Cannot access web using hostname

Hi,
I am not able to access web in hotjava webbrowser using hostname like www.sun.com. But it is possible to access using IP address. I am using solaris 2.6, hotjava 1.0 . I am new to unix. I do not know what to be configured to get it right.
Your help is welcome.

You need to configure some nameing service, like nis,
nisplus or dns. In some networks a nis/nisplus server
can provide name->ip translation; but for a small
standalone system you'll probably need straight dns.
Setup /etc/resolv.conf (see "man resolv.conf"), add your
domainname and some dns servers. Test name lookups using
the nslookup utility.
Then copy /etc/nsswitch.dns to /etc/nsswitch.conf (see "man
nsswitch.conf"). Test name lookups via nsswitch using
getent ("getent hosts www.sun.com").

Similar Messages

NAC GUEST SERVER CANNOT ACCESS WEB CONSOLE

Hello,
I have a NAC guest server. I can access CLI but cannot access web console. I used both the https:// ip address/admin and http://ip address/admin. Please what could be the solution of this issue?
thank you and best regards.
Edwin

Edwin,
Are the various necessary services running on that server? Post the output of following commands:
ps auwwwx
chkconfig --list
service httpd status
service postgresql status
Faisal

How do i solve - cannot access web server - error message when creating a project in 4.5 with PHP

How do i solve - cannot access web server - error message when creating a project in 4.5 with PHP

Screenshot of how it looks when i try to show a ms access form inside a iframe:
http://oi58.tinypic.com/2vj4ish.jpg

SPA122 cannot access web configuration utility

The new SPA122 device connected to router through DHCP.
I can see IP-address on router's web page, can ping it, and receive it with ****110# IVR command.
But I cannot access web configuration utility in the browser: the page is unavailible. I tried to allow WAN access with ****7932#1#1 IVR action - the problrem still on.
Can You give me any advice what to do.

You can also connect to the lan/ethernet side of the device, do an ipconfig /renew
You should get an address on the 192.168.15 network, the default for the router in the ATA is 192.168.15.1
Then you can set up the non default password, enable the wan web server (administration tab I think).
dlm...

Suddenly on my iPad I cannot access web links via emails but can on my iphone

Suddenly I Cannot access web links via emails on my iPad but can on my iPhone. Is there something in my settings I need to change?

Restart
https://www.apple.com/support/iphone/assistant/phone/#section_1

I cannot access Siri using my iphone 5 earphones by pressing and holding down the center button on the earphones?

I cannot access Siri using my iphone 5 earphones provided with my phone. I press and hold down the center button on the earphones, but it doesn't activate Siri.

If you had checked the settings - you might have noticed that Siri isn't in the settings either. Siri is in the settings on the iPad 3, the iPad 4 and on the Mini.

I cannot access updates using my new password it was verified by adobe

I cannot access updates using my new password it was verified by adobe

Since this is an open forum, not Adobe support... you need to contact Adobe staff to help
Adobe contact information - http://helpx.adobe.com/contact.html
-Select your product and what you need help with
-Click on the blue box "Still need help? Contact us"

Cannot access web. Network diagnostics says my internet connection appears to be working correctly

Am running Lion on MacBook. Suddenly cannot access web with Safari or Firefox. Email OK and Network diagnostics says my internet connection appears to be working correctly". No problems with my iMac on same network.

What exactly happens when you try to load a web page?

Cannot access web page anymore

I can no longer access my banks web page anymore. I was able to get to the page and sign in up to a few days ago.
When I try to get to the page I get a message that says "Safari can’t open the page “https://www.essabank.com/index.cfm?” because the server where this page is located isn’t responding."
I never had this issue before.
I have Firefox and it does not work on that browser either.
I have also tried RockMelt and Opera, again without any luck.
I have searched on the web on several forums and the advice I saw there for similar issues did not work.
I called my bank and they were not having any problems and told me the problem was on my end.
I called Verizon and they tried to help, even took over the computer and they could not get the page to come up.
I can access the page if I use Kproxy, but, I cannot access the bill pay feature that has a totally different error message.
Does anybody know how I can fix this issue and gain access to my bank's page as I did before.
This is extremely important as I need to get to the page and to my bill pay feature without any issues.
As I said, this had been working fine up to about 2 or 3 days ago.
I am using Safari Version 5.0.5 (6533.21.1)
When I go to my bookmarks and previews, the preview for my bank is blank or black with the Safari logo and a lock on it, if this helps...
Any help is greatly appreciated as we really need access to our banks page and features that we use all the time....
Thank you in advance for any help with this problem.....

Greetings,
As you've tried multiple web browsers, try creating a new user account, log out of your current account, log in to the new account and try from the new user to see what happens: http://docs.info.apple.com/article.html?path=Mac/10.6/en/8235.html
Cheers.

