Cannot Access Routers Web Based Page?

I have a wireless Linksys router Model WRT54G and it will not let me access my routers web based page. When I enter the default IP address into the Address Bar nothing happens (I've checked to make sure my router is on the default IP), i just get a blank screen, no pop-up or anything. Help?

Note that the router's "web pages" are built into the router. You do not need to be connected to the Internet to see them.
To view the router's web pages:
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Check to see if your "modem-router" is using the same 192.168.1.x address space as your Linksys router. If it is, then report back with this problem, and also state the make and model of your modem-router.
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
If the reset does not fix your system, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.

Similar Messages

Cannot access routers web-set up page.

I recently changed my ISP from Verizon to Cox. I can access the internet when my router is NOT connected. When I connect my router I gain Local access but no internet. I can't access my routers web-set up either. I tried to contact Cox but they do not offer help with routers. Can someone please help me with this problem?
My router is WRT54G V2
My modem is Arris TM602G
Running window vista ultimate

As you have changed your ISP you should first reset your router and then re-configure it...Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router using the link here...

Is there a way to access the web-based setup for my router if I cannot access the internet?

Okay, I need to change the ip address settings on my router. I have a WRT54G Wireless router. I cannot access the internet on my computer connected to the router, and do not know how to change the router settings without accessing the web-based setup page. So, back to my question. Is there a way to access this page if I cannot connect to the internet?

On the back of the router is a small reset switch. Using a paper clip or other small item, press the switch in and hold it for a few seconds. This will reset the router to the default IP address of 192.168.1.1. Enter that address in your web browser, and be sure your computer is attached to the router by an Ethernet cable. Don't attempt to do this using the wireless connection.
Once you have reached the web configuration utility you can change the DHCP settings.
To give your PC a static IP address you will need to open your network connections panel and, assuming your using Windows XP, make the changes from dynamic IP to static there.

Cannot Access IP Web Browser Configuration Page OfficeJet 8600 Plus

Win 7 64-bit
HP OfficeJet Pro 8600 Plus
Wireless Connection
Hi:
The printout of wireless network test page shows IP address for HP Officejet Pro 8600 Plus as: http://192.168.1.104 (The HP Home Network Diagnostic Utility v4.3.0.002 also shows: 192.168.1.104)
When I try to access http://192.168.1.104 with either IE 9 or Firefox 10 I get an error message: "The website is unable to display the webpage"
But, on the same computer I CAN access http://192.168.1.103 HP Officejet 6480 web browser configuration page with either IE 9 or Firefox 10
Why I can't access the web configuration page: http://192.168.1.104
Thanks
FYI: I set the router to various other network modes, channel widths, channels and ssid broadcast on/off, and also removed power from router and printer, reconnected power and restarted computer, all these efforts did NOT allow access to http://192.168.1.104
This question was solved.
View Solution.

On the front of the printer: Setup > Network > Wireless Setup Wizard. Run it.
Next, on your PC, delete all instances of your printer in Control Panel > Devices and Printers.
Finally, re-add the printer this way:
1. Make sure the printer is turned on and connected to your network. Verify that you can access the printer's internal web page by browsing to its IP address before continuing. Get its IP from a Network Test printed from the front panel of the printer.
2. Click >> Start >> Control panel >> Devices & Printers.
3. Click the Add a printer
4. Select Local printer
5. Select Create a new port and select Standard TCP/IP Port and click Next button.
6. Under Device type, select TCP/IP Device. Under Hostname or IP address, enter the printer's IP address. Click Next.
7. Select Hewlett-Packard from the list of manufacturers and select and select your printer model. Click Next.
If your printer model was not listed, then select Have Disk, browse the HP CD that came with your printer and select the first file that starts with hp and ends with inf. Click Open then OK. Select your printer model. Click Next.
8. If you are asked, use the currently installed driver.
9. It will ask for the Printer name -- enter a new name or use the existing one. This will be the name of the printer that you select from other applications.
10. You may be asked to share the printer. Choose NO.
11. The Print Test Page box appears. Go ahead and print it.
12. Click Finish.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

How do I access the web-based utility

I just purchased a wireless router...WRT300N. I want to access the "web-based utility" in order to update the firmware.
How do I access the web-based utility...help!
Thanks.

