Cannot Access Wireless Network During Apple TV Set-up

I recently purchased Apple TV and was trying to set it up last night. I got as far as selecting the language. The ATV detects my home wireless network (as well as a couple of other nearby wireless networks), and allows me to select it, but I kept getting an error message stating that I could not connect and to try again later (then there was a (-6) at the end of the error message). It is not a password protected network.
I then unplugged ATV, my television, and my wireless router, waited a minute, plugged everything back in, and went through the drill again, with the same result.
I then re-started ATV using the remote and tried again. Same result.
I then ran diagnostics, which told me that ATV is running as it should be. Tried again with no luck.
I then tried the factory restore (even though I’ve yet to actually use the hardware), and got the same result.
I have a Dell Laptop, G4 iMac, and an iPod Touch that all connect to the network (from anywhere in my house) without issue.
I saw the following potential explanation/remedy, but I have no idea how to go about doing this:
Check the IP address Apple TV is using. If it starts with 169.x.x.x, then the router or base station may not be configured properly. Check to see if DHCP access is available or configure Apple TV with a manual IP address.
Any insights (please)?

Forgive me for the next question, which will probably reveal my ineptitude when it comes to doing anything other than following the directions of a setup wizard... but does my AppleTV even have an IP Address if it can't connect to my network in the first place?
I pinged "AppleTV.local" from another PC on my wireless network and it came back empty. I don't know how to otherwise go about getting the IP address.
Also - incidentally, I was able to connect ATV to a neighbor's open network, but obviously can't stream from my iTunes library. In hindsight, I wish I hadn't tried it, because I was able to watch a few movie trailers and now I have a better idea on what I am missing out on.

Similar Messages

Sometimes cannot find wireless networks??

i've looked around on a couple messege boards, but they didn't seem to be exactly the same problem i was having.
essentially, after waking up from sleep or hibernate, i sometimes cannot find wireless networks. the wireless switch will be on, Fn + F5 says my wireless is on, yet nothing can be found. strangely, when i try to turn off wireless, whether it's through Fn +F5, or the hardware switch, the light below the monitor remains ON. basically, i can't even turn it off. when i do click the button to try and turn off wireless, it gives me the busy cursor and eventually the whole menu disappears.
the way to fix this is by restarting.
just today, however, i suffered this same problem, even though i wasn't coming back from sleep or hibernate - it just lost connection randomly and then couldn't find any networks. attempts to turn off wireless failed.
is there a solution? is this actually the same problem that was remedied by changing a power setting?
thanks in advance.
Message Edited by supra97RX7 on 07-14-2008 11:47 PM

Yeah I'm having this problem too, with my antique T41 running XP. It used to be rock solid it seemed to change when I installed XP SP3.
I have tried reinstalling the Intel drivers but that hasn't helped. It seems when it restarts after hibernate (and occasionally at other times, as with the previous poster) it somehow doesn't lock on to the signal or it gets confused in the protocol or something. It doesn't always happen though - about one in three. Rebooting cures it...until the next time....
any assistance / ideas most welcome, thanks.
PS I'm using Windows Zero Configuration not Access Connections. That was a change some years ago that made it work better so I'm inclined to stick with that unless someone can tell me why not....

I have recently unlocked my iPhone 4. I got the comforation saying it was unlocked. For some reason I cannot access my network settings? Any suggestions. I am trying to use the phone on Net 10 network.

I recently unlocked my iphone 4. I am trying to use it on Net 10's network. However, i cannot access the network settings. I have the Net10 Sim already in it. A few notes listed below of what i have tried:
1.) I downloaded the iphone configuation utility. But cannot get the right settings to apply. (so if you have the correct ones i could use those)
2.) i have watched 1000 youtube videos and been on practically every page online and tried 1000 different versions of APN settings through the configuration
3.) I do not have another SIM card from another carrier to try.
Open to suggestions on how i can get the APN settings to change. Not worried about picture messaging or anything, but would like my internet to work. Calls and text work fine.

i have seen this option..problem being...i dont have access to WIFI i live in the middle of ten buck too! We cant even get internet out here i have to go a friend house to get internet. I was going to try that once i did get to town but was looking for other options here at home frist.

Cannot Access iTunes Store on Apple TV2 after purchase

Hello,
I cannot access iTunes Store on apple TV2. I purchased a movie, but when i got to watch it after it shows up as "Rented" it just sits at the screen "Accessing iTunes Store". Never times, out or produces error message. Internet is working fine, my account is fine.
If i launch an iTunes Store Trailer, it plays fine. Just my rented material does not play. Also, my Netflix account does the same thing from Apple TV2. While accessing Netflix on my laptop there is no problem. ***!

