Can WLC2504 manage AP in remote networks?

Hi all,
I've just got a technical question. I'm just wondering if it could be possible to use WLC2504 to manage AP that are on a remote networks, ie they are behind a WAN link and behind a router. Let me explain myself bettter. This is what I'm trying to achive; in the Head Office I'm thinking of installing the WLC2504 to manage 5-locally-installed AP (with its appropriate Guest VLAN and Corp VLAN), then on the other two branches install another 5 APs respectively (with same schema Guest VLAN and Corp VLAN, needeles to say with different IPs).
Obviously, all 3 sites are connected using a WAN private network (all networks are routable) so my question is; could the APs installed on the remote branches talk to the WLC installed at the HO and register to grab their configuration? From what I've seen in all documentation is that WCL2504 can only talk to APs installed whithin same premises, ie only inter VLAN traffic and not traversing WAN links/routers.
Any help would be really appreciated.
Cheers

Hi Leo,
Thank you so much for your quick reply!
One last question. Do you know if WCL 2504 supports FlexConnect for AP1602I? I've found contradictory information.
This one says it does support FlexConnect for 1602I (when using WLC 5500)
http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/112042-technote-product-00.html
The link you posted doesn't mention AP 1600s to be supported
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-2/configuration/guide/cg/cg_flexconnect.html
And the datasheet for AP1600s doesn't especifillay say that FlexConnect is supported.
http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1600-series/data_sheet_c78-715702.html
http://www.cisco.com/c/en/us/td/docs/wireless/technology/apdeploy/Cisco_Aironet.html
http://www.cisco.com/c/en/us/td/docs/wireless/access_point/1600/quick/guide/ap1600getstart.html#wp37338
So my question is...can I use FlexConnect with WLC2504 and Aironet AP1602I?
Thanks in advance

Similar Messages

The partner transaction manager has disabled its support for remote/network transactions....When inserting during trigger in linked server

Hi All,
I am getting below error while inserting into Linked Server (sql2012) thru trigger from sql2008 ....However if i insert the same thru Store Procedure it is inserting successfully....MSDTC service is started on both sql server machines....also both machines
rebooted....but still i am facing this error.
OLE DB provider "SQLNCLI" for linked server "XXX.XXX.XXX.XX" returned message "The partner transaction manager has disabled its support for remote/network transactions.".
Msg 7391, Level 16, State 2, Procedure ins_test, Line 11
The operation could not be performed because OLE DB provider "SQLNCLI" for linked server "XXX.XXX.XXX.XX" was unable to begin a distributed transaction.
Could assist to resolve.
Regards
Shehzad

Hi SHzKhan,
According to your error message, we need to verify if you configure the MSDTC correctly, When you have more than one SQL Server involved in a Distributed Transaction, you need to make some changes to the default configuration of MSDTC for these distributed
transactions to succeed. There is a detail about recommending MSDTC settings for using Distributed Transactions in SQL Server, you can review the following article.
http://support.microsoft.com/kb/2027550/en-us
There is a similar issue about error 7391, you can refer to the following link.
http://dba.stackexchange.com/questions/30235/msg-7391-distributed-transactions-dtc-on-sql-server
Regards,
Sofiya Li
Sofiya Li
TechNet Community Support

Can I manage my parents MB from my computer using ARD. Even though they are on different networks

Can I manage my parents MB from my computer using ARD. Even though they are on different networks?>

When you say a diffrent network, do you mean accessing the computer over the internet?
VNC is built into the computer, so you don't need ARD to remote into a computer. To access your parents computer over the internet will most likely require configuring their router/firewall. And unless they're paying for a static ip, you'll also need some way to track their computer.
OR
you can use logmein, or teamviewer. Both programs are desgined to access a computer over the internet. Most of the time they don't require re-configuring the firewall.

Can I enable "Use default gateway on remote network" on VPN connection using Group Policy?

