Can we get 2 different types of SPC charts for an MIC in an inspection plan

Hi All,
1. Can any one help me out in getting 2 different types of SPC charts for a single MIC in an insp. plan.  As each MIC can take only one Sampling Procedure and as SPC chart type is assigned to Sampling Procedure I am not able to get 2 different types of charts. Is it possible in SAP if so can you let me know how.
2. Can we plot SPC charts of 2 different MICs of same chart type on single graph via SAP?  I tried QGC3 but was not successful.
I appreciate your help.
Thanks,

YES,
You can get two different SPC characteristics.
May be a crude method, but definite solution.
1. You create one characteristic say '0010' with control indicators suitable for SPC characteristics. Assign sampling procedure to this characteristic with chart type say '175 Shewhart chart for np/USA'
2. Now create another sampling procedure with chart type say '520 Moving Average Chart'
3. Now select characteristic line '0010' in the plan.
4. Click copy characteristic & press enter. The characteristic gets copied with same control indicators.
5. For this new characteristic '0020' set 'Calculated characteristic'
6. In formula field enter formula as A00020*1. (where A0 is Measured value for single unit.
7. Now assign the new sampling procedure to this characteristic.
8. Done... Now when you record the results for characteristic '0010', after valuating press 'EVALUATE FORMULA' button... & the same results of '0010' are copied for characteristic '0020'
Thus you have two SPC charts for same results without re-entering it.
Hope this is helpful.

Similar Messages

  • SPC chart for Qualitytative MIC?

    Hi All,
    1)Please suggest me SPC chart will also valid for Qualitytative MIC?
    2)Whats are ohers charts are possible in QM?
    Regards,
    sid

    Per my knowledge, SAP does not have SPC charts for Attribute / Qualitative characteristics. Even if you want to do the analysis outside of SAP, through QM - STI interface, this interface does not support qualitative characteristics.
    Other charts you have is Histogram, Run charts. If you are in higher versions of SAP (EHP 2), SAP has given a new **** pit for evaluations, you can access it thru QGA4. Check OSS, SAP has released a consulting note on this. You can do variery of analysis and various chart options are available in this **** pit.
    I hope this helps.
    Thanks,
    Ram

  • In the new Numbers, How can I get a 2D stacked column chart to display only 1 column?

    In the new Numbers, How can I get a 2D stacked column chart to display only 1 column?

    This is one of those things that I find really strange about Numbers 3. The control for what you want to do is not where anyone would expect to find it.
    Select the Chart
    Click on Edit Data References
    Look at the bottom left corner of the Numbers window. It should say "Plot Columns as Series" or "Plot Rows as Series"
    Click on it and change it to the other

  • Can U Get Different Key Colors For pro 13"

    Can U Get Different Key Colors For pro 13"

    Can you do something in the javascript code where you have given specific IDs to each buttons in your menu? It could end up in something like "$('#menu_id').css('background-color', '#1B3E70');"
    Or, let say you have controls defined like thie:
    <body>
    <ul class="menu">
    <li class="menu-item"><a>item 1</a></li>
    <li class="menu-item"><a>item 2</a></li>
    <li class="menu-item"><a>item 3</a></li>
    </ul>
    </body>
    Can't you write at render stage this kind of actions by index:
    var i = $("li").index( $(this).parent() );
    if ( i === 1 ) {
    $('body').css('background', 'red');
    } else if ( i === 2 ) {
    $('body').css('background', 'green');
    } else {
    $('body').css('background', 'brown');

  • How can i produce this type of line chart (yield curve) by using flex2 charting?

    help! I am a flex newcomer, how can i produce this type of
    line chart (yield curve) by using flex2 charting? Anybody can teach
    me how can i customize the width of each scales as below of line
    chart? anybody know this?
    Click
    Here To See

    I need to show the X and Y Co-ordinate in a message when I click on the graphic's point.
    thanks for the tips, I´ll try to understand the sample program.
    Noguti

  • In KA02 screen how can I get different functional area like (Production, Sales, Adminstration etc)

    In KA02 screen how can I get different functional area like (Production, Sales, Adminstration etc)

    Hi,
    Please check below configuration for defining functional areas for cost elements
    SPRO> FI > FI Global settings> company code> cost of sales accounting>Functional area > enter functional area
    Regards,
    Jyoti

  • Where can I get a list of available selection for certain dict type?

