Can you hook a jetpack to a wireless router

can you hook a jetpack up to a wireless router

http://community.spiceworks.com/topic/377853-wireless-router-as-a-bridge-to-verizon-jet-pack
It can be done. However I normally use my broadband network and a wireless repeater. I use Netgear and Belkin, both work together nicely and you can place repeaters all over your home and property.
Additionally on my broadband modem I have opened up a WiFi connection for emergency access. Its buttoned up with high security but I access WiFi on the Netgear R6300 both wireless and hard connect(RJ-45) and through the Belkin Repeater both WiFi and hard connect (RJ-45) and I use my broadband modem/WiFi as both WiFi and hard connect (RJ-45) with absolutely no interference.
The basic principle is or should be the same with the jetpack as used as a pass through . See the link above.
Good Luck

Similar Messages

Can you hook up multiple pairs of wireless headphones to the MDR-DS6500 base unit

Can you hook up multiple pairs of wireless headphnes to the MDR-DS6500 base unit or do you need a base unit for every pair you would like to connect to your tv? if you can which models are compatible?
Thanks

Do I need an AirPort to attach to each set of speakers that I want to connect, or is there another kind of receiver I can hook up to the speakers that do not have any kind of WiFi or Bluetooth configuration?
You basically have two choices: 1) Place an AirPort Express base station at each of the speaker locations, or 2) Use an AirPlay-Ready receiver that offers whole-home audio support. The latter would require that all speakers be connected back to the receiver.
Also, if I am planning to set up the airplay by using the extended network configuration, then the Wifi base station does not need to be an AirPort station? I have Fios and had trouble last time I tried to hook up an AirPort in place of the router that they provided.
The AirPlay networking protocol requires either a wireless or wired connection between the AirPlay server (typically iTunes) and the AirPlay speaker (AirPort Express, Apple TV, or an AirPlay-Ready receiver or speaker). AirPlay will traverse over an extended Wi-Fi network regardless of which manufacturer hardware is used.

Can you hook up to ethernet

Can you hook up ethernet to express; have access to multiple computers, pick the one you want, drill down to that itunes library and play the associated songs and playlists? Also, is there a way to play internet radio; lastly can you control this via an iphone? if so how? is there an app that can allow users to access thier windows computer and see thier itunes library?

Yes it sounds correct. They can be Windows computers, they just have to be running fairly recent versions of iTunes and they all have to be on the same network. Wired or wireless makes no difference.
If you have an Express it can also join your network wirelessly or via Ethernet. They can be configured to connect to your network either way.
With the iPhone's Remote app you simply click the gear icon and click "add an iTunes library". You go to that computer and type in the code to authorize it. Sharing has to be enabled in iTunes Preferences also. Home Sharing uses your Apple ID so the other computers all have to use the same one.
Also, if you are using Windows you will almost certainly have to configure its firewall or anti-virus software. Such things are designed to hinder all sorts of communication and they're all different so you may be on your own trying to figure that out.
Apple has lots of instructions regarding Home Sharing, if you're not getting anywhere start with this:
http://www.apple.com/support/homesharing/

How many devices can you use on an airport express wirelessly?

How many devices can you use on an airport express wirelessly? Does it matter how many devices you have?

The Express supports up to ten clients.

Can you hook an ipod classic up to a stereo receiver with an RCA jack adapter?

Can you hook an ipod classic up to a stereo receiver with an RCA jack adapter?

Something like this?
http://www.daydeal.com/product.php?productid=11487
B-rock

Can you use the Express as a wireless bridge?

I need to get an ethernet connection to a slingbox next to my airport express. My airport express is currently configured as a client that connects wirelessly to my netgear router that connects to my cable modem. I can play itunes on any computer to the airport express.
Is it possible to use that ethernet port on the AE to bridge my slingbox back to the netgear/cable modem?

Can you use the Express as a wireless bridge?
Yes as long as WDS is used with a compatible device.
Is it possible to use that ethernet port on the AE to bridge my slingbox back to the netgear/cable modem?
No. The Netgear base station is not compatible with Apple's WDS implementation.