Access the router’s web-based setup page.
For instructions, click here.
Linksys Easy Answer 4030, applies to WRT300N
Upgrading the Linksys Router's Firmware
Hope this helps,
Lilla
Westell 6100 modem/router; Linksys WRT54GL v1.1 router firmware 4.30.9; Linksys WPC54G v2 Notebook Card; CenturyTel DSL using PPPoE

Error: "Cannot access the web server" with BlazeDS Turnkey

Help! I'm new to Flex and BlazeDS and Eclipse. I was trying to setup a Flex Project using a BlazeDS/Tomcat server running from Eclipse on Windows XP per the example in flexbandit.com/archives/55#comment-269 and in (www.infoq.com/articles/blazeds-intro).   I am NOT using the Eclipse Flex plug-in. I'm using Flex Builder for the Flex code.
Here's what I've done:
I installed BlazeDS and tested http://localhost:8400 - That worked.
I setup Tomcat in Eclipse. - That seemed to work.
I created a Dynamic Web Project in Eclipse - That seemed to work.
I created the bare-bones BlazeDS Configuration under the Eclipse project and then created a basic HelloWorld java class.
I added the destination in the “remoting-config.xml” file found in the c:/projects/workspace/ReportGenTool/WebContent/WEB-INF/flex” directory:
<destination id="HelloWorld">   <properties> <source>HelloWorld</source> </properties> </destination>
When I started the application server by clicking on the server's green play button in Eclipse and then tried to open localhost:8400/ReportGenTool, I got the 404 error : The requested source (/ReportGenTool/) is not available which according to the instructions is fine.
Next I created a Flex Project, but when I try to validate the new Flex project configuration, it gives me an error "Cannot access the web server. The server may not be running, or the web root folder or root URL may be invalid."
When I validated the server was running after setting up the BlazeDs Turnkey, I saw the BlazeDS page.
Now when I bring up http://localhost:8400 I get:
      Directory Listing for /
      Apache Tomcat/6.0.14
My eclipse project is named ReportGenTool and I've overwritten the WebContent directory with the META-INF and WEB-INF directories from the BlazeDS installation (C:\blazeds\tomcat\webapps\blazeds). According to Eclipse the server is running.
My Flex project is named ReportGenTool and is located in another directory away from the Eclipse project directory.
     My root folder is: C:\Projects\workspace\ReportGenTool\WebContent
     Root URL: is http://localhost:8400/ReportGenTool/
     Context root is: /ReportGenTool/
Any idea what might be wrong? What didn't I configure that needs to be configured?
Thanks in advance.

This is not working because your router has a direct to your web server that is not through the outside interface which is needed for nat to occur, for this to work you need to setup a loopback interface as nat outside and policy route traffic to there for your server traffic
Bu if your server is internal why do you need nat at all? Can you not use bind with views that might be simpler
M
Sent from Cisco Technical Support iPad App

Cannot access Oracle BAM Start Page

Although Oracle BAM installation completed without any error and I can start BAM related services without any issue, I cannot access Oracle BAM Start Page because of the following error.
You are unable to connect to the Oracle BAM services. Contact your system administrator if the error persists. [ErrorSource="ActiveDataCache", ErrorID="ADCServerConnectionError"] The requested name is valid, but no data of the requested type was found [ErrorSource="mscorlib"] Debugging information: Oracle.BAM.ActiveDataCache.ServerUnavailableException: You are unable to connect to the Oracle BAM services. Contact your system administrator if the error persists. ---> System.Net.Sockets.SocketException: The requested name is valid, but no data of the requested type was found Server stack trace: at System.Net.Dns.GetHostByName(String hostName) at System.Net.Dns.Resolve(String hostName) at System.Runtime.Remoting.Channels.RemoteConnection..ctor(SocketCache socketCache, String machineAndPort) at System.Runtime.Remoting.Channels.SocketCache.GetSocket(String machineAndPort) at System.Runtime.Remoting.Channels.Tcp.TcpClientTransportSink.SendRequestWithRetry(IMessage msg, ITransportHeaders requestHeaders, Stream requestStream) at System.Runtime.Remoting.Channels.Tcp.TcpClientTransportSink.ProcessMessage(IMessage msg, ITransportHeaders requestHeaders, Stream requestStream, ITransportHeaders& responseHeaders, Stream& responseStream) at System.Runtime.Remoting.Channels.BinaryClientFormatterSink.SyncProcessMessage(IMessage msg) Exception rethrown at [0]: at System.Runtime.Remoting.Proxies.RealProxy.HandleReturnMessage(IMessage reqMsg, IMessage retMsg) at System.Runtime.Remoting.Proxies.RealProxy.PrivateInvoke(MessageData& msgData, Int32 type) at Oracle.BAM.ActiveDataCache.Common.Core.IDataStore.Exists(String strDatasetID) at Oracle.BAM.ActiveDataCache.Remoting.ServerWrapper.Exists(String strDatasetID) --- End of inner exception stack trace --- at Oracle.BAM.ActiveDataCache.Remoting.ServerWrapper.Exists(String strDatasetID) at Oracle.BAM.ActiveDataCache.SystemType.LoadSchema(Boolean bCache) at Oracle.BAM.ActiveDataCache.Context.LoadUser() at Oracle.BAM.ActiveDataCache.Context..ctor(String strDomain) at Oracle.BAM.Web.WebPage.CreateContext(String strUserName) at Oracle.BAM.Common.Threading.SynchedHash.GetObject(String strKey, Object oLock) at Oracle.BAM.Common.Threading.SynchedHash.GetObject(String strKey) at Oracle.BAM.Web.WebPage.GetContext() at Oracle.BAM.StartPage.StartUp.Initialize()
Do you have any idea ?
Although I checked ActiveDataCache.log, it is empty ( looks no problem ).
My environment as below.
OS : Windows 2003 R2 Enterprise Edition Service Pack 1
Oracle version : 10.1.0.2
Oracle BAM version : 10.1.2
Thanks in advance