    Where can I get a list of available selection for certain dict type in code?  For instance, when I use SE16 to view VBFA table, I am presented with many filter criteria.  One of them would be "VBTYP_N".  When I click on the square next to the option, I am presented with a list of possible values to select from.  Where can I get the list of this possible values for any given dict type in code?

    Hi Frank,
    The list of possible selection you see can be from diferent sources
    1) Search helps defined either programatically or search helps defined at table level.
    If it is a Z Selection screen check the program, then the data declaration of the parameter
    2)Check tables provided at field level. They can be through use of foreign keys. The proposal generated could be simple compund ..
    3) Fixed values at Domain level ()
    Please refer to this link as well for detailed explanation
    [http://help.sap.com/saphelp_470/helpdata/en/9f/dbaa5435c111d1829f0000e829fbfe/content.htm]

  • I am using windows 7 and can't get the print drives to load for F2210 printer

    I am using windows 7 and can't get the print drives to load for F2210 printer and I keep receiving different fatal error codes.

    Hello @Imvertical 
    Welcome to the forums!
    I read about how you're attempting to install your Deskjet F2210 on your Windows 7 system and receive Fatal Error codes. I will do my best to help and make some suggestions for you to try. 
    To being, try a standard copy from the unit to see if it will copy. If copies work, continue troubleshooting. If not, let me know what happened when you made a copy.
    Next:
    Perform a Level 3 uninstall.
    There are 2 ways you can run the uninstall:
    From Original installation CD:
    1. Insert CD into drive, and then cancel the installer
    2. Click Start and open 'Computer', and then right click on the CD drive and open
    3. Open folder Util
    4. Open folder CCC
    5. If you have an HP computer run the L3uninstall.exe. If you have a non-HP computer run the L4uninstall.exe
    6. When the uninstall has completed restart the computer
    7. Run Disk cleanup from Accessories\ System Tools
    8. Download and install the latest version of Adobe flash player
    http://www.adobe.com/support/flashplayer/downloads.html
    9. Download the full feature software and drivers: HP Deskjet F2200/F2224 All-in-One Printer series Full Feature Software and Driver
    10. Run the download to reinstall the printer
    If software was downloaded and extracted to your system:
    1. Click Start and type %temp% in the run field
    2. Look for, and open the folder starting with 7z (Example: 7zS2356) (If there is more than one, choose the most recent folder)
    3. Open folder Util
    4. Open folder CCC
    5. If you have an HP computer run the L3uninstall.exe. If you have a non-HP computer run the L4uninstall.exe
    6. When the uninstall has completed restart the computer
    7. Run Disk cleanup from Accessories\ System Tools
    8. Download and install the latest version of Adobe flash player
    http://www.adobe.com/support/flashplayer/downloads.html
    9. Download the full feature software and drivers: HP Deskjet F2200/F2224 All-in-One Printer series Full Feature Software and Driver
    10. Run the download to reinstall the printer
    Please let me know if the installation worked after the Level 3 uninstall.
    Good luck and have a nice Wednesday!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • Can we capture two types of Serial Numbers for a material?

    Hi,
    I have scenario where i need to capture two different types of serial numbers for a material. This scenario is very similar to the below one -
    Say if a CAR is a serialized material, then i want to capture engine no. and chasis no. for each car.
    I know in standard serial number management, we can capture one kind of serial no. for an item, but can we capture two types of serial number for an item? If yes, how we can do that?
    Please help.
    Thanks,
    Parimal.

    Hi,
    No it is not possible to have two serial numbers for a material.
    The main attribute of a serial number is that it is UNIQUE.
    You can better have the vehicle number as the required serial number and the other numbers under the Manufacturer data of the General data tab of the IQ01 transaction. ( Equipment master creation ).
    You can better change the name of the manufacturer data such as Model number to Engine numeber and Manu serial no to Chasis no etc.., using CMOD transactions.
    Regards

  • HT201304 I have forgotten my "restrictions code" passcode. How can I get a new passcode? Thanks for your help. Paul

    I have forgotten my "restrictions code" passcode. How can I get a new passcode? Thanks for your help. Paul