Can you connect an iMac to a Lynksys router without an airport express or base?

can you connect an iMac to a Lynksys router without an airport express or base? I tried running it from cable>modem>router and it doesn't sling to the iMac. The airport card in the Mac does seem to be on, and there is a network connection set up. It's an intel iMac7,1.
At my house I have the same configuration going to an old Mac laptop and it works fine.
Any ideas? Thanks

Csound1--
If you mean does the network appear on the Mac when I look for it, then yes.
I think my friend had her wifi network set up properly, or it wouldn't be showing in the list of networks when I check.
the router is a Lynksys WRT160N V3.
I don't think she has the security code so I can check what's actually hooked up (the network name on screen at least appears to be locked). She's had the computer out to the shop and back recently and has never even run anything off the wireless.
I have a feeling I'm going to have to call her cable provider to sort it out. I'm hoping to avoid that. I don't know Mac at all. I could troubleshoot on my PC.
Ultimately, I want to be able to hook a Roku box to her TV to run Netflix.
Any help would be greatly appreciated.

Can you connect an iMac to a Lynksys router without an airport express

can you connect an iMac to a Lynksys router without an airport express or base? I tried running it from cable>modem> wireless router and it doesn't sling to the iMac. The airport card in the Mac does seem to be on, and there is a network connection set up. It's an intel iMac7,1. I'm not familiar with Mac, I'm trying to help out a friend.
At my house I have the same configuration going from my PC to an old Mac laptop and it works fine.
I think my friend had her wifi network set up properly, or it wouldn't be showing in the list of networks when I check.
the router is a Lynksys WRT160N V3.
Oh, and if I do run her computer trying to use the wireless, I don't get an internet connection at all. I have to have it hardwired straight to the modem.
Sorry I've asked this twice, but I haven't had any luck. I must just not know where to find things on the Mac. I did try other places in forum before posting again.
Any ideas? Thanks

We don't know a thing about your iMac or what version of OS X it's running so it's very difficult to help you. Please note that information and also please complete your profile, then that infomation will be listed when you post in your next thread. You can complete your profile by clicking Your Stuff in the upper right of this page then click Profile and fill in the pertinent information.

Can you use a roaming network and wireless extender at same time?

Greetings community - I've been struggling with an attempt to extend my wireless network for some time now. Please forgive my ignorance on the topic - I realize how 'simple' this is for many of you. Let me summarize:
What I have functioning:
1. Comcast telephony modem
2. 5th gen Airport Extreme as main wireless router connected to modem via Ethernet (corner of floor 3)
3. 2nd gen Airport Express as wireless extender (hooked to a stereo on floor 2)
What I want to accomplish:
1. I have poor wireless signal on my sun porch (corner of floor 1 opposite side of building as modem)
Extra equipment I have:
1. Another 5th gen Airport Extreme
2. Another 2nd gen Airport Express
What I have tried (and failed at):
1. Initially I set up the second Airport Extreme as a second wireless extender and placed it at a further point away than my first wireless extender. I quickly realized that set up does not function appropriately and one cannot connect to the further extender (I read about that on the apple forums).
2. I tried placing the second Airport Extreme in a different part of the house at equal distance from the main router as the first wireless extender. It's capability to extend was minimal if any.
3. I tried connecting the Airport Extreme to the main router via an Ethernet cable with the hopes of creating a roaming network (which I read about on the apple forums). I would have to come up with a way to run the Ethernet through the house but I'm willing to cross that bridge later. Once I got that set up, the 2nd gen Airport Express which was previously set up as a wireless extender is no longer recognized. Argh!!
Questions/Theories/Suggestions:
1. Is it possible to have a wired extender (via Ethernet) function at the same time as a separate wireless extender all connected to the same router? If so how do I do it?
2. I thought about keeping Airport Extreme #1 wireless connected to Airport Express #1 and call that Network 1. Then plug Airport Extreme #2 directly into the modem to create Network #2 and use Airport Express #2 as wireless extender. When I tried plugging both Airport Extremes into the modem, they both stopped functioning.
3. Do I get a second modem to put somewhere else in the house and use Airport Extreme #2 and Airport Express #2 in that fashion? My guess is Comcast will try to charge me a separate internet access fee to do that (boo!!).
I know there are a lot of brilliant folks out there. I'm sure someone can read this and see the 'obvious errors' in my ideas and attempts. I'm certainly open to new suggestions as well.
Thank you in advance for your time and advice.
- The New Guy

