Cannot access BIOS on Tecra M11-11K after Supervisor password has been set
Hi there,
I've got 10 laptops Toshiba Tecra M11-11K here and they all have the same problem. If they turned on and I enter the BIOS to make adjustments for the first time, it's fine but if I want to return to BIOS after couple of restart (or even one), what happens when I press F2 is that the screen flashes and computer restarts. It does it on all 10 laptops. Anyone knows what to do with that? Flashing BIOS means I have to setup all of them before I can do that, which is a bit of a drag and I don't have guarantee it's gonna work. :/
Thank you,
J
Nope.
When I removed the notebook from the box, I entered the BIOS to change the BOOT order (Network First), setup Supervisor Password and changed SATA to Compatibility mode. Then I saved changes and rebuild the notebook from a WDS.
When done I wanted to change the boot order to HDD only but everytime I press F2 to enter BIOS, the screen only flashes with a blank screen, and computer restarts and I'm back at the Toshiba logo (the one you see when you turn on computer) and that is happening everytime I press F2 to enter BIOS.
It only restarts and comes back with Toshiba logo. Press F2, it restart and Toshiba logo is up again. :/
I tried to update BIOS, but no luck.
I can enter the BIOS only once, when unpacked from the BOX. After that, no chance. 10 laptops have the same problem.
Model Toshiba Tecra M11-11K (PTME0E).
Similar Messages
-
Why my home wifi connection ipad2 enter the password after the password has been wrong? Password is the phone able to connect after the connection is ipad2 has been an error?
Hello joe2616,
Thanks for using Apple Support Communities.
To troubleshoot this issue where your Wi-Fi network is dropping, please follow the directions outlined below.
Symptom: The network connection drops unexpectedly
Your Mac may not not stay connected to your Wi-Fi network reliably.
Your Mac may stop accessing the Internet during use.
Solution
Use these steps if your computer disconnects from its Wi-Fi network unexpectedly.
Check your range to the Wi-Fi router and reduce the effect of interference.
If your computer is too far from your Wi-Fi router or your environment has too much Wi-Fi interference, then your computer may not detect the Wi-Fi network properly. The easiest way to check for range limits with your Wi-Fi network is to move your computer or your Wi-Fi router closer together and make sure that there are no obstructions (such as walls, cabinets, and so forth) between the router and your computer.See Potential sources of wireless interference for more information about interference and solutions.
Try connecting to a different Wi-Fi network. If your computer works fine when connected to a different Wi-Fi network, then the issue may be related to your network router or ISP. In that case, contact the manufacturer of your router or your ISP.
Wi-Fi: How to troubleshoot Wi-Fi connectivity - Apple Support
Thanks for using the Apple Support Communities!
Cheers,
Alex H. -
Cannot Access BIOS or Boot Windows 8 After Changing UEFI BIOS to Legacy BIOS
Acer V7-751, 500G HD, Windows 8.
I changed the BIOS settings from UEFI to Legacy BIOS when I was working on a problem. Now I can't even get into the BIOS (F2)
or change the Boot Order (F12). All I get is an error "Operating System not found". I can boot with a Win7, Win8, or Win8,1 DVD. I suppose I could boot with just about anything else bootable as well.
The problem seems to be caused because it's set to Legacy BIOS and Secure Boot Manager as default #1 boot device. Legacy BIOS
can't boot a Win8 drive that has been installed under UEFI (Secure Boot). I have to change the BIOS back to EUFI to boot the WIn8 drive, but the only way to change the BIOS is from within Win8. It's a very flawed way of doing things but it's the way it is.
Does anyone have any suggestions that they KNOW work. Please don't Google answers. I've already done that. And please (please)
don't tell me to power on and press "F2" (or any other key) to go into BIOS. If I could do that I wouldn't be posting.
