Can WLC 4402 support AIR-CAP1602E-S-K9?
Hi
I had 1 end of life WLC 4402 controller. Can it support AIR-CAP1602E-S-K9 access point? If cannot, what is the supported access points for WLC 4402.
Thanks
Hi Steve
Thanks for the reply. Another question if i use the below access point with smartnet and configure as standalone AP. But in future if I want to configure to lightweight AP, can i request the firmware from CISCO TAC to flash the AP and make it lightweight? Thanks
AIR-SAP1602E-S-K9
802.11a/g/n Standalone AP, Ext Ant, S Reg Domain
Similar Messages
-
Hi all,
I implemented "guest" wlan with web authentication (login+password with expiration). How can I protect these guests from being sniffed on the air. I speek about preventing "arp spoofing" and "man-in-the-midle". Shortly I want cause guests don't see each other on the air.
help meYou can confgure Layer 2 security with TKIP or AES which ensures Message Intergrity Check for the specified VLANs.On Controller specify it as WPA or WPA2
-
Hi everyone!
Question is simple, but I cannot find it in google.
Does WLC 5508 support AIR-LAP1042N?
Reagrds,
AlekseiOne more question.
What poe injector is supported on AIR-LAP1042N?
I have found poe injectors for other APs.
1.AIR-PWR-B=
2.AIR-PWRINJ4
Will anyone of these support this AP? -
AIR-CAP1602I-E-K9 Not Talking to WLC 5508
hi all,
can't seem to get my APs to talk to WLC 5508.
can someone advise which WLC firmware to use and where can i get/download (link pls).
currently WLC is running 6.0.199.4.
Mar 1 00:00:47.839: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inlin
e power source
*Mar 1 00:00:53.931: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:00:55.963: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 172.28.159.15, mask 255.255.255.192, hostname APfc99.47a3.4d22
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:06.899: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_f8
:72:64'running version 6.0.199.4 is rejected. <<<<
APfc99.47a3.4d22>sh ve
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFT
WARE (fc1)
APfc99.47a3.4d22 uptime is 11 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1726W6DQ
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: FC:99:47:A3:4D:22
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17182J4J
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1726W6DQ
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xFHi,
Date and time is ok on the WLC,
I configured Accept Self Signed Certificate (SSC) under Security / AP policy, once done the WLC recognized the AP, but output from the console of the AP power cycle the access point is:
IOS Bootloader - Starting system.
FLASH CHIP: Micronix MX25L256_35F
Xmodem file system is available.
flashfs[0]: 5 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 6551040
flashfs[0]: Bytes available: 25384960
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 4c:00:82:9a:47:a3
************* loopback_mode = 0
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"...####################
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x100000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Micronix MX25L256_35F
flashfs[2]: 5 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31808000
flashfs[2]: Bytes used: 6551040
flashfs[2]: Bytes available: 25256960
flashfs[2]: flashfs fsck took 9 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 1 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
memory validate-checksum 30
^
% Invalid input detected at '^' marker.
no ip http server
^
% Invalid input detected at '^' marker.
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
login authentication default
^
% Invalid input detected at '^' marker.
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Warning: the compile-time code checksum does not appear to be present.
cisco AIR-CAP1602I-N-K9 (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1730S57A
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 4C:00:82:9A:47:A3
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17284HL9
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1730S57A
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-N-K9
% Please define a domain-name first.
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:12.451: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:13.683: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:14.687: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 00:00:15.123: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
*Mar 1 00:00:15.151: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:15.151: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Mar 1 00:00:16.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to uplwapp_crypto_init: MIC Present and Parsed Successfully
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact pe
rformance
*Mar 1 00:00:48.695: %CDP_PD-4-POWER_OK: All radios disabled - INJECTOR_CONFIGU
RED_ON_SOURCE inline power source
*Mar 1 00:00:48.923: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 10.2.3.100, mask 255.255.255.0, hostname AP4c00.829a.47a3
Translating "CISCO-CAPWAP-CONTROLLER.campeche.ecosur.mx"...domain server (10.2.3
.10) [OK]
*Mar 1 00:00:59.915: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:00:59.919: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established. A0203E6, 147E, A020364, A47B, 0
*Mar 1 00:01:09.915: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:33:18.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:33:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
*Jan 29 09:34:17.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.