Hi,
First timer here so please bear with me!
Environment: Domain Windows 2003, Clients: Windows 7 and Windows XP (with Client Side Extensions pushed out)
When creating a VPN connection on a client machine manually with default settings the "Use default gateway on remote network" found in [Connection Properties - Networking - IPv4 - Advanced] is enabled, which is good as we don't allow split-tunneling.
I have a test GPO that creates a new VPN Connection [Computer Config - Preferences - Control Panel - Network Options], but the above setting is unticked.
Am I missing something on the options for the GP preference to set this automtically?
I can write a script to directly change the C:\Users\All Users\Microsoft\Network\Connections\Pbk\rasphone.pbk file but would prefer if I could sort it all out using Group Policy.
Any help would be greatly appreciated!
Thanks a lot!
David

Shane,
There is actually a way to set the "Use default gateway on remote network" through Group Policy Preferences. And this may even be a better way to do it, because you may change this flag without touching any other settings, or other VPN connections.
(All VPN connections are stored in the same .pbk file.)
Here's the trick: Opening the .pbk file in notepad, I realized that this is actually an oldstyle ini-structured file. And Group Policy Preferences can update ini files! In the .pbk file the section names are the VPN connections names, like [My VPN],
and the property IpPrioritizeRemote is the flag "Use default gateway on remote network".
So, in Group Policy Management Editor, go to Preferences / Windows Settings / Ini Files.
Create a new object with Action = Update, and File Path =
C:\ProgramData\Microsoft\Network\Connections\pbk\rasphone.pbk
(If this is where your file is located, I guess it is in c:\users if the VPN connection is made for a single user.)
Section Name should be the display name of your VPN connection, without the brackets.
Property Name = IpPrioritizeRemote
Property Value = 1
Peter, www.skov.com, Denmark
Peter :-)
This is great, but just one question. I also want to append a list of DNS Sufixes in order (when viewing a VPN properties, this is buried in
"Networking --> IPv4/6 --> Advanced --> DNS --> Append these DNS Suffixes (in order)". However, for the VPNs I have manually created with this list populated, I can't see any entries in the rasphone.pbk. Does anyone know
where these are stored?
Cheers.

How to manage dell-2816 switch from remote network..?

Hi,
According to below diagram how can i manage the dell-2816 switch from other network. It has management ip only worked on default vlan and default vlan is not editable also not routed ,we can only access the switch to connect laptop directly to switch port and if the port has default-vlan id-1 .
switch to switch trunk doing problem but when using the pvid as a access vlan ID then trunk is working between dell to juniper hope so cisco also work. But the major issue is remote manageability and also snmp , If switch does not getting ping from remotely then how the snmp will work ..?
Thanks
Mamdud
<ADMIN NOTE: Email id removed per privacy policy>

You would need a layer 3 device on the network that would route between the different networks/VLANs. Without a device performing VLAN routing, your only other option is to be on the VLAN 1 network.
If you have a client with dual nic ports, you may be able to assign 1 port the VLAN 1 network. The other port would be on the network with the rest of the devices.

Cisco ASA 5505 - EasyVPN - ARD can't scan remote Networks

Hi all,
We have been installing Cisco ASA5505 to hook our systems and remote offices together. Our first install went great, and I can scan the remote network no problem, this network is setup using the site to site VPN setup.
Since then we have added 3 more ASA5505 so the the mix, these are not running via the Site to Site VPN but are rather using the EZVPN.
On the Remote ASAs using EasyVPN, I cannot scan the networks with ARD or even Ping.
I am wondering if anyone has any insights on this? I know this info is a bit sketchy...
I will post more as I get it.

ASAs are the default gw for respective LANs. For the point 2 if i trace the packets i can see that their are blocked
packet-tracer input inside-g tcp 192.168.1.42 80 192.168.2.31 80
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.2.0 255.255.255.0 outside
Phase: 2
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
nat (inside-g,outside) source static obj-LAN-G obj-LAN-G destination static obj-LAN-BO obj-LAN-BO no-proxy-arp route-lookup
Additional Information:
NAT divert to egress interface outside
Untranslate 192.168.2.31/80 to 192.168.2.31/80
Phase: 3
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: inside-g
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
192.168.1.42 is the ASA1 inside IP address. But i've an explicit ACL that permits ALL traffic from 192.168.1.0/24.
I've also tried to add an ACL for the specific IP for inside interface but with no results.

Cisco VPN client can't ping remote network.

