Cannot access the Inbound Refinery Logs, authentication failed.
I installed the Inbound Refinery as a proxied server on the same computer of Content Server.
When I login Inbound Refinery using 'sysadmin' and try to access the "Logs-Refinery Logs", the authentication dialog appears.
I am sure that I input the right password for user sysadmin here, but the authentication dialog jumps out again and again until the authentication failed.
Who can tell me how to solve this problem? Your help will be very appreciated.
Hi
Well that is not possible since the logs are native to IBR and to access them you need to provide the refadmin access itself. But the other IBR access are with sysadmin since it is added as a proxy server to existing CS instance.
Srinath
Similar Messages
-
Hi,
I am monitoring AD server from SCOM 2012 R2. My management server goes into waning state. When i run Health explorer then it come back in the healthy state but after some time it again goes into warning state. After seeing alert i found that a alert is coming
again and again i.e. Operations Manager Failed to Access the Windows Event Log.The description of alert is mention below
The Windows Event Log Provider is still unable to open the DhcpAdminEvents event log on computer 'nc2vws12ad5.corp.nathcorp.com'.
The Provider has been unable to open the DhcpAdminEvents event log for 64080 seconds.
Most recent error details: The RPC server is unavailable.
Please suggest me how to resolve this so that my management server will again come back in healthy state.
Thanks
AbhishekHi Abhishek,
As i mentioned earlier the Alert resolution says the same points.
Can you give details on the below ?
Is there really a log named "Dhcpadminevents" in the MS's Event viewer ?
Did you recently configure any new alert where you mentioned "Dhcpadminevents"
as a event log location ?
If yes then what is the target you selected for the rule / monitor there ?
Can you post the results for analysis ?
Gautam.75801 -
Recurrent error in Win32 install logs (The process cannot access the file..
hi forum !
I'm already on my third installation of Hyperion Essbase and still getting the same error within the logs :
(Jan 31, 2008 1:48:29 PM), essbaseServer7_0_0Suite, com.installshield.wizard.platform.win32.WindowsSharedFiles, err, ServiceException: (error code = -30016; message = "The process cannot access the file because it is being used by another process.
(32)"; severity = 0)
STACK_TRACE: 23
ServiceException: (error code = -30016; message = "The process cannot access the file because it is being used by another process.
(32)"; severity = 0)
at com.installshield.wizard.platform.win32.Win32FileServiceImpl.win32SetFileModified(Native Method)
at com.installshield.wizard.platform.win32.Win32FileServiceImpl.setFileModified(Win32FileServiceImpl.java:115)
at sun.reflect.GeneratedMethodAccessor272.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source)
at java.lang.reflect.Method.invoke(Unknown Source)
at com.installshield.wizard.service.LocalImplementorProxy.invoke(LocalImplementorProxy.java:52)
at com.installshield.wizard.service.AbstractService.invokeImpl(AbstractService.java:51)
at com.installshield.wizard.service.file.GenericFileService.setFileModified(GenericFileService.java:185)
at com.installshield.product.actions.Files.setFileTimes(Files.java:1608)
at com.installshield.product.actions.Files.install(Files.java:460)
at com.installshield.wizard.platform.win32.WindowsSharedFiles.install(WindowsSharedFiles.java:87)
at com.installshield.product.service.product.PureJavaProductServiceImpl.installProductAction(PureJavaProductServiceImpl.java:1916)
at com.installshield.product.service.product.PureJavaProductServiceImpl$InstallProduct.getResultForProductAction(PureJavaProductServiceImpl.java:5195)
at com.installshield.product.service.product.InstallableObjectVisitor.visitComponent(InstallableObjectVisitor.java:369)
at com.installshield.product.service.product.InstallableObjectVisitor.visitInstallableComponents(InstallableObjectVisitor.java:333)
at com.installshield.product.service.product.InstallableObjectVisitor.visitProductBeans(InstallableObjectVisitor.java:133)
at com.installshield.product.service.product.PureJavaProductServiceImpl$InstallProduct.install(PureJavaProductServiceImpl.java:4563)
at com.installshield.product.service.product.PureJavaProductServiceImpl$Installer.execute(PureJavaProductServiceImpl.java:3758)
at com.installshield.wizard.service.AsynchronousOperation.run(AsynchronousOperation.java:41)
at java.lang.Thread.run(Unknown Source)
can use the products but this shouldn't be fine... do I have to stop a service or grant some permission ? any help is appreciated.