2.3.230:5246
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 29 09:34:17.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Jan 29 09:34:28.015: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:34:28.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:34:33.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
and debug command output enable CAPWAP events
(Cisco Controller) >debug capwap events enable
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.092: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:08.093: 4c:00:82:9a:47:a0 DTLS keys for Control Plane deleted successfully for AP 10.2.3.100
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 DTLS connection closed event receivedserver (10.2.3.230/5246) client (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 Entry exists for AP (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 No AP entry exist in temporary database for 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.104: apModel:
*spamApTask7: Jan 29 03:39:08.104: apType = 38 apModel:
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Received LWAPP DISCOVERY REQUEST to 6c:41:6a:5f:95:2f on port '13'
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:18.104: 4c:00:82:9a:47:a3 DTLS connection not found, creating new connection for 10:2:3:100 (42107) 10:2:3:230 (5246)
*spamApTask7: Jan 29 03:39:18.638: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Allocated index from main list, Index: 397
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Using CipherSuite AES128-SHA
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS keys for Control Plane are plumbed successfully for AP 10.2.3.100. Index 398
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS Session established server (10.2.3.230:5246), client (10.2.3.100:42107)
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Starting wait join timer for AP: 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a0 Join Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a3 Deleting AP entry 10.2.3.100:42107 from temporary database.
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 MIC AP is not allowed to join by config
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 Join Request failed! -
AIR-CAP1602i cannot join a WLC 5508 controller
Hello,
I'm managing a large number of access points on a Cisco wlc 5508 controller.
We've recently purchased a bunch of new AIR-CAP1602I-E-K9.
note that we already have AIR-CAP1602I-E-K9 and other models in production.
These A.P are not able to join the controller for some reason, I've tried a lot of different things but I am now at a loss.
I have checked the regulatory domain, upgraded the FUS, manually upgraded the software version of the LAP to match the version on the other A.P.
I even downgraded/upgraded the WLC code (version 7.4.x and 8.0)
I use the dhcp option 43 to to send the controller IP.
Here are the info that can help:
errors:
#on A.P
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
#on WLC
Lwapp join request rejected (WLC version 7.6.130.0)
Failed to add database entry (WLC version 8.0)
WLC sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... XXX
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... XXX
Last Reset....................................... Software reset
System Up Time................................... 6 days 4 hrs 16 mins 27 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... Multiple Countries:CA,FR
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +41 C
External Temperature............................. +22 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 7
Number of Active Clients......................... 1977
Burned-in MAC Address............................ A4:93:4C:B0:E4:C0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 250
AP sh version
AP58f3.9cb8.3701#sh version
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(4)JB6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:56 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP58f3.9cb8.3701 uptime is 31 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-4.JB6/ap1g2-k9w8-mx.152-4.JB6"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 229366K/32768K bytes of memory.
Processor board ID FGL1832X5QU
PowerPC CPU at 533MHz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.6.100.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 58:F3:9C:B8:37:01
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC183171L4
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1832X5QU
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
AP sh inventory
NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP1602I-E-K9 , VID: V01, SN: FGL1832X5QU
Thanks for your help !Hi Olivier,
The error messages that you have on the debugs:
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
It is related to the bug: CSCuh46442
https://tools.cisco.com/bugsearch/bug/CSCuh46442/?referring_site=ss
This bug is resolved in version : 8.0.100.0
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn80.html#pgfId-1163951
Can you please paste here "show ap auth-list" from the controller CLI?
I suggest to enable MIC if it is not enabled, and then check if the AP's will join or not.
Kind Regards
Mohammad Setan -
01#Aironet 1600 (AIR-CAP1602i) & 3850 WLC (WS-C3850-24T-L)
Hi Friends
Trying to join 1602i (AIR-CAP1602i-E-k9) to 3850 (WS-C3850-24T) WLC but after join to WLC, the access point keeps rebooting
3850# Sho Version
Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIV
ERSALK9-M), Version 03.03.03SE RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Sun 27-Apr-14 18:33 by prod_rel_team
Cisco IOS-XE software, Copyright (c) 2005-2014 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0.
(http://www.gnu.org/licenses/gpl-2.0.html) For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: C3850 Boot Loader (C3850-HBOOT-M) Version 1.1, RELEASE SOFTWARE (P)
Ctrl1 uptime is 59 minutes
Uptime for this control processor is 1 hour, 1 minute
System returned to ROM by reload
System image file is "flash:packages.conf"
Last reload reason: reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: Ipbase
License Type: Permanent
Next reload license Level: Ipbase
cisco WS-C3850-24T (MIPS) processor with 4194304K bytes of physical memory.
