Can u run Airport Express and a wireless modem together?

Can u run Airport Express and a wireless modem together at the same time?
I'm using AE purely for music distribution and have just bought a wireless modem for the internet (not a AE). However I can now only select either the AE network, OR the wireless internet network (it's BT HomeHub). Hence I can either play music or use the internet, but not together!
Any ideas anyone..??
Thanx
David

You should configure your AirPort Express (AX) to join the wireless network provided by the modem. The instructions are in KB 302153, AirPort Express: How to join an existing wireless network in client mode.

Similar Messages

Streaming 3d movies to my Samsung 3DTV using AirPort express and a wireless LAN adapter has not worked. What is my cheapest option for making this happen?

I need a transfer rate minimum of 9mbps. My AirPort express and 3DTV are on different floors, so I cannot directly connect with an ethernet cable. Can I buy an older AirPort express, use it as a bridge, and connect my TV to it via an ethernet cable?

Hi rockchalker,
Thanks for using Apple Support Communities.
For 802.11n Wi-Fi base stations, creating a roaming network is by far the best choice. This will provide the best throughput between the base stations and your Wi-Fi devices.
If you are unable to build the recommended Roaming network, then a Wirelessly Extended Network is the next best option.
For more information on this, take a look at this article:
Wi-Fi base stations: Extending the range of your wireless network by adding additional Wi-Fi base stations
http://support.apple.com/kb/HT4145
Hope this helps,
Mario

I have a MacPro 2008 workstation without Airport or Airport Extreme CArd isntalled. Can I use Airport Express to connect (wireless) to my wireless network? If so, can I then connect my Airport Extreme to my MAcPro by a ethernetcable ?

I have a MacPro 2008 workstation. It has no Airport/Airport card so I have to use an ethernetcable to connect to my modem. As the MAcpro
is in my office in the attic and the wireless modem is in the basement I have a problem. I wonder if it is possible to use Airport Express to connect to the wireless network? Itshould be like this: in my office I connect the MacPro with AE through an ethernet cable. If I can then get AE to connect (wireless...) to my wireless network I should be ablle to connect my MacPro to internet/wireless network. Is this possible???? Any suggestions are very much appriciated. Thank you.

Apple calls this configuration a ProxySTA.
To activate ProxySTA, you must set up the Express to join a wireless network and then enable the Allow Ethernet Clients setting; both settings are located in the Wireless tab of AirPort Utility.

Can't See Airport Express on my Wireless N/work

I have a D-Link DSL G604t router, and have spent hours trying to get it to "see" AE - no joy. I have added the MAC Address to the enabled access list but still nothing - everytime I scan for it, it cannot be found. My Compaq l/top connects no problem to the network, and I cannot find any answers in the manual. Only trying to send itunes to my hifi - don't need to share connections or printers.
Dell Optiplex Windows XP Pro

Hi:
I had a similar problem with a DLink DI-624 wireless router and AirPort Express afew months ago. Here is what you can do.
As an intermediate step, which is undocumented but I found necessary, connect your Airport Express to the wireless router via an Ethernet cable. After the wired connection, your router will definitely see AirPort Express. Then you can go through the normal network registration process. Once this is complete, you can then power off Airport Express and disconnect it from the router and then place it where you originally intended. Once the solid green light comes on (30-60 seconds), you should be able to access AirPort Express the way it was intended, in a wireless manner.
Again, this worked for me after hours of unsuccessful struggling with the installation process as described in the Apple documentation. I hope this helps.
Lawrence

How can I join Airport Express and 2Wire 3600HGV to extend wifi?

I to join an Airport Express to the wifi network from my AT&T 2Wire 3600HGV router to extend the wifi signal. I know it is not SOP to link an AX to a non-Apple device like this. I found instructions ( http://fsdeviations.blogspot.com/2012/09/howto-2wire-3600hgv-airport-extreme.htm l ) for joining an Airport Extreme to the 3600HGV. Has anyone used this or a similar approach with the Express to join and extend wifi from the 3600HGV?

Connect an Ethernet cable from on of the LAN <--> ports on the back of the 2-Wire modem/router to the WAN "O" port on the AirPort Express.
Power up the AirPort Express for a few minutes. The indicator light on the front of the device will be slowly blinking amber at this time.
On your Mac......
Open Finder > Applications > Utilities > AirPort Utility
Click on the Other WiFi Devices tab
Click on AirPort Express
The setup utility will open up and take a minute to analyze the network, then suggest that the AirPort Express will create a new network....which is the correct setting. The window will look similar to this illustration:
For Network Name......type in the exact name of the wireless network that the 2-Wire is providing......IF.....you want to "extend" the 2-Wire network and make one "big" network. If you want to have the AirPort Express provide a different network, type in the name of the network that you want the AiPort Express to provide.
For Base Station Name....type in a device name that you want to call the AirPort Express
Password......If you want to extend the 2-Wire network, then type in the exact same password that the 2-Wire network is using. If you want the AirPort Express to provide a different network, type in a password that you want to use with the network that the AirPort Express will provide
Verify......verify the Password
Click Next, and the utility will set up everything for you automatically.
When you see the message of Setup Complete, click Done. That's it. There should be a green light on the front of the AirPort Express at this point. You can configure other AirPort Express devices in the same manner.

