Can you give me some idea why Temperature Need to cool down before you can use it. as this appears after 5min using.

Dear Sir/Madam,
My questions:
Why Temperature appears and ipad need to cool down after 5m of using and not even hot. The guy from the apple store where i bought my Ipad2 told me that the motherboard need to be replaced. Ca you help me and give me some idea on how much it cause of the motherboard.
Thank you
Victoria

if you need a new logic board for you iPad 2 i am sure the cost will be about 50% of what you paid for the iPad 2 $249.00, Take a look at this link, http://www.apple.com/support/contact/

Similar Messages

I have an error message reading "Iphone needs to cool down before you can use it". ?

I can only use the phone for maybe 4 minutes before this message appears with a yellow warning triangle. (Iphone 4S)
"Iphone needs to cool down before you can use it"
The phone is not warm and after a couple of minutes it is useable again only to repeat the same message a few minutes later.
I've done a restore which made no difference.
Anyone have any ideas/similar problem?
Cheers

iPhone, iPad, and iPod touch (4th generation): Keeping device within acceptable operating temperatures

Turned my iPhone completely off and then on. The lock screen then came up with no clock and when I entered my pin, it would not bring me in, it would just go back to the same lockscreen with no time. Now says Temperature, needs to cool down

Stuck on screen saying Temperature needs to cool down before use for hours, I don't know what to do

Also, it does not say Swipe to Unlock, it says Swipe For Emergency. Maybe why the passcode isn't working?

Im from Philippines one of our carriers here supports 4G already on selected areas, Im currently in the area where this carrier has 4G now, I couldnt see my phone on 4G signal. Can anybody give me an idea, why?

Im from Philippines one of our carriers here supports 4G already on selected areas, Im currently in the area where this carrier has 4G now, I couldnt see my phone on 4G signal. Can anybody give me an idea, why?

Here's why:
The iPhone 4S does not support 4G. Only the iPhone 5 does (of Apple's iPhones).
Here's an iPhone comparison chart:
http://www.apple.com/iphone/compare-iphones/

Hi guys, my ipad2 says that it needs to cool down before using. It has been sitting in a cool place over a day now but the message still pops up. Any other ideas? or help?

Hi guys, my ipad2 says that it needs to cool down before using. It has been sitting in a cool place over a day now but the message still pops up. Any other ideas? or help?

Is the iPad Off and not connected to the charger?
 Cheers, Tom

Can anyone give me some ideas/settings for night scape photos w/ a full or partial moon in them?

I have been trying to get night time "landscape" photos with a full or partial moon in them. The mountains, water, sky and stars all come out great but the moon and its reflection come out very bright, round and pretty blurry. I usually use my kit lens, tripod, shutter remote;100 to 400 ISO, 8-30 seconds on the shutter speed, aperture 4 to 8,10,16...,metering mode "spot", and using the Manual zone. Is there a way to "get it all"? ~Thanks!

