Can you use two bluetooth devices on iPad at the same time?

Want to use the wireless keyboard along with the Jambox wireless speaker. Will the iPad allow you to connect to two Bluetooth devices at once?  Thanks!

Seven is the Bluetooth max, but you should probably not do more than three or four and then depending on the BT protocols that each device is using.
I use my Apple BT keyboard and my Cellular Innovations BT headphone clip at the same time without any issue whatsoever.

Similar Messages

  • Can i use two bluetooth devices simultaneously with iphone 4s? Specifically,a bluetooth headset, as well as a new low energy bluetooth heart monitor?

    Can I use two bluetooth devices simultaneously with iphone 4s? Specifically a bluetooth headset as well as a new low-energy smart bluetooth heart monitor?

    I don't believe so.

  • Can I use two airport extreme base station on the same network

    Can I use two airport extreme base station on the same network

    Here is my network setup:
    D-Link DCM-202 simple cable modem (DOCSIS 2.0 compliant)
    attached via ethernet to
    5th generation AirPort Extreme Base Station - Main (Bought last week)
    attached via ethernet to
    4th generation AirPort Extreme Base Station - Remote (Bought about 11 months ago)
    The main AEBS is set to:
    AirPort Section:
    Base Station Tab -> Allow setup over WAN is CHECKED
    Wireless Tab -> Wireless Mode: Creat a Wireless Network, Radio Mode: 802.11a/n - 802.11b/g, Radio Channel Selection: Automatic, Wireless Security: WPA2 Personal
    Internet Section:
    Internet Connection Tab -> Connect Using: Ethernet, Ethernet WAN Port: Automatic (Default), Connection Sharing: Share a public IP address
    TCP/IP Tab -> Configure IPv4: Using DHCP
    DHCP Tab -> DHCP Beginning Address: 10.0.1.2, DHCP Ending Address: 10.0.1.200, DHCP Lease: 24 hrs
    NAT Tab -> The box following 10.0.1. is left blank, Enable NAT Port Mapping Protocol box is CHECKED.
    The remote AEBS is set to:
    AirPort Section:
    Base Station Tab -> Allow setup over WAN is CHECKED
    Wireless Tab -> Wireless Mode: Creat a Wireless Network, Radio Mode: 802.11a/n - 802.11b/g, Radio Channel Selection: Automatic, Wireless Security: WPA2 Personal
    Internet Section:
    Internet Connection Tab -> Connect Using: Ethernet, Ethernet WAN Port: Automatic (Default), Connection Sharing: Off (Bridge Mode)
    TCP/IP Tab -> Configure IPv4: Using DHCP, IP Address: 10.0.1.2, Subnet Mask: 255.255.255.0, Router Address: 10.0.1.1, DNS Server(s): 10.0.1.1  (Everything else under this tab is blank)
    Hope this helps with info needed.

  • Can you pass multiple files to Business Catalyst at the same time?

    I need to pass information from a client. The infromation is split into several files. I can not access the files to combine them to send as one document to BC. Can I send the two files over even though they do not full fill the necessity of all the user information. File 1 is the personal information and has no other details. When this fill crosses over BC accepts with no trouble. When the second file goes across the personal information is not there but the form details are and this file wipesout the DB. Going through debug when the first file executes I see the data on the BC side. When the second file executes the data is all gone. I cannot combine both files to create one document. Files do not have the same number of users so import of file with file helper would not work since it needs to meet certain requirements to process correctly everytime. By combining the two files would give a different number of tabs than what file helper is looking for and by that matter the data may not be in the correct order. Retrieving the data from the file also would not work since I would have to retrieve from both files at the same time and there would be issues if the user does not occur on both files.
    Please help.
    Thank you,
    Carlos

    Wilderness08 wrote:
    To save time with videos that are not critical, can you capture one video to Premiere Pro at the same time you are authoring to Encore a previously captured video?
    The short answer is yes.
    I have just done that and I am happy to report that it worked like a charm.
    I captured from a DVCAM tape via firewire using PPro CS6 while authoring a Blu-ray disk in Encore CS6.
    No frames were lost during capture and my test blu-ray project was completed without a hitch.