Processor board ID FOC1729V00P
1 Virtual Ethernet interface
28 Gigabit Ethernet interfaces
4 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
250456K bytes of Crash Files at crashinfo:.
1609272K bytes of Flash at flash:.
0K bytes of Dummy USB Flash at usbflash0:.
0K bytes of at webui:.
Base Ethernet MAC Address : d0:c7:89:74:ef:00
Motherboard Assembly Number : 73-12238-06
Motherboard Serial Number : FOC17283XTY
Model Revision Number : B0
Motherboard Revision Number : D0
Model Number : WS-C3850-24T
System Serial Number : FOC1729V00P
Switch Ports Model SW Version SW Image Mode
* 1 32 WS-C3850-24T 03.03.03SE cat3k_caa-universalk9 INSTALL
Configuration register is 0x102
3850#show wireless mobility summary
Mobility Controller Summary:
Mobility Role : Mobility Controller
Mobility Protocol Port : 16666
Mobility Group Name : default
Mobility Oracle IP Address : 0.0.0.0
DTLS Mode : Enabled
Mobility Domain ID for 802.11r : 0xac34
Mobility Keepalive Interval : 10
Mobility Keepalive Count : 3
Mobility Control Message DSCP Value : 48
Mobility Domain Member Count : 1
Link Status is Control Link Status : Data Link Status
Controllers configured in the Mobility Domain:
IP Public IP Group Name Multicast IP Link Status
192.168.188.22 - default 0.0.0.0 UP : UP
3850#show wireless country configured
Configured Country.............................: AU - Australia
Configured Country Codes
AU - Australia : 802.11a Indoor,Outdoor/ 802.11b / 802.11g
1602i#show version
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(4)JB5h, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 16-Apr-14 00:32 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFT
WARE (fc1)
APc067.af86.55a3 uptime is 7 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-4.JB5h/ap1g2-k9w8-mx.152-4.JB5h"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 229366K/32768K by
tes of memory.
Processor board ID FGL1739W06Y
PowerPC CPU at 533MHz, revision number 0x2151
Last reset from power-on
LWAPP image version 10.1.130.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C0:67:AF:86:55:A3
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17374QRS
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1739W06Y
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xF
3850# Show logging
Ctrl1#
*Jun 14 05:37:44.747: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:37:44.750: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:37:50.040: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:37:50.042: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:05.467: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:05.470: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:10.760: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:10.762: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:26.672: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:26.675: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:31.968: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:31.970: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:47.388: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:47.390: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:52.680: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:52.682: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:39:08.100: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:39:08.102: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:39:13.396: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:39:13.398: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:39:29.024: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:39:29.026: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:39:34.320: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:39:34.322: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:39:46.377: *%DTLS-3-HANDSHAKE_FAILURE: 1 wcm: Failed to complete DTL
S handshake with peer 192.168.188.25 for AP 0000.0000.0000Reason: sslv3 alert u
nexpected message
1602i# Show Logging
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:01.591: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:01:01.591: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Mar 1 00:01:02.011: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:02.247: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:08.315: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init:
MIC Present and Parsed Successfully
*Mar 1 00:01:09.075: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r
eset
*Mar 1 00:01:09.075: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to r
eset
*Mar 1 00:01:18.755: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:01:29.255: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:29.255: APAVC: Registering with CFT
APAVC: CFT registration of delete callback succeeded
APAVC: Reattaching Original Buffer pool for system use
Pool-ReAtach: paks 9355 radio8747
*Mar 1 00:01:36.415: %CDP_PD-4-POWER_OK: Full power - INJECTOR_CONFIGURED_ON_SO
URCE inline power source
*Mar 1 00:01:37.487: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:38.487: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to up
*Mar 1 00:01:38.543: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:39.206: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 14 05:47:22.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:22.335: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to up
*Jun 14 05:47:24.287: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:24.287: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:29.287: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:29.291: %DTLS-5-ALERT: Received WARNING : Close notify alert from
192.168.188.22
*Jun 14 05:47:29.291: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.188.22:5246
*Jun 14 05:47:29.291: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 14 05:47:22.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:22.291: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:22.291: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:27.291: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:27.295: %DTLS-5-ALERT: Received WARNING : Close notify alert from
192.168.188.22
*Jun 14 05:47:27.295: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.188.22:5246
*Jun 14 05:47:27.347: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Jun 14 05:47:27.375: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to a
dministratively down
*Jun 14 05:47:27.375: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to a
dministratively down
*Jun 14 05:47:27.379: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 14 05:47:27.431: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 14 05:47:28.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
*Jun 14 05:47:28.423: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to do
wn
*Jun 14 05:47:28.431: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to r
eset
*Jun 14 05:47:29.415: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to up
*Jun 14 05:47:29.423: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to down
*Jun 14 05:47:29.467: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 14 05:47:29.475: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to do
wn
*Jun 14 05:47:29.483: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r
eset
*Jun 14 05:47:30.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to up
*Jun 14 05:47:30.475: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
*Jun 14 05:47:30.519: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 14 05:47:31.519: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to up
*Jun 14 05:47:37.431: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 14 05:47:44.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:44.287: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:44.287: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:49.287: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:49.291: %DTLS-5-ALERT: Received WARNING : Close notify alert from
192.168.188.22
*Jun 14 05:47:49.291: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.188.22:5246Hi Leo
For product AIR-CAP1602I-E-K9 what country have to configured?