@ Airport Express and BEWAN DSL MODEM : no internet ..why ?

Hello,
I connect a BEWAN ADSL Modem to my Airport Express and create a Airport network to have internet access for my Ibook.
I have choose "Ethernet" for Internet access with DHCP parameter.
Here's what i see : the Bewan ADSL modem give to the airport a public IP for the ip address (that comes from my Internet Provider), a netmask and a router ip that is 192.168.1.1.
On my Ibook, i could connect to the airport (printing is ok) but I couldn't have internet access : blank page under Safari...
My Airport Express has the last Firmware....
I think is a trouble between the BEwan ADSL modem and the Airport because I have Internet access when i directly connect the Bewan Modem to the Ibook.. a routing trouble ?
Do i have to manually enter IP parameter of my Airport ?
Have you the same configuration ?
Thanks for helping me fast.

ouba john,
I'd recomend trying a reset and reconfigure. Your setup sounds pretty simple. Hold in the reset button on your AE until the light blinks, let it restart, and choose your unmodified Airport express from the drop down menu. Run Airport Setup assistant from the Utilitiies menu and try to let that program do all the tweaking for you. Once it's up and running, you can go into the wireless settings with Airport admin and reconfigure security if you wish.
This is "just give this a try" advice. It seems I've heard odd things about ADSL modems, so good luck

How can i run AirPort Express for both a Mac and Windows 2000 SP2?

I have my AirPort Express set up for my iMac and it runs fine. We have a house guest who has a laptop running Windows 2000 SP2. Can I set up Airport so that both computers can access internet wirelessly?

Just did a quick check of the Unofficial Averatec Support Forum. Several posters there upgraded the driver for the wireless card to support WPA on the 5110.
They used drivers from other computer manufacturers and indicated that Averatec has not provided updated drivers.
They were running XP SP2.
Many Averatec models have weak wifi cards. Mine included. Sorry I am unable to be of more help.
Good luck
susan
iBook G4 Mac OS X (10.3.4)

Can AEBS, wired Airport Express and WDS Airport Express devices be mixed?

I have been using an AEBS and three Airport Expresses (non N)in a WDS network using mixed b/g/n with two b/g mac minis, a b/g/n macbook and a b/g macbook for several years but have noticed the speed and reliability flucuating. I wish to do more music streaming and would like to improve the speed and reliabilty.
I have cat5 in several locations in the house.
Can I use the AEBS as a base wired to two Airport Expresses in different parts of the house(probably set as bridge) to extend my wireless g network and stream music to fixed points and then extend the network (?wds) with a non wired Express near one of the wired Express devices?
Thanks
Jim

My Macbook with "n" runs on the 5ghz network...it must be pulling that directly from the AEBS.
So I would guess that your AEBS is actually a simultaneous dual-band 802.11n AirPort Extreme Base Station (AEBSn) ... correct? If so, then it would certainly make sense that the MacBook is connected to its 5 GHz radio.
My wired AXs will be in two very different areas of the house. Is it possible to wire them as bridges, then set each as a WDS base to extend to their local area?
I assume that you intend to create two different WDSs ... correct? If so, this should be possible. You will need at least four AXs to do so. Each WDS would have the main base station connected to the AEBSn by Ethernet; configured as a bridge, and as the main in the WDS. For each of the mains, you would have another AX configured as the remote.
Since the mains are both configured as bridges, all wireless clients connected to either WDS should be able to see clients connected to either WDS or the AEBSn.

Can someone explain AirPort Express and iPhone interaction?

Is it possible to use the iPhone along with an Airport Express? Is there any interaction between these devices? For example can I use the iPhone to control music playback through the Airport Express?
thanks.

Nathan,
Thank you for your reply but can you please provide more details? I'm really confused over Airport Extreme vs. Airport Express vs. Air Tunes and how this all interfaces with the iPhone. Can you please explain these devices? I also saw a post from someone stating they could control wireless music playback via their iPhone, how is this possible?
Edit: See the post by Mike Kelley at http://discussions.apple.com/thread.jspa?threadID=1159025
How is he doing this? Is he using Airport Extreme or Airport Express or Air Tunes?
Message was edited by: EricC617

Can't see airport express in available wireless networks

Looking for assitance in setting up airport express with existing wep encriped linksys router.

There are two options:
1. Create the second profile while on your own network. When you get ready to move the Express, select the profile before disconnecting it from the network.
2. Perform a hard reset on the Express and reconfigure it once you get to your friend's house. If you've already created the profile, you can select the profile after the reset.

