the room can be plugged into my Airport Express, giving me a wireless internet connection for the iPhone? I use Airport Express often this way with my MacBook, so I don't have to be tethered to the cable.

I did this about a month ago when I was in England. I just had the Airport Express with me, and had not done any configurations. I plugged it in and had the iPhone find it. It worked in some hotels, and didn't at others. When it worked it was great. I assume with some of the hotels where it didn't work, that I needed to configure it but since I didn't have my laptop I didn't have any way to configure it. Is there any kind of "universal" or "automatic" configuration you can set it up with?

Can I use airport express in a wired network to play music through my stereo?

I originally used my 1st gen AE to wirelessly stream music from iTunes on my MacPro to my home theater. This works, but there are some good days and some bad days where there are dropouts in the music. I have recently run Cat6 cable to my HT from my router next to my MacPro. This feeds a Gigabit switch that feeds the ATV, receiver, bluray, HD DVD, etc. I plugged in the AE to the switch but it still defaults to the wifi network rather than taking a feed from the ethernet switch. I know i can (and do) use the ATV (gen 1) to steam music, but sometimes it more convenient to use the AE. Is there a way to force the wifi on the AE off and just have it for streaming from iTunes? Thanks.

Yes, you can configure an AirPort Express Base Station (AX) as a standalone wireless router without Internet access for the purposes of providing a Wi-Fi network for streaming. Note that any computers that will be the host of that stream would need to connect to this AX's wireless network while doing so. They would not be able to be connected to two wireless networks simultaneously for both streaming AND Internet access.

I have a MacPro 2008 workstation without Airport or Airport Extreme CArd isntalled. Can I use Airport Express to connect (wireless) to my wireless network? If so, can I then connect my Airport Extreme to my MAcPro by a ethernetcable ?

I have a MacPro 2008 workstation. It has no Airport/Airport card so I have to use an ethernetcable to connect to my modem. As the MAcpro
is in my office in the attic and the wireless modem is in the basement I have a problem. I wonder if it is possible to use Airport Express to connect to the wireless network? Itshould be like this: in my office I connect the MacPro with AE through an ethernet cable. If I can then get AE to connect (wireless...) to my wireless network I should be ablle to connect my MacPro to internet/wireless network. Is this possible???? Any suggestions are very much appriciated. Thank you.

Apple calls this configuration a ProxySTA.
To activate ProxySTA, you must set up the Express to join a wireless network and then enable the Allow Ethernet Clients setting; both settings are located in the Wireless tab of AirPort Utility.

Can I use airport express with my osx 10.3.9

I have osx 10.3.9 and would like to upgrade to to lion maybe and use airport express if possible .....what do I need to do?
Oneday26

So we know more about it...
At the Apple Icon at top left>About this Mac, report the version of OSX from that window, then click on More Info, then click on Hardware> and report this upto but not including the Serial#...
Hardware Overview:
Model Name: eMac
Model Identifier: PowerMac6,4
Processor Name: PowerPC G4 (1.2)
Processor Speed: 1.42 GHz
Number Of CPUs: 1
L2 Cache (per CPU): 512 KB
Memory: 2 GB
Bus Speed: 167 MHz
Boot ROM Version: 4.9.2f1

Can't configure Airport Express after firmware upgrade 6.2.

I have an Airport Extreme (V5.6) and I recently upgraded my Aiport Express to firmware 6.2. I was using the Express to extend my range and attach to my stereo for iTunes. I went out of town and took the Airport Express with me to use in my hotel rooms. Everything was fine. When I returned and I re-attached the Airport Express to the system at home, it said there was a firmware upgrade, so I went ahead and did the upgrade. Since that time, iTunes has not been able to recognize the Express. It tries, but cannot find it. I then tried to reconfigure the Aiport Express but i get an error message "An error occurred while attempting to communicate with the AirPort Express. (-8)". Does anybody have a solution. I'm afraid to update the Base Station firmware for fear that I might run into the same problem. I'm running an aluminum Powerbook G4(1.25 ghz).

Hi,
I don't really know the solution, but the Airport Express firmware is now at 6.3. Maybe you should use this latest one to see what's happen...

Itunes skips on airport express after upgrade

I have been using Itunes wirelessly with airport express for years, not a single issue. Then I upgraded to Itunes 9.0.2 and at the same time I installed ther latest security update (I think 2009 006). Both updates were installed simultaneously.
But from that moment on I lost the ability to use Itunes through Airport Express. It just skips every three or four seconds, stops, restarts, it's like going back to a vynil record with a deep scratch.
Works fine with internal loudpseakers and with the jack out. It's just airport express wirelessly that doesn't work.
Airport express firmware is 6.3, It is only connected to my hifi system. That is its only function. It is set as "join an existing network" and the existing network is fine. Airport utility reads it as functioning normally, and the light is green.
What can the change be? Should I go back to Itunes 9.0.0?
Thanks for your help
antonio

Hi,
Ive had an Airport Express since i bought my copy of Leopard, it worked brilliantly for ages, but then skipping started. Yes im on the 6.3 firmware and yes im using Snow Leopard with iTunes 9.0.2. But ive been having this problem for ages. Loads of people are recommending getting a copy of AirFoil (which pays for itself to be able to listen to Last.fm) and even turning off IPv6 but now, after a couple of days using it.. back to normal.. skipping every couple of minutes for about 10 seconds..
I cant help but think that theres a finite life for these AE devices, im sure Apple know about it (ive already put bug reports in via the normal channels) but its quite a bit of £ to spend on another one just to get the same result..
Its a brillant product, but i think after very sparse use for a couple of years doesnt really mean you need to buy a new one.

How can I use Airport Express to create a standalone Wi-Fi network without Internet Access so I can browse web pages on the local network? I will be using MAMP as my server (Apache)

I would like to create my own Wi-Fi standalone network at an upcoming tradeshow where there will be NO internet access.
Currently, I run and develop sites on my iMac use MAMP to manage my sites locally. Using MAMP, I run my sites as though they are on the internet although everything is local.
I purchased an Airport Express hoping I could create a standalone network so that the iMac would broadcast its website to whatever device connects to it such as my iPhone, iPad and MacBookPro.
However, after setting up the network successfully (I have a green light on the Airport Express, and there is NO internet going through it), I am not able to go any further by logging into the iMac's websites from the other machines. Form my MacBookPro Finder, I can look at files and folders using afp://10.0.1.2, from the Find/Go/Connect to Server utility, but I can't browse the website that is running on the iMac via the Safari browser.
Can anyone help me configure my MacBookPro (or iPad, or iPhone) to run the website on the iMac when they are all on the same network?
Thanks so much!!

1) connecting the TC using a ethernet cable from one of the two modem's LAN ports to the TC's WAN port
2) create a new Wi-Fi network using the TC ?
Does someone already create a new Wi-Fi network using its TC connected by Ethernet on a modem/router device ? How do you set up the DHCP (and NAT) ? Which range did you use ?
This is easy enough to do..
Plug the TC directly into a computer.. without other connections to do the setup.
Using the newly installed 5.6 utility.
Bridge the TC.
Create a wireless network.
This is an older screen shot and I would set security to WPA2 Personal only not WPA/WPA2 Personal as shown above.
I do recommend you use wireless names that are short, no spaces, pure alphanumeric.
Update the TC..
Now plug it into the modem router.. it will be a part of the network without doing NAT and DHCP itself.. which you do not want.. that leads to double NAT issues.. but it is a WAP that provides access to devices on both 2.4ghz and 5ghz bands directly to the main router.

Can't use Airport Express after upgrading to Leopard

Similar Messages

Maybe you are looking for