  • How can i delete all songs on my ipad at the same time?

    How can I delete all songs on my ipad at the same time without affecting my library on itunes?

    Use IMAP Mail e.g. Gmail

  • Can you capture 1 video and author another at the same time?

    To save time with videos that are not critical, can you capture one video to Premiere Pro at the same time you are authoring to Encore a previously captured video?

    Wilderness08 wrote:
    To save time with videos that are not critical, can you capture one video to Premiere Pro at the same time you are authoring to Encore a previously captured video?
    The short answer is yes.
    I have just done that and I am happy to report that it worked like a charm.
    I captured from a DVCAM tape via firewire using PPro CS6 while authoring a Blu-ray disk in Encore CS6.
    No frames were lost during capture and my test blu-ray project was completed without a hitch.

  • How can i use both Windows and Mac os at the same time on my iMac

    How can i use both Windows and Mac os at the same time on my iMac

    You can use Parallels desktop or VM Fusion to run both operating systems at the same time. Both programs work well, but I personally perfer VM Fusion.

  • How can I install one app on multiple iPads at the same time?

    We have a volume purchasing account, but when purchasing an app we get multiple serial numbers that all seem to need to be entered individually. The iPhone config Utility will not sync multiple iPads at the same time. Am I missing something? This cannot be the method for mass deployment, it seem too complicated.

    You can do a  backup of you iPad then restore the backup to many devices.
    How to use multiple iPods, iPads, or iPhones with one computer
    http://support.apple.com/kb/HT1495
    Mobile Device Management Solutions for iOS
    http://www.apple.com/iphone/business/integration/mdm/
    http://www.apple.com/ipad/business/resources/
    "iOS mobile device management (MDM)
    With an unmatched breadth of features, a Self Service console forover-the-air (OTA) distribution of in-house and app store apps, and integration with Apple's Volume Purchase Plan (VPP), the Casper Suiteallows administrators to easily achieve the four major tenets of iOSmobile device management: Inventory, Configuration, Security Management, and App Distribution."
    http://jamfsoftware.com/products/casper-suite/

  • Mac Pro can't running two fire wire hard disks at the same time .

    Mac Pro can’t running any two fire wire hard disks at the same time . which two hard disks have extra power from power socket . If i just insert one of them .No problem . If connect two Hds at the same time. Leopard cant find it and the Hds seem no problem. the machine must be restarted and then use one . No problem . I have formated the HD many times .even if which format is Fat 32 or Mac issue persists .Boot from installation CD used the disk utility . Issue stills . If i used one fire wire HD that get power from power socket and used one fire wire device . Leopard was no problem during this time . Whether is this design problem or my machine hardware problem?My Mac has been changed the logic board by Apple service . Do you have similar case in here????

    I connect both hard disks that get power from power supply normally. Also have ever changed the format as GUID. Which always use the power cord . I felt confusion why the issue just happened connect both hard disks with extra power at the same time. If i used one hard disk connect to firewire port . Another firewire port connect other firewire device . No problem at all.

  • Can you use more than one computer to edit the same Premiere Elements Project?

    I am using Premiere Elements 10.  I have built a new project on my desktop computer because the desktop has a firewire port to capture video from my camcorder and my laptop doesn't have a firewire port.  The project is stored on my home network.  I seem to be able to do editing fine using the desktop computer that the project was created on, but it won't load up right on the laptop for editing.  Premiere Elements is configured the same on both computers.  I guess my question is - does Premiere Elements store something on on the computer that the project was created on that is not being stored on the network drive?    How can I fix the problem so that I can edit on my laptop? The laptop is a top of the line Dell XPS with an i7 processor that I use for other Premiere projects, so the laptops ability is not an issue.
    Thanks
    Bill

    Yes, having files stored on a HDD, but having the letter change between machines is a problem. The Project file (PREL) is only an XML database, with links to the Assets. Those links are Absolute Paths, so if anything changes, from drive letter, to file name, the link is broken.
    I have over a dozen externals, that I use to migrate Projects between my main two computers. Each has had its drive letter set in OS of each computer. I started with Z:\ and worked down. Each drive has a lable on it with the designated drive letter. Unfortunately, I ran out of letters, as the workstation has a ton of HDD's and burners, so I had to start over. That does mean that I cannot have both Z:\ drives plugged in at the same time, but that has never been an issue. I wish that Windows would allow for double drive letters, say ZZ:\, but still, I have a handful of letters to use - just too many externals for those letters...
    Happy editing,
    Hunt

  • Can you use a roaming network and wireless extender at same time?