thanks & regards,not having any JAVA_HOME env var. Did some checkings and :
- one machine was having Java libraries because of DB2
- the other machine was a fresh Win2003SP1 with SQL Server 2005
guess can set JAVA_HOME to C:\Hyperion\common\JRE\Sun\1.5.0 before installing Essbase, but also guess it's a documented/automatic step... wonder what I'm missing ?
doing the most basic-mode installations (defaults, automatic deployments), once I get them clean will perform more sophisticated ones. Searched the 9.3.1 doc PDFs without useful findings. -
I cannot get my iMac with built-in airport wi-fi to allow internet connections to Nook and PS3. The devices access the network, but internet connection fails. Internet sharing is enabled, network security (WEP, WPA) is disabled. What to check next?
On an additional note, I've purchased a wireless router and everything connected on the first attempt. It just vexes me that the built-in wireless isn't working as a router. Is this another example of "Mac only plays with Mac"?
-
I have a quick question for you and it would be great if you can answer me on this.
I'm working through SharePoint Workflow issue (developed using Nintex) that started recently where people are getting workflow error and I don't see issues if I submit it myself. Current error. - "Failed to start workflow. The workflow cannot access
the item that it has been applied to."
I haven't made any major changes to Workflow except for changing email notification content and publishing it. My question is, do I need to publish the rest of the workflows too that are associated to the list after I publish changes of one workflow? Looks
like users have required permissions to submit the form. Please let me know how to get rid of this error.
smithHi Smithspd,
According to your description, my understanding is that your users got a workflow error, and the workflow is created by Nintex.
For SharePoint Designer workflow, once we do any change in a workflow, we need to re-publish the workflow.
For your issue, I suggest you re-publish the workflow, compare the result.
In addition, as your workflow is created by Nintex and this forum is for SharePoint Designer, I suggest you ask Nintex support or forum for better help. Thanks for your understanding.
Best Regards,
Wendy
Wendy Li
TechNet Community Support -
I use www.talktalk.co.uk/mail as my email account. I have 2 computers. One runs Windows XP and Firefox 3.6.18 - and that one works just fine with talktalk webmail. The other machine runs Windows Vista and until the past couple of days used Firefox 3.6.18. Within the past couple of days I have changed to Firefox 5 on this machine and now, although it still connects to www.talktalk.co.uk/mail just fine, I now get a message "You have undefined new mails in your inbox". I cannot access the inbox, and the Contacts list appears empty (or I cannot access it). This has only happened since I went up toFirefox 5. However, using the same machine (Vista) but using Internet Explorer as the browser, all works perfectly with talktalk webmail. this leads me to think that it is nothing to do with talktalk, but is something that has happened as a result of my going to Firefox 5. I am not very knowledgeable about the workings of computer software, so if you are willing and able to help me, please keep it simple and detailed. I need my hand holding!!
Regards, GeoffYep, exactly the same problem only on W2K SP4. Firefox5 doesn't work but IE (on the same machine) does.
Sorry, I'm not sure what version version of IE is being used.
(It's the PC at work that has the problem and I'm writing this at home on my linux box which has Firefox version 3.6.18 for linux mint - which also works fine.)
I really hope this can be fixed soon.
Andy. -
I am working with a client who is attempting to backup to a NAS device
The device is a linksys NSS6000 (Cisco device).
It’s a dual 1Gbit LAN device that supports CIFS / FTP and NFS transfers. It has only 1Gbit lan connected.
The device has 4 * 500 gb sata drives in raid 1 attached.
Cables go from cat 5 to fiber back to cat5. (The NAS is located at a neighboring office) The switches are 1gbit.
Server is a win2k8r1 fully up to date.
When backing up to the NAS device, the following error occurs:
Running backup of volume Local Disk(D:), copied (86%).
Running backup of volume Local Disk(D:), copied (90%).
Running backup of volume Local Disk(D:), copied (94%).
Running backup of volume Local Disk(D:), copied (98%).
Backup of volume Local Disk(D:) completed successfully.
Backup stopped before completing.
