Can the DAQPad 6052E be powered by 12V?

I am setting up a field audio DAQ. I am interested in using the DAQPad 6052E with a laptop on a boat. Is it possible to run the DAQPad off a 12 volt deep cycle battery?
If not would alternatively using a 120 VAC inverter cause a lot of noise to leak in? Any help would be greatly appreciated.

Hello anu25,
The specifications of the DAQPad-6052E manual state that it can take 9-24 VDC and requires 20 Watts of power (see page 14 of the specifications manual linked below).
NI 6052E Family Specifications
http://digital.ni.com/manuals.nsf/websearch/EAA4406C446E621B86256DA20074054C?OpenDocument&node=10931_US
So, if the 12 V battery can supply enough power, it should work for you.
There is a battery pack and 120 VAC charger option for the DAQPad-6052E that would be an alternative as well.
NI DAQPad-6052E for FireWire
http://sine.ni.com/apps/we/nioc.vp?cid=10931〈=US
I hope this helps. Let me know if you have any additional questions.
Regards,
Todd D.
NI Applications Engineer

Similar Messages

  • Can the DAQPAD-6016 generate a pulse train?

    If so, what is the procedure and what pins are involved? Also, where can I find a 6016 Users Manual showing a pinout description?

    Avana,
    Greetings!
    You can find a pinout for the 6016 from this manual:
    http://sine.ni.com/apps/we/nioc.vp?pc=res&cid=14041〈=US&p_0=manual
    AND
    Yes, you can setup a pulse train. You would use the counters. If you are using LabVIEW you can go to Help >> Find Examples to help you set this up.
    Hope this helps,
    AnujD

  • Can the iPod firewire power adapter(LR56612 A1003, using 12V pin

    Can the iPod firewire power adapter, part# LR56612 A1003, using 12V @ 1amp on evil connector pin#19.20 to charge iPad2?   I am trying to save a few bucks and make my 31+ years of Apple life easier.   Thanks a bunch.

    No

  • Can the NI 9208 AI card except loop powered and single 4 to 20 mA signals.

    I have an application that I am using a NI 9208 current input card.  The signals that are connected are both looped and single input.  The looped powered sensor is connected to AI0, COMM and Vsup.  I have a 24 Vdc power supply connected to Vsup and COMM.  The other sensors are not 4 to 20 mA looped powered and they are connected to COMM and AI1...AI4.  All the sensors share the same 24 Vdc power source.
    Can the NI 9208 except both types of connections?

    Hi ChadAnd,
    The 9208 can accept loop-powered and three-wire current transducers. Refer to pages 9-11 of the 9208 Specifications Manual for more information. As far as your AI1-AI4 sensors, as long as they fall within the input range (typical 22mA), you should be fine.
    Hope this helps!
    Xavier
    Applications Engineering Specialist
    National Instruments

  • Can the Iphone locator pinpoint in my house where iPhone 5 is when it is powered down?

    Can the Iphone locator pinpoint in my house where iPhone 5 is when it is powered down?

    Thanks! Can google maps show exactly where I lost it instead of just showing  my house.?
    Getting desperate here.

  • HT1414 i think my iphone 4s has a damaged software because it locks the phone always and powers it off without touching the power button. how can i rectify this problem?? i already tried erasing all the settings and content of the phone. thanks..!

    i think my iphone 4s has a damaged software because it locks the phone always and powers it off without touching the power button. how can i rectify this problem?? i already tried erasing all the settings and content of the phone. thanks..!

    This is a user to user help forum only. You are not addressing Apple here.
    My iPhone 4S, iPhone 5, and iPad 2 are running 6.1.3 with no such problem and the same with the overwhelming majority of iOS devices running 6.1.3.

  • Can the adobe footer be removed, where it says powered by adobe, terms of use, report abuse?

    can the highlighted footer be removed or hide it?

    Hi luigi554,
    Unfortunately, it is not possible to remove the footer from the fill able forms created using Adobe FormsCentral.

  • Questions about the DAQPad-6020(BNC)!

    I am a newer in NI DAQPad-6020E(BNC) and also unfamiliar with such hardware device.We know that the board has 16/8 I/O from ACH0 to ACH15. In the deviec user manual, it has mentioned three different input modes—nonreferenced single-ended(NRSE) input, referenced single-ended (RSE) input, and
    differential (DIFF) input. But now what confuses me is that where are the inputs ACH8 to ACH15 and how to connect a out equipment to a couple inputs such as the couple ACH0 and ACH8 in DIFF input mode. Are they just connected together to the ACH0 instead to ACH0 and ACH8 espectively? Or how to connect external sensors to any input from ACH8 to ACH15 when in single-ended input mode.
    Another question is the sensor volatage parameter sel
    ection according to the DAQ protection voltage. Referring to the device user manual, the protection voltage is Vcc+0.5. Then, what does the constant Vcc point to? Where can I find the specified value of the Vcc since the sensor I/O voltage is direct relative to the board protection value. Thus, what the value is? Is it the same in all E-series DAQPad? Or is it referred to somewhere different from different device.
    I am urged for your help since the project is coming.
    Very thankful for your hearted help.

