Cancellation of Billing Invoice

Hi,
I want to put a check in my system that untill and unless the J1IIN doc is cancelled,we cannot cancel VF01 doc.Is there any user exit/check for this?
Kindly guide
Regards
Somnath

Dear Somnath
Yes apply user exit MV50AFZ1 through which your requirement can be met.
thanks
G. Lakshmipathi

Similar Messages

Restrict if the excise invoice isn't cancel we can't cancel the billing Doc

HI
How to Restrict if the excise invoice is not cancel we can't cancel the billing Document
I know if the billing document is Cleared we can restrict by using the copy control Requirement in VOFA (29)
Is it possible to Standard SAP ? if Yes how?
Regards,
Prasanna

Dear prasanna_sap,
It is not possible in standard SAP.
You have to go for a development.
Exit RV60AFZZ-USEREXIT_NUMBER_RANGE
Please find the logic
If XVBRP-WERKS = J_1IWRKCUS - J_1IWERKS Pass the XVBUK - VBELN to J_1IEXCHDR u2013 RDOC, If STATUS = R the document should not allow saving (Error message: Excise invoice to be cancelled first), else allow saving.
Please let me know if you have any further clarifications.
Thanks&Regards
Raghu.k

SD Billing - Avoid Cancellation Creation if Invoice has not been posted yet

Dear all,
I have noticed this problem in my company system.
Problem descripion:
- you creates an invoice and the system doesn't post it for any reason
- then you create the cancel of the invoice, BEFORE forcing the posting of the invoice
--> user creates Cancel, Cancel is not posted as well.
--> from now it is impossible to post both invoices: if you try to post the Invoice after the cancel creation, the VF02 recongnise that a CANCEL exists and do not allow for the posting
--> standard VFX3 doesn't signal this kind of not posted documents situation.
Ok, The right procedure for thes user should be: create invoice, if not posted then try to understand why not posted, and not CANCEL it.
But in this case VFK3 was not able to detect the invoice was not posted: it was not in the list.
So the 2 ways must be:
1) one possibility could be undestand in VFX3 could be enhanced: I checked in OSS but I didn't find anything.
2) other possibility: add a further check in interface between SD and FI in order to check if original invoice is not posted to FI and in this case block the cancel creation, as instead standard SAP does.
Could you please give me an idea on how it would be better proceed?
Thank You very much.
Raffaella

Dear,
thank you for your feedback.
in VOFA the flag is not ticked.
The problem was that In VFX3 no data were found for the specified document (with all "Inclomplete Due To" check box flagged), even if invoice and relative cancel were already created, but not posted.
When we tryied to to post them, via VF02 for example, the system didn't warned anything specific and, doing the posting via debug, we discovered that the posting was stopped because VBRK-RFBSK = E = "Billing Document Cancelled".
So, forcing via debug that value = ' ', because of the urgency of Finance Office, we could invoice it and then do the same for its cancel.
So at the moment it is not possible for me to reproduce the error in the system.
The only workaround I can imagine, is to find a way to avoid cancel creation if invoice is not posted yet.
Do you think this is feasible way?
Thank You veyr much for your suggestions.
KR
Raffaella
Edited by: Raffaella Sacchetto on Nov 29, 2010 3:43 PM

Cancellation of billing document with out cancellation of excise invoice

Dear Sir,
I want to control the cancelation of billing doccument. Condition is that with out cancellation of excise invoice there should not be any cancellation of billing document and delivery document.
REgards
Bharat

You can try with Routines
Create a routine (can take the routines no 5 / 6 as reference to create the new routine and mention not to cancel the billing doc if it is referenced to create any excise invoice) and assign the same in the required billing type definition.
Thanks
Harikishan

When canceling the billing document it carries the invoice referance as "V"

Hi,
When we cancel the billing document using VF11 it carries the invoice reference as "V". we need to change this and we need to take the original invoice document number as the invoice reference. Pls advice how to do this.
Thank you in advance!
Regards
Keshi

Hi
Check with your SD Consultant. This can probably be achieved through Copy Controls routine for the cancellation document type in SD. You will have to adjust your copy control routine accordingly.
Regards
Sanil Bhandari

To not allow billing cancellation when the invoice is cleared

Hello
I would like to know if there is any way to avoid the cancellation of an invoice via VF11 when the invoice has been already cleared.
Thanks in advance.