Summary of backup:
Backup stopped before completing.
The process cannot access the file because it is being used by another process.
If we redirect the backup to a folder on a 2008 share, the backup completes successfully.
Only when backing up to the linksys NSS6000 does the error occur.
No other backup processes are writing to the NAS device so I can't understand why the process thinks the file is
being used by another process.
One thing we did notice that when the backup to the NAS device occurs, throughput is about 150 mbit average
On the 2008 server shares we successfully backup to, the through put is 500 mbit. Not sure if that is important, but
might be worth mentioning.
The following event log entry was noted at the end of the backup.
The description for Event ID '519' in Source 'Microsoft-Windows-Backup' cannot be found.
The local computer may not have the necessary registry information or message DLL files to display the message,
or you may not have permission to access them. The following information is part of the
event:'2009-05-12T10:13:31.617Z', '', '2147942432', '%%2147942432'
Any ideas?
Thanks..MichaelI am also seeing the same problem backing up nightly to a brand new NAS device (WD My Book Live)
All the error codes are the same as those in this thread.
From Windows Event Viewer:
The backup operation that started at '2011-03-25T06:00:19.811302700Z' has failed with following error code '2147942432' (The process cannot access the file because it is being used by another process.). Please review the event details
for a solution, and then rerun the backup operation once the issue is resolved.
Fault bucket 659897467, type 5
Event Name: WindowsBackupFailure
Response: Not available
Cab Id: 0
Problem signature:
P1: Backup
P2: 6.1.7600
P3: 0x80070020
P4: 7
P5:
P6:
P7:
P8:
P9:
P10:
Attached files:
C:\Windows\Logs\WindowsBackup\WindowsBackup.1.etl
These files may be available here:
C:\ProgramData\Microsoft\Windows\WER\ReportArchive\NonCritical_Backup_6957d65de91fc4a853ecc7c78914bf7351fff0d1_14578325
Analysis symbol:
Rechecking for solution: 0
Report Id: dd480bf2-56a6-11e0-ae81-00217099bf56
Report Status: 0
From Report.wer in C:\ProgramData\Microsoft\Windows\WER\ReportArchive\NonCritical_Backup_6957d65de91fc4a853ecc7c78914bf7351fff0d1_14578325
Version=1
EventType=WindowsBackupFailure
EventTime=129455071508181139
Consent=1
UploadTime=129455071508201140
ReportIdentifier=dd480bf2-56a6-11e0-ae81-00217099bf56
Response.BucketId=659897467
Response.BucketTable=5
Response.type=4
Sig[0].Name=Operation
Sig[0].Value=Backup
Sig[1].Name=AppVer
Sig[1].Value=6.1.7600
Sig[2].Name=HRESULT
Sig[2].Value=0x80070020
Sig[3].Name=TargetType
Sig[3].Value=7
DynamicSig[1].Name=OS Version
DynamicSig[1].Value=6.1.7600.2.0.0.256.48
DynamicSig[2].Name=Locale ID
DynamicSig[2].Value=1033
State[0].Key=Transport.DoneStage1
State[0].Value=1
State[1].Key=DataRequest
State[1].Value=Bucket=659897467/nBucketTable=5/nResponse=1/n
FriendlyEventName=WindowsBackupFailure
ConsentKey=WindowsBackupFailure
AppName=Windows host process (Rundll32)
AppPath=C:\Windows\System32\rundll32.exe
ReportDescription=Windows Backup failure -
I have a problem with starting the Excel Application under a particular user (service account).
I try to schedule this C# script through an application X (not Windows Task Scheduler. And this
application will always use a service account to run services on the server). If I run the C# script in
command prompt under the same user, it runs. Under the application X, which uses the exact same
user, to initiate the C# script, it fails to open the Excel application (not sufficient permission?).
This script calls application.Workbooks.Open(<ExcelFileName>,0,false,Type.missing....). At this line
of code, it gives the following error:
Microsoft Excel cannot access the file "...". There are several possible reasons:
-The file name or path does not exist.
-The file is being used by another program.
-The workbook you are trying to save has the same name as a currently open workbook.
I tried all the methods that I found online as follow:
Create directory "C:\Windows\SysWOW64\config\systemprofile\Desktop" (for 64 bit Windows) or "C:\Windows\System32\config\systemprofile\Desktop" (for 32 bit Windows).
