Can we connect a Cisco videoconference system to adobe connect?

One of our participants wnt to use his own CISCO C20 videoconferencing system as a source for better video quality. Is it possible to connect Cisco C20 with Adobe Connect and if "Yes", what are the technical advices for the connection.
Best regards,
Martin

If you have an on-premise deployment of Adobe Connect you could see if you could configure to the Cisco system to work through the VTC integration, Configure FMG for a video telephony device. However, the Cisco C20 is not one of the supported systems, so it may or may not work.
If you are on a hosted deployment, then you don't have the above option. You could get the video/audio feed into a computer and display it in the Video pod. This may not improve the video quality as the Video pod is limited to its preset resolutions (up to 240p) and frame rates. You may also need to use DVdriver to get a Windows computer to recognize your video input as a webcam.
Third option would be to explore using one of the external video pods available here, Adobe Connect | Apps. You will likely need to do some setup outside of Connect to get them to work, but it could be worth exploring. There are two there that may work: TalkingStick and tecRacer VideoPlayer.

Similar Messages

Can I create a User Registration System in Adobe Muse?

Hello community!
I was wondering if I can create a User Registration System in Adobe Muse? I do NOT use Dreamweaver, and I know Dreamweaver can do it. I am not a coder, but there are plenty of tutorials online for me to follow step-by-step. I just can't seem to find anything for Muse.
Since Muse has Insert HTML, I was wondering if anyone has figured out a way to create a User Login and Password protected page.
Thanks!
Joe~

Hi,
There are multiple threads in this issues
Login page using Muse and BC
Re: Is there a way to make private (members only) areas through muse?
Re: Can I create a login/password protection in Muse for a HTML5 page or two?
How do I create a password protected entrance page for a muse site?
Do let me know if you have questions further.

Can not connect computer to Cisco Connect -EA3500

Can not connect computer to Cisco Connect -.Receive error msg 82BD0305. Reset to EA3500 to default and reinstalled software.

Reading the manual it says the username is blank, password 'admin'.

How can I connect my iPad to home sharing system

How can I connect my iPAD to th ehome sharing system?

Try this:
1. Turn router off for 30 seconds and on again (if possible)
2. Settings>General>Reset>Reset Network Settings
3. Reset iPad; hold the Sleep and Home button down until you see the Apple Logo

How can I connect ATV to my Bose Lifestyle 8 system?

How can I connect my 3rd generation Apple TV to my home theater BOSE Lifestyle 8 system (1999)?
In the BOSE reciver there isn't optical output just analog.
what the solution for this issue?

The problem is with the Bose bar and not the Apple TV . I have confirmed that sound is Transmitted from both the HDMI output and the Optical (Toslink) output simultaneously from the Apple TV
The BOSE bar AUTOMATICALLY selects the best quality signal . You can't select it. So HDMI will win and once the TV is off, audio will not work.
The AUX port is essential useless as Bose told me its for "Redundancy" and you can't "select" to use it.
What you need is an optical selector . I bought this one for around $20 from amazon . I like it because its black and you can connect up to 4 devices.
http://www.amazon.com/gp/aw/d/B005BXVB3G
Because the Bose bar inputs from the Optical out on the back of the TV, have it now go through the selector. Your Apple TV can be input 2 .
You can now watch TV or Apple TV normally but if you want to still hear the music from Apple TV , manually change the selector to input 2 on the optical selector device . When you turn off TV it will still play sound coming from apple tv's optical output .
Works perfectly ! Cheap work around . Unfortunately for such an expensive Bose device you shouldn't need to buy "work arounds" but I'm very happy with the sound quality and I'm a Bose believer . So it was worth doing .

I hate the new operating system. Can't connect to wifi in home anymore even after a restore. Rhapsody no longer works on my phone either. Plus the brighth graphics are bothering my eyes even with brightness turned down. Any ideas on why rhapsody doesn't w

I hate the new operating system. Can't connect to wifi in home anymore even after a restore. Rhapsody no longer works on my phone either. Plus the brighth graphics are bothering my eyes even with brightness turned down. Any ideas on why rhapsody doesn't why rhapsody doesn't work anymore?

