Can we use SPA-4XOC3-POS-V2 on 7600-SIP-400

Hi,
We have ordered 2 x SPA-4XOC3-POS to use on 7604, we have received SPA-4XOC3-POS-V2 from our supplier.
I know that the SPA-4XOC3-POS-V2 are for the 12000, is there a way to use them on a 7600-SIP-400??
Any help is appreciated.
Thank you.
Hitch

This SPA is not supported on SIP-400 on 7600s. You need to get a NON V2 SPA.
Atif

Similar Messages

VPLS - SPA-4XOC3-POS - Core Facing ?

Hi NetPros,
I know this topic has been discussed many times in forum and I could find useful information on specific hardware support in 7604.
However my requirement is bit strange (as it sounds to me). I have the below hardware:
7604 chassis
Sup 720-3B
SIP 400
SPA-4XOC3-POS
WS-X6516A-GBIC
As I gone through the forum, I understood the only constraint in 7604 with VPLS is that the core facing should be either SIP-400/SIP-600 with Gigi SPA, ES-10G and OSM.
1. But my problem now is I have SIP-400 with SPA-4XOC3-POS. Can this SPA be used on wan facing side for MPLS to work. To my understanding, core should only do label swapping and not mandatory that core facing should be Gigi. Though my typical core facing PE (NPEG1 now) side is only on Gigi, in this case of VPLS with 7604 I dont have Gigi and have to purchase so thought if SPA-4XOC3-POS works then atleast I go ahead and test VPLS. Procuring Gigi SPA will take some time due to business approvals.
2. If only Gigi SPA should be on the core facing side, then which Gigi SPA should be supported. Will 1 Gigi SPA support or I have to go for 10 Gigi SPA?
thanks
Arun

Hi Arun
--- > Can this SPA be used on wan facing side for MPLS to work. To my understanding, core should only do label swapping and not mandatory that core facing should be Gigi.
As per my understanding you what to configure VPLS on POS interface facing towards CE.
Or You want to use POS for Core facing i.e. internal network towards " P "
If towards "P" then yes it should work because xconnect vfi require L3 that is IP routing to reach other end and that can possible via static configuration or via BGP auto discovery.
and If towards CE then i don't think it work. Below is the specification.
I have not tested but if possible you can check weather you will get any command "xconnect vfi " under POS interface that connect towards CE.
As per my understanding you can terminate VPLS link using Access Port , Trunk Port , Dot1q Tunnel for CE.
just check !!
mpls label protocol ldp
mpls ldp logging neighbor-changes
mpls ldp router-id Loopback0
l2 vfi l2vpn manual
vpn id 1
neighbor 10.0.0.2 encapsulation mpls
neighbor 10.0.0.3 encapsulation mpls
neighbor 10.0.0.4 encapsulation mpls
int loopback 1
1.1.1.1 255.255.255.255
And try to configure xconnect vfi under POS interface . But i don't think because VPLS Provide L2 service .
Regards
Chetan Kumar
http://chetanress.blogspot.com

Port Analizer Port gigabit cisco 7600 SIP-400 SPA-5X1GE-V2

Hi,
I have a Wan LINK (Layer 3), so I want to check if there are retransmissions in this link.
Do you know if there is a way that a can do SPAN on a GigabitEthernet Port on SPA-5X1GE-V2 (Cisco 7600 Platform)
I tried but i got this error:
R(config)#monitor session 10 source int GigabitEthernet 4/0/0
% Interface(s) Gi4/0/0 not supported as monitor source(s) on this platform
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 15.1(2)S, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
4    0 4-subslot SPA Interface Processor-400 7600-SIP-400
5    2 Route Switch Processor 720 (Active)    RSP720-3CXL-GE
4/0 5xGE SPA                    SPA-5X1GE-V2
thanks for the Help.

Hi,
Does anyone have any suggestions?

Can i use pos 622M as a pos 155M interface, module is SPA-1XOC12-POS

SPA-1XOC12-POS can use as a 155M sdh POS interface?
this is on 7609 sip 400,not a channelized oc 12 interface.
if i connect a 155 M sdh line into this 622M interface,it is single mode fiber. does this work?
thank you!