Hi,
I've installed BAM 10.1.2 on Windows 2000 Professional. I have IIS 5.0 and Microsoft 1.1 .Net Framework installed on my PC. I'm able to use the Design Studio and Admin from Oracle BAM Enterprise Link. The installation completed successfully but I'm still not able to open the BAM start page.
I see the error:
Server Error in '/' Application.
Configuration Error
Description: An error occurred during the processing of a configuration file required to service this request. Please review the specific error details below and modify your configuration file appropriately.
Parser Error Message: It is an error to use a section registered as allowDefinition='MachineToApplication' beyond application level. This error can be caused by a virtual directory not being configured as an application in IIS.
Source Error:
Line 263: 
Line 264: 
Line 265: <authentication mode="Windows">
Line 266:
Line 267: </authentication>
Source File: C:\OracleBAM\BAM\web.config Line: 265
I've checked that OracleBAM appears as a virtual directory in IIS (from Personal Web Server) and there were no errors in installation. The Access Permissions is set to 'Read' and Application Permissions to 'Scripts'
Should the authentication mode take any other parameters ?
Let me know what can be done to resolve this issue.
Thanks in advance !

Since I updated my IPad software to iOS 5.0.1 from 5.0, I cannot access some web sites. Hoy can I go back?

Since I updated my IPad software to iOS 5.0.1 from 5.0, I cannot access some web sites. How can I go back?

Sorry, you cannot downgrade iOS software.
First thing to try is a reboot of your iPad. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider until the Apple logo appear. Let go of the buttons and let the iPad restart. See if that fixes your problem.

How can the DFF created for a PO form be used in PO web based page.

Hello,
I have created a DFF on the PO form using the attribute2 of the PO_HEADERS table. How can I create a DFF on the web page based 'buyer work center' page. My final goal is to use DFF for both the web based pages and forms.
Thanks for your help
Raj

hello Pradeep,
Whats the difference b/w DFF and custom DFF ?
I'll tell the steps what I did.
1. Application Developer > Flex Field > Descriptive > Register
Registered a DFF for PO_HEADERS_ALL table and used Attribute2.
2. Application Developer > Flex Field > Descriptive > Segments
So I used the DFF in the PO form. I want to see a DFF in the PO page also when the below navigation is used.
Purchasing: >Buyer Work Center>Orders. Opens a PO page.
Thanks for the help.
Raj

Can't Access the web administration page

Hello,
I have a new Linksys router that I installed a few months ago. I am trying to connect my PS3 using wireless. the PS3 sees the access point SSID, but keeps failing to connect. I have double/triple check the WEP2 key and it is correct. I am also having problems accessing the web administration page. I keep getting page not found. I don't think that I have access the web administration page since I set it up. I can ping the router, so I know that its up, along with getting out to the Internet, I have used NMAP and scanned the router, but only 10080 is open (PS3) port. I assume that the default URL for the web administration page is http://192.168.1.1. There is no port needed to put in the URL is there? Also, since NMAP showed no ports open does that mean that the web server in the router is not listen? If so how do I connect without having to reset the router?
I do have some Cisco Linksys app that shows a GUI of my network, but no adminisration help.
Thanks,

Who is your ISP..?
Are you able to go online on the wired computer...?
Make sure the computer is connected to the router on the Ethernet port and check the ip address first...Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...
If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security softwares on the computer...
If you get 4 replies then,Adjust the browser settings....Open an IE, click Tools >> Internet Options, then delete all files, cookies, history, forms...Goto "Connections", make sure Never Dial a Connection is checked, click on LAN Settings and make sure all the options are unchecked...Once you are done click on O.k...Close the IE and re-open it...
Now,try to open the setup page again...

Trouble printing e-mail and web based pages

I have a Envy 4500 all in one. Can't print body of e-mails and some web based pages from myToshiba laptop. It will print fine from my I-Phone using e-print. Do I need to enable a setting somewhere?