Changed the DCOM config for the Microsoft Excel application to include this user for Local/Remote Launch and Access.
Enabled all macros in Excel application and set the Trust Center.
Add the user to have full control on all folders that contain the Excel file.
Under DCOM
config, Microsoft Excel Application, if I modify the Identity tab to check on "This User" and enter the username/password to let Excel always run under that user. Then the application runs perfectly. However, other users can't run the excel application
on their own with the following error: "Cannot use object linking and embedding". If I check "Use the launching user", then Excel can't be launched. No errors in the logs or events anywhere to check.
Yet, still the same error. I think it's permission but I am not sure where and what to do for this to work.
Now, normally, when I run this excel report, I can double-click on the file and it'd automatically run,
save the new parameters into the current file and generate a new excel file (with date attached to the
file name). That means there is a change (save) to the original file.
Environment: Windows Server 2008 R2 and running Microsoft Excel 2010.
I appreciate all your help!I am wondering if this has anything to do with having the user log into Excel.
In point #5 above: Under DCOM config, Microsoft Excel Application, if I modify the Identity tab to check on "This User" and enter the username/password to let Excel always run under that user. Then the application runs perfectly. However, other
users can't run the excel application on their own with the following error: "Cannot use object linking and embedding". If I check "Use the launching user", then Excel can't be launched. No errors in the logs or events anywhere to check.
Because running with the launching user proposes an user to run the Excel application. However, I do not think there is any where that we can pass in the password for this user to Excel. However, this Excel has all the permissions to Excel application as
well as the folders that have the Excel files.
Please help!
Thank you! -
Hi,
starting a couple of weeks ago, we get the following error(s) when running applications from a network share. We don't know what causes this, we are not aware of any major changes in our network infrastructure or client/Server configuration. We did upgrade
a lot of machines to Windows 8, but the issue also occurs on older Win7 computers.
We figured out a workaround though: The applications run fine when launching from a FQDN share (like
\\share.domain.Company.com) and only cause problems when running from
\\share directly. They have worked fine for years without FQDN though.
Any ideas?
Error Details (the Kind of error differs greatly):
# 1 #
Log Name: Application
Source: Application Error
Date: ...
Event ID: 1005
Task Category: (100)
Level: Error
Keywords: Classic
User: N/A
Computer: vmDEV
Description:
Windows cannot access the file for one of the following reasons: there is a problem with the network connection, the disk that the file is stored on, or the storage drivers installed on this computer; or the disk is missing. Windows closed the program XYZ
because of this error.
Program: XYZ
File:
The error value is listed in the Additional Data section.
User Action
1. Open the file again. This situation might be a temporary problem that corrects itself when the program runs again.
2. If the file still cannot be accessed and
- It is on the network, your network administrator should verify that there is not a problem with the network and that the server can be contacted.
- It is on a removable disk, for example, a floppy disk or CD-ROM, verify that the disk is fully inserted into the computer.
3. Check and repair the file system by running CHKDSK. To run CHKDSK, click Start, click Run, type CMD, and then click OK. At the command prompt, type CHKDSK /F, and then press ENTER.
4. If the problem persists, restore the file from a backup copy.
5. Determine whether other files on the same disk can be opened. If not, the disk might be damaged. If it is a hard disk, contact your administrator or computer hardware vendor for further assistance.
Additional data
Error value: C000020C [ also seen with code C00000C4]
#2 (German error Messages from now on, we only use German OSes, the above english one is translated based on similar error Messages I found on the web) #
Name der fehlerhaften Anwendung: XYZ.exe, Version: 2015.0.496.5054, Zeitstempel: 0x54ea67c3
Name des fehlerhaften Moduls: clr.dll, Version: 4.0.30319.34014, Zeitstempel: 0x52e0b784
Ausnahmecode: 0xc0000006
Fehleroffset: 0x00026549
ID des fehlerhaften Prozesses: 0x13ac
Startzeit der fehlerhaften Anwendung: 0x01d055a854d36445
Pfad der fehlerhaften Anwendung: \\share\application.exe
Pfad des fehlerhaften Moduls: C:\Windows\Microsoft.NET\Framework\v4.0.30319\clr.dll
Berichtskennung: 949ea933-c19b-11e4-bf04-78542e186754
Vollständiger Name des fehlerhaften Pakets:
Anwendungs-ID, die relativ zum fehlerhaften Paket ist:
Anwendung: XYZ.exe
Frameworkversion: v4.0.30319
Beschreibung: Der Prozess wurde aufgrund einer unbehandelten Ausnahme beendet.