Hi flyjunli,
I'm quite sure this won't work. The framing won't fit if you connect different interfaces.
BR
Sebastian

Can't use procedure in the .rdl file.

Hi experts,
I created a simple River project, and I can active the project successfully.
But when i added some codes to call a procedure, then i can't active the rdl file.
This is the code I used to call a procedure:
action callExternalProc2() : DecimalFloat[]
      let x = sap.hana.catalog.RIVERPRJ.MY_PROCEDURE_TEST3();
      return x;
The error message met when active the project is:
A transaction rollback may have left the object in an inconsistent state.
exception 40183:
repository/base/activation/activator.cpp:884
Transaction rollback detected. Activation failed.
When i commented the above codes, the activation will be successful.
And the procedure can execute in SQL console.
Can you give me some suggestions?

Hi Omer,
I tried to create my stored procedure in another schema(owned by my user), but I still can't active the rdl file.
Also, I can't execute the following sql statement using my user or the system user:
       set schema "RIVERPRJ";
       grant execute on MY_PROCEDURE_TEST3 to _SYS_REPO with grant option;
The error message is:
     Could not execute 'grant execute on MY_PROCEDURE_TEST3 to _SYS_REPO with grant option' in 10 ms 659 µs .
     SAP DBTech JDBC: [258] (at 17): insufficient privilege: Not authorized to grant the privilege on the procedure: line 1 col 18 (at pos 17)
If I active the rdl file, the error message is as follows:
In the procedure, if I do some queries from the tables created by the rdl, it did not work, but it works if I do some queries from the tables which were not created by the rdl file.
I think this maybe the reason for the error message "A transaction rollback may have left the object in an inconsistent state." .
In my opinion, I think we can not use a stored procedure that do some queries from tables created by the rdl entities.
Because create the entity and call the procedure at the same time may left the object in an inconsistent state.
Put the queries in an action is ok, but the river can not support some key words like "lag over",.
So i am trying to put these things in a procedure and call it in the action.
If we can't use procedure, how could I use some sql key words like "lag over"?
Could you give me some suggestions?
Thanks very much for your help.
Regards
Eric

Broken screen can I use a projector?

Hello,
On a flight to switzerland my screen was crushed on the airplane .... now in Switzerland and want to use my computer but the screen is not useable at all, if I buy cables can I use my computer by hooking it up to a projection screen or tv?
If I order a new mac book from Switzerland can I order a North American one and have it delivered here? Help, I have 50 GB of photos to load up and edit!!!
Sadly,
Equinepics

>If I order a new mac book from Switzerland can I order a North American one and have it delivered here?
Speak to your local store and ask the question. This is just a user to user forum. Don't forget, new machines typically run Lion, and are not downgradeable to Snow Leopard. If you have any PowerPC applications, this could pose a significant problem, since there is no Rosetta in Lion. See my three FAQs before jumping to buying the wrong machine:
http://www.macmaps.com/usedrefurbished.html
http://www.macmaps.com/upgradefaq.html
http://www.macmaps.com/macosxnative.html
>if I buy cables can I use my computer by hooking it up to a projection screen or tv?
Most Macs offer that compatibility, but you have to be careful which cables to get. I'm assuming the problem machine is a MacBook Pro? Do you know what age the machine is? We need to know the week and year of the machine. You can get this by finding its serial number, and reading off the 3rd, 4th, and 5th character of the serial number. All other parts of the serial number are key to your warranty, and should NOT be stated on the forum.

Can I use 3D in PS CC?

Can I use 3D in PS CC?
If so why is it grayed out?
What image format does it recognize?
Will it render a multi level image with a flat back? Like a family crest with florals, helmets, crosses, castles and such?
I have the Cloud and both Photoshop CS6 Extended and the CC version. Both have 3D grayed out.
I have Win 7 Ultimate 64 bit, 4 gb of RAM, dual core 3.2 Gb CPU. Over 3 Tb of external HD's.
I use Poser 9, DAZ 3D 4.6, Silo 2.2, CrazyTalk 7, and Flash CS6/CC.
I work with 2D manipulation of family charactures and would like to make an excellent head and hair model for my animations.
Thank you in advance,
Whettenhall

The 3D features can be disabled on older OSes, or if your video card doesn't meet the minimum requirements.
We have seen a few users with the 3D features disabled because of corrupted activation/licensing info.