flowed this table: -
Cisco AIR-LAP1041N-E-K9 not working with WLC 4402 version 7.0.116.0
Hi All,
appreciate your support for a problem i started facing today. i have a Cisco WLC 4402 running version 7.0.116.0 and it is working great with 25 Cisco 1252 APs. we have recieved a new 20 Cisco 1041N APs today and i installed one in our site but it doesn't work. it worked fine and loaded the image from flash and got the WLC ip address through DHCP option and started showing the below error:
*Mar 1 00:00:10.021: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:10.033: *** CRASH_LOG = YES
*Mar 1 00:00:10.333: Port 1 is not presentSecurity Core found.
Base Ethernet MAC address: C8:9C:1D:53:57:5E
*Mar 1 00:00:11.373: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:11.465: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1088 messages)
*Mar 1 00:00:11.494: status of voice_diag_test from WLC is false
*Mar 1 00:00:12.526: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.594: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.647: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 12:50 by prod_rel_team
*Mar 1 00:00:13.647: %SNMP-5-COLDSTART: SNMP agent on host APc89c.1d53.575e is undergoing a cold start
*Mar 1 00:08:59.062: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:08:59.062: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:08:59.138: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:08:59.837: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:09:00.145: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:09:09.136: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.16.26.81, mask 255.255.255.0, hostname APc89c.1d53.575e
*Mar 1 00:09:17.912: %PARSER-4-BADCFG: Unexpected end of configuration file.
*Mar 1 00:09:17.912: status of voice_diag_test from WLC is false
*Mar 1 00:09:17.984: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:09:19.865: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:09:19.886: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:09:20.873: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:09:20.874: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
Translating "CISCO-CAPWAP-CONTROLLER.atheertele.com"...domain server (172.16.40.240)
*Mar 1 00:09:29.029: %CAPWAP-5-DHCP_OPTION_43: Controller address 172.16.100.102 obtained through DHCP
*May 25 08:27:02.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:02.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:03.175: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:03.177: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:03.177: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:03.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:03.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:03.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:03.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:03.378: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:03.448: status of voice_diag_test from WLC is false
*May 25 08:27:14.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:14.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:15.185: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:15.186: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:15.186: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:15.330: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:15.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:15.334: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:15.334: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:15.379: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:15.450: status of voice_diag_test from WLC is false
*May 25 08:27:26.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:26.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:27.182: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:27.183: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:27.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:27.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:27.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:27.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:27.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:27.377: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:27.433: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*May 25 08:27:27.446: %PARSER-4-BADCFG: Unexpected end of configuration file.
*May 25 08:27:27.447: status of voice_diag_test from WLC is false
*May 25 08:27:27.448: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*May 25 08:27:27.456: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*May 25 08:27:38.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:38.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:39.183: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:39.184: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:39.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:39.326: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:39.329: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:39.329: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:39.330: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:39.375: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:39.446: status of voice_diag_test from WLC is false
*May 25 08:27:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:49.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:50.179: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:50.180: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:50.180: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:50.323: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:50.326: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:50.326: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:50.326: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:50.370: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:50.425: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*May 25 08:27:50.438: %PARSER-4-BADCFG: Unexpected end of configuration file.
i searched for the regulatory domains difference between AIR-LAP1041N-E-K9 and AIR-LAP1041N-A-K9 and didn't find any difference that may affect the operation of this AP.
just to mention that our configuration in WLC for regulatory domains is:
Configured Country Code(s) AR
Regulatory Domain 802.11a: -A
802.11bg: -A
My question is, should i only include my country in the WLC (IQ) to add the requlatry domain (-E) to solve this problem? or changing the country will affect the operation of all working APs??