Once again, I cannot get into the BIOS without going into Windows first. I cannot load Windows because the install was done
under UEFI. I cannot change from Legacy to UEFI because I can't get into the BIOS.In this case, I flashed the BIOS with a newer version of the BIOS/Firmware and that returned everything to the Defaults (not Legacy BIOS). I believe you could also flash with the same version. I don't think you could flash with an earlier version, but no harm
in trying it. if you've flashed the BIOS previously, you may be able to restore the previous copy. It all depends on the manufacturer and how they handle flashing the BIOS.
I wasn't able to, but you may also be able to boot from a correctly formatted USB drive with another OS (Windows XP/Vista/7) because Legacy BIOS allows you to boot from external devices. Essentially, you need to be able to boot from a valid OS that is not on
the Hard Drive that was configured using the UEFI BIOS setting.
Please let me know if you have any more questions, and I'll do what I can to help. If this solves your problem, please mark my post as the answer. Thank you. -
Unable to log in after account password has been reset by email with tokens ect ect ect
ugh, getting frustrated trying to retrieve an old skype account, from the email message below to the email account it was registered to this would suggest the skype account still exists. After going to the page and changing my password i go try logging into skype and it fails to log me in sucessfully i have submitted 2 web form requests to skype customer support to "look into this issue" several weeks ago, i've yet to hear back from either request (the reply isn't being blocked by my bulk email provider or in my spam folder... i have searched the skype support page while logged in with a 2nd account but cannot find a "live chat" link to speak with customer support, suggestions appreciated. --------- Forwarded message ----------
From: Microsoft account team <[e-mail removed for privacy and security]>
Date: Fri, Jul 10, 2015
Subject: Microsoft account password change
To: ***********@********.com
Microsoft account
Your password changed
The password for the Microsoft account *******@*******.com was just changed.
If this was you, then you can safely ignore this email.
If this wasn't you, your account has been compromised. Please follow these steps:
1. Reset your password.
2. Learn how to make your account more secure.
To opt out or change where you receive security notifications, click here.
Thanks,
The Microsoft account team
>>>>---------- Forwarded message ----------
From: Microsoft account team <[e-mail removed for privacy and security]>
Date: Fri, Jul 10, 2015
Subject: Microsoft account password reset
To: ********@******.com
Microsoft account
Password reset code
Please use this code to reset the password for the Microsoft account *********@********.com.
Here is your code: ************
If you don't recognize the Microsoft account ********@*******.com, you can click here to remove your email address from that account.
Thanks,
The Microsoft account teamTry it again and keep checking your email, it also depends on how fast your Internet is because, I used to have a really slow Internet connection thing and it would take hours or even a day!! If you have another apple product like phone, or iPod see if you can go on there and try it. I'm not that advanced with this stuff but it works for me!
-
Can't log into Game Center even after my password has been reset Help please
I have 2 gamecenter accounts, I tried logging into one last night but its telling me to reset my password which I have done but its still saying wrong password. Any ideas on what I should try next please? Oh I have a ipad 2 and all my software is up to date thanks
Can anyone help please I have been able to download apps send and receive emails.. Just not log into Game Center has anyone got any idea what is going on please. Both Game Center accounts are on the same devise but that has been working up until now.....
-
Tecra M11-11K intermitent wireless signal
Hello all,
Just wondering if anyone has had issues with a Tecra M11-11K running on Windows 7 professional 64bits latest service pack.
In this one the wireless tends to disconnect sporadically, no matter how clean the signal is to the WAP, or what kind of encryption. All other machines work just fine and it has the same behaviour when it's using public or closed hotspots...
We also tried using the latest drivers supplied by Intel, to no avail.
The machine has also had a clean system install.
Any clues or advice would be greatly appreciated.Hi
Did you try to disable the power saving feature?
The Win 7 power management provides different options in order to save the battery power.
So this can affect the Wlan functionality.
Please check the Win 7 power management and disable the power saving for Wlan.
Furthermore you can go to device manager -> Wlan card -> Advanced tab and could check the available options.