    Hi Sammi,
    The DAQPad-6020E (BNC) is designed for convenient measurement of up to eight differential channels using BNC connectors and cabling. In certain situations, however, it may be desirable to increase the channel count beyond eight. In this case, you must use one of the single-ended measurement modes (RSE or NRSE) with the DAQPad-6020E (BNC). Up to 16 (ch0 to ch15) single-ended channels are available in the single-ended measurement configuration.
    Single-ended measurement modes require changing the source type switch (S0 through S7) settings. Figure C-1 in the User Manual shows the ground-referenced resistor switch settings.
    Actually the BNC connectors on the front are connected to differential channel pairs, so the BNC called ACH0 is actually
    connected to ACH0 and ACH8. Therefore, if you want to do single-ended measurements, each BNC connector is giving access to the "+" terminal of two channels (ACHx and ACHx+8). Depending on your choice of referencing, the ground point of the signal should be connected to the AISENSE (for NRSE) or AIGND (for RSE) pin.
    There are different overvoltage protection specifications depending on the input type. The analog inputs (AI) are protected up to +/-35V when powered on (+/-25V when off). The Vcc value you is referring to the digital 5V, but the analog inputs are not referring to this value.
    Hope this gets you started.
    Philip C.
    Applications Engineer
    National Instruments
    - Philip Courtois, Thinkbot Solutions

  • Can the AirPort Extreme support more than one printer at a time?

    can the AirPort Extreme support more than one USB printer at a time if it is connected to a USB Hub?

    can the AirPort Extreme support more than one USB printer at a time if it is connected to a USB Hub?
    Yes.....IF.....you use a powered USB hub.
    I have had 3 printers connected at the same time in the past and assume that more would work as long you have a powered hub to support the number of ports that you need.

  • Can the Plug-in Compete?