Appreciate your kind support,
Wisam Q.Hi Ramon,
thank you for the reply but as shown in the below link:
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7.0.html#wp233793
the WLC in version 7.0.116.0 supports Cisco 1040 seiries APs.
Thanks,
Wisam Q. -
Problem Joining AIR-CAP1602I-C-K9 with WLC 5508
Hi,
I am having trouble to get AIR CAP1602I-C-K9 attached to a 5508 WLC running code 7.4.110.0
Here is what I got from the AP logs:
====================================================================================================
Extracting files...
ap1g2-k9w8-mx.152-2.JB2/ (directory) 0 (bytes)
extracting ap1g2-k9w8-mx.152-2.JB2/K5.bin (75790 bytes)!!!!
*Dec 6 15:09:23.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 6 15:09:23.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.10.100 peer_port: 5246
*Dec 6 15:09:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.10.100
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: CAPWAP!
extracting ap1g2-k9w8-mx.152-2.JB2/ap1g2-k9w8-mx.152-2.JB2 (9202946 bytes)!!!!!!!!! SM handler: Failed to process message type 10 state 5.
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 172.16.10.100perform archive download capwap:/ap1g2 tar file
*Dec 6 15:09:23.583: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.
*Dec 6 15:09:23.587: Loading file /ap1g2...
*Dec 6 15:09:24.007: %LINEPROTO-5-UPDOWN:!!!!!!!!!!! Line protocol on Interface Dot11Radio0, changed state to down
*Dec 6 15:09:24.063: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up!!!!!!!!!!!
*Dec 6 15:09:25.139: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up!!!!!!!!!!
*Dec 6 15:09:26.135: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Premature end of tar file
ERROR: Problem extracting files from archive.
Download image failed, notify controller!!! From:7.4.1.37 to 7.4.110.0, FailureCode:3
archive download: takes 63 seconds
*Dec 6 15:10:26.851: capwap_image_proc: problem extracting tar file
====================================================================================
after that the AP reboots and do same process over and over again,
Please help..
Many Thanks,
BarthHere is the info about AP and WLC:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... WLC1-AP
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 172.16.10.100
Last Reset....................................... Power on reset
System Up Time................................... 0 days 4 hrs 12 mins 28 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +44 C
External Temperature............................. +28 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ F8:72:EA:EF:2E:A0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, Power Off, Fan On
Maximum number of APs supported.................. 100
AP4403.a7fd.f040#sh ver
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:45 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP4403.a7fd.f040 uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-2.JB/ap1g2-k9w8-mx.152-2.JB"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-C-K9 (PowerPC) processor (revision B0) with 98294K/32768K bytes of memory.
Processor board ID FGL1711ZJNW
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:03:A7:FD:F0:40
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC16517DZ1
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1711ZJNW
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-C-K9
Configuration register is 0xF
AP4403.a7fd.f040#sh inventory
NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP1602I-C-K9 , VID: V01, SN: FGL1711ZJNW -
Can I configure Cisco 1602i (AIR-CAP1602I-T-K9) in Standalone mode ?
Hi everybody, please, i need some help here.
I bought 3 Cisco 1602i (AIR-CAP1602I-T-K9) but I didn't bought a Controller. How can I configure then in Standalone mode ?
I Saw in other forums, i need to change the IOS Software to an Autonomous Software. They suggested the ap1g2-k9w7-tar.152-4.JA1.tar. I would like to know if it is the right software and if there is any problem with licensing if i download and use it.
Explanation of the differences between AIR-CAP-1602i-x-K9 e AIR-SAP-1602i-x-K9
http://community.spiceworks.com/topic/448208-cisco-aironet-1602i-questions-issues
How to convert to IOS autonomous
http://www.experts-exchange.com/Networking/Wireless/Q_28245190.html
IOS Download:
http://software.cisco.com/download/release.html?mdfid=284366503&softwareid=280775090&release=15.2.4-JA1&flowid=37523
Thanks.
WesleyHi,
Yes you must need to change to autonomous mode.Yes it is the right software and you will not face any problem regarding license.
But for download the autonomous AP image from cisco you need a CCO (Cisco login) and valid service contract .
