Can the route consider the transportation calendar in APO?
Hi GATP experts,
the transportation calendar is normally part of the transportation lane.
Is it also possible to assign the transportation calendar to the route?
Thanks for help.
No it is not possible.
Development is necessary.
Similar Messages
-
Why does the router consider the VoiceEncapPeer an interface
I have MC3810 and 26xx routers running VOFR and VOIP. My network management stations sees the VoiceEncapPeer and VoiceIPPeer go down and then back up. Are these actual interfaces and what is causing the peer to flap.
If this is what you management station says, then the
only option is someone did a shutdown , no shutdown on the
dial-peer for vofr and voip.
Interface up/down does not affect the admin or operational state
of voice dial-peers. -
Why do the connected devices to the router have the smae IPV6 address?
Hi,
Now I meet the issue
The operation steps on router (WRVS4400N):
1.Set the IP mode as Dual-stack IP and then save
2.Disable the IPV4 DHCP server
3.Use other deivces to connect the router.
The connected devices have the same IP address(2005:123:456:789::1),I am confused,why is it?
please help.
Thanks!Hello,
The WRVS4400N is in fact assigning IPv6 addresses to all the devices connected to it, but the WRVS4400N does not show a table with the IPv6 addresses assigned to each device connected, it only shows the IPv4 addresses and the respective MAC address for each device. The IPv6 of the WRVS4400N is an aggregetable global unicast IPv6 address (See the image below)
If you go to Setup > LAN you will see that you cannot modify the prefix of the IPv6 address, all you can modify is the postifx and prefix length field (As you can see in the image below).
For more information about these fields and general IPv6 configuration, please refer to the article IPv6 Configuration on WRVS4400N Wireless-N Gigabit Security Routers
The only way you have to see the IPv6 address assigned to each device connected to the WRVS4400N is to check on each device the IPv6 address assigned. The WRVS4400N does not provide this information. You can see from the below picture the IPv6 address assigned to my computer. As you can see, the WRVS4400N assign the the computer the prefix 2002:c0a8::/6. Then you can see the actual IPv6 address which is 2002:c0a8:0:b182:e6a:9b0e:cdcf.
As you can see, the initial part (The prefix) remains the same, since these are the first 64 bits of the whole IPv6 address. The other 64 bits of the IPv6 address represents the interface ID, that is, the device that is connected to the WRVS4400N.
I hope you find this information helpful. If you have further questions, don't hesitate to ask.
Alejandro Moncada
SBCD Engineer
[email protected] -
How to call a previous operation in the routing in the backend?
(We have a requirement to call a previous operation in the routing in the backend and create-assemble-complete the SFC.)
Routing would be u2013 OPERATION_1 -> OPERATION_2 -> OPERATION_3
The SFC has not been create and we are using u201CCreate SFC On Demandu201D.
The production operator is given the SFC value to use, however, the POD is configured to START the SFC at OPERATION_2
The desire is to process the SFC at OPERATION_1 as a u201Cblindu201D operation to production.
The question: If we use a PRE_START activity, is it possible to launch the PRE_START activity at OPERATION_2 and have the activity:
1) Create the SFC,
2) Start the SFC at OPERATION_1,
3) Assemble a child SFC (part of the activity information),
4) Complete the SFC at OPERATION_1,
5) Upon completion of the SFC at OPERATION_1 finalize the activity and allow the SFC to start at OPERATION_2 normally?
Thanks and Regards,
Avinash
Edited by: Avinash Fernandes on Feb 16, 2012 3:30 AMHi,
a managed property only gives you a anlde to a bean or property, it doesn't execute it. To execute a bean, you can use a custom JSF PhaseListener that calls a bean method. The reference to the bean is achieve through value binding
ValueBinding vb = FacesContect.getCurrentInstance().getApplication().createValueBinding("Name of Managed Bean);
TypeOfBean theBean =(TypeOfBean) vb.getValue(FacesContext.getCurrentInstance());
.... theBean.theMethod() ...
Frank -
download connections doesn't close after I cancel the download, it keep like I am downloading and only close when I disable the network adapter or reset the router or the firewall.