You can write a user exit by checking the status of accounting document associated with the billing document.
Pl give points if you find my answer helpful / points to correct direction / resolves.
Thanks,
Ramesh

Auto cancellation of excise invoice while cancelling commercial invoice

Dear Experts,
we have done for one of our client that when they create commercial invoice,excise invoice accounting is also getting created. But when i am cancelling the commercial invoice,excise accounting is not getting reversed. Pls suggest measures so that when we cancel the billing doc.excise accounting docs should automatically get reversed .
Also suggest appropriate note if it needs to be applied.
Thanks,
AKD

Hi
Hope these OSS notes are of useful
Note 551932 - Cancellation of Billing with Excise invoice
1081187 Automatic cancellation of excise invocie in billing
regards

Cancel the excise invoice in Intra company stock transfer

Dear Gurus,
I have one issue in CIN.
The following are the my sequence of operation.
Intra company stock transfer.
1. Purchase order with UB. (from plant A)
2. Delivery ( from plant B),
3. PGI ( from plant B),
4.Excise Invoice ( from plant B to A),
5. Billing ( from plant B),
6. Creating Excise Invoice without purchase order Manually (from plant A),
after PGI and Before MIGO.
7. MIGO.
Now i want to cancel the Excise invoice in Plant A.
how can i cancel the excise invoice.?
kindly provide the valid information.
Thanks.
Best Regards
Anbu

In T.Code: J1IIN, there is an option of deleting / cancelling the Excise Invoice. On the top most left hand side (after entering the Excise Invoice number) select Excise Invoice --> Cancel / Delete.
Here it is possible to cancel the Excise Invoice.
Regards,
Rajesh Banka

Cancel the Excise Invoice.

Hi,
I created the Billing document and Excise Invoice. When i went to the Document flow in the Billing Document I found the Accounting document of the Excise Invoice and its status is Cleared.
After that I Cancelled the Excise Invoice. And again I checked the Document flow in the Billing document. But the status is showing the same.i.e Cleared.
Wt it mean..is it correct?
regards,
jyothi.

It is correct. the cancellation of excise invoice wont affect the document flow of sales document. For status go to J1ip enter the invoice no or billing doc and enter. here u can see reversed in the status.
Hope it clarifies ur doubt.
anya

Cancel down payment Invoice and accounting document without lines item

Dear masters,
I have a problem with down payment invoice cancel. As you know when doing invoice down payment request, after release to accounting, the accounting doc will have special G/L indicator is F (noted item). And when I cancel this billing down payment and after release to accounting, the accounting doc of cancel invoice will not have any lines item. Now I want to have lines item for cancel down payment, how can I do that? I really appreciate your support!
Regards,
Nguyen Pham.

Dear Nguyen,
As i understand your process you created Downpayment Request from SD.
Then created Downpayment with reference to that request.
Then you generated Billing invoice and released to accounts.
After that you cleared the downpayment with the Billing document.
Now you want to cancel all this.
First cancel the downpayment by FBRA reset and reverse.
Then cancel the billing document.

After cancelling the billing document accounting document not generated

hi,
we released the billing and accounting document generated but customer needed changes in the billing values so we cancel the billing document but accounting document not generated(reversal accounting not happen)....in document flow it shows in cancel document in blocking state ....we try to release in VF02 but it throws the error "Client 200 does not contain an active application area" . but the other sales order we test in qulaity server the scenorio is working fine...............for specific one sales order creating problem now.....
try to solve the issue ..
Thanks
Muthuraman.D