Contact Rhapsody to see if they have or plan to release an update for the app. Try uninstalling and reinstalling the app. Have you tried resetting your device by pressing and holding the Home button and power button until the silver apple appears?

I can't connect to Wi-Fi - keeps timing out. No problem connecting from other laptops / phones. Stopped working after I did a system upgrade. What can I do?

I can't connect to Wi-Fi - keeps timing out. No problem connecting from other laptops / phones. Stopped working after I did a system upgrade. What can I do? I am on OS X Yosemite.

Take each of the following steps that you haven't already tried, until the problem is resolved. Some of these steps are only possible if you have control over the wireless router.
Step 1
Turn Wi-Fi off and back on.
Step 2
Restart the router and the computer. Many problems are solved that way.
Step 3
Change the name of the wireless network, if applicable, to eliminate any characters other than letters and digits. You do that on your router via its web page, if it's not an Apple device, or via AirPort Utility, if it is an Apple device.
Step 4
Run the Network Diagnostics assistant.
Step 5
In OS X 10.8.4 or later, run Wireless Diagnostics and fix the issues listed in the Summary, if any.
Step 6
Back up all data before proceeding.
Launch the Keychain Access application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Enter the name of your wireless network in the search box. You should have one or more "AirPort network password" items with that name. Make a note of the name and password, then delete all the items. Quit Keychain Access. Turn Wi-Fi off and then back on. Reconnect to the network.
Step 7
You may need to change other settings on the router. See the guidelines linked below:
Recommended settings for Wi-Fi routers and access points
Potential sources of interference
Step 8
Make a note of all your settings for Wi-Fi in the Network preference pane, then delete the connection from the connection list and recreate it with the same settings. You do this by clicking the plus-sign icon below the connection list, and selecting Wi-Fi as the interface in the sheet that opens. Select Join other network from the Network Name menu, then select your network. Enter the password when prompted and save it in the keychain.
Step 9
Reset the System Management Controller (SMC).

Can we connect another system say SRM,BI with persona(without add on)

Hi ,
I have installed SAP Screen Persona's in one my ECC system ,so can I connect the sap persona's to other landscape system for ex SRM ,BI etc without installing any add on it ?As in same ECC system one system we can take main system and other as target system so can i take a SRM system as target and persona's will work on it.Kindly clarify Sushant Priyadarshi any comments.
Thanx
Niti

Hi Niti,
In config guide for Persona 2.0 under the section maintained system SAP has clearly mentioned that you can make your one system for ex (ECC) as a source system and then connect your other system as a target by maintaining logical system in SPRO only prerequisite should be your SAP kernal should be 7.21 or 7.40 or higher
Follow the procedure for the SPRO configuration and after that just do the below configuration
Maintain the following parameters under System Settings:
o Service.Uri – Maintain the service name for accessing SAP Screen Personas
here. The default service is /restgui.
o Server.Url – Maintain the server link for the system here. For example:
https://ldfss600.pal.ess.corp:50015
Go thorugh the config guide for detailed steps by clicking below link
https://websmp202.sap-ag.de/instguides
Regards,
Prasad Deshpande

My HD TV has two HDMI inputs which are being used by a home theater system and my RCN cable box. i want to be able to use my appleTV as well as those but do not have another HDMI input. How can i connect it so that i can use any 1 of the 3 at any time?

My HD TV has two HDMI inputs which are being used by a home theater system and my RCN cable box. i want to be able to use my appleTV as well as those but do not have another HDMI input. How can i connect it so that i can use any 1 of the 3 at any time?