Having exactly the same problem. I have completed a reset, rebooted all my equipment and completed a software update, but after I have purchased 2 movies, and have them appear as "rented", I cannot get them to load without waiting a hour. Then, if I leave the movie, I have the same problem all over again. I also cannot access the iTunes store.

[network access] User cannot access through network

Hi!
I'm facing a strange problem now.
One of the users of my WD Personal Cloud cannot access through network share. When he tries to login the same fails and the login is prompted again. This happens in Windows but happens also in Linux.
When the same user tries to login in the mobile cloud app or in the browser (only in windows because after all this years the browser cloud funcionality still not works for Linux users, a shame...) it works as it should be.Also i tried to create a new users and happens the same, in the app or browser works great in network share simply refuse to login! I already rebooted, turn off, disconnected and did other things but nothing worked.
There are 9 users and 10 share in he cloud and the firmware version is v04.01.04-422. The diagnosis is OK!
Thanks for the help. Best Regards.

Hi again! There is no error. When i enter the share ask for the login credentials, i insert user and password and when i click ok simply ask the credentials again, and again, and again... It's the same compotment as if the credentials are wrong but they are not, i use them for online login in wd2go.com or mobile app and they work.And another thing is that if i create a new user happens the same, i can login in mobile app and wd2go.com but in the windows share (or samba share if in Linux) it fails without any error, simply ask for the credentials again and again and again... The old users works fine. The comportment is same with IP or name. Thanks for the help, Best Regards.

My Airport Extreme basestation used to work but upon returning from holdidays it no longer allows me to connect wirelessly through it to the internet on my iPhone, iPads, ipod touches and my apple tv2 cannot access the network either. Wired still works

When I returned from holidays I could not access the internet wirelessly through my Airport Extreme (5th gen) from my iPhone, iPod touches, ipads and my AppleTV 2 no longer can access the internet or the network either. I can get access to the internet on my iMac when wired directly into an ethernet port on the Airport Extreme. I have tried resetting my AirPort and created new networks but still doesn't want to co-operate. If I get wireless internet it is very, very slow and incosistent.
Any suggestions?
Rick

I see now that long questions are not going to be read and answered. Understandable. Since writing this I got help on one aspect of question and now have Airport Extreme visible through Airport Utility and it seems to work. However the wireless printer still does print. On the printer's screen, it recognizes my wireless network and connects. When I try to print from the MacBook, the usual printer icon comes up, but with Printer is Offline. Printer is Not Connected. So far, nothing in Apple or Brother help has given me answer to this problem. Any ideas would be appreciated.

Dumb question. Do I need to set up a wireless network for Apple TV?

Wireless newbie here. Recently purchased Apple TV... Trying to set it up and I don't see my wireless network available on the list... I have a built in Airport Extreme in my Mac Mini which I've never used before (or anything else wireless for that matter). I turned it on and I can see my MIni listed (and checked) under the computer to computer networks... Do I need to do something else? Thanks!

you have an airport extreme wireless card in your mac mini which lets you join a wireless network but you will need an airport express or airport extreme or other wireless router to actually create your wireless network... i.e. you don't go directly from mini to appleTV.. you need a wireless router between them.
Mac Mini <~~~~> Wireless router <~~~~> AppleTV
or you can also connect them with ethernet again through a router...

With Timed Access List on, Guest users cannot access Guest network.

I have a ABS with 7.5 version. In the Timed Access window i have default set to "no access". Then, all the computers that are allowed access to the main network are on the list. Then i have the main network hidden. My guest network is broadcasting but when a user tries to connect to it, they get a "Unable to connect". If I change the default access in Timed Access to "Everyday", users are then able to connect to the Guest network again.
Obviously, this is a bug. I don't want people accessing the main network that aren't on the timed access list. However, I still want guest users to access the Guest Network.
It looks to me that the Timed Access window is controlling the restriction of the Guest and Main network, when it should only be controlling the Main only.
Hopefully, apple has noted this issue and will be fixed on the new update. If other people are experiencing this problem, Please let me know.
-Ghost

Apple just updated the airport to 7.5.1. But there is still a problem with the the guest network not allowing access. If the "Unlimited" is set to "No Access" in the access list it prevents anybody from accessing the guest network. It should only deny your Main wireless Network.
In other words, the Access List is controlling the access for both wireless networks(Guest and Main network)
Either apple needs to create two Access Lists, One for Main network, and One for guest network. Or just have to option to choose which Network you want to restrict leaving the second one open for all.
-Ghost

Ipad cannot see wireless network

Hi, I have a wireless network using several Cisco 1131AG wireless access points. I have several Mac computers that see the wireless SSID and connect to the internet wirelessly. However, Ipads and Iphones don't see the wireless network. They cannot see the SSID at all. I have tried ipad 2, iphone 4 and 5. The network is not secured at this point. Any help with this would be appreciated.