Ausnahmeinformationen: Ausnahmecode c0000006, Ausnahmeadresse 720B6549
Stapel:
# 3 #
Anwendung: WpfApp.exe
Frameworkversion: v4.0.30319
Beschreibung: Der Prozess wurde aufgrund einer unbehandelten Ausnahme beendet.
Ausnahmeinformationen: System.Runtime.InteropServices.SEHException
Stapel:
bei SP.Forms.AutoCompleteSelectionBase.OnEnter(System.EventArgs)
bei System.Windows.Forms.Control.NotifyEnter()
bei System.Windows.Forms.ContainerControl.UpdateFocusedControl()
# 4 #
Anwendung: WpfApp.exe
Frameworkversion: v4.0.30319
Beschreibung: Der Prozess wurde aufgrund einer unbehandelten Ausnahme beendet.
Ausnahmeinformationen: System.Runtime.InteropServices.SEHException
Stapel:
bei System.IO.UnmanagedMemoryStream.ReadByte()
bei System.IO.BinaryReader.ReadByte()
bei System.IO.BinaryReader.Read7BitEncodedInt()
bei System.Resources.ResourceReader._LoadObjectV2(Int32, System.Resources.ResourceTypeCode ByRef)
bei System.Resources.ResourceReader.LoadObjectV2(Int32, System.Resources.ResourceTypeCode ByRef)
bei System.Resources.ResourceReader.LoadObject(Int32, System.Resources.ResourceTypeCode ByRef)
bei System.Resources.RuntimeResourceSet.GetObject(System.String, Boolean, Boolean)
bei System.Resources.RuntimeResourceSet.GetObject(System.String, Boolean)
bei System.Resources.ResourceManager.GetObject(System.String, System.Globalization.CultureInfo, Boolean)
bei System.Resources.ResourceManager.GetStream(System.String, System.Globalization.CultureInfo)
# 5 #
Anwendung: WpfApp.exe
Frameworkversion: v4.0.30319
Beschreibung: Der Prozess wurde aufgrund einer unbehandelten Ausnahme beendet.
Ausnahmeinformationen: System.Runtime.InteropServices.SEHException
Stapel:
bei System.Reflection.RuntimeParameterInfo.get_Name()
bei System.Diagnostics.StackTrace.ToString(TraceFormat)
bei System.Environment.GetStackTrace(System.Exception, Boolean)
bei System.Exception.GetStackTrace(Boolean)
bei System.Exception.ToString(Boolean, Boolean)
bei System.Exception.ToString(Boolean, Boolean)
bei System.Exception.ToString(Boolean, Boolean)
bei System.Exception.ToString()
# 6 #
Name der fehlerhaften Anwendung: XYZ.exe, Version: 2015.0.496.5054, Zeitstempel: 0x54ea834f
Name des fehlerhaften Moduls: KERNELBASE.dll, Version: 6.3.9600.17278, Zeitstempel: 0x53eeb460
Ausnahmecode: 0xe0434352
Fehleroffset: 0x00012f71
ID des fehlerhaften Prozesses: 0xa68
Startzeit der fehlerhaften Anwendung: 0x01d0559cb7ec4ed6
Pfad der fehlerhaften Anwendung: \\share\XYZ.exe
Pfad des fehlerhaften Moduls: C:\WINDOWS\SYSTEM32\KERNELBASE.dll
Berichtskennung: 010514d0-c190-11e4-bf04-78542e186754
Vollständiger Name des fehlerhaften Pakets:
Anwendungs-ID, die relativ zum fehlerhaften Paket ist:
# 7 #
Name der fehlerhaften Anwendung: XYZ.exe, Version: 2015.0.496.5054, Zeitstempel: 0x54ea7a6e
Name des fehlerhaften Moduls: ntdll.dll, Version: 6.3.9600.17630, Zeitstempel: 0x54b0d74f
Ausnahmecode: 0xc0000006
Fehleroffset: 0x0006db27
ID des fehlerhaften Prozesses: 0x18dc
Startzeit der fehlerhaften Anwendung: 0x01d0559cb08529c3
Pfad der fehlerhaften Anwendung: \\share\xyz.exe
Pfad des fehlerhaften Moduls: C:\WINDOWS\SYSTEM32\ntdll.dll
Berichtskennung: ef389186-c18f-11e4-bf04-78542e186754
Vollständiger Name des fehlerhaften Pakets:
Anwendungs-ID, die relativ zum fehlerhaften Paket ist:Hi,
>>The applications run fine when launching from a FQDN share
It sounds like a DNS suffix issue. When this issue occurs, please try to ping share on the client, then check if the corresponding IP address is correct. If the IP address is wrong, please adjust your settings of DNS to make sure that the client can resolve
the share correctly.