Here is the latest image:Can download from here
http://software.cisco.com/download/release.html?mdfid=284366503&flowid=37523&softwareid=284180979&release=15.2.4-JB5&relind=AVAILABLE&rellifecycle=ED&reltype=latest
How to covert from lAP to autonomous :
http://www.youtube.com/watch?v=QQ_NuxdRhQ4
http://rscciew.wordpress.com/2014/05/07/access-point-conversion-lap-to-aap-and-vice-versa/
Regards
Dont forget to rate helpful posts -
Hello all,
I've got a following problem with bringing up simple wireless configuration. There is a WLC-4402 controller and several remote locations (I am testing one so far). Two WLAN configured (one for employee and the other for guest access - no mobility anchoring used, guest is just mapper to VLAN restricted on the firewall). WLC serves DHCP pools for wireless clients. Problem I am experiencing at the moment is that user with laptop is able to connect to guest WLAN, got an IP but can communicate (ping) only its own IP, the controller IP in guest subnet and default gateway (which is the firewall interface). Traffic to any other destinations never hit gateway (I am running tcpdump on it to confirm). I double checked controller config but no luck so far. Could that be caused by missconfigured tunnel? No ACL or restriction set on WLC - see attached config.
Thank you in advance,
PeterIs this an open network or have you enabled layer 3 security? Web Auth? I can see you have created a lobby admin account so expect that you use this for guest account creation with web auth..
When you associate/receieve IP address to the open guest network have you then opened a web browser and authenticated? Until you enter your login details created on the WLC I would imagine that you wouldn't be able to send any data.
If you have authenticated already, can you check on the WLC that the client is associated/authenticated and is the Corp network ok? Also what is the topology between the WLC/Firewall/Remote sites.
Cheers
Mat -
Although it is demand, or can not support ogg? In it to support Flash IDE, you can not play in AIR SDK.
Looking at this page as an example:
mp3licensing.com - Royalty Rates
the information seems to be six years old. I haven't heard about anyone being sued for not registering their app. I'll ask Adobe for an opinion on this. -
Can AIR-CAP1602i-x-k9 be converted to stand alone??
can air-cap1602i-x-k9 be converted to stand alone??
Yes , you can convert the AP to stanadlone by pushig the below image into the AP
http://software.cisco.com/download/release.html?mdfid=284366503&flowid=37523&softwareid=284180979&release=15.2.4-JB3a&relind=AVAILABLE&rellifecycle=ED&reltype=latest
You can use the below method to convert the same
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release
using a TFTP server: This method is for local conversion.
Step 1 The PC on which your TFTP server software runs must be configured with a static IP address in the range
of 10.0.0.2 to 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a
1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200
series access point.
Step 4 Connect the PC to the access point using a Category 5 or better Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold the MODE button while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), and release the
MODE button.
Step 8 Wait until the access point reboots as indicated by all LEDs turning green followed by the Status LED
blinking green.
Thanks.. -
Cisco AIR-CAP1602I-E-K9 Telnet issue
Hi Team, I have installed new cisco AIR-CAP1602I-E-K9 in the remote site LAN however the access point received the ip address through central DHCP helper address. I am able to ping the access point through LAN but I am unable to telenet the device to configure.
Also when Field enginner visited on site to connect physical he connected through console but we were not able get into configure mode though we had full privilege access.
Please advice.
AP0006.f618.26f5#sh version
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP0006.f618.26f5 uptime is 3 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FGL1703ZA3E
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:06:F6:18:26:F5
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC164971SY
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1703ZA3E
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xFThanks,
1. Does it mean I should not be able to telnet also into the AP though I can ping from Router LAN ( AP is connected directly to router ethernet interface).
2. I am also not able to discover controller when running in controller-based IOS. getting below errors.
Thanks to advice on above points.
Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
AP0006.f618.26f5#
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.1
AP0006.f618.26f5#1.13
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:24.029: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:24.029: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:24.029: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
Not in Bound state.
*Mar 1 00:03:49.505: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:53.393: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:03:53.477: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.93.22, mask 255.255.255.128, hostname AP0006.f618.26f5
en
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.50.1.235) (10.50.1.236)
*Mar 1 00:04:00.505: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:04:00.565: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
Not in Bound state.
*Mar 1 00:04:46.069: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:04:49.161: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:04:49.273: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.115.20, mask 255.255.255.128, hostname AP0006.f618.26f5
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.50.1.235)
*Mar 1 00:04:57.069: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP. (10.50.1.236)
*Mar 1 00:05:15.068: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
Not in Bound state.