Get an HDMI switcher. Plug in the ATV directly to the TV and then use the switcher on the other input.
Example
http://www.amazon.com/Ultra-High-Performance-Switcher-Switch/dp/B0015YWKYY/ref=s r_1_1?ie=UTF8&qid=1316918064&sr=8-1

How can I connect a Cisco 7940 phone to a trixbox via SIP

how can I connect a Cisco 7940 phone and CIsco 7970 to a trixbox via SIP

...by configuring the trixbox according to the required configuration and changing your firmware on the phones to SIP{
=============================
Please remember to rate useful posts, by clicking on the stars below.
=============================

Can we connect 2 ECC to a single PI system.

hi ,
can we connect 2 ECC to a single PI system. here we would be using proxies in the 2 ECC.
Is it possible to enable the SProxy for both systems.
EG: ECC1< -> PI (A)<-.>APO
ECC2<-->PI (A)<-.>APO
Regards,
Praveen K
Edited by: praveen kalwa on Jul 29, 2010 5:34 PM

Yes. you can connect 2 ECCs to a single PI system.
You have to create two entries for Proxy in sm59.
Please refer the below document for the proxy configuration.
(Put 'Proxy configuration in SAP XI' in Google Search & You will get a document from saptechnical.)
If everything goes fine, from both the ECC systems you can see the PI interfaces(Transaction : SPROXY) and implement them.
Edited by: soumen patra on Jul 29, 2010 3:42 PM

Can we connect one R/3 to two BW systems and extract data?

Can we connect one R/3 to two BW systems and extract data succesfully ? kindly through light on this issue.
Thanks and regards.
Ankush Shejul

Of course you can.
Just have to have the RFC destinations in place and use the
CALL FUNCTION '....' DESTINATION '....'
commands in ABAP, check out the ABAP forums for more info.

How many BW 7.3 systems can be connected to one HANA database?

Hello Gurus,
For Development,Test and sandbox environments customer likes to share one HANA database for multiple SAP BW systems.
So how many BW 7.3 systems can be connected one HANA database (ofcourse on single HANA appliance)?
Can i install multiple HANA Databases on single HANA hardware?
Can someone help me on these questions.
Thanks.
Srikar

Hello,
i would suggest reading this blog:
How BW-on-HANA Combines With Native HANA
sap_user_union_001 wrote:
Today, HANA 1.0 SP3 was released.
I was not able to find it in downloads - are you sure it is already released?
sap_user_union_001 wrote:
You can connect as many systems as you want with the HANA (also 3 BWs).....The problem is, that you only have 1 system, which is able to put the data real-time into the HANA via SLT...the other systems will load their data via ETL into HANA...
I am not aware about any such restriction. It should be possible to have as many SLT systems replicated as you like. Can you explain why only one SLT is possible?
Tomas

Can FDMEE connect to oracle table as source system?

Can FDMEE connect to oracle table as source system?

Hi Experts ,
I am new to FDMEE .
I am loading data from Oracle RDBMS to Essbase/Planning using Open Interface Adapter , as per the steps mentioned in the Erpi_admin guide , i have populated the AIF_OPEN_INTERFACE table with data and configured FDM stuffs ( Mappings , Import Format , Location , Data Rule etc ) . During IMPORT getting the error "
2014-01-28 17:45:24,018 FATAL [AIF]: Error in CommData.insertImportProcessDetails
Traceback (most recent call last): File "<string>", line 2304, in insertImportProcessDetailsRuntimeError: No periods were identified for loading data into table 'TDATASEG'."
Just to confirm that i have done the Period Mapping as well .
Please guide me to load the data using Open interface adapter .
Thanks,
Amit

Can we connect to any SAP system if we have connection details.

Hi Experts,
Can we connect to any SAP system if we have connection details.
In this thread I found Diego Lombardini asking connection details.
Needed help on this report
I am working in ABAP for couple of years but donu2019t have much idea about connection to SAP system, Please let me know how it is possible .
High points will be rewarded for any helpful answer.
Regards
Bikas

Hi Bikas,
That reply is just because Diego got irritated by Ravi asking the same question in many threads many times .
Otherwise if a SAP server is not secureed using secureclient you can always connect to that SAP system using the internet and your own SAP GUI ( perhaps based on the GUI compatibility )
But i bet, nobody will reveal SAP server as open for you.
Cheers
Kothand

Can we connect a Cisco videoconference system to adobe connect?

Similar Messages

Maybe you are looking for