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Cannot access internal network after Tiger upgrade

I've just upgraded an eMac (1.25GHz, 768MB) from 10.3.9 to 10.4.6. Although I can get online, access Mail and all applications, I cannot access the internal network at all.
I've updated to 10.4.9, but still no luck. I've restarted, logged in as a different user, logged out and in again, removed the 'com.apple.networkconfig.plist' file from the 'Library/Preferences' folder, but still doesn't work.
I can see all the aliases to the other machines on the network in the sidebar, but clicking on them brings up a message "The alias xxxx could not be opened, because the original alias could not be found.".
Other machines can see this on on the network. File Sharing is turned on.
Any thoughts, I'm tearing my hair out a bit!
Powerbook G4 Mac OS X (10.4.8)

no good, is an afpmounter error, i solved it with an
Archive and Install
http://docs.info.apple.com/article.html?artnum=107120-en
maybe someone have a solution..
i think is an error during the update (i had the same from panther to tiger)
with A&I and half-hour, your machine work perfectly.

Time Capsule Disconnects OTHER devices on wireless network during backup?

Hi everyone,
I need help here. I have a 500gb TC as my wireless base station as well as my backup for a new-ish 2.8 iMac. I have 2 laptops on the network as well as 2 airport express stations that just serve speakers. The house is a small 1-floor 3-bedroom.
Every time my iMac does a time machine backup (which is often), the airport express bricks lose their music streams, and the laptops (a original Macbook Pro and a previous gen. MacBook) lose their internet and network connection - BUT they still show full signal strength and show that they are connected to the network.
The only thing that seems to "solve" it is for me to turn my computer airport off then back on and wait for it to re-join the network.
I have tried resetting my Time capsule - which only resulted in a VERY slow initial backup which took over 2 days to back up 200gb worth of data and then back to the same problem.
I have the TC set up as a mixed n/b/g network, and I have one express brick extending the network ('cause I thought a weak signal might be the problem but it appears not), and the other brick joining the network. All firmware/ software is up to date. Any help is appreciated!
Many thanks,
jb

jwbeaton,
While it doesn't directly relate to your connectivity issue, might I suggest not storing other files on the TC. Use and external disk attached to the TC via USB.
*Using a Time Machine Hard Disk (or Time Capsule) for Other Files*
Here is Apples’ line on this: “Time Machine works best if you use your backup disk only for Time Machine backups. If you keep files on your backup disk, Time Machine won’t back up those files, and the space available for Time Machine backups will be reduced.” [http://docs.info.apple.com/article.html?path=Mac/10.5/en/11430.html]
This hasn't stopped some from successfully partitioning Time Machine hard disks and storing data on the other partition. As long as the Time Machine backup has its' own partition, you avoid any potential opportunities for conflict.
However, this is not an option for Time Capsule users as there is no easy way of partitioning the Time Capsules’ internal hard disk without elaborate effort. Granted, the Time Capsule is advertised as being able to perform both as a Time Machine backup destination and as a shared network drive [Apple Store (U.S.) - Time Capsule - 500 GB]
Nevertheless, some have experienced problems with maintaining files/folders occupying the same disk as Time Machine backups. In this case, they use the Time Capsule hard disk solely for Time Machine backups. Then attach an external hard disk to the Time Capsules USB port and store additional files there. This added disk will still be available to all Macs that can access the Time Capsule. (Note though, that any USB disks attached to the USB port of the Time Capsule can not then be backed up to the Time Capsule via Time Machine. Time Machine will only backup your Macs internal hard disk or any external hard disks physically attached to the Mac. Time Machine can not backup one remote device to another remote device.)
Hope this is helpful.
Cheers!