I use pfsense as my firewall and see the traffic not reseting to zero when I cancel download.
Also, IE doesn't have this problem. When I cancel the download the traffic drops to zero.And this problem seems to be systemwide. Since I created a new user and under which problem still exists.
Hope apple will look into it -
My Wi-Fi just says connecting, but never connects. I've rebooted the router and the phone.
Well that was it. My Wi-Fi just says connecting but never connects. I've rebooted the router and the phone. LG G2
ETea,
Sorry to hear about the trouble with Wi-Fi. Let's get you connecting again. Are other Wi-Fi capable devices able to connect without issue? Go to Settings and touch Wi-Fi. Touch your network and select "Forget." Touch "Search" on the bottom. Once the phone detects the network again, touch the network, enter your password and select connect. Let us know if you get connected.
BrianP_VZW
Follow Us on Twitter @VZWSupport -
Im setting up a server with the port 25565 and im doing it with Port Map but the problwem is i cant seem to get it to work with my router. it goes through my macmini to the router and the expansion hardrive
Im setting up a server with the port 25565 and im doing it with Port Map but the problwem is i cant seem to get it to work with my router. it goes through my macmini to the router and the expansion hardrive
-
Doubt about changes in the routing for the next year
Hello All,
I have a question hope for you guys to gave a brief and technical answer to me.
I have some doubts, one doubts is in the actual routing, can I change the Valid to ( Date) in the routings in the operation. (Example. original valid to date is 31.12.9999 i want to change this with 31.12.2007). Because we want to create new routing with changes for the next year. But it´s necessary the new routing is valid from 01.01.2008 and valid to 31.12.2008.
And I can´t 2 routings with the same valid for 01.01.2008
I have many routings for change and I have other option like change the status (create or release).
Other doubt, the user has a excel file with the changes necessary, how can I upload from excel file to SAP R/3. It exist one program, one procedure u other option.
Your kind response is what am ex[ecting expert. Thanks,Hi
pl use the ECM functionality (engineering change functionality) for the same..its standard SAP and no need for any special config..
You can channge the same routings by giving the effectivity date in ECR (eng change request)
for creating an ECR pl follow the below steps
=Create Engineering change request - TCODE - CC31
=Click on object type after entering this screen parameters
=Click on status management
=and change status by clicking on Check request
=Select the required objects types to be changed and click on objects to reach the below screen
=Enter the required objects to be changed via selecting appropriate tab.
=Select the object and click on details
=Click on status management
=Go to Header and click on status
=Change the status by clicking upto convert request.
=Click on the save button and Engineering Change Request has been created..
IMP Notes -
Do close and Release the Engineering change request after doing the appropriate changes at both Object level and Header Level
Pl come back for any further clarifications..
rewards will be appriciated if found useful
BR
Sumit -
How to access to configuration page of the router through the windows phone 7 ?
Hi all
I'd like to know if there's a way to access to configuration page of the router through my windows phone 7.
I usually access the router by laptop as following: "192.168.1.1". but sometimes when I'm on my phone I need to reboot the router through my phone other then the laptop which is not near me...
I looked up for applications that should do the work, but unfortunately I got no positive result, so I'm reaching out to this very forum in order to find help and tricks so that I can figure it out
thank you in advanceHi Happydz,
For help using Windows Phone please post in the Windows Phone forums on
http://answers.microsoft.com .
The MSDN Windows Phone Development forums are for developers to discuss writing their own Windows Phone apps.
That said, I'd expect you could connect to 192.168.1.1 from the phone's browser the same way you would from the laptop's browser. -
IPad wifi receptions depends on the router, not the iPad!
Ok. I am surprised I haven't heard this from you smart people:
*The wifi problems are specific to certain types of routers!!!*
Example: My Pad works like a champ at work. The router there is an old Linksys G.
It works like crap at home. At home I have a newer Belkin N/G.
That's why some people have problems and some don't: It depends on the router.
So...My question is: What is the best router for an iPad?
I'm willing to go out an buy it; I just want someone to tell me the best one!!I have a Belkin router and it has been setup as WEP. Since having my iPad it has lost connection every time I start it up. I so
Spoke to support today and the fix is this:
You need to go into your router setting and go to security and change from WEP to WPA personal and set the past word as you already had it.