I cannot say exactly what options are available because this depends on the Wlan card. -
HP Pavilion DV6-3029tx Cannot Access BIOS Setup
Hello there, I have used this laptop for nearly two years, if I remember correctly.
Basically, the problem is that I want to disable Function key, but I cannot access BIOS setup.
I have tried every combination of keys at start-up screen, from ESC to F10, none of them worked.
So I thought maybe an BIOS update can solve the problem (My current version is F.07), I downloaded firmware from HP support site and run it, know what, the screen flashed and system get restarted, but nothing had changed, I didn't get even an error message.
The problem is actually found by a HP supporter when I send my laptop for cleaning last year, he didn't manage to fix it at the time and problem became devastating for me lately because certain software I am using rely heavily on function keys. The only things "big" I have ever done to my laptop were updating windows 7 Home to Ultimate (32-bit) and partition, I am not sure if they were the reason.
The following is InsydeFlash log, I searched the error code and find somebody with similar problem here: http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and/Pavillion-DV6-3125er-BIOS-UPDATE-Error/t...
--- Log started: 2012/04/18 17:30:15
Initializing...
Log file : I:\SwSetup\SP55299\InsydeFlash.Log
Settings file : I:\SwSetup\SP55299\platform.ini (found)
Executable : I:\SwSetup\SP55299\InsydeFlash.exe
Version : 4.0.4.0 Build : InsydeFlash
Date : Fri Oct 15 14:25:12 2010
Resource file : I:\SwSetup\SP55299\iscflash.dll (loaded)
App name : InsydesFlash
OS Information : Microsoft Windows 7 Service Pack 1 - supported
Preparation stage
IHISI Version : 193
Error code : 3010(0x00000BC2)
Cleanup Stage
Stage Completed
--- Log Stopped: 2012/04/18 17:30:16
--- Log started: 2012/04/18 17:38:11
Initializing...
Log file : I:\SWSetup\SP55299\InsydeFlash.Log
Settings file : I:\SWSetup\SP55299\platform.ini (found)
Executable : I:\SWSetup\SP55299\InsydeFlash.exe
Version : 4.0.4.0 Build : InsydeFlash
Date : Fri Oct 15 14:25:12 2010
Resource file : I:\SWSetup\SP55299\iscflash.dll (loaded)
App name : InsydesFlash
OS Information : Microsoft Windows 7 Service Pack 1 - supported
Preparation stage
IHISI Version : 193
Device Name:\Device\HarddiskVolume1
SearchVolumeFileAndCreateDirectory
Device Name:\Device\HarddiskVolume3
SearchVolumeFileAndCreateDirectory
Device Name:\Device\HarddiskVolume4
SearchVolumeFileAndCreateDirectory
Device Name:\Device\HarddiskVolume5
SearchVolumeFileAndCreateDirectory
Device Name:\Device\HarddiskVolume7
SearchVolumeFileAndCreateDirectory
Sign File Name:\\?\Volume{5ab76131-9b4b-11df-90b9-c80aa990af36}\\Hewlett-Packard\BIOSUpdate\HpBiosUpdate.sig
Sign File Name:\\?\Volume{5ab76131-9b4b-11df-90b9-c80aa990af36}\\Hewlett-Packard\BIOSUpdate\HpBiosUpdate.EFI
Device Name:\Device\HarddiskVolume2
SearchVolumeFileAndCreateDirectory
Device Name:\Device\HarddiskVolume6
SearchVolumeFileAndCreateDirectory
Device Name:\Device\CdRom0
Device Name:\Device\CdRom1
Allow Version: B.0D, Dex: 2829
Current Version: F.07, Dex: 3847
Current BIOS version is bigger than the version setted in Ini.
Partition : 1 WMI 0x0D: 1
Check Package : 1
BIOS sign : 1
File sign : 1
Processing parameters...
Image file : I:\SWSetup\SP55299\01448F29.bin
Backup file : No Backup file
OEM ID : 0x103C
Loading new BIOS image file...