I have recently installed a Cisco 5505 and have problems with some of the Cisco VPN Hosts I connect to using the Cisco VPN dialer. The Cisco Dialer connects fine but I am unable to connect to any computers on the remote network.
I have tracked the issue down to the ones that work & the ones that don't. If the remote Cisco is on the same sub-net as the computers I am connecting to it works fine. If the remote Cisco is on a differant sub-net then the computer I am trying to connect to it won't work unless I set up a static nat for a given pc on my network.
When I run through the dynamic Nat for my network I get the following error on the 5505.
regular translation creation failed for protocol 50 src inside:192.168.97.215 dst outside:xx.xxx.xx.xxx
I have been trying to find a solution to this issue ever since I installed the router and have not had any luck with any of the suggestions I have found on the Web. I have attached my config.
Any help would be appreciated.
Mike

Thanks for your response.
Yes that exactly the setup we are trying to get to work.
I have a call into them now and will check on their set up but I have no control over how they configure their routers I can only make requests.
I was hoping there was something causing it on my side as I deal with Hospitals and they can get very picky about their security.
I guess what is confusing me is it works if it goes through a Static Nat but not if it runs through our dynamic Nat.
Mike

How can I set up a new network on my apple tv when my remote app isn't picking it up because they aren't on the same network?

How can I set up a new network on my apple tv when my remote app isn't picking it up because they aren't on the same network? The actual remote doesn't work anymore, so I've been using the remote app on my phone but now that our internet changed, I can't do anything at all. Please help!

You can't use the remote app to setup a network. If your physical remote isn't working you will need borrow another or purchase a replacement.

I have a mac mini server which I want to set up for remote access from windows and mac pcs. How do I do this. I can access it form my home network OK

I have a mac mini server which I want to set up for remote access from windows and mac pcs. How do I do this. I can access it form my home network OK

Posted in error.

IP lan can't acces remote network through VPN

hello
i want my asa 5505 8.2(5) to access my proxy server on remote lan through VPN
my VPN is OK, all PCs of local network can access to remote network.
but ASA on local network can't access to remote network.
i think it's a NAT problem but ....
local network 192.168.157.0/24 local IP ASA 192.168.157.1
remote netword 10.28.0.0 /16
remote proxy 10.28.1.26
my conf
ASA Version 8.2(5)
hostname ASACTM
enable password GC3gU8Dqv5.xJLCr encrypted
passwd GC3gU8Dqv5.xJLCr encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.157.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 90.89.245.154 255.255.255.248
ftp mode passive
access-list InOutside extended permit icmp any any
access-list outside_1_cryptomap extended permit ip 192.168.157.0 255.255.255.0 10.28.0.0 255.255.0.0
access-list inside_nat0_outbound extended permit ip 192.168.157.0 255.255.255.0 10.28.0.0 255.255.0.0
access-list inside_nat0_outbound extended permit ip 192.168.157.0 255.255.255.0 192.168.57.0 255.255.255.0
access-list VPNRACTM_splitTunnelAcl standard permit 192.168.157.0 255.255.255.0
access-list InInside extended permit tcp 192.168.157.0 255.255.255.0 10.28.0.0 255.255.0.0 eq www
access-list InInside extended deny tcp 192.168.157.0 255.255.255.0 any eq www
access-list InInside extended permit ip any any
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500ip local pool POOLIPVPNCTM 192.168.57.1-192.168.57.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
access-group InInside in interface inside
access-group InOutside in interface outside
route outside 0.0.0.0 0.0.0.0 90.89.245.155 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.157.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 90.80.215.141
crypto map outside_map 1 set transform-set ESP-3DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet 192.168.157.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 192.168.157.121-192.168.157.150 inside
dhcpd dns 10.28.1.16 194.2.0.20 interface inside
dhcpd wins 10.28.1.16 10.28.1.7 interface inside
dhcpd domain vignes.local interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy VPNRACTM internal
group-policy VPNRACTM attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPNRACTM_splitTunnelAcl
default-domain value vignes.local
username admin password 6QiRA9AlUbU.gFTP encrypted privilege 0
username admin attributes
vpn-group-policy VPNRACTM
username ICS1 password 5nDKAM1RJweYzrBO encrypted privilege 0
username ICS1 attributes
vpn-group-policy VPNRACTM
tunnel-group 90.80.215.141 type ipsec-l2l
tunnel-group 90.80.215.141 ipsec-attributes
pre-shared-key *****
tunnel-group VPNRACTM type remote-access
tunnel-group VPNRACTM general-attributes
address-pool POOLIPVPNCTM
default-group-policy VPNRACTM
tunnel-group VPNRACTM ipsec-attributes
pre-shared-key *****
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:e2c2e2223cb7d5d83af808bb0a2b2636
: end
thanks a lot