BAPI_PO_CREATE1 use of potextitem in tables can i use this to populate text

hi
i nedd to know BAPI_PO_CREATE1 use of potextitem in tables can i use this to populate text at item level
as my requirment is to populate the item text at item level in me23n tcode
so how to use this pls suggest and how to acheive it?
under me23n tab text at item level bottommost section item text i need to populate
regards
Nishant

Hi,
in fact my price values were not so small - 2.15, 1.55, 2.45, etc... but nothing less than 1.00. Nevertheless, you pointed me to the right direction - to search OSS for the answer. OSS Note 571860:
https://websmp230.sap-ag.de/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/sapnotes/index2.htm?numm=571860
helps me to find out what I missed in my scenario: I didn't set ITEM-NET_PRICE at all, just via condition table. Now, when I added the following:
item-net_price = some_price. itemx-net_price = 'X'.
item-po_price = '2'. itemx-po_price = 'X'. " <-- in fact, PO is created even without this line
all of my POs are created with correct prices from the input.
Problem solved.
Thanks!
Ivaylo

How can i use capacity reservation group

I have a set of slow moving SKU which i want to plan in a specific week every month , I know i can use PPC calendars for that but how can i use capacity reservation group in SCM 7.0 to achive this through wave heuristic
Please advise
Prasanna NBaware

Hi Ambrish,
PPDS capacity reservation functionality available from version SCM 5.1 onwards. for your requirement you can reserve the capacity at resource level for product.
To archive this requirement, you need to do
u2022Create Planning Object Structure (POS) with the required characteristics (Product & Location mandatory)
u2022Create a planning area assigning the planning object structure
u2022Create Characteristics Value Combination (CVC) in the POS
u2022Maintain Capacity Reservation Group (resource)
u2022In Product Master > Demand Tab> assign the consumption group
Result: . Planned order gets created for the demand based on the allocated quantity for the particular period
please let me know if you have any further question
bye
Dhaiva

Can I use a T-shaped connector with my MacBook Air 1st generation?

My charger recently stopped working and I was able to get a quick replacement. However, it's one of the old models of chargers with the T-shaped connector. WIll it still work with my MacBook Air. I know it's slanted downwards so that might pose a problem. Any answers or advice?

The Magsafe 1 connectors can be used both the T and the L.
The new Magsafe 2 connectors can't because they don't fit.
http://support.apple.com/kb/HT2346

Can i use one single fibre to make a DPT ring.

i don't want protection , may i just user one outer ring or inner ring to make a DPT ring.
can i use DPT line card as a normal pos interface
thank you!
tom

"may i just user one outer ring or inner ring to make a DPT ring"
As per my knowledge DPT will not work in one fiber. As data flows in one fiber and control in other.
As far as i know even with POS card you will not be able to form ring with just one fiber.
WHat you can do is if you do not need protection and have only one fiber for connectivity. Take WDM based single fiber solution means Transmit on one wavelength and receive on different so this way you have bidirectional communication without protection. Only thing whether such thing is available or not for the product you are looking at.
"can i use DPT line card as a normal pos interface '
You can use DPT card as POS if it is made like that such as
this card for 7600 is both DPT and POS
http://www.cisco.com/en/US/products/hw/routers/ps368/products_data_sheet09186a0080088774.html
one more which can be used by both DPT and POS
http://www.cisco.com/en/US/prod/collateral/modules/ps6267/product_data_sheet0900aecd803398df.html
But this one cannot be used for both as it is made only for DPT
http://www.cisco.com/en/US/prod/collateral/routers/ps167/product_data_sheet0900aecd8041add8.html

I bought I pod first generation but I can't use it cause need iOS 7 in my I pod first gen always said that need to up grade I bring already to I phone shope but always said sorry cause I pod first until iOS 5 only now need iOS 7

Pls help I have I pod first generation but I can't use it cause always saying that need to upgrade to iOS 7 but when I bring this to apple shoppe they said sooty I pos first generation up to 5ios only until now I can't use this I pod

You can use it as you did with the older Apps written that support iOS 5.x, nothing has changed there. However, if you want to run the newest apps and/or those that require a higher iOS version, bottom line is that you'll need to purchase a new iPad that will be capable of running that iOS and apps.
It wouldn't make any sense for Apple to allow iOS 7 to run on a 1st Gen iPad and have dismal performance. I certainly wouldn't be too happy about it. Hardware advances very rapidly...that's a fact of life if you're going to use any type of device that has a chip inside of it.