Opening file I:\SWSetup\SP55299\01448F29.bin
Not sign file
g_dwEcSize : 0x00080000
Reading 4194304 bytes from file starting at 0 ...
BIOS image size : 4194304 (0x00400000)
ECSize : 0x80000
Error code : 3010(0x00000BC2)
Cleanup Stage
Stage Completed
--- Log Stopped: 2012/04/18 17:38:20
Thanks for your help.Nevermind, I deleted the HP_TOOLS partition and problem solved, this may help those who have similar problem.
-
I cannot access iphoto to include an attachment after upgrading to Mavricks
I cannot access iphoto to include an attachment after upgrading to Mavricks but the picutures are all there in iphoto.
Please help!You don't have this feature in your new mail window
where you can drag and drop the picture of your choice into the email window?
OT -
How do I get into iTunes to access Netflix, when I get "iTunes unable to connect until time has been set", after submiting my password?
You need to follow the instructions in this article that best apply to your situation:
Forgot passcode for your iPhone, iPad, or iPod touch, or your device is disabled - Apple Support
If you do not have a backup in either iCloud or iTunes, then you will have no way to retain the information on your device because you will have to restore it in order to access it again.
Sorry,
GB -
Cannot create a session after the response has been committed (Tomcat 6)
I'm getting a rather annoying error when I try to open a pretty basic JSP page.
I'm rather new to the whole JSP scene, so I'm following the example found on pages 287 and onwards in "JSF in Action - Manning" in case anyone wanted to check my code against the source.
I've searched for about 4 hours now, coming back to this site a couple of times, once reading about writeouts and stuff. But I'm not really sure this is the issue in this case and if it is, where exactly the problem lies.
I've already fixed a number of errors I got (jtsl.jar and standard.jar missing etc...) but this particular problem is driving me (and my co-workers for that matter :-) ) up the wall.
Anyone willing to help me out here?
Error:
description The server encountered an internal error () that prevented it from fulfilling this request.
exception
javax.servlet.ServletException: Cannot create a session after the response has been committed
javax.faces.webapp.FacesServlet.service(FacesServlet.java:152)
root cause
java.lang.IllegalStateException: Cannot create a session after the response has been committed
org.apache.catalina.connector.Request.doGetSession(Request.java:2301)
org.apache.catalina.connector.Request.getSession(Request.java:2075)
org.apache.catalina.connector.RequestFacade.getSession(RequestFacade.java:833)
org.apache.myfaces.context.servlet.SessionMap.setAttribute(SessionMap.java:53)
org.apache.myfaces.util.AbstractAttributeMap.put(AbstractAttributeMap.java:103)
org.apache.myfaces.util.AbstractAttributeMap.put(AbstractAttributeMap.java:35)
org.apache.myfaces.application.jsp.JspStateManagerImpl.saveSerializedViewInServletSession(JspStateManagerImpl.java:523)
org.apache.myfaces.application.jsp.JspStateManagerImpl.saveSerializedView(JspStateManagerImpl.java:358)
javax.faces.application.StateManager.saveView(StateManager.java:47)
org.apache.myfaces.application.jsp.JspViewHandlerImpl$StateMarkerAwareWriter.flushToWriter(JspViewHandlerImpl.java:387)
org.apache.myfaces.application.jsp.JspViewHandlerImpl.renderView(JspViewHandlerImpl.java:322)
org.apache.myfaces.lifecycle.RenderResponseExecutor.execute(RenderResponseExecutor.java:41)
org.apache.myfaces.lifecycle.LifecycleImpl.render(LifecycleImpl.java:132)
javax.faces.webapp.FacesServlet.service(FacesServlet.java:138)
Source Code of login.jsp:
<%@ page language="java" contentType="text/html; charset=ISO-8859-1"
pageEncoding="ISO-8859-1"%>
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN" "http://www.w3.org/TR/html4/loose.dtd">
<%@ taglib uri="http://java.sun.com/jsf/core" prefix="f"%>
<%@ taglib uri="http://java.sun.com/jsf/html" prefix="h"%>
<f:view>
<html>