*Mar 1 00:06:00.568: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:06:04.396: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:06:04.412: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.93.22, mask 255.255.255.128, hostname AP0006.f618.26f5
en
AP0006.f618.26f5#
AP0006.f618.26f5#sh
Writing out the event log to flash:/event.log ...
ip int
*Mar 1 00:06:11.668: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: Could not discover WLC using DHCP IP address, Reload to use static IP. -
IMP: Cisco AIR-CAP1602 &1532 not joining 2504 Controller issue
Dear Team, We have Cisco wireless implementation in clients premises. We have 8 indoor AP (AIR-CAP1602E-AK9) and 2 Outdoor AP (AIR-CAP1532I-AK9) . Seven indoor APs are able to join the 2504 controller, but 1 indoor AIR-CAP1602E AP is not joining and signal is RED continuously while as outdoor AP AIR-CAP1532I-AK9 signal goes blinking from green, red to amber continuously and is not downloading LWAPP image from the controller even after hard reset.
The output for both APs shown below-
1) AIR-CAP1602E-A-K9:
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvara
ap: reset
Are you sure you want to reset the system (y/n)?y
System resetting...
Boot from flash
IOS Bootloader - Starting system.
FLASH CHIP: Spansion S25FL256
Xmodem file system is available.
flashfs[0]: 14 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 418304
flashfs[0]: Bytes available: 31517696
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 18:e7:28:d1:9b:05
************* loopback_mode = 0
The system is unable to boot automatically because there
are no bootable files.
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvarag
Same event repeating, failed to reset and reboot device
2) AIR_CAP1532I-A-K9 (Outdoor AP):
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_47:32:e4'running version 7.5.102.0 is rejected.
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 100.1.1.20
signal goes blinking from Grean, Red to Amber continuously.
Failed to download LWAPP image from the controller even after hard reset.
Default image: 7.6.95.12
Logs and screen shot attached
Please advice.
Thanks
AakashHi please note the details below-
AIR-CAP1602E-A-K9:
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvara
ap: reset
Are you sure you want to reset the system (y/n)?y
System resetting...
Boot from flash
IOS Bootloader - Starting system.
FLASH CHIP: Spansion S25FL256
Xmodem file system is available.
flashfs[0]: 14 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 418304
flashfs[0]: Bytes available: 31517696
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 18:e7:28:d1:9b:05
************* loopback_mode = 0
The system is unable to boot automatically because there
is no bootable files.
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvarag
Can't reboot device!
WLC-SYSLOG
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.5.102.0
Bootloader Version............................... 1.0.18
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_47:32:e4
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 100.1.1.20
Last Reset....................................... Power on reset
System Up Time................................... 0 days 2 hrs 18 mins 39 secs
System Timezone Location......................... (GMT -6:00) Central Time (US a nd Canada)
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +32 C
External Temperature............................. +37 C
Fan Status....................................... 4000 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
Number of Active Clients......................... 0
Burned-in MAC Address............................ 24:E9:B3:47:32:E0
Maximum number of APs supported.................. 15 -
Hellp on Nokia E61i associating with Cisco WLC 4402
I met some problem with associate Nokia's dual mode mobile phone E61i with Cisco WLC 4402, hope someone can help me on it:
I setup a VOICE WLAN in 4402(v5.0.148), Layer2 security is WPA1+WPA2, Key management using 802.1x, WPA1 policy enable both TKIP and AES, Radius server using ACS engine(v4.1.1.23)(enable PEAP-MSCHAPv2);
I can use my laptop to join this WLAN(my laptop configure with PEAP/MSCHAPv2, WPA-TKIP, not validate server certificate), but can't let E61i join it, each time it will remind me âunable to connect, WPA authenticate failed).
In E61i, I select WPA/WPA2 as WLAN security mode, enable EAP-PEAP, under EAP-PEAP, I enable EAP-MSCHAPv2; however under Cipher, there's a lot of options such as âRSA,3EDS,SHAâ, âRSA,AES,SHAâ, but there's no TKIP, I have tried to enable all of them and tried only enable those items which include AES, but I failed each time with the same reminder âunable to connect, WPA authenticate failedâ. I checked ACS's failed log, there's no record; In 4402, there also have no record.
If I change the security to open or static WEP for VOICE WLAN, then the E61i can connect to the WLAN.