    Greetings community - I've been struggling with an attempt to extend my wireless network for some time now. Please forgive my ignorance on the topic - I realize how 'simple' this is for many of you.  Let me summarize:
    What I have functioning:
    1. Comcast telephony modem
    2. 5th gen Airport Extreme as main wireless router connected to modem via Ethernet (corner of floor 3)
    3. 2nd gen Airport Express as wireless extender (hooked to a stereo on floor 2)
    What I want to accomplish:
    1. I have poor wireless signal on my sun porch (corner of floor 1 opposite side of building as modem)
    Extra equipment I have:
    1. Another 5th gen Airport Extreme
    2. Another 2nd gen Airport Express
    What I have tried (and failed at):
    1. Initially I set up the second Airport Extreme as a second wireless extender and placed it at a further point away than my first wireless extender.  I quickly realized that set up does not function appropriately and one cannot connect to the further extender (I read about that on the apple forums).
    2. I tried placing the second Airport Extreme in a different part of the house at equal distance from the main router as the first wireless extender.  It's capability to extend was minimal if any.
    3. I tried connecting the Airport Extreme to the main router via an Ethernet cable with the hopes of creating a roaming network (which I read about on the apple forums). I would have to come up with a way to run the Ethernet through the house but I'm willing to cross that bridge later.  Once I got that set up, the 2nd gen Airport Express which was previously set up as a wireless extender is no longer recognized. Argh!!
    Questions/Theories/Suggestions:
    1. Is it possible to have a wired extender (via Ethernet) function at the same time as a separate wireless extender all connected to the same router?  If so how do I do it?
    2. I thought about keeping Airport Extreme #1 wireless connected to Airport Express #1 and call that Network 1.  Then plug Airport Extreme #2 directly into the modem to create Network #2 and use Airport Express #2 as wireless extender.  When I tried plugging both Airport Extremes into the modem, they both stopped functioning.
    3. Do I get a second modem to put somewhere else in the house and use Airport Extreme #2 and Airport Express #2 in that fashion?  My guess is Comcast will try to charge me a separate internet access fee to do that (boo!!).
    I know there are a lot of brilliant folks out there.  I'm sure someone can read this and see the 'obvious errors' in my ideas and attempts.  I'm certainly open to new suggestions as well. 
    Thank you in advance for your time and advice.
    - The New Guy

    Is is possible to rename the AEx 2 a different network name from the AEx1 and AE 1 (even though they are all connected to each other)? And say it is possible, would that potentially preventing the jumping?
    No, in extend wireless the names must be the same..
    However since you are creating a network on AE2 which is extended by AEx2 then you can indeed use a different name.. but it must be both,, AE2 and AEx2.
    2. Even more crazy - if I did (could) give the AEx 2 a different network name, could I use my AE 2 as a wireless extension to that second network?  Or is this just getting out of hand now?
    You have lost me now.. there are ways and means.. but let me recommend a better solution.
    Use EOP (homeplug in US) adapters if you cannot run ethernet. Multi-storey houses where you have heavy concrete construction are never going to work well with wireless alone. You are much better getting ethernet properly installed (which is the only 100% guaranteed method).. or buy a set of EOP adapters and give them a try.. they work in some cases and not others.. but better than wireless when they do work.
    Otherwise I think you need higher power wireless routers.. but I can suggest you do the setup in a more controlled manner.
    In other words do not use auto as per the airport utility.. use very short wireless names, different for both bands.. and fixed wireless channels.. then test which band works better.. Then you can do a link.. which will be slow but might give you better performance.
    So..
    Link1 Main AE1---- AEx1 This is wireless extend.
    Link2 AEx1--ethernet--AE2. AE2 is in bridge mode and is also set to create a wireless network. (Use different wireless name here to prevent confusion).
    Link3 AE2-----AEx2 Second wireless extend.
    This overcomes the Apple limitation on multiple extends. It is not great setup but might get wireless to where you need it.. And better speed than you can get now.
    NOTE>. I would personally never do this.. I will run ethernet forevermore.. having tried and tried in various places and using all kinds of equipment.. my conclusion is.. wireless is not suitable.. unless you can get enough signal in from one AP.. everything behind it must be ethernet.
    It is much more expensive in some cases.. but ethernet works.. nothing else can be guaranteed to work.