Is is possible to rename the AEx 2 a different network name from the AEx1 and AE 1 (even though they are all connected to each other)? And say it is possible, would that potentially preventing the jumping?
No, in extend wireless the names must be the same..
However since you are creating a network on AE2 which is extended by AEx2 then you can indeed use a different name.. but it must be both,, AE2 and AEx2.
2. Even more crazy - if I did (could) give the AEx 2 a different network name, could I use my AE 2 as a wireless extension to that second network? Or is this just getting out of hand now?
You have lost me now.. there are ways and means.. but let me recommend a better solution.
Use EOP (homeplug in US) adapters if you cannot run ethernet. Multi-storey houses where you have heavy concrete construction are never going to work well with wireless alone. You are much better getting ethernet properly installed (which is the only 100% guaranteed method).. or buy a set of EOP adapters and give them a try.. they work in some cases and not others.. but better than wireless when they do work.
Otherwise I think you need higher power wireless routers.. but I can suggest you do the setup in a more controlled manner.
In other words do not use auto as per the airport utility.. use very short wireless names, different for both bands.. and fixed wireless channels.. then test which band works better.. Then you can do a link.. which will be slow but might give you better performance.
So..
Link1 Main AE1---- AEx1 This is wireless extend.
Link2 AEx1--ethernet--AE2. AE2 is in bridge mode and is also set to create a wireless network. (Use different wireless name here to prevent confusion).
Link3 AE2-----AEx2 Second wireless extend.
This overcomes the Apple limitation on multiple extends. It is not great setup but might get wireless to where you need it.. And better speed than you can get now.
NOTE>. I would personally never do this.. I will run ethernet forevermore.. having tried and tried in various places and using all kinds of equipment.. my conclusion is.. wireless is not suitable.. unless you can get enough signal in from one AP.. everything behind it must be ethernet.
It is much more expensive in some cases.. but ethernet works.. nothing else can be guaranteed to work.

Can you hook two printers to the airport extreme

Can I hook up multiple printers to any of the airport devices? the middle one has more than one port - one for printer and one for hard drive. Can I put a printer in each port?

Hi - you can connect mutiple USB printers via a USB hub - you can also connect multiple printers to the ethernet ports on an Extreme or Time Capsule - you can do the same with an Express with an ethernet switch - you can also do it wirelessly

Can you use a time capsule's wireless hard drive capabilities without plugging it into a wireless router?

I recently used it as a bridge router from another router but then turn that function off. But now if I just have the time capsule set up on its own I can't even find it on airport utility. It seems funny as it itself is a wireless router...
Thanks for your help

A "hard reset" will not erase the Time Capsule's hard disk. That would require a separate procedure. Your backup data will not be affected.
You can connect it to a router if you wish, but a "hard reset" is more likely to result in less confusion.
Read to be sure you perform it correctly: Resetting an AirPort Base Station or Time Capsule FAQ

Silly question, maybe. I want to change from Verizon DSL to cable, but cable company doesn't supply router. can I use my Airport Extreme as wireless router?

We currently have the following wireless home-network configuration, powered by Verizon DSL.
2 macbook pro’s
1 emachine
HP PhotoSmart 6122 all-in-one printer
Apple TV
Apple Airport Extreme Base Port A 1408
Westell 7500 router
Thinking I’d get wider wireless coverage throughout my 2 bedroom home, I purchased the Airport Extreme. It is connected to the router via its sole usb port. The result was only a tiny increase in speed, and no increase in coverage, so I don’t know why I have it.
We now want to change from DSL to cable, thus ditching Verizon. Our new cable provider supplies the cable box, but no router for wireless networking.
Here are my questions.
Can I use the Airport Extreme (AE) as a wireless router?
If so, how should I hook it up? Should the usb cable go from the AE to the cable box, and all the other devices connect wirelessly?
If not, how should I be using the AE to some advantage? What can I get out of the investment?
Thank you very much for your help! Beatriz

What I wrote has nothing to do with what the cable company charges for their installation. And, usually they will help with the router setup even if you supply your own router. I don't know what they will charge for the modem.
Note that you need to get just a modem. You don't want a modem/router combination. That will make using an AEBS effectively nearly impossible. You will need to ask specifically for just a standalone modem, and that you will supply your own router.