<head>
<title>
<h:outputText value="ProjectTrack"/>
</title>
</head>
<body>
<table>
<tr>
<td>
<h:graphicImage url="/images/logo Skillteam.jpg"
alt="Welcome to ProjectTrack"
title="Welcome to ProjectTrack"
width="435" height="120"/>
</td>
<td>
<font face="Arial, sans-serif"
size="6">
<h:outputText value="ProjectTrack"/>
</font>
</td>
</tr>
http://forum.java.sun.com/post!default.jspa?forumID=45#
Click for bold </table>
</body>
</html>
</f:view>
web.xml & faces-config
<?xml version="1.0" encoding="UTF-8"?>
<web-app xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns="http://java.sun.com/xml/ns/javaee"
xmlns:web="http://java.sun.com/xml/ns/javaee/web-app_2_5.xsd"
xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/web-app_2_5.xsd" id="WebApp_ID" version="2.5">
<display-name>ProjectTrack</display-name>
<welcome-file-list>
<welcome-file>faces/login.jsp</welcome-file>
<welcome-file>index.html</welcome-file>
</welcome-file-list>
<servlet>
<servlet-name>Faces Servlet</servlet-name>
<servlet-class>javax.faces.webapp.FacesServlet</servlet-class>
<load-on-startup>1</load-on-startup>
</servlet>
<servlet-mapping>
<servlet-name>Faces Servlet</servlet-name>
<url-pattern>/faces/*</url-pattern>
</servlet-mapping>
</web-app>
<?xml version="1.0"?>
<!DOCTYPE faces-config PUBLIC
"-//Sun Microsystems, Inc.//DTD JavaServer Faces Config 1.0//EN"
"http://java.sun.com/dtd/web-facesconfig_1_0.dtd">
<faces-config>
<navigation-rule>
<from-view-id>/login.jsp</from-view-id>
<navigation-case>
<from-outcome>success</from-outcome>
<to-view-id>/inbox.jsp</to-view-id>
</navigation-case>
<navigation-case>
<from-outcome>failure</from-outcome>
<to-view-id>/login.jsp</to-view-id>
</navigation-case>
</navigation-rule>
</faces-config>Setup:
Eclipse Europe 3.3.0
Tomcat 6.0.13
MyFaces 1.2
JRE 1.6.0_02When searching for this error, this was the first page google gave me. I found the answer and just in case anyone else stumbles in here with the same question I thought I'd share my findings.
Unfortunately, if your problem is the same as mine, you're going to feel pretty silly. I was navigating to the wrong page. If MyFaces(when running tomcat) tries to resolve to a page that doesn't exist, the error given above is what happens.
In my case I accidentally put my .jsp page into the wrong directory and ended up banging my head against the wall for an hour figuring that out. Hope this helps someone. -
I am running safari 7.0.6 with IOS 10.9.4. after the mac has been asleep and I log on I cannot open safari as it appears to have crashed. the workaround to this is to reboot the IOS and log back in after which safari will open. Any ideas on how to resolve this?
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
For this step, the title of the Console window should be All Messages. If it isn't, select
SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar at the top of the screen.
In the top right corner of the Console window, there's a search box labeled Filter. Initially the words "String Matching" are shown in that box. Enter the name of the crashed application or process. For example, if iTunes crashed, you would enter "iTunes" (without the quotes.)
Each message in the log begins with the date and time when it was entered. Select the messages from the time of the last crash, if any. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
☞ The log contains a vast amount of information, almost all of which is irrelevant to solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
☞ Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
In the Console window, select
DIAGNOSTIC AND USAGE INFORMATION ▹ User Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of crash reports. The name of each report starts with the name of the process, and ends with ".crash". Select the most recent report related to the process in question. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
I know the report is long, maybe several hundred lines. Please post all of it anyway.