  • Can you use more then one micro photo on the same comput

    i have had my micro photo for a year it works great i just bought another one but my computer wont recognize it. what gives?they are the same player zen micro ohoto 8 gigs

    It should work fine. Both my Microphoto's work connected on XP Pro at the same time, I just have to keep track of which one has what kind of music. Have you tried scanning for plug and play devices, what kind of operating sys are you running? And what software are you trying to sync with.
    Message Edited by VRevolution on 05-23-200706:45 AM

  • Perfect Keyboard Question!!  Using 2 Bluetooth Keyboard in ios5 at the same time

    Hello People,
    As a Retailer, I love CRM (customer relationship Management) Systems, and I've a software team that programs HTML5 based crm solutions for us.. Why HTML5, because of ipad 2 of course...
    ok Technical question! ready?
    Can ipad use 3 bluetooth HID keyboards at the same time?  you'll ask why?
    Problem is
    We're planning to use Motorola Symbol CS3070 Barcode Scanner http://www.youtube.com/watch?v=tzIbRJiQD24
    And at the same time Apple wireless keyboard for desktop http://www.youtube.com/watch?v=0PBswYZ2JBs
    So the problem is ipad 2 reconises CS3070 as HID keyboard! Wualla
    Can it be done?  P.S : There is no escape key on CS3070
    If this can not be done, i'll be forced to use all-in one pc 's which are heavy and not mobile...
    And also this will be a problem when i am mobile with the barcode reader and ipad since again there will be no on-screen keyboard.
    Thanks
    Now thats ipad crazy idea

    By the way Correction!!!  CS3070 has an disconnect button so it works as it is with the on screen keyboard. connection time is perfect 2 seconds, but disconnection time is 20 seconds on my ipad 1, so do you think ipad2 or future ipad 3 will be faster to disconnect thank you

  • Can i use a track pad and mouse at the same time

    can i use a track pad and a mouse at the same time

    If you mean can you have them both connected at the same time, then it's a yes. I have both connected and use the mouse for some functions and the trackpad for others... works a charm.

  • Can you have Firefox and IE browsers both at the same time and if so, do you have the choice of choosing one for a default browser?

    I am using IE Explorer now presently. I want to be able to download and install the SEO Blogger tool from Wordtracker but it says that I have to have Firefox as the browser. Since I have everything else already set up under IE, I don't want to have to change all that just so I can download one program.
    Can you help?
    Thanks,
    David Craig

    You can have both browsers installed and running at the same time. You can also choose what one to have as the default browser.

Maybe you are looking for

  • Sequence number in ADF FORM.

    hi All, I have a table with ID as primary key and have a sequence created for this primary key and have a trigger for generating sequence number while inserting the record in table. How can i map this Sequence in ADF so while inserting record from Fo

  • MBP switches spaces when returning from screen saver

    When I move my finger minimally across the touchpad to bring my screen out of screen saver, invariably my MBP decides to shift spaces to the next to the left or right. It is annoying.

  • How to get the local date time value

    Hi, I am Australian time zone. I have been using the below code to retrieve meeting start date time from my Sharepoint Calendar. Console.WriteLine((DateTime)oListItem["EndDate"]); This used to return the correct local date up until today. I simply re

  • Custom subtotal

    Hello GURUs Here is my issue. No one has been able to solve this. I have two columns: Parent Company Limit (column A) , and Child Company Limit (column B) The subtotal of column B is actually not the REAL limit of the Parent (the sum of children don'

  • Triggering Java Script in WebDynPro

    Hi Experts, I wanted to know if there is any way to trigger java Scripts in webDynpro application. If yes, please provide any document on the same. Thanks in advance. Regards, Rohan