Can anyone help me with my wrt54gs wireless router?

We have the wrt54gs V7 wireless router hooked up to an older HP desktop computer (running on WindowsXP) and have had a work laptop hooked up to the wireless router for 2 years w/o any problems. We just bought a new laptop running on Windows 7 and although we can see our wireless as an option, have keyed in the Secure Key #, we still cannot connect. I tried running the Linksys set up cd that came w/ the router to set up the wireless connection on the new laptop and it says the disk is not able to run on the operating system. I went thru the process to add a new wireless computer from the desktop/using a USB drive to load the wireless app but when I plug in the USB to the new laptop it stops the set up and says the wireless radio is off on the laptop even though the wireless is on. I am at a loss on how to connect!! 1) how do I get the new laptop to connect to our current wireless router if the set up disk and the USB drive methods do not work? 2) if we eventually get rid of the desktop computer what do I need to do to ensure our wireless connection stays on?
I am ready to throw the new laptop out the window so any help is MUCH appreciated!!

You don't need the setup disk for anything. Connect with a wired computer to 192.168.1.1username blank, password 'admin' (or wahtever you changed it too). Now look up your security and enter it into your new laptop.
Go here for help.

I have a new macbook pro hooked up to a belkin wireless router. My HP officejet printer is also connected to the router. I cannont get the printer to work from my computer without restarting my computer evertime I want to print. How do I fix this?

I have a new Macbook Pro hooked up to a new Belkin wireless router. I can connect to the internet without a problem. I have an HP officejet printer hooked up the the router to work wirelessley, The router is reading it as connected. My computer reads it as offline. If I reset my computer it will print whatever the first thing is in the que but nothing else and does not work after that. Is there some sort of setting that I am missing? I am trying to set this printer up to work wirelessly from three mac laptops in my house but I can't even get it to work on one right now. Any help would be awesome

Mac OS X 10.7 Help: Troubleshoot a network printer

Hooking up/configuring a WRT54G2 wireless router to my wired modem/router.

Problem description: I have bought a wireless router (Linksys WRT54G2) in order to connect it to my ADSL2+ modem/router (a TP-Link TD8840) to provide wireless internet access to my iPhone and laptop. I only intend to power on the wireless router when I need it, not have it on all the time wasting electricity.
Attempted fixes: Configuring the WRT54G2 per the install CD, but this appears to mean I must have my wireless router always powered on in order to access the internet even when I'm not using the wireless. Ideally I just want to turn on the wireless router as and when I need it.
Operating system: Windows XP Pro (32-bit) SP3.
So, as my description says, I bought a WRT54G2 so I can browse the web on my iPhone using my DSL connection rather than the cellular (3G) network. I currently have the WRT54G2 plugged in from one of its four ethernet ports to an ethernet port on my wired modem/router. The IP of my modem/router is 192.168.1.1, which also appears to be the default ip for the WRT54G2 So I can't access my WRT54G2's admin screen to properly set up the network.
At this point I feel as if I should reset the WRT54G2 to factory settings and start from scratch, but I lack a coherent set of instructions to point me on my way. It's a bit frustrating because I'm pretty good with computers generally, but networking obviously is not my thing. Can anyone please help

Hi modeski,
To setup your WRT54G2 router and make it work with your modem/router there, chnage first the IP of the WRT54G2 from 192.168.1.1 to 192.168.2.1 before you connect it to the modem/router.
In other words, you are cascading two routers.
Hope this help!

Can you hook a jetpack to a wireless router

Similar Messages

Maybe you are looking for