Hi
Printing from websites is sometimes tricky. Have you tried using SmartPrint?
http://h41112.www4.hp.com/smartprint/us/en/smart.html?jumpid=ex_r602_ww/en/hho/ipg/xx-mu-aw_chev/sma...
Although I am an HP employee, I am speaking for myself and not for HP.
Twitter: @Ciara_B_HP

Cannot access acrobat web capture facility too busy

Hi, i
have been using adobe acrobat 9 (part of creative web suite cs4) to convert webpages to pdf's. I now get a message to say that 'cannot access acrobat web capture facility too busy. I have reinstalled the software and ran the repair tool in acrobat after reading similar issues on the forum. It still hasnt fixed it. Any ideas??

I don't know what happened to acrobat V9 - I have the same problem - sorry I am at a loss?
Ron

Firefox 9.0, I cannot access Netflix web sight, but I can access it with IE, tried clearing cache & cookies stil cnnot access Netflix.

I use Firefox 9.0, I cannot access Netflix web sight, but I can access it using IE, I tried clearing the cache & cookies, but I still cannot access it. Help.

Try looking at [[Error loading web sites]] first.

Cannot access Linksys Wireless GUI Page after DHCP disabled.

Ok funny situation I have here... I have another main wired router, and a Linksys WRT54GS Wireless Router. I want to use the Linksys as an access point since my smoothy has DHCP server enabled. So, I disabled DHCP on the linksys, set the router IP as 192.168.0.2 (my smoothy is 192.168.0.1). I also put the connection from the main router to the Linksys on the LAN ports, not WAN. I reset everything and my computers and everything works fine. The DHCP works properly from my main router, I get Internet etc. HOWEVER, I cannot access the Linksys GUI page when I go to 192.168.0.2...it just times out! Any ideas? I can access it if the DHCP is enabled on the linksys, but with it off I cannot. Thanks!

try assigning a static ip add on the computer ( 192.168.1.3 ) .. connect it to the router and then try to access http://192.168.0.2

Cisco WS-SVC-NAM-2 Upgrade to 6.0.2; cannot access management web page

I upgraded our WS-SVC-NAM-2 which resides on a 6500, from version 5.1.2.1 to 6.0.2, to include patch2 . Everything seemed ok, however, regardless if I enable http or ip http secure server enable, we cannot access the management site with eithrer FireFox or IE. Status bar shows Internal 500 error, in FF shows "Problem Loading Page" The connection to the server was reset while the page was loading. I'm wondering if it has anything to do with Java, or crypto keys? Here are the patches loaded:
Mon May 4 11:51:20 2009 Patch: nam-app.4-0.strong-crypto-patchK9-1-0 Description: Strong Crypto Patch for NAM.
Fri May 6 08:56:59 2011 Patch: nam-app.strong-crypto-patchK9-5.1-0 Description: Strong Crypto Patch for NAM.
Fri Oct 7 06:53:20 2011 Patch: nam-app.strong-crypto-patchK9-5.1.2-1 Description: Strong Crypto Patch for NAM.
Wed Oct 15 14:56:28 2014 Patch: nam-app-patch.6.0-2-patch2 Description: Patch 2 for NAM release 6.0(2)
Successfully enabled web server.
[email protected]# show version
NAM application image version: 6.0(2-patch2)
Maintenance image version: 2.1(5)
NAM Daughter Card Micro code version: 1.34.1.28 (NAM)
BIOS Version: 4.0-Rel 6.0.9
PID: WS-SVC-NAM-2
Memory size: 1024 MB
Disk 0 size: 20 GB
Installed patches:
Any help would be appreciated. Thanks

Hi Ahmed,
****Upgarde procedure keep the Old data and take you you to the New version *******
This is an Upgarde Procedure ,however if you use the --install command during the Upgarde Procedure ,it will wipeout the old data and NAM will be like a factory Installed and then it will upgarded to New Version.
Follow the below link ,in the step 5:
Step 5 Upgrade the NAM application software as follows:
DON NOT USE THIS
root@localhost# upgrade ftp-url
where ftp-url is the FTP location and name of the NAM software image file
or
USE THIS ONE
root@localhost# upgrade ftp-url --install
Note The --install keyword clears and recreates all of the NAM partitions; this action is similar to restoring the factory-default state. If you use the --install keyword, the previously stored reports and data (if any) will be lost.
http://www.cisco.com/en/US/docs/net_mgmt/network_analysis_module_software/5.1/switch/configuration/guide/advcfg.html#wp1035516
IMP :: It is recommended to have 2GB RAM for running 5.x image
Thanks-
Afroz
[Do rate the useful post]

Cannot Access Routers Web Based Page?

Similar Messages

Maybe you are looking for