Cannot access web console after install.

Hi all.
The last day has been my first encounter with Oracle VM and it seemed to go fine until I finished. I have installed the latest VM and management tools on a bare bones machine (spec below) but cannot access the console via http://machine:8888/OVA.
I have tried installing using https and without and can gain access to neither the https 4443 or the http 8888 yet I can ssh into it quite easily. The dmesg only really complains that there are no ipv6 routers (understandable) but the xend.log in /var/log/xen does show something strange at the bottom:
[2011-07-13 16:04:45 3011] DEBUG (XendDomain:452) Adding Domain: 0
[2011-07-13 16:04:45 3011] DEBUG (XendDomain:386) number of vcpus to use is 0
[2011-07-13 16:04:45 3011] INFO (SrvServer:177) unix path=/var/lib/xend/xend-socket
[2011-07-13 16:04:45 3011] DEBUG (XendDomainInfo:1727) XendDomainInfo.handleShutdownWatch
[2011-07-13 16:04:45 3011] WARNING (XendAPI:695) API call: VBD.set_device not found
[2011-07-13 16:04:45 3011] WARNING (XendAPI:695) API call: VBD.set_type not found
[2011-07-13 16:04:45 3011] WARNING (XendAPI:695) API call: session.get_all_records not found
[2011-07-13 16:04:45 3011] WARNING (XendAPI:695) API call: event.get_record not found
[2011-07-13 16:04:45 3011] WARNING (XendAPI:695) API call: event.get_all not found
[2011-07-13 16:04:45 3011] WARNING (XendAPI:695) API call: VIF.get_network not found <------ ?????
[2011-07-13 16:04:45 3011] WARNING (XendAPI:695) API call: VIF.set_device not found
[2011-07-13 16:04:45 3011] WARNING (XendAPI:695) API call: VIF.set_MAC not found
[2011-07-13 16:04:45 3011] WARNING (XendAPI:695) API call: VIF.set_MTU not found
[2011-07-13 16:04:45 3011] WARNING (XendAPI:695) API call: debug.get_all not found
The spec of the machine started out as:
Athlon 64 x2 3600+
4Gb Ram
2 Nics (1 built in Broadcom & 1 Intel MT)
1 NVidia super duper gt9500
3 Hard Disk, (1 IDE 150gb , 1 SATA 80 & 1 SATA 150 - the IDE is master boot with system on it)
After a few attempts, I removed Video and the Intel card.
The install was done via CD and never complained and in this last install, it only had 1 NIC to choose for the management console.
On this last install I also chose top use none https and therefore the system says I should gain access via http://machine:8888/OVA
I do notice though that in some tutorials, it states alternatives to OVA like OVS etc, all of which I have tried.
Oh and if I netstat -an, it shows it's listening on port 8888.
many thanks, I'm guessing it's some a bit silly that I've over looked but from the way I read the install instructions, you only need the VM and the management Disks to install and you should be able to access via web console?
BTW, systems I'm using as clients to access range from, opera, firefox (Soalris), ie 6,7,8 & 9 from Windows and Windows server. All I get is Internet Explorer Cannot Display This Page.
many Thanks, Mark

Did you install the VM Manager software as a VM hosted by OVS? Make sure the VM is running. It is probably named something like OVM_EL5U4_X86_OVM_MANAGER_PVM. Use "xm list" on the OVS server to see which VMs are running.
If it's not running, then run "xm create /path/to/vm.cfg" the path is probably something like /OVS/running_pool/OVM_EL5U4_X86_OVM_MANAGER_PVM/vm.cfg
Jim

Cannot access web server internally with ea6200

I have the same problem as found in these posts:
http://community.linksys.com/t5/Wireless-Routers/Cannot-access-server-internally/m-p/743969/highligh...
http://community.linksys.com/t5/Wired-Routers/Accessing-Internal-Web-Servers-External-OK-Internal-No...
http://community.linksys.com/t5/Wireless-Routers/EA6500-NAT-Redirection-Bug/td-p/583820/highlight/fa...
Basically, I can't access my local http http server. Like the other posters, this is a new router and I've never had this problem before. I know very little about networking, but I am a developer and need my server to be accessible on my LAN.
The only things I’ve done since setting up the router are:
Setup the wifi security
Enable the media prioritization as a user suggested in the last link I posted.
Forward ports 80 and 8080 – I did this knowing that it made no sense because I only care about local access, but since nothing else with this stupid router makes any sense, I figured, “what the hell!”
I really appreciate any help I can get. I’m thinking about just ordering a new router and sending this PoS back to newegg.

Hi jerred121, I've done a bit of a research about this feature. There is what we call DNS Rebinding Attacks, certain actions will not work from behind the router, this is for your own protection. I know it worked before with older routers.
If you need to access your server locally, you can use the private IP of that device rather than the public IP.