Vpn client can access internet but cannot access internal network

I am using PIX 501 to setup a VPN. At first the VPN client cannot access the internet once they logged in via the Cisco system vpn client, so i enable split tunneling. Now the VPN client can access the internet but they can't access the internal network.Due to the limited characters can be posted here, only necessary IOS coding is posted on the next message. Who knows how to solve this problem? Pls Help.....

enable password ********** encrypted
passwd ********** encrypted
hostname Firewall
domain-name aqswdefrgt.com.sg
access-list 100 permit ip 192.168.1.0 255.255.255.0 192.168.50.0 255.255.255.0
access-list nat permit tcp any host 65.165.123.142 eq smtp
access-list nat permit tcp any host 65.165.123.142 eq pop3
access-list nat permit tcp any host 65.165.123.143 eq smtp
access-list nat permit tcp any host 65.165.123.143 eq pop3
access-list nat permit tcp any host 65.165.123.143 eq www
access-list nat permit tcp any host 65.165.123.152 eq smtp
access-list nat permit tcp any host 65.165.123.152 eq pop3
access-list nat permit tcp any host 65.165.123.152 eq www
access-list nat permit tcp any host 65.165.123.143 eq https
access-list nat permit icmp any any
ip address outside 65.165.123.4 255.255.255.240
ip address inside 192.168.1.2 255.255.255.0
ip verify reverse-path interface outside
ip local pool clientpool 192.168.50.1-192.168.50.50
global (outside) 1 interface
nat (inside) 0 access-list 100
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) tcp 65.165.123.142 smtp 192.168.1.56 smtp netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.142 pop3 192.168.1.56 pop3 netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.143 smtp 192.168.1.55 smtp netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.143 pop3 192.168.1.55 pop3 netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.143 www 192.168.1.55 www netmask 255.255.255
.255 0 0
static (inside,outside) tcp 65.165.123.152 smtp 192.168.1.76 smtp netmask 255.255.
255.255 0 0
static (inside,outside) tcp 65.165.123.152 pop3 192.168.1.76 pop3 netmask 255.255.
255.255 0 0
static (inside,outside) tcp 65.165.123.152 www 192.168.1.76 www netmask 255.255.25
5.255 0 0
static (inside,outside) tcp 65.165.123.143 https 192.168.1.55 https netmask 255.255
.255.255 0 0
access-group nat in interface outside
route outside 0.0.0.0 0.0.0.0 65.165.123.1 1
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
aaa-server plexus protocol radius
aaa-server plexus (inside) host 192.168.1.55 ******** timeout 5
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set myset esp-des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map cisco 1 set transform-set myset
crypto map dyn-map 20 ipsec-isakmp dynamic cisco
crypto map dyn-map client authentication plexus
crypto map dyn-map interface outside
isakmp enable outside
isakmp key ******** address 0.0.0.0 netmask 0.0.0.0
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
isakmp policy 40 authentication pre-share
isakmp policy 40 encryption 3des
isakmp policy 40 hash md5
isakmp policy 40 group 2
isakmp policy 40 lifetime 86400
vpngroup vpn3000 address-pool clientpool
vpngroup vpn3000 dns-server 192.168.1.55
vpngroup vpn3000 wins-server 192.168.1.55
vpngroup vpn3000 default-domain aqswdefrgt.com.sg
vpngroup vpn3000 idle-time 1800
vpngroup vpn3000 password ********
telnet 192.168.1.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
terminal width 80

Cisco ASA 5505 L2TP VPN cannot access internal network

Hi,
I'm trying to configure Cisco L2TP VPN to my office. After successful connection I cannot access to internal network.
Can you jhelp me to find out the issue?
I have Cisco ASA:
inside network - 192.168.1.0
VPN network - 192.168.168.0
I have router 192.168.1.2 and I cannot ping or get access to this router.
Here is my config:
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 198.X.X.A 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network net-all
subnet 0.0.0.0 0.0.0.0
object network vpn_local
subnet 192.168.168.0 255.255.255.0
object network inside_nw
subnet 192.168.1.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool sales_addresses 192.168.168.1-192.168.168.254
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic net-all interface
nat (inside,outside) source static inside_nw inside_nw destination static vpn_local vpn_local
nat (outside,inside) source static vpn_local vpn_local destination static inside_nw inside_nw route-lookup
object network vpn_local
nat (outside,outside) dynamic interface
object network inside_nw
nat (inside,outside) dynamic interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 198.X.X.B 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication enable console LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set my-transform-set-ikev1 esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set my-transform-set-ikev1 mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set my-transform-set-ikev1
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh timeout 30
console timeout 0
management-access inside
dhcpd address 192.168.1.5-192.168.1.132 inside
dhcpd dns 75.75.75.75 76.76.76.76 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy sales_policy internal
group-policy sales_policy attributes
dns-server value 75.75.75.75 76.76.76.76
vpn-tunnel-protocol l2tp-ipsec
username ----------
username ----------
tunnel-group DefaultRAGroup general-attributes
address-pool sales_addresses
default-group-policy sales_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:5d1fc9409c87ecdc1e06f06980de6c13
: end
Thanks for your help.