Sine I have done this the iPad has not lost connection once so this does work. If your router does not have WPA then see if you can do a firmware update.
Andyd -
AAA authentication when logging into the router via the web browser
Hi group,
I am trying to get access the a cisco 2621 via http and authentication
via AAA but there is something I am not quite understand.
I am using the freeware TACACS+ server running on RedHat Linux
Enterprise Server 3.0. I setup the TACACS+ account for myself with
enable privilege on the TACACS+ box. This account, let call it,
ddt123, can telnet/ssh into the IOS router and the enable secret
is associated with this account as setup in TACACS+.
Here is my configuration looks like on the TACACS+ file:
[root@dca2-LinuxES tacacs]# more tac_plus.cfg
accounting file = /var/log/tac_plus.log
key = zFgGkIooIsZ.Q
user = ddt123 {
member = admin
name = "ddt 123"
login = cleartext "exec123"
user = $ddt123$ {
member = admin
name = "ddt 123"
login = cleartext "privi123"
group = admin {
default service = permit
[root@dca2-LinuxES tacacs]#
Here is my configuration on the IOS device:
aaa authentication login notac none
aaa authentication login VTY group tacacs+ local
aaa authentication login web local enable
aaa authentication enable default group tacacs+ enable
aaa authorization console
aaa authorization config-commands
aaa authorization exec notac none
aaa authorization exec VTY group tacacs+ if-authenticated none
aaa authorization commands 0 VTY group tacacs+ if-authenticated none
aaa authorization commands 1 VTY group tacacs+ if-authenticated none
aaa authorization commands 15 VTY group tacacs+ if-authenticated none
aaa authorization network VTY group tacacs+ if-authenticated none
aaa accounting exec VTY start-stop group tacacs+
aaa accounting commands 0 VTY start-stop group tacacs+
aaa accounting commands 1 VTY start-stop group tacacs+
aaa accounting commands 15 VTY start-stop group tacacs+
aaa accounting network VTY start-stop group tacacs+
aaa accounting connection VTY start-stop group tacacs+
tacacs-server host 192.168.15.10 key ***
ip http server
ip http authentication aaa login-authentication VTY
line con 0
exec-timeout 0 0
authorization exec notac
accounting commands 0 VTY
accounting commands 1 VTY
accounting commands 15 VTY
accounting exec VTY
logging synchronous
login authentication notac
line vty 0 15
exec-timeout 0 0
authorization commands 0 VTY
authorization commands 1 VTY
authorization commands 15 VTY
authorization exec VTY
accounting commands 0 VTY
accounting commands 1 VTY
accounting commands 15 VTY
accounting exec VTY
login authentication VTY
The question I have is that when I open the browser and enter http://router_IP_address,
the it prompts me for authetication, which password should I use, "exec123" or "privi123"?
Can someone explain to me how this work, and if it works at all? Thanks.