Can't install AirPort Express, and unit is flashing amber

Hi,
I've just bought an Airport Express unit, with the aim of playing iTunes remotely (I have a separate wireless connection to the net). I have two problems:
1) When I try to install the Airport Express software provided, the setup tells me that I have a later version of iTunes and cannot install Airport Express. Does that mean iTunes v7.0 (which I am using) already contains Airport Express?
2)My Airport Express unit is flashing amber. Resetting the unit makes no difference. I suspect this is due to the problem of 1) but am really stuck on how to progress!
many thanks in advance!
Mike

Duane,
Thank you for your speedy response!!!!
When I open the AirPort Utility.app, a window opens called AirPort Utility, the twirly/stopwatch icon goes into motion next to the words"Discovering Base Stations." After this happens for some seconds, these words appear...
"AirPort Utility was unable to find any AirPort base stations. Please make sure the AirPort base station you want to set up is plugged in and in range of your computer, and then click rescan to try again."
My express is plugged in five feet from my computer. What to do....?
Many thanks!
Terry

Airport express and comcast telephony modem

I just had Comcast setup cable modem/telephony in my new home.
Technician set up and was only able to get the internet to work if plugged directly from modem into network card on the PC notebook.
I replaced that cable with the airport express, got a green light. both the PC and the mac found the wireless connection and I had internet access from both.
About 2 days later I lost my internet connection. Both machines still find the wireless and report strong connection. but no browser connections.
Interestingly enough, the PC wanted to download some MS updates and was able to do that, but still no connection via IE, Safari, Firefox.
Talked with several techs from Comcast, finally last night I just go the one direct connection with cable working again.
Any other experiences like this??? I want to use wireless and just need to know what the best way to proceed may be.
Thanks,
Bill
imac g5 Mac OS X (10.3.9) also running a powerbook g4

Alexkywalker, Welcome to the discussion area!
Whenever you switch the Ethernet connection from a cable modem from one device to another you need to power down the modem. This will force the cable modem to forget the device it was talking with. The cable modem will then discover the new device and communicate with that.
BTW, the AirPort Express (AX) has an auto-sensing Ethernet port and therefore will work with any type of Ethernet cable.

Configuring my Airport Express and Cisco DCP3008 modem

Hi,
I have an airport express version 7.6.1
and a cisco modem dcp3008 and having issues trying to connect the two. I have called cisco and they told me they would have to reconfigure it for 60 dollars. Is there anyone that has any suggestions for how I could manually figure this out?
My cable/internet service is Charter.... and they can't do anything ha ha.

You can effectively extend the Cisco's wireless network by creating a roaming network with both routers. Note that this would require that both routers be interconnected by Ethernet. Since the Express will perform a new role, be sure to perform a "factory default" reset on it so that it will be in its "out-of-the-box" configuration.

Can't connect Airport Express to existing wireless network!

I just got my new A Express. i try to wirelessly join an my existing network but when it restarts it doesn't see the device. It's i'm trying to set it up so that I can use it as a wireless printer connection for my two macbooks, but all i end up with is the flashing amber light. I've tried a hard reset and that's clearly not solving the problem.
i'd welcome some help as well.

for some reason i had a problem with my airport in my laptop and it couldnt find networks that are hidden.. so that might be the problem the encryption.

Airport Express (and Airport Extreme) shuts down every now and then

So here's the deal,
I'm using an Airport Extreme as my base station (internet, printer, external hardrive). I'm also using an airport express (for airtunes) that is set up to join my existing network that I have created with my Airport Extreme.
Every now and then, the Airport express disconnects becomes non responding and starts to flash yellow. The strange thing is that even though my Airport Extreme is still showing a green light - this does not work either.
To resolve this I must unplug both Airports, restart Airport Extreme and then make my network. After that I can restart my Airport Express and join my existing network and everything works well for a day or 2 and then the same happens again.
What is going on? I mean even though I have found a solution it is timeconsuming and not very elegent. I would rather not have disconnections:-)
Look forward to hearing from you bright guys!
Message was edited by: Skibsted

Skibsted wrote:
I don't think I have a power issue since I have a lot of electronic connected to the same plug and they are working fine.
I have not tried to use the Airport Express alone but I have of course thought about doing that to narrow down the problem.
I don't have inteference.
How do I check if my neighbours are using the same channel?
There are a couple of programs out there. The one I have used is called iStumbler. http://www.macupdate.com/info.php/id/11753. This will show the networks around you and the channels they are using along with other things.
The distance from the AEX to my Airport Express is like 10 inches!
Having an access point close real close to a client will cause some interference itself. Also you had mentioned you had the AEX plugged into the same stip or outlet with other equipment. This can also cause interference and issues.
The firmware is the latest.
I can say that I think I have found a solution though. When I install my Airport Express I hit the "use to extend my network" instead of hitting "join existing wireless network".
It had been working flawlessly ever since (4 days)
I think extending a wireless network is only used if you have 2 AEBS or more. You would use WDS to extend the range when using an AEX but since you are not using it for that you set it right by joining a network.
Thanks

Can u run Airport Express and a wireless modem together?

Similar Messages

Maybe you are looking for