    Why hasn't Java become the dominant technology in RIA development?
    I'm not the first person to ask this question, nor will I be the last. It is unbelievable to me that the company that invented the RIA over a decade ago has made little or no progress in this field and presents absolutely no challenge to inferior technologies that came later. JavaScript was named "Java" script deceptively to give it better visibility in the marketplace, but given its dominance in the RIA market, you'd never believe it.
    I have been developing software for over 25 years now with the majority of my experience in C++ development and object-oriented analysis and design. Wanting to move into the web market, I started doing RIA development a few years ago. I was horrified by the development options available to me and the seemingly infinite amount of hoops I had to jump through to get even the simplest application functionality implemented and working correctly. I had been using Java to do backend work and had really come to like it. To me, the ideal situation would be to use Java to do the client-side work as well as the server-side work. Not only would I be using a real OO programming language, I'd also be using a single technology across the board. The problem was that there really was no nice client-side Java solution available. Swing was just too cumbersome and inflexible and other products had similar drawbacks. What I really wanted was a client-side solution that was as easy to use and just as flexible as HTML/CSS for building a UI, but provided the dynamic and robust programming features of Java. So I quit my full-time job about 18 months ago and started designing a Java-based RIA product called the Galileo RIA Framework.
    One of the many frustrations that I had experienced working with JavaScript was the problem of inconsistent appearance and behavior on different browsers; therefore, when I started designing Galileo one of its primary requirements was that it be able to run on all major browsers on all major platforms and produce a consistent looking UI. Knowing the history of the Java Plug-in, I wasn't sure if it would meet this requirement. Much to my relief, it turned out that the latest Java plug-in (1.5 at the time) worked fine with all the latest and greatest browsers (IE, Firefox, Netscape, Opera, Safari, and Camino) on all of my test machines which included Windows XP and Vista, Mac OS-X, and a few Linux distros. This was great. I figured now all I had to do was focus on developing the actual UI framework and I would have the product I had been longing for and a product that the Java community would be excited about.
    I recently released Galileo as a Beta and while many developers who have looked at the product have admitted that it is an impressive product and that they'd like it to gain much success, they are reluctant to use it because it depends on the Java Plug-in. This has been a major disappointment to say the least. I knew that applets had developed a stigma over the years, but I didn't realize how pronounced the distaste for the plug-in had become. The negativity and skepticism within the Java community itself is so overwhelming that any hope for wide acceptance of the plug-in seems impossible. The funny thing is that all the developers I have talked with would like the plug-in to become widely accepted, but in order for it to become widely accepted, it would have to be used, however, most website developers are hesitant to use it, because, well, it's not widely accepted.
    I want to change this. Not only because the success of my product depends on it, but because I would like more job opportunities to be available to me as a Java programmer as the RIA market continues to grow.
    Why did the Java Plug-in fail in the first place?
    My guess is that there were several major reasons for the failure of the Java Plug-in. One, applets and the plug-in were introduced at a time when most users were limited to dial-up access to the internet. Downloading the plug-in and the applets that used it took too long for a normal user's patience. Two, a Swing UI compared to an HTML website designed by a graphics artist looked terrible. Three, platform and browser compatibility may have been an issue also, but not being involved in Java development back then, I don't know if that was an issue or not. Four, it has been said that installation of the Plug-in was not straightforward and could have been difficult for non-developers. Five, the web was still pretty new itself. The concept of the RIA didn't exist; therefore, there wasn't any pressure for websites to be anymore than straight HTML. Adding technology that complicated implementation, limited potential visitors, and looked bad, just didn't make any sense.
    Can the Java Plug-in compete now?
    I'm optimistic it can for several reasons. One, according to the latest statistics I've read, 86% of U.S. internet users now use broadband. Download times for JAR files and other resources have become negligible. Two, Sun has finally decided to rewrite the plug-in making it easier to detect, download, install, and upgrade. Also most major browsers will prompt the user in a standard way to install the plug-in if a page that requires it is loaded. Three, new operating systems / machines are coming with the Java plug-in already installed. I know both my Windows Vista machines from Dell did, my Mini-Mac from Apple did, and several distros of Linux install the plug-in when the OS is installed. Four, installing a plug-in just isn't a big deal for users anymore. According to a June 2008 survey 99% of internet enabled desktops have already installed the Flash plug-in and 85% have Java installed. Five, standard HTML websites are no longer the standard. To be competitive, websites will have to continue to evolve with RIAs being the latest evolutionary step. Where standard HTML sites with bits and pieces of JavaScript could be developed by graphic artists and other non-developer types, RIAs, because of the complicated implementations, require software developers. Where the major driving force in the web development market used to be graphics artists and non-developer types, as the RIA market grows software developers, many of which are Java developers, will become a greater driving force. This opens up more opportunities for Java. And six, with a framework like Galileo which allows easily customizable UI's that can look as good as any HTML/CSS based UI, aesthetics are no longer an issue for Java UI's.
    I was discussing this issue with Marty Hall of www.coreservlets.com this week and here's what he had to say:
    I would love it if a Java-based solution gained some traction in the RIA world. I spend a lot of time doing Ajax training, and right now, Ajax is tremendously complicated for developers. Developers have to learn xhtml, XML, JSON, JavaScript, Prototype, 37 other JavaScript libraries, and a server-side technology (servlets/JSP, PHP, ROR, or whatever). Even with integrated technologies like GWT or JSON-RPC, there are still an awfully lot of underlying technologies for a developer to master, and the interface is still limited by what current browsers can support."
    I really hope your framework catches on. It would be a good thing. You could build apps that were so much better if you had a real programming language and a single underlying technology.
    The more compelling apps out there that get people to install Java in their browsers the better. And the more powerful but simplified GUI frameworks like yours, the better.
    JavaRiaDev.org
    I believe a window of opportunity has opened to give the Java Plug-in a rare second chance. It appears that Sun believes this too, since they have taken the initiative to redesign the plug-in and to create JavaFx. However, with no disrespect to Sun, if Java developers expect the plug-in to succeed due to Sun's efforts alone, I think they are sadly mistaken. In order for the plug-in to succeed, a concerted effort by the Java community will be necessary. For this reason I have created JavaRiaDev.org. The main initiative of this effort will be to pool developer resources to create RIAs that utilize the Java plug-in and appeal to a broad audience by coming up with new ideas for websites, copying successful website ideas and making them better, and/or trying to forge strategic partnerships with existing websites that already have a substantial user base who are looking to upgrade to RIA technology. The second initiative will be to provide the appropriate resources to help other developers interested in Java RIA development. I, of course, will be pushing Galileo, but will welcome the use of any product that promotes the use of the Java plug-in.
    There will no doubt be skeptics in the Java community who say this is a fool's errand. But for those like me who are not content sitting on the sidelines waiting for others to decide their fate, I say join me and help me in my effort to make Java, if not the dominating, at least a viable option for RIA development. Personally I'd like to have an impact that creates the general opinion that any machine connected to the internet that isn't equipped with the Java plug-in is an inconvenience to the user. If a machine has a modern browser there's no reason for it not to have the plug-in.
    If you are interested in becoming a part of this effort, please email me.
    Thanks,
    M. Warble
    [email protected]

    Some people on the forum claim that you can use an iPhone charger with an iPad, but it will charge slowly enough to the point where the iPad won't show charging status.
    You can use the iPhone with either charger, but that doesn't hold true for the iPad, like Kappy says.