If it's very hard to change the settings of the DNS for some reason, as a work around, we can add the entry into the clients' hosts file.
Best Regards.
Steven Lee Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected] -
Hi, guys
I cannot view delegate mailbox in Outlook. Following is my configure.
I have two mailbox A-User and B-User
Login Outlook as A-User, click File -> Account Settings -> Delegate Access, add B-User and give Editor permission of Inbox.
Right click A-User's root inbox and select Properties -> Permission, select B-User and check "Folder visible".
Login Outlook as B-User on other computer, click File -> Account Settings -> Account Settings, select B-User and click Change -> More Settings -> Advanced, add A-User.
Now I can see a root A-User in Navigation Pane. But when I click it, it shows
"Cannot display the folder. Microsoft Outlook cannot access the specified folder location."
or
"Cannot display the folder. Microsoft Outlook cannot access the specified folder location. The operation failed. An object cannot be found".
I searched some solutions from internet, but all of them don't work. Could you give some suggestions?
Thanks.Hi,
First, please double check if you have given the right permission to B-User on your step 2.
In addition, we can try to give a higher permission to the B-user to check the result.
Please feel free to post back and let me know the result.
Best Regards,
Steve Fan
TechNet Community Support -
I often have occasions to run more than one Profile simultaneously (usually because of different add-ons I've installed on different Profiles). In the past this worked fine. Now, all of a sudden, if I open a second Profile while the first is running the second cannot access the Internet until I close the first. It keeps looking for a website, and failing, until the system "times out". If I close the first Profile, the second is then able to access the Internet.
Note: this is not a problem with opening a second Window in Firefox. As long as they are from the same Profile they will both work fine. Nor does this stop me from using a second Profile to look at website files I have saved to my computer. The only problem is that the second Profile cannot get on the Internet.I just checked, the setting was for "Automatic proxy configuration URL", in the past it was set on "No Proxy". So I'll try changing that (and/or try other proxy options), and see if that solves the problem.
If it does, then just one (academic) question remains: why did that happen in the first place? I don't care what the answer is, so long as your suggestion solves the problem.
Thanks. -
Hi,
We are having issues with Server 2012 R2 SMB shares.
We try to write some changes to a file, but we first create a temporary backup in case the write fails. After the backup is created we write the changes to the file and then we get an error:
The process cannot access the file '\\server\share\test.txt' because it is being used by another process.
It looks like the backup process keeps the original file in use.
The problem doesn't always occur the first time, but almost everytime after 2 or 3 changes. I have provided some code below to reproduce the problem, you can run this in a loop to reproduce.
The problem is that once the error arises, the file remains 'in use' for a while, so you cannot retry but have to wait at least several minutes.
I've already used Process Explorer to analyze, but there are no open file handles.
To reproduce the problem: create two Server 2012 R2 machines and run the below code from one server accessing an SMB share on the other server.
Below is the code I use for testing, if you reproduce the scenario, I'm sure you get the same error.
We are not looking for an alternative way to solve this, but wonder if this is a bug that needs to be reported?
Anybody seen this behavior before or know what's causing it?