You can do this... but the "trick" is to take the shot the evening BEFORE the "full" moon moon and not the of the full moon.
Whenever you have substantially mixed lighting problems (bright moon, dark city), you usually want to look for ways to bring the radically different exposure needs closer together so that the exposure needs from the moon are not so substantially different than the exposure needs of the city. By shooting the cityscape at "dusk" instead of at "night" you are helping to bring the exposures closer together AND usually a deep blue (end of dusk) sky color looks more appealing than a black sky anyway.
The moon rises a bit later each day (since there are 24 hours in a day but there are about 29.5 days in a Lunar month). The actual time between moonrises varies a bit.
You want to be in position a bit before sunset. You'll notice that the moon actually appears to be pretty much "full" one day before it it is technically the official "full" moon. But since you are taking the shot a day early, you'll get a dusky blue sky behind the full moon rather than a black sky. On the night of the full moon, the Earth is between the Sun and Moon -- so the moonrise actually occurs "at" sunset. At that time, however, the moon will be right on the horizon and not up high enough to be visible over the buidlings in your city nightscape shot. By the time the Moon is high enough, dusk will have completely ended and the sky will be black.
By getting there a a day EARLY, there will still be some light once the Moon is high enough. This will completely change your exposure.
The Moon looks best photographed with something called the "Loony 11" rule -- which suggests a correct exposure with f/11 and setting the shutter speed to the inverse of the ISO speed. So at ISO 100 you'd use 1/100th sec if you are using f/11 (and if you use something other than f/11 you can change the shutter speed to compensate.) But this rule is for when the moon is high. Nearer to moonrise the thick atmosphere will reduce the amount of light and will likely require an extra stop to expose (e.g. you may need to slow the shutter to 1/50th at ISO 100 with f/11 - use a tripod or boost ISO speed slightly (I'd use a tripod).
Incidentally, if you use a long focal length it will create the illusion of a very large moon relative to the size of the cityscape below.
You can use the "Photographer's Ephemeris" website (or application) to your advantage here. I use a mobile app named "Sun Surveyor" but I see the folks who made the "Photographer's Ephemeris" website have also created an app. The idea behind it is you give it the location and date and it will tell you not only the rise & set times for the Sun and Moon... it'll visually plot the position angle (compass heading) and altitude angle up from the horizon for any time of the day. And they also use a map. So... suppose you want to get a picture of a city with the moon just above a specific building... the website and/or app will tell you exactly where you need to stand AND at what time you need to be standing there to get that shot with the moon precisely where you want it to be.
Photographers Ephemeris: http://photoephemeris.com
Sun Surveyor: http://www.sunsurveyor.com
Both of these do "roughly" the same thing (I first learned about Photographer's Ephemeris... but at that time the only way to use them was via their website and desktop app (which is free, btw) -- they didn't have an app. So you had to use your computer to pre-plan you shot before leaving home.) That was great -- but didn't help me on vacations where my computer is back at home.
Then I learned about Sun Surveyor (which was basically Photographer's Ephemeris... but in "App" form for my iOS mobile device.) After I bought Sun Surveyor (it's a few dollars).... Photographer's Ephemeris launched their own app. So now you have at least a couple of options.
Good luck!
Tim Campbell
5D II, 5D III, 60Da

Why does my iMac shut down before it can boot up After installing 7.3 update on my iMac?

After installing 7.3 last night, I hit restart and went to bed. My intel iMac i7 3.4ghz was powered down this morning, and only after unplugging,waiting, rep plugging,
It finally powered on, only to boot to the gray apple screen, go black and silent. (this exact issue had me lugging it back to apple a month after purchase, today is 93 days)
Recovery mode got me about one second further in bottling up before shutting off.
I was forced to upgrade from an unproblematic pc g5, after iCloud, so do not own snow leopard and was told I would never need a re install disc.
Has anyone having the powering off during boot after updating to 7.3?

omg. I would copy and paste your original post to the iMac section. You're talking about a fine piece of equipment, the Intel iMac i7 3.4ghz , and you should not be having such problems. Maybe others in the iMac i7 community might also have some ideas.
Re: the safe boot. That's good that it worked. This is fairly new and very, very helpful with a dead computer because at least you can get to Safari, get to the Internet and get ideas and seek help.
But why did it shut off after a while? That's not right. No reason it should have done that.
From something you said I would worry about your power supply problem or this PerIphrEa. I don't know what that is but Migration is built into Lion OS, no? Third party perificials (or apps) can certainly cause conflicts and not work as well as advertised.
Also, seriously, I would get some tape, like duct tape, and tape up that loose power supply.
Why do you need something extra for your migration? (Or is the reason your old PowerPC G5 needs to run Lion but it can't?).
If that is the problem, here's an idea. Continue the canibalization of your PowerPC G5, take out it's hard drive(s). Buy an 'enclosure' to put the hard drive in and allow you to connect this hard drive to your new machine, the beautiful iMac i7, using the old hard drive as an external drive.
I did exactly this with my old PowerPC G5, using this enclosure, a Macally G-S350SUA, info at: http://www.macally.com/en/product/ipod4show.asp?ArticleID=215
I now use this for my Time Machine backups.
Re:What is the proper amount of time the computer needs to be unplugged? This would worry me. I turn off my comuter NOT by unplugging it but by holding the power on button for about 3-4 seconds and then it turns off.
I then wait 5 long seconds before pressing the power on button again to turn the computer back on.
Having to plug in and unplug and plug in and having to wait ten minutes for it to work is not normal.
Is there a power supply issue in your home, perhaps?
Considering the value of this machine and the fact that it may still be under warrenty, I'd consider the weeklong diagnostic. Would the machine have the same need to wait ten minutes to turn on at the Apple place?
What if you plug it in at a friend's house, or an office or library? Would it still take ten minutes before you could turn the machine on?
It might seem horrible to have to wait a week...or to do this again and again but I'd recommend taking full advantage of your warrenty, keep sticking this problem back to Apple and insist it gets made right. It will be worth it in the long run.