Davidhere is the "debug aaa authen" and "debug aaa author" on the router:
C2621#term mon
C2621#
Feb 25 23:11:33.967 UTC: AAA/AUTHOR/TAC+: (3081244823): send AV cmd-arg=monitor
Feb 25 23:11:33.971 UTC: AAA/AUTHOR/TAC+: (3081244823): send AV cmd-arg=
Feb 25 23:11:34.183 UTC: TAC+: (-1213722473): received author response status = PASS_ADD
Feb 25 23:11:34.187 UTC: AAA/AUTHOR (3081244823): Post authorization status = PASS_ADD
Feb 25 23:11:34.187 UTC: AAA/MEMORY: free_user (0x8276F8AC) user='ddt123' ruser='C2621' port='tty66' rem_addr='192.168.15.1' authen_type=ASCII service=NONE priv=0 vrf= (id=0)
Feb 25 2007 23:11:36 UTC: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 192.168.15.10(49) -> 192.168.15.1(24127), 1 packet
Feb 25 2007 23:11:38 UTC: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 192.168.15.10(49) -> 192.168.15.1(14840), 1 packet
Feb 25 23:11:39.248 UTC: AAA/AUTHEN/LOGIN (00000000): Pick method list 'VTY'
Feb 25 23:11:39.268 UTC: AAA/AUTHOR (00000000): Method=None for method list id=A0000003. Skip author
Feb 25 2007 23:11:40 UTC: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 192.168.15.10(49) -> 192.168.15.1(36781), 1 packet
Feb 25 2007 23:11:41 UTC: %SEC-6-IPACCESSLOGP: list 111 permitted udp 192.168.4.10(2537) -> 192.168.15.1(161), 1 packet
Feb 25 23:11:42.553 UTC: AAA/AUTHEN/LOGIN (00000000): Pick method list 'VTY'
Feb 25 2007 23:11:43 UTC: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 192.168.15.10(49) -> 192.168.15.1(19535), 1 packetu
All possible debugging has been turned off
C2621#
Feb 25 23:11:46.552 UTC: AAA: parse name=tty66 idb type=-1 tty=-1
Feb 25 23:11:46.552 UTC: AAA: name=tty66 flags=0x11 type=5 shelf=0 slot=0 adapter=0 port=66 channel=0
Feb 25 23:11:46.552 UTC: AAA/MEMORY: create_user (0x8276AD88) user='ddt123' ruser='C2621' ds0=0 port='tty66' rem_addr='192.168.15.1' authen_type=ASCII service=NONE priv=0 initial_task_id='0', vrf= (id=0)
Feb 25 23:11:46.556 UTC: tty66 AAA/AUTHOR/CMD(1541751897): Port='tty66' list='VTY' service=CMD
Feb 25 23:11:46.556 UTC: AAA/AUTHOR/CMD: tty66(1541751897) user='ddt123'
Feb 25 23:11:46.556 UTC: tty66 AAA/AUTHOR/CMD(1541751897): send AV service=shell
Feb 25 23:11:46.556 UTC: tty66 AAA/AUTHOR/CMD(1541751897): send AV cmd=undebug
Feb 25 23:11:46.556 UTC: tty66 AAA/AUTHOR/CMD(1541751897): send AV cmd-arg=all
Feb 25 23:11:46.556 UTC: tty66 AAA/AUTHOR/CMD(1541751897): send AV cmd-arg=
Feb 25 23:11:46.556 UTC: tty66 AAA/AUTHOR/CMD(1541751897): found list "VTY"
Feb 25 23:11:46.556 UTC: tty66 AAA/AUTHOR/CMD(1541751897): Method=tacacs+ (tacacs+)
Feb 25 23:11:46.560 UTC: AAA/AUTHOR/TAC+: (1541751897): user=ddt123
Feb 25 23:11:46.560 UTC: AAA/AUTHOR/TAC+: (1541751897): send AV service=shell
Feb 25 23:11:46.560 UTC: AAA/AUTHOR/TAC+: (1541751897): send AV cmd=undebug
Feb 25 23:11:46.560 UTC: AAA/AUTHOR/TAC+: (1541751897): send AV cmd-arg=all
Feb 25 23:11:46.560 UTC: AAA/AUTHOR/TAC+: (1541751897): send AV cmd-arg=
Feb 25 23:11:46.768 UTC: TAC+: (1541751897): received author response status = PASS_ADD
Feb 25 23:11:46.772 UTC: AAA/AUTHOR (1541751897): Post authorization status = PASS_ADD
Feb 25 23:11:46.772 UTC: AAA/MEMORY: free_user (0x8276AD88) user='ddt123' ruser='C2621' port='tty66' rem_addr='192.168.15.1' authen_type=ASCII service=NONE priv=0 vrf= (id=0)no
Feb 25 2007 23:11:47 UTC: %SEC-6-IPACCESSLOGRL: access-list logging rate-limited or missed 976 packets
C2621#
David -
in another room, where the connection is bad to say the least... How do I get the airports to work together? To marry?
If you have not already done so, configure the AirPort Base Station not connected to the router to "extend" the wireless network created by the other AirPort Base Station. Read this for a more thorough explanation:
Wi-Fi base stations: Extending the range of your wireless network by adding additional Wi-Fi base stations
Take note of the following in the above, which I recommend:
If you have configured your Wi-Fi base stations in the past, it may be helpful to do a factory default reset of each Wi-Fi base station that will be part of the wireless extended network before you begin.