  • My Mac Mini was not sending a signal to the monitor. I powered down using the power button and now it will not start. When i power up I get a strange 2 tone sound, like a warning alarm. The fan starts, and the light comes on, but no screen

    My Mac Mini was not sending a signal to the monitor. I powered down using the power button and now it will not start. When i power up I get a strange 2 tone sound, like a warning alarm. The fan starts, and the light comes on, but no screen.
    I have tried with a wired USB keyboard and mouse using a single screen. Powered up with option pressed. No change.
    Reset SMC  no change

    Run the Apple hardware test to see what it tells you. Run the extended test when prompted, which can take awhile.

  • Can the last link in a thunderbolt daisy-chain be a non-thunderbolt monitor using miniDisplay port?

    Can the last link in a thunderbolt daisy-chain be a non-thunderbolt monitor, using miniDisplay port?
    For example, Mac mini <--> external SSD <--> apple cinema display 30" (using miniDisplay port adaptor plugged into the SSD's second thunderbolt port)

    TechnoMax wrote:
    for instance STAE122 or STAE 127?
    FWIW, STAE129 is the current version TB adapter
    that is self powered and has TB daisy chain port.
    STAE122 and STAE127 are older versions and
    not the current model, though there may be stock of
    these around.  As to whether this will solve your issue,
    I don't know.
    Can I trick the Mac under Bootcamp as OS to use HDMI for the monitor? Dell officially says that the monitor can only accept 1900x1080 over HDMI, but some have fiddled wth different computers with custom settings that worked with some Monitors but mostly under Linux and to Dell 2711.
    The MacMini HDMI port is hardware limited to 1980x1200.

  • Can the Apple Universal dock

    Can the Apple Universal dock &amp; remote work with the iPod nano 7th generation?  Especially to connect to a powered speaker in my home stereo system? 
    Will the new Lightning to 30 pin adapter be required &amp; will it work in the Universal dock?

    Will the new Lightning to 30 pin adapter be required &amp; will it work in the Universal dock?
    Not without the appropriate adapter.
    http://store.apple.com/us/product/MD823ZM/A/lightning-to-30-pin-adapter
    B-rock

  • Can the iMac G5 supports TWO USB 7-port Hubs??

    Hi all, call me greedy but belive it or not, I am running out of USB ports!!
    I have a Belkin 7-port USB 2.0 Powered Hub (with 2 ports pointing upbright) which serves me very well, but I am running out of ports, now that I am considering getting the new iPod nano.
    Anyway, there are 3 ports behind the screen, now I have my Mighty Mouse, the Hub's USB cable and a HK Soundsticks attached.
    I am thinking of getting another similar 7-port Hub, they are actually stackable, but of course I won't use all 7 ports fully on the 2nd new one.
    Can the iMac supports and substain 2 USB hubs?? I have actually never seen anyone with more than 1 hub??
    Thanks and cheers

    I have two USB hubs attached to my iMac G5 - they are both self-powered (their own power supply); one is a USB 2 with 6 ports and a multi card reader built in and the other my old USB 1 with 4 ports. They are plugged into the rear of my iMac along with the printer. Everything else, including keyboard and mouse, are plugged into the hubs and I am using a total of 8 ports - and everything works. I don't know if that would change if they weren't self powered.
    Hope this helps.

  • What's the largest capacity bus-powered external hard drive?

    I realize that this isn't a Mac specific question, but I'd really like a recommendation. What's the largest capacity bus-powered (preferably USB) external hard drive available. My new MBP has a 500GB drive so I would need something with probably 640GB or bigger. Problem is I can't find anything over 500GB that's bus-powered. Everything I've found requires an external power supply which is what I'm trying to avoid. If anyone has a recommendation, please share it.

    Have a search on the web for USA retailers who supply empty enclosures and drives separately. The enclosure is the physical case and the bits of circuitry and the physical ports. Tell them what you want and ask him what drives and enclosures he has to suit your purpose and if he can fit the two together for you. I have such a supplier but am in UK.
    Does it have to be a USB bus? Firewire is better and gives more power. One way I power a 360GB pocket drive is to feed from TWO USB ports on the computer into one input port on the drive(now in the enclosure) you should be able to buy a sort of "Y" shaped cable with two full size flat USB connectors at one end and one single connector at the drive end. The drive end often will be a mini usb port. What you want will depend upon the size of the input into the drive.

Maybe you are looking for