If you don't see any reports listed, but you know there was a crash, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report—they're very long and rarely helpful. -
Hi, I cannot access my gmail from my iphone. The password is correct and I can access fine from my computer but the iphone keeps telling me the password is incorrect. Any ideas?
I believe Gmail has an option for Two-Step verification that may require a different password for mobile devices than for your computer.
https://support.google.com/mail/answer/2703311?hl=en -
Is there a way to see what font was used originally, after the type has been converted to outlines?
Hi all, I would really like to know if there is any way to find out what font was used originally in an Illustrator document, after the type has been converted to outlines? The reason for this is I need to update some wording in a couple of old logos I had made and I have NO idea what font I had used...for the life of me I just cannot remember. Because this was so urgent for one of my projects I had to do a search online via "WhatTheFont" to see what font it could be (which I then didn't seem to have in my library!), and repurchase it. I am 99% sure I HAVE the font - or something VERY close - but under a different name.
Normally I keep a much better record of fonts used but there have been times occasionally in the past when I have done something in a hurry and changed the type to outlines without keeping the original, or keeping detailed notes at least. The fact that I did NOT keep notes on a few projects I have done in the past has made me want to kick myself because now I need to revisit one of those again..grrr:)
Can anyone offer any advice? I appreciate your help as always:)
best,
ChristineChristine,
You can also ask in the Typography forum,
http://forums.adobe.com/community/design_development/typography?view=discussions&start=0
The guy running whatfontis is a regular poster there.
And apart from
http://www.whatfontis.com/
there are
http://www.identifont.com/
http://new.myfonts.com/WhatTheFont/
and especially for script,
http://www.bowfinprintworks.com/ScriptIDGuide.html -
I was working on Setting of my iphone4S, and there was an option ''Zoom''. I made it enable and there after whole screen has been 10 times larger. Now I can Not do anything, even can't open my phone anymore because I can't see the sliding option due to extra large screen. Please help me.
Did you try to tap using three fingers?
Turn Zoom on or off. Go to Settings > General > Accessibility > Zoom. Or, use the Accessibility Shortcut. See Accessibility Shortcut on page 123.
Zoom in or out. Double-tap the screen with three fingers.
copied from page 134 of the user guide iOS7 -
in setting up new apple tv, message says "apple tv cannot sign in to Itunes until network time has been set - please try again later.........is this an easy fix?
Welcome to the Apple Community.
Assuming this is not the first time you have used your Apple TV
You might try restarting the Apple TV by removing ALL the cables for 30 seconds.
Also try restarting the router.
If the problem persists, try a restore, you may want to try the previous procedures several times before doing this.
If restoring from the Apple TV doesn't help, try restoring from iTunes using a USB cable.
If this is a new Apple TV, in addition to trying the above, it may also be that your network router is not allowing access to the timeserver, check that your router allows access over port 123.
Maybe you are looking for
-
Questions on Scheduling and Running an Agent and Scenario
Hi, I have created a scenario and I want to schedule it to run. Is it possible to schedule and run it using an agent but having no Repository? Thanks, Randy
-
HT3529 Issue with messaging and icloud after ios7.1 update. Need Help!!!
My husband and I have been having problems with our iphone 5c since the ios7.1 update. We can't seem to send messages to each other now without incurring data charges, because our icloud messaging seems to have both phones synced to my itunes account
-
Adobe Reader XI won't launch/read pdfs. No error message.
All of a sudden, reader xi wont launch, read pdfs, or download pdfs online. When I double click the program shortcut (or pdf I want to open) the mouse makes the "loading" animation....but nothing happens. No error message, just refuses to work. Re-in
-
I am the administrator of my MacBook Pro, which I share with my kids. One of them forgot his password, so as the admin I changed it for his account, but when I try to see his account, it says I need to provide the keychain password. How can i get it
-
How to add blank table for exisiting PDF?
Hi team, I have a PDF which is to display data in a queue order.But i am not sucessful in that case. So for my solution i need to have a blank table in starting page (I mean 1st).So i have no idea how to edit and add a new table to exisiti