I think the problem maybe relate to encryption or certificate, right now I just do the test in lab, not in customer's real environment, so I use ACS to generate a self signed certificate and installed it in ACS.
Pls. help to point me what I need to adjust to make it work. Thanks!Hello,
CCKM Key Management mode on Nokia E61i phone can be used
against Cisco LWAPP AP's with TKIP encryption
Nokia E61i (and other E-series WLAN enabled phones) are supporting CCKM key management method with both dynamic WEP and TKIP ciphers.
On the phone configuration, 802.1X security mode needs to be in use in order to enable CCKM support. WPA/WPA2 security mode on the phone is dedicated to standards based WPA and WPA2 methods and it does not allow usage of proprietary CCKM key management method.
Phone's 802.1X security mode does not mean that phone would only support dynamic WEP encryption method in this mode although in contexts term "802.1X" may be attached to pure dynamic WEP (legacy / pre WPA era)security methods.
 802.1X security mode can be seen on Nokia Eseries phones as sort of an "everything with EAP based authentication is allowed" mode, meaning that following key management and cipher configurations are supported:
- WPA-Enterprise = WPA Key Management (EAP based authentication) with TKIP encryption
- WPA2-Enterprise = WPA2 Key Management (EAP based authentication) with AES encryption
- Mixed WPA/WPA2-Enterprise = I.e. WPA/WPA2 Mode Migration WPA2 Key Management (EAP based authentication) with AES (for unicast data) and TKIP (for multicast data) ciphers
- 802.1X dynamic WEP = legacy (pre-WPA era) 802.1XÂ based dynamic WEP (EAP based authentication with dynamic WEP encryption)
Supported:
- CCKM with WEP = CCKM Key Management (EAP based authentication) with dynamic WEP encryption
- CCKM with TKIP = CCKM Key Management (EAP based authentication) with TKIP encryption
Not supported:
- CCKM with AES = CCKM Key Management (EAP based authentication) with AES encryption
Please note that CCKM-AES mode (CCKM Key Management with AES cipher) is not working properly due to some incompatibilities between Cisco and Nokia implementations thus it must not be listed as a supported combination on the current Nokia E-series devices. We are also seeing CCKM-Fast
Re-authentication failures with Cisco autonomous AP's when AES encryption is used although initial authentication to autonomous AP's is successful. Nokia is currently working with Cisco to get CCKM-AES based authentications and roaming working properly with both LWAPP and autonomous Cisco AP's.
 Also note that Nokia E-Series does not support Cisco proprietary CKIP/CMIC encryption/data integrity methods. CKIP/CMIC is supported at least by Cisco autonomous AP's and it seems to be available also
at least on LWAPP AP version 4.1.171.0.
 CCKM on E-Series devices has been tested against Cisco LWAPP (ver. 4.1.171.0) and it works when TKIP encryption is in use (WPA Policy + TKIP encryption in Cisco LWAPP configuration terms).
In practice this means Cisco LWAPP is configured in a following manner: WLAN -> Edit -> Security->Â
Layer 2 Security = WPA+WPA2
WPA+WPA2 Parameters:
-WPA Policy = enabled
-WPA Encryption = TKIP enabled, AES disabled
-WPA2 policy = disabled
-Auth.Key Mgmt = CCKM
Br,
-Pasi-
Maybe you are looking for
-
Question on Electronic bank statement
HI, i am working on SWIFT MT 940 for uploading the EBS for customers. and want to use only SAP standard no customization (user exits) what are the details the bank statement should contain inorder to do posting to bank and clear the document of F110.
-
Why does my iPad show no sim when turning on cellular data?
Why does my iPad show no sim when turning on cellular data?
-
Hi guys. I have recently upgraded to itunes 6, installed it and quicktime 7.0.3. When i try and run itunes the following error message occurs: "Quicktime version 7.0.2 is installed, Itunes requires Quicktime 7.0.3 or later. Please re-install Itunes."
-
Update of latest ios taking a long time
I have the first ipad and am doing the update to the latest ios version through a PC. I am trying to install the download; however, it is taking a long time (more than an hour) and seems to be stuck on the backing up stage. I'm afraid to stop it be
-
Dust Inside my MBP screen? How can I remove it?
So I noticed some dust or debris inside my screen when I was cleaning it out! I'm never in very dusty rooms and the annoying part is that it's very obvious! How can I remove it (if any way)? Should I take it to Apple? It's only been just over a year