The code:
string file =
@"\\server\share\test.txt";
if (File.Exists(file))
File.Copy(file, file +
".bak", true);
File.WriteAllText(file,
"Testje",
Encoding.UTF8);
The error:
System.IO.IOException: The process cannot access the file '\\server\share\test.txt' because it is being used by another process.Hi,
There is someone else having the same issue with yours. You could try code in the article below:
“The process cannot access the file because it is being used by another process”
http://blogs.msdn.com/b/shawncao/archive/2010/06/04/the-process-cannot-access-the-file-because-it-is-being-used-by-another-process.aspx
If you wonder the root cause of the issue, the .NET Framework Class Libraries forum can help.
Best Regards,
Mandy
If you have any feedback on our support, please click
here .
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
Both myself and my wife have 2 separate iTunes accounts, I subscribe to iTunes Match. Music purchased on my wife's account appear on our computer iTunes library but my iPad cannot access the music she has purchased. Is there any way to overcome this
The only way to do what you want is to log into your wife's iTunes Store account on your iPad. Doing this will lock you out of your account for 90 days.
-
I go into the 2008 r2 dc and add a user. The 2003 dc has all of the fsmo roles. Then I go into the exchange server and add the new mailbox through the GUI. It runs the cmdlet and creates the new mailbox without any errors. Then I go in and try to access
the mailbox through owa and cannot access the mailbox. It says the mailbox does not exist. Both my 2003 dc(which I want to decommission) and 2008 servers are replicating. I see the user object on both servers. I have the email server pointed to the 2003 dns
server as my preferred dns. This just started happenning a couple of days ago. I dont know if a windows update caused this but everything was fine before Wednesday. All of the other users can access their mailboxes through owa just any new ones I created cannot.
In fact when I send a test email to the new account, I immediately get a bounce back so I dont think I would be able to access the new mailbox through outlook.
visualbasicfrustratedHello,
I recommend you check your exchange server using windows server 2003 DC or windows server 2008 DC.
Please use repadmin /showrepl command to check DC replication status.
Please check if there is related error in application log.
Cara Chen
TechNet Community Support -
I am installing creative the cloud Illustrator desktop app on a machine with windows 7 64 bit running in a domain environment. The download starts and takes about runs for a bout 10 minutes and then stops with the error: DF024: Unable to preserve original file at "C:\Program Files\Adobe\Adobe Illustrator CC 2014\Support Files\Contents\Windows\AdobeLinguistic.dll" Error 32 The process cannot access the file because it is being used by another process.(Seq 1352)
I am logged in as a network administrator and there are no other apps except a web browser (Chrome) running. There are no other users logged into the machine.
How can I see what other process is using the needed file so that I can fix it?
ThanksMelissaB34 it looks like you already are reviewing your installation log files but you can find more information at Troubleshoot install issues with log files | CC - http://helpx.adobe.com/creative-cloud/kb/troubleshoot-install-logs-cc.html. From the error you have posted it appears that your current User account is either unable to update C:\Program Files\Adobe\Adobe Illustrator CC 2014\Support Files\Contents\Windows\AdobeLinguistic.dll or does not have sufficient file permissions to do so. Since you mentioned you are on a domain please ensure that you are working with your I.T. department and have correct access to this directory.
You may want to also consider logging in under a local administrator account to see if you face the same difficulties. This would help you determine if you are facing a file corruption issue or file permission issue.
Maybe you are looking for
-
How do you remove a pc from icloud?
Can't figure out how to remove a compter from icloud so i can free up space to add a new device. Any help would be appreciated.
-
Photo and video editor on nokia n8 belle
Hi, my phone crashed, with a stupid demo game, and I had to use the 3 buttons reset. Now, I do not have access to nokia video and photo editor. How can I reinstall this? Thanks in advance
-
Dear Guru's I have a question regarding LIV and Subsequent Debits. We have a Value Tolerance set of Lower 20% or £50 and upper 2% or £10 (OMR6). I have a Purchase Order for qty 1 Value £1,500. At this point no GR has taken place. In MIRO I create an
-
I understand that to make a custom LAF, all you need to do is extend one of the standard LAFs, but how do you describe how things are to look (and feel)? What I mean is if you want you text fields to have rounded corners, how do you go about having i
-
Determining internal table structure dynamically
Hi, I have a number of internal tables in my program which I declare using types. As an example: TYPES: begin of ty_hierarchy, control_id(6) type c, node_id(10) type c, node_name type bezei40,