What do you mean by you would like the ASA to access the proxy server at the remote end?
What configuration/command have you configured on the ASA for the ASA itself to access the remote proxy server?
Do you want the PC behind the ASA to access the remote proxy server, or you want the ASA itself to access the remote proxy server?
How do you want to access the proxy server?

How can I manage new Firefox for Mac on my network. Control users Home Pages for Mobile User Accounts.

I am running Mac Computers in a School. Current Mountain Lions OS and current Firefox Browser. We log in using mobile accounts. How can we manage Firefox so all users get the same home page and settings.
If I can do locally or through a profile, that would be great

hello, you could use the mozilla.cfg file in the firefox program folder in order to lock or set certain preferences - here is some general information on how to set that up: http://kb.mozillazine.org/Locking_preferences
and specific guide to set the homepage can be found here: http://mike.kaply.com/2012/08/29/setting-the-default-firefox-homepage-with-autoconfig/ (this blog also contains may other helpful resources for deploying firefox)

Apple TV 1st Gen can no longer connect to wireless networks

My Apple TV (1st Gen) has recently lost the ability to connect to either of our wireless networks at home. I rean the diagnostics at the reset screen and the Apple TV says it is performing normally. In the settings, whenever I attempt to connect to a wireless network, I am now only offered "Other..." as a choice. Proceeding to the next screen, I enter the name of the network closest to the Apple TV -- an Airport Extreme set up for 5 GHz that this Apple TV connected with daily up until 2 days ago. The Airport base station is perfoming normally, as my MacBook Pro can see it and establish a network connection without any difficulty. The issue is limited to the Apple TV. I did a Factory Restore, and now when I go to Wireless Network > "Other..." > Enter the name of the wireless network" the resuit is always the same, and error message stating: "There was a problem connecting to the network. Check your settings and try again. (-4)".
This message comes up almost immediately, without requesting a WiFi password -- suggesting to me that this Apple TV has lost the ability to connect to ANY wireless network due to a hardware failure.
Q: Has anyone else in the Support Community had a similar experience with their 1st Gen Apple TV, and if so, did you find a solution to it?
Note: When I first noticed the connction to this Apple TV had gone stale (greyed out in the iTunes Airplay Speakers list), and prior to doing the Factory Restore, I could play back iTunes content stored on the hard drive, but could not connect to the local wireless networks. I noticed that the Apple TV was running very hot -- it has alwasy run pretty hot to the touch.
If this Apple TV has died, I will get a 3rd Gen Apple TV, but wiill then have to work through the HDMI to Composite video + Audio issues, as this Apple TV is connected to our older (non-HDMI) TV.

Follow-up: Able to connect with ethernet cable, downloaded software updates, connected to iTunes, and synchec content.
Next, disconnected the ethernet cable. ATV1 froze and was restarted using the Menu + ( - ) combo on the remote. Re-ran diagnostics yeilds: Apple TV is working fine.
Restarted, then went to configure the Wirelss settings. Apple TV once again does not show either of the two wireless networks. Selecting "Other..." and entering the SSID yields the same immediate response:
"There was a problem connecting to the network. Check your settings and try again. (-4)"
No change on the wireless front :-( Bummer.
Looks like an ethernet connection is the only option left to continue using this Apple TV 1st Gen.
Thanks for your help. -- Paul

HT201250 Hello i am using TimeMachine to back-up entire Mac image (data + system) on an usb-local drive. I would like (on top of it) add a specific plan to back up some files on a remote network drive. Does TimeMachine support multiple back-up plans ? How

Hello i am using TimeMachine to back-up entire Mac image (data + system) on an usb-local drive. I would like (on top of it) add a specific plan to back up some files on a remote network drive. Does TimeMachine support multiple back-up plans ? How ?