Can you give me some ideas on which to buy between macbook air and macbook pro?

     I am going to start another year in college very soon and I need a laptop to handle my school work or projects. I don't know what to choose between Macbook Air 13" (2013) and Macbook Pro 13" (RAM 8GB - Not Retina Display). Here are what I need to do on computer:
     - Long time surfing through the internet.
     - Social network : Facebook, Instagram, Line, Skype ....
     - Watching movies online (mayb more than 3-4 hours)
     - Typing documents or making slide shows.
     - A lot of documents, HD videos/movies, photos and music.
     - Using some graphic/plan design programs such as CorelDraw, Photoshop, Illustrator, AutoCad and so on. (Monthly but I still have to use it.)
     - Games are no needed cuz m not a gamer.
     That's all or maybe more, but I can't think of right now. My money is around 1500$. If you guys think I might need Air, should I configure it to match my expectations? I hope to having some good ideas from you. Thanks in advanced.

Ive got BOTH the Pro and AIr youre interested in, for what YOU say you want, Id get the Air.
Since you said you were only going to "some graphic/plan design programs", the Air is perfect for moderate Photo editing.
and you said no games.
Air has fewer parts, only one moving part (the fan), lite as an Ipad (almost) but a full powered computer.
No HD heads to crash, fewer parts = simplicity = less to fault.
Runs cooler than anything else out there (which = durability). Heat is a killer on a scale of 10X over that of accidents.
Pack around a regular notebook around about 20 days, then an Air, .....after that the standard laptops stays at home.
Air is the only Mac that has Haswell, 802ac wifi, and incredible 12hr. batt life in 13" I5.
Get the 13" much longer battery life, and the screen real estate is better, Ive owned both 11" and 13".     13" also has an SD card slot the 11" doesnt have.
Picture of macbook Air simplicity below

Could you give me some ideas about striping html tags?

Hi everyone:
I am wondered where to get this component in J2se api or another projects(like commons)?
If you know where to find it? Please tell me directly...
Thanks a lot!!

Thank you hiwa, I will google it named HtmlEditorKit.Search the Swing forum: http://forum.java.sun.com/forum.jspa?forumID=57
>
>
I can not do this with simply regex as you said "it
is dirty", because it maybe filter some useful
information like "<NotHtmlTag>".No. Use a proper regex. Read the java.util.regex.Pattern class documentation.

My Mac Desktop 10.6.8 can no longer open PDF files. Can someone give me some ideas to try?

I am having problems with my Preview app. I can't open any PDF files in Safari or Firefox.

Adobe Reader works well with Snow Leopard. What doesn't is its crappy internet plug-in. Quit all browsers, open /Lbrary/Internet Plug-ins, and remove these two:
AdobePDFViewer.plugin
AdobePDFViewerNPAPI.plugin
Relaunch your browsers and that should do the trick. For better viewing of PDFs in a browser, something I'm loath to do, install the Schubert plugin.