    If You Are Locked Out Or Have Forgotten Your Passcode
    iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
    iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
    iOS- Understanding passcodes
    A Complete Guide to Recover Your iDevice if You Forget Your Passcode
    If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
    Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
    Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
    Follow these steps to restore your device:
         1. Verify that you are using the latest version of iTunes before attempting to update.
         2. Connect your device to your computer.
         3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
         4. Select the Summary tab.
         5. Select the Restore option.
         6. When prompted to back up your settings before restoring, select the Back Up
             option (see in the image below). If you have just backed up the device, it is not
             necessary to create another.
         7. Select the Restore option when iTunes prompts you (as long as you've backed up,
             you should not have to worry about restoring your iOS device).
         8. When the restore process has completed, the device restarts and displays the Apple
             logo while starting up:
               After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
              to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
              iOS, keep your device connected until the "Connect to iTunes" screen goes away or
              you see "iPhone is activated."
         9. The final step is to restore your device from a previous backup.
    If you can not restore your device then you will need to go to recovery mode.
    Placing your device into recovery mode:
    Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
         1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the other end
             of the cable connected to your computer's USB port.
         2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the
             red slider appears, then slide the slider. Wait for the device to turn off.
              If you cannot turn off the device using the slider, press and hold the Sleep/Wake
              and Home buttons at the same time. When the device turns off, release the Sleep/Wake
              and Home buttons.
         3. While pressing and holding the Home button, reconnect the USB cable to the device.
             The device should turn on. Note: If you see the screen pictured below, let the device
             charge for at least ten minutes to ensure that the battery has some charge, and then
             start with step 2 again.
         4. Continue holding the Home button until you see the "Connect to iTunes" screen.
             When this screen appears you can release the Home button.
         5. If necessary, open iTunes. You should see the following "recovery mode" alert:
         6. Use iTunes to restore the device.
    If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
    Additional Information:
    Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

  • Can I get a discount on Adobe Photoshop for mac if I own cs6 for windows?

    Can I get a discount on Adobe Photoshop for mac if I own cs6 for windows?

    It might be possible, though you will have to check with Adobe directly.  Normally, an upgrade involves going from a product to a product or from a suite to a suite, but not a product to a suite or vice versa.  And I don't know that this would be an upgrade since you are moving laterally rather than up.  I have heard of exceptions being made, so your best bet is to contact someone who has the ability to work out a deal with you.
    I am pretty sure that if you had a Creative Cloud subscription the question of Mac versus PC is moot as you can have installations for both machines with the subscription.  But Creative Suites are different animals.

  • Can't get and use an apple id for cloud or apps or store when i try to change it it will let me but then everytime it keeps asking me to chang e password everytime cant get my computer to just accept one password that will keep

    can't get and use an apple id for cloud or apps or store when i try to change it it will let me but then everytime it keeps asking me to chang e password everytime cant get my computer to just accept one password that will keep

    Just what are you doing and what is the exact wording of the message you are getting?

  • After deleting a song from my iPhone, it still playing. How can i stop that? How can i get rid of the song once for all?

    After deleting a song from my iPhone, it still playing. How can i stop that? How can i get rid of the song once for all?

    I'm pretty sure that the solution is in the settings of her email

  • I do not have a high speed internet connection. How can I get Mountain Lion on a disk for install?

    I do not have a high speed internet connection. How can I get Mountain Lion on a disk for install on my 24" Imac?

    As long as you use your Apple ID to purchase it, I don't see why they wouldn't let you download the installer on one of their Macs and put it on a pocket drive.
    Or, a friend with a high speed connection?
    I agree with you about the delivery method, just trying to help you get what you want.

  • Time Machine on my iMac won't open iPhoto. It goes to desktop screen automatically. When I select User/Picture/Iphoto library it only brings up the preview page with the size of the folder. I can't get into the library to look for lost photos.

    Time Machine on my iMac won't open iPhoto. It goes to desktop screen automatically. When I select User/Picture/Iphoto library it only brings up the preview page with the size of the folder. I can't get into the library to look for lost photos.

    Thank You. This helps me alot to get into the masters and to see events and photos in a utilitarian way, but it is not as easy as viewing the normal iphoto format to find photos.  Can I do something else or did I not do something right to not see normal iphoto in Time Machine ?

Maybe you are looking for