Can we use IF statement in PDF templates

Hi,
I developed a PDF template. I need to underline ang bold the records based on a specific condition. Can we use IF conditon in PDF templates. Please suggest.
Thanks...

Billy Verreynne wrote:
The case syntax is a bit funny though as there's not a single condition evaluation (like a DECODE or case structs from some other languages).
This is what I would expect a typical case struct to look like - evaluating a single condition:
case <condition>
when <value-1> then return <result-1>
when <value-n> then return <result-n>
else
return <return-z>
end
?:| You mean like this...?
SQL> ed
Wrote file afiedt.buf
1 select empno, ename, deptno
2        ,case deptno
3           when 10 then 'This is Department 10'
4           when 20 then 'And department 20'
5           when 30 then 'And of course department 30'
6         else
7           'Blimey it is something else!'
8         end as dept_desc
9* from emp
SQL> /
     EMPNO ENAME          DEPTNO DEPT_DESC
      7369 SMITH              20 And department 20
      7499 ALLEN              30 And of course department 30
      7521 WARD               30 And of course department 30
      7566 JONES              20 And department 20
      7654 MARTIN             30 And of course department 30
      7698 BLAKE              30 And of course department 30
      7782 CLARK              10 This is Department 10
      7788 SCOTT              20 And department 20
      7839 KING               10 This is Department 10
      7844 TURNER             30 And of course department 30
      7876 ADAMS              20 And department 20
      7900 JAMES              30 And of course department 30
      7902 FORD               20 And department 20
      7934 MILLER             10 This is Department 10
14 rows selected.

In alv report can i use control break events? if no .whay?

Hi all,
in alv report can i use control break events? if no .whay?

hi,
you can use control break statements in ALV report.
for example: if one PO is having more than one line item, that time you need to display PO only once.

HT1751 I need to uninstall and reinstall iTunes (it won't let me update). So, how do I copy or back up my iTunes library of over 1,500 songs? Can I use a Flash Drive to do so?

I need to uninstall and reinstall iTunes (it won't let me update). I have IE 8 on Windows XP, and iTunes 10 something. In my Program files list I see iTunes and iTunes (2) and even iPod and iPod (2) where a tech had to back up and do this for me before. I'm just trying to fix it all. I keep getting the "The feature you are trying to use is on a network resource that is unavailable. Click OK to try again, or enter an alternate path to a folder containing the installation package 'iTunes.msi' in the box below." I can even run a search and find the folder, but it gives me the same error message. I was planning on using the Microsoft Fix-It tool to help uninstall then Reinstall iTunes. But I need to backup my library. So, how do I copy or back up my iTunes library of over 1,500 songs? Can I copy the folder to desktop or can I use a Flash Drive to backup my music? I don't want to do anything until I know for sure how I can backup my songs, and then reinstall them into iTunes. Thanks for any help.

Ok, thanks that helps. I don't have an external hard drive though. What about backing up through 'the cloud'? I'm just wondering since my husband syncs his iPod to the PC through iTunes and he's worried that he will lose all the songs on his iPod if the library is lost from iTunes and he tries to 'sync' it up again. I'm not exactly sure how to 'copy the entire iTunes folder' either. I kinda suck at this unless I have step by step instructions, which I haven't found yet on iTunes help or other sources.
The only way I know how to back anything up is by going back to a restore point, etc. (as stated before, we don't have an external hard drive.)
Thanks for the info.

Can we use SPA-4XOC3-POS-V2 on 7600-SIP-400

Similar Messages

Maybe you are looking for