As well as the following:
The physical location of extended Wi-Fi base stations will vary according to the building environment and may require some experimentation.
If feasible for your installation, a "roaming network" is the ideal configuration, and precludes the need for experimentation. -
I want to get a Router with a USB port for Home Sharing my library of Music and Movies off a 3TB external HD to my iMac, Apple TV, and iPad so that I don't have to leave my iMac on all the time, but more importantly, I have almost filled the 1TB of memory on the iMac so I need more space. I like my setup using the iPad as a remote to stream movies from the iMac to my AppleTV but I need more space. Thanks.
The iPod and/or MacBook communicate with the Apple TV via WiFi, so there has to be a WiFi network of some sort, even if just an "ad hoc" one set up using a laptop or desktop computer as an access point. If you don't think there will be a WiFi network available, I'd suggest leaving out the Apple TV and just connecting the MacBook or iPod directly to the TV to do your presentation. A MacBook can connect to just about any video input with the appropriate adapter, and the iPod touch can connect via composite or component inputs, or HDMI if it's a fourth-generation iPod touch.
Regards. -
It only connects for minutes at a time. I have not changed my router, modem, or placement of my apple tv, modem, or router. It just suddenly stopped working. Any suggestions?
Mine is doing the exact same problem!
Ever since I rented a movie from itunes with the ATV connected to the internet via wireless (strong signal) from an airport extreme connected to my modem from charter communications (with about 30Mbps speed) it will suddenly stop and by stop I mean it leaves the movie completely and says YOUR APPLE TV IS NOT CONNECTED TO THE INTERNET.
So if I go to my network in the apple tv menu, sure enough my wireless network is missing. But the ipad is finding it, and the imac on wireless is finding it, and it is working. So we hit restart on the apple tv. When it comes back all is good. Then maybe the movie runs ten minutes and it does it again.
In some cases the wireless network reappears but if I select it it still says I'm not connected to the internet.
I have to restart everytime or it will not properly reconnect to the internet or find my wireless net work and actually work and connect.
It has been connected in the same place for a year and never had an issue.
Nothing has changed..... I have not added a wall to cause interference....
My iPad and iPhone show FULL strength.
Please help! -
My ipad 2 appears to be connected to the internet(all bars are up in the left hand corner).....yet I cannot connect to the internet(Safari cannot connect open the page because it is not connected to the internet)
I unplugged my router for 30 seconds and restarted my ipad...still nothing
I really don't think it is my service because my laptop works fine...as I am using the internet right now
I only had this ipad for 2 days
Are there any suggestions that can help solve this problem?Usually it's because you are not making internet connection via wifi.
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Cheers, Tom
Maybe you are looking for
-
I just updated itunes to 10.6. Windows. Vista. (up to date) Everything is the library has gone - no apps, music, videos etc. Playlists have gone. Everything on the iPhone is still there. I can't sync because everything will then get deleted from the
-
How to beat the 32KB limit in AQ messages?
We are using AQ for publishing and subscribing XML messages through InterConnect and have developed a PL/SQL API for apps to use. We use the "normal" design of RAW payload, but the DBMS_AQ.ENQUEUE procedure has a max RAW payload size of 32KB. The pro
-
How do you change the date and time format in Pages
I've tried changing the date and time format a number of times for Pages but it does not change. I'm going to the System Preferences/Language and Text and Formats. I make the changes click on OK and go back to Pages. NO change.
-
Removing duplicates that sync'd to iPhone
forgot to fully remove all duplicate songs that resided on my Mac before I sync'd newly arrived iPhone. Then remembered, completely removed all duplicates on Mac and am not finding a specific sync instruction to allow Mac (10.5.2) music library to ov
-
CS5.1 Camera Raw Unexpected end of file error
I ran into this error a couple of times (the problem would not resolve for these few affected photos) when editing my raw files in my CS5.1 trial. "Could not complete your request because an unexpected end-of-file was encountered." I could not get a