Cannot access web pages

I have perfectly good Internet but I cannot access any web page. On each page it says this for example on Facebook..."Safari cannot connect to the server. Safari can't open the page http://FB...because dafari can't Connect to the server www.FB..."

Is the Safari browser set to work Offline?
What are you using at the moment to visit the Apple Site?
Do you have any other web browser, such as FireFox, etc?
Have you checked any web-dependant applications or system time server
to see if these are accessing the internet and are getting data flow, live?
Could be the content of certain web sites may require a flash update or
some other thing, if only Safari is acting up. My Safari (in older OS X) is
older, it sees little use; my browsers are many & other newer ones work.
Good luck & happy computing!

Cannot access web site hosted on Azure VM

I have created Windows Server 2012R2 VM and after creating VM I have installed IIS and hosted my site and found it is working fine inside the VM.
Then I have added HTTP end point to my VM from azure portal. After creating http end point I cannot access my web site using MyHostName.cloudapp.net.
Can you help me why http end point is not working?
Then I have crated VM with template and there I have defined HTTP endpoint before creating VM.
Finally I found that if I create end point before creating VM then it works fine and if I create endpoint after creating VM then it doesn’t work.
Can you kindly help me to solve this issue (so that end point works properly after creating VM)?
Hasibul Haque,MCC2011,MCPD hasibulhaque.com

Hi,
You can check the port you bind for the website in IIS and make sure you have created endpoint with the correct port. You can also install Telnet client on your local computer and run "telnet xxx.cloudapp.net public_port_in_endpoint" at the command
prompt to see it works.
Have you enable SSL on the website hosted on Azure VM? If yes, please also create an endpoint with port 443 and open that port in Windows Firewall on the VM.
Best regards,
Susie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Cannot access web-streaming site

Windows 7 Home Premium 64-bit/SP1 OS...cannot access ANY cahnnels on "FreedoCast" web-streaming site (http://www.freedocast.com)...despite having latest Flash installed (version 11,6,602,180 installed). Probably not a browser issue as this occurs on IE9, Firefox 19 & Safari 5--of which is a screenshot attached--as you can see No Video--just a Black Screen & No Audio--Basically the same display on all 3 browsers---COULD this be a "Flash" issue or more likely the actual site (http://www.freedocast.com)--or perhaps something ELSE, I might not be familiar with??

Hi,
You can check the port you bind for the website in IIS and make sure you have created endpoint with the correct port. You can also install Telnet client on your local computer and run "telnet xxx.cloudapp.net public_port_in_endpoint" at the command
prompt to see it works.
Have you enable SSL on the website hosted on Azure VM? If yes, please also create an endpoint with port 443 and open that port in Windows Firewall on the VM.
Best regards,
Susie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Cannot access iCloud using my Apple ID password.

I cannot access my iCloud account. Yesterday I started getting a message that I need to review and accept the new iCloud user agreement. My password was rejected repeatedly, so this morning when I got that message, I followed the prompts and reset my password. The new password word works for the iTunes store and it got me logged in here, but it won't work with the iCloud.
*** am I supposed to do now?
Thanks for any help,
John

Solution: if you get the "Unsupported AppleID" dialogue following an OS update in OS X on a desktop / laptop.
     1) click "Cancel" button in the dialogue box,
then quickly
     2) switch to the main Preference window ( button in menu bar that looks like several rows of tiny icons)
     3) select the Security & Privacy Preference Pane, go to the Firewall tab and switch the firewall to OFF. (if necessary unlock padlock using your desktop keychain password)
     4) re-open the iCloud Preference Pane where everything should be normal again. Login to iCloud if required.
     5) switch back to Security & Privacy Preference Pane and switch Firewall back ON.
The above
Worked following "unsupported AppleID" dialogue blocked new agreement in the iCloud Preference Pane following upgrade to Yosemite 10.10.3. (March 2015)
I'm not sure which aspect of the Firewall triggered the AppleID issue, it may have been "Block all incoming", or "stealth mode", or…? It would seem that following significant changes or upgrades to the OS ones computer needs to re-establish an authenticated handshake with iCloud, by a different than everyday method is normally used to sync documents and data, and that a firewall blocks this initial handshake.
This may explain why some folks who have an effective router based firewall also have problems setting up iPads and iPhones.
Goodluck.
One could have reasonably have expected that Apple (the slackers) would have long since fixed this problem, or at least notified a workaround in the posted iCloud trouble shooting knowledgebase. This OS centred problem differs, from the earlier ICloud Authentication problem that was server based and affected users with very old AppleIDs that were flagged "Apple Retail Product Professional" which was caused by iCloud's database not recognising the Flag.

Cannot access web using hostname

Similar Messages

Maybe you are looking for