Time Machine is capable of backing up to multiple locations, and can be used to back up to both a local hard drive and a networked drive (provided that that drive is in or connected to a Time Capsule or another Mac that is sharing it over the network). The catch, though, is that you can't specify different things to back up to different destinations. Whatever you exclude from Time Machine backups is excluded from ALL backups, and whatever is included is included on all.
So, get a large enough drive that you can back up everything you want in all locations, or use something else for maintaining the network backup.
More information on these topics can be found here:
How do I set up Time Machine to a shared drive on another Mac?
How do I set up Time Machine to a Time Capsule or Airport Extreme?
"Rotating" Time Machine backup disks

Can multiple PCs access one remote panel at the same time?

I've written a program in labview 7.1 to monitor/control a labview application running in the test cell through Remote Panel. I and my coworker can remotely monitor and/or control this labview application individually. But if my coworker has the remote panel displayed on his PC and I try to get the remote panel on my PC, I get a labview error (63) as below:
"LabVIEW: Serial port receive buffer overflow.
LabVIEW: The network connection was refused by the server."
My question is: Can multiple PCs access one remote panel at the same time?
Thanks in advance!
Y

Sorry I wasn't clear. The remote panel license is separate from the number of LabVIEW development licenses. Pricing information on remote panel licenses can be found here.

Can't log on with administrator user by finding the message "The task you are trying to do can't be completed because Remote Desktop Services is currently busy. Please try again in a few minutes. Other users should still be able to log on.

Hi,
Now, my Windows 2008 R2 Enterprise server are running in the domain. It have problem about some one in my team have remote my server with the user administrator while I'm remote it now. It make my session loss. I tried to remote it again but I found
the message at the log on screen about "The task you are trying to do can't be completed because Remote Desktop Services is currently busy. Please try again in a few minutes. Other users should still be able to log on."
Now, nobody can't remote with administrator user into this server. I have check the application log. I found the error message like this.
++++++++++++++++++++++++++++
Source: Desktop Window Manager
Event ID: 9003
Detail: None The Desktop Window Manager was unable to start because a composited theme is not in use
++++++++++++++++++++++++++++
Source: Microsoft-Windows-Winsrv
Event ID:10002
Detail: The following application was terminated because it was hung: mmc.exe.
++++++++++++++++++++++++++++
Source: Microsoft-Windows-Winsrv
Event ID:10002
Detail: The following application was terminated because it was hung: javaw.exe.
++++++++++++++++++++++++++++
Source: Microsoft-Windows-Winsrv
Event ID:10002
Detail: The following application was terminated because it was hung: Explorer.exe.
++++++++++++++++++++++++++++
Source:Desktop Window Manager
Event ID:9009
Detail:The Desktop Window Manager has exited with code (0x40010004)
++++++++++++++++++++++++++++
Source:Microsoft-Windows-Winlogon
Event ID:6005
Detail:The winlogon notification subscriber <Sens> is taking long time to handle the notification event (Logoff).
++++++++++++++++++++++++++++
In addition, I can log on this server with other user but I can't log off by it's showing the message "please wait for the system Event Notification service". Normally, the problem can solve by reboot the server. But how can be solve this problem
by we do not reboot the server?

Hi,
The cause of unable to remote back to the server seems to be services hung, please try to reset session as the article below guides to see if it works:
Windows Server: Remote Desktop Error: The task you are trying to do can't be completed because Remote Desktop Services is currently busy
http://social.technet.microsoft.com/wiki/contents/articles/28636.windows-server-remote-desktop-error-the-task-you-are-trying-to-do-can-t-be-completed-because-remote-desktop-services-is-currently-busy.aspx
If the issue can always be re-produced, then I would suggest you fully patch the system.
More information for you:
The task you are trying to do can't be completed because Remote Desktop Services is currently busy. Please try again in a few minutes. Other users should still be able to log on
https://social.technet.microsoft.com/Forums/windows/en-US/c58bfbd5-1d63-47e3-a489-6d8c8778b76b/the-task-you-are-trying-to-do-cant-be-completed-because-remote-desktop-services-is-currently-busy?forum=winserverTS
Best Regards,
Amy
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Can WLC2504 manage AP in remote networks?

Similar Messages

Maybe you are looking for