Dear all,
I have noticed this problem in my company system.
Problem descripion:
- you creates an invoice and the system doesn't post it for any reason
- then you create the cancel of the invoice, BEFORE forcing the posting of the invoice
--> user creates Cancel, Cancel is not posted as well.
--> from now it is impossible to post both invoices: if you try to post the Invoice after the cancel creation, the VF02 recongnise that a CANCEL exists and do not allow for the posting
--> standard VFX3 doesn't signal this kind of not posted documents situation.
Ok, The right procedure for thes user should be: create invoice, if not posted then try to understand why not posted, and not CANCEL it.
But in this case VFK3 was not able to detect the invoice was not posted: it was not in the list.
So the 2 ways must be:
1) one possibility could be undestand in VFX3 could be enhanced: I checked in OSS but I didn't find anything.
2) other possibility: add a further check in interface between SD and FI in order to check if original invoice is not posted to FI and in this case block the cancel creation, as instead standard SAP does.
Could you please give me an idea on how it would be better proceed?
Thank You very much.
Raffaella

I cancelled the billing doc through VF11 Fi document not yet creted

Pls help on this issue.
When i cancelled the billing doc through VF11 Fi document not yet creted. system thrown the given below error:
                                                                                Diagnosis   :                                                                          The document does not exist. It was possibly not posted and therefore cannot be read from the database.
Procedure :
     Repeat the transaction at a later time.
Pls help on this issue.I assign full marks .
Rgds
Mahesh

First check whether accounting posting has been made for your Invoice or not.If accounting document has been created then go to VOFA and check the "Invoice cancellation" field and not the Document type field.
For your billing type F2, Invoice cancellation billing type should be S1 in the standard system.
Document type field is for creation of accounting document type in FI. When you create F2 type of billing document, then DR type of accounting document should be created in FI.
If this "Document type" field is blank than whatever may be the Billing type ,when it is released to accounting , RV type of document will be created.
Regards
Pradyumna

Change payment terms in billing invoice

Hi Gurus,
I have created a billing invoice and I need change its payment terms. In the transaction vf02 (Billing Invoice Change), the field payment terms is disable and it is impossible to change its value.
Is it possible to change the payment terms in a billing invoice???
XeviG.

Xevi,
Please note you will NOT be able to change TOP in billing doc..even if you change as indicated above in sale order it will not reflect in current doc,you have to cancel all the subsequent document after the sale order and then change the TOP as you require in sale order and then process.
Regards
Anil

How to stop cancellation of cleared invoice?

Currently the SAP SD system is allowing the users to cancel the cleared invioce, which is not according to the companies business policy.
How can I stop that, if user try to cancel the cleared invoice system should give an error message and stop.
I am using standard billing type "F2" for invoice and "S1" for cancellation.
I have also checked the "Copying control: Billing document to billing document" but could not find any control which is
Target "S1" AND Source" F2".

Hi
In VOFA for your billing type ( not in copy controls ) in the cancellation tab assign Routine 029 in copying requirements
This will make sure a cleared invoice does not get cancelled
Regards
Raja

Cancellation of billing document through VF11

Cancellation of billing document through VF11

Step 1: Creation of billing document and booking revenue
Entry Passed: Credit Revenue
                          Debit Customer
Step 2: Creation of excise invoice through J1IIN.
Entry Passed: DR Excise Duty Paid
                          CR Cenvat Payable
Step 3: Cancellation of excise Invoice through J1IIN
Entry Passed: DR Cenvat Payable
                         CR Excise Duty Paid
Step 4: Cancellation of billing document through VF11
            Debit Revenue
                  Credit Customer
DR Cenvat Payable
                    CR Excise Duty Paid
So you can see that while canceling procedure the system has passed twice
the reversal of the excise duty i.e in STEP 3 and STEP 4, and because of
this GL balances where not matching. So to counter that we passed a
Financial JV (FB50) and made the Cenvat payable account as NIL on 31st March
2009 but the same did not got reflected in report S_ALR_87012277. It still
shows me a Credit Balance in the CENVAT Payable account

Cancellation of Billing Invoice

Similar Messages

Maybe you are looking for