My phone intermittently States that the temperature is too high and so needs to cool down!! Howeve, it feels cold and I am only able to shut it down to restart it. This only temporarily resolves the problem. This started when battery was replaced.

Iphone 5 is stating that the phone is too hot and needs to cool down before it can be used. However the phone actually feels cold!! I can turn the phone off and restart it which temporarily resolves the issue. this issue stated once Apple replaced my battery. Any solutions or idease??

Take it back to Apple and have them look at it.

Can you give me some reasons about why I need to buy an iPod touch 5.Although I have the iPhone ,iPod nano, iPad ,MacBook pro,I think the iPod touch 5 is so attractive that I can't help buying it at once.If I have it,what I can do with it,can you tell me?

can you give me some reasons about why I need to buy an iPod touch 5.Although I have the iPhone ,iPod nano, iPad ,MacBook pro,I think the iPod touch 5 is so attractive that I can't help buying it at once.If I have it,what I can do with it,can you tell me?

All I can say is that I REALLY like my Touch 4th gen because I have all sorts of capabilities in a small form: e-mail, web browsing, news, weather, books, magazines, etc. etc. Plus lots and lots of apps out there, including so many free ones. I use the Cloud a lot so it's great to have everything sync'd to my MacBookPro (e-mail, Evernote, Pocket, etc.)
It would be easier, though, to do some of this, especially magazines, on the iPad mini, but, again, I love the small size of the Touch.
As for the 5th gen instead of the 4th, the fifth has Siri and the 3D feature in maps, which are great. And I'm sure it's a lot faster in iOS 6 than the 4th gen. And cool colors!
Don't know if this helps . . .

Hsawwan ,can you give me some help?

Although I'm very new, I have made up my mind to become a Oracle ACE in Ebs field.
I will achieve this aim by working hard .
I have made every mental preparations.
can you give me some advice ?

Hi,
Have a look at the following thread, it should be helpful in answering your questions.
ACE
ACE
Regards,
Hussein

Can you give me some suggestions for encryption decryption

ok i've written my own encryption decryption techniqu can you suggest me some better methods
Attachments:
EncrypDecrypt2.vi ‏59 KB

karthik9 wrote:
Not to publish ... this is very simple ... i just want to know should i improve this or scrap this
You haven't replied but I guess I haven't answered your question either...
Sure it works but from a LV programming standpoint it is very redundant and Rube Goldberg like.
IMHO you should scrap what you have or at least clean it up.
I am a long ways from being a LV expert but there are the things that pop right out at me when I see your code.
You use identical code in three places, make it a sub-vi.
Why start with a constant of -1 and increment it once inside your for-loop? This value will always be 0.
Don't use array size to set the number of iterations of your for-loop then use the iteration counter to index an array inside the loop, use auto indexing.
Your block diagram is sloppy and hard to follow.

Who could you give me some general idea

hi all
who could you give me some general idea about that
developping a web service that may be used for monitoring the performance of the Windows PC on which it runs. The web service will return key performance metrics, such as peak performance,maximum memory, current load, and current available memory. A secondary aim will be to develop a portlet that will provide an interface to the service.
Tomcat or J2EE web server, JSR-168 compliant portlets, and Web Services for Remote Portlets (WSRP) should be metioned!
thanks
with regards
Dashan

First of all, if you want to create a chess board, create a panel with a grid layout. The grid layout will carry the number of rows and columns that you need.
Second, you will have to set the color of each grid alternatively to black and white.
After you have done this, your chess bord is ready.
Now...coming to the mouse events:
You will have to implement a MouseListener and implelemnt the method mouseClicked(MouseEvent e) attached to the container.
So when you use the methods getX() and getY() based on the MouseEvent e...
e.getX(); //Returns the horizontal x co-ordinate
e.getY();// Returns the horizontal y co-ordinateHope this helps.
Vijay :-)

Can you give me some idea why Temperature Need to cool down before you can use it. as this appears after 5min using.

Similar Messages

Maybe you are looking for