You have to test it with "real" traffic to 192.168.1.2 and if you use ping, you have to add icmp-inspection:
policy-map global_policy
class inspection_default
inspect icmp
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

The process cannot access the file during Crystal Report export

We are exporting crystal reports into PDF using ExportToHttpResponse (code snippet below)
      // Getting the type of the report file which has been selected by the user. (which will be REPORT CLASS type)
Type objType = Type.GetType("WebApplication1.Reports." + ReportName);
ReportClass SEPREport = (ReportClass)Activator.CreateInstance(objType);
// GetTypedDataSet()returns an instance of typed data set.
SEPREport.SetDataSource(GetTypedDataSet());
SEPREport.ExportToHttpResponse(ExportFormatType.PortableDocFormat, Response, true, ReportName );
Now we have created these REPORTS using Basic Crystal Report 10.5, which comes bundled with Visual Studio 2008 and .Net Framework 3.0.
Now on our machines, we have never experienced any issues.
BUT on the DEV server (web server) which has .net Framework 3.0 and in its GAC its has CRYSTAL DLLs version 11.5 (required to create an Object of ReportClass and its related functions) ; sometimes we get the following error while exporting crystal report to pdf:
The process cannot access the file because it is being used by another process. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Runtime.InteropServices.COMException: The process cannot access the file because it is being used by another process.
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[COMException (0x80004005): The process cannot access the file because it is being used by another process.
   CrystalDecisions.ReportAppServer.Controllers.ReportSourceClass.Export(ExportOptions pExportOptions, RequestContext pRequestContext) +0
   CrystalDecisions.ReportSource.EromReportSourceBase.ExportToStream(ExportRequestContext reqContext) +525
   CrystalDecisions.CrystalReports.Engine.FormatEngine.ExportToStream(ExportRequestContext reqContext) +681
   CrystalDecisions.CrystalReports.Engine.ReportDocument.ExportToStream(ExportOptions options) +105
   CrystalDecisions.CrystalReports.Engine.ReportDocument.ExportToHttpResponse(ExportOptions options, HttpResponse response, Boolean asAttachment, String attachmentName) +163
   CrystalDecisions.CrystalReports.Engine.ReportDocument.ExportToHttpResponse(ExportFormatType formatType, HttpResponse response, Boolean asAttachment, String attachmentName) +132
   MSSB.FATools.UI.PlannerReport.CreatePDFDocument() +732
   MSSB.FATools.UI.PlannerReport.btnCreatePDF_Click(Object sender, EventArgs e) +45
   System.Web.UI.WebControls.Button.OnClick(EventArgs e) +104
   System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument) +107
   System.Web.UI.WebControls.Button.System.Web.UI.IPostBackEventHandler.RaisePostBackEvent(String eventArgument) +7
   System.Web.UI.Page.RaisePostBackEvent(IPostBackEventHandler sourceControl, String eventArgument) +11
   System.Web.UI.Page.RaisePostBackEvent(NameValueCollection postData) +33
   System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +5615

This is a cross post:
The process cannot access the file because it is being used by another proc
Do not cross post. See the [Rules of Engagement|https://www.sdn.sap.com/irj/sdn/wiki?path=/display/home/rulesofEngagement]
Setting this tread as answered and locking.
- Ludek

Macbookpro was stolen/recovered - how to track accessed wireless networks?

Hi All,
I have a MacBook Pro that was stolen and then recovered weeks later from someone who was not the original thief... Is there a way to find out the names of wireless networks accessed in hopes this would lead to the ID of the original thief? I've been looking at Console log under Diagnostic and Usage Messages, and here I can see exactly when the machine tries to autojoin wireless networks that have been remembered (and this is very useful), but wondering if I can find out the actual name of the network(s) joined in the hours after the laptop was stolen from me.
Thanks for any info you can provide!
For example - does this log below provide any revealing info?
6/25/10 12:36:21 PM airportd[4287] [most time: (2.753261) _association] trace: <CFArray 0x100500240 [0x7fff704dff20]>{type = mutable-small, count = 5, values = (
0 : <CFString 0x10003acb0 [0x7fff704dff20]>{contents = "prefnetwkAJ"}
1 : <CFString 0x10003ab70 [0x7fff704dff20]>{contents = "scan non-DFS channels"}
2 : <CFString 0x10051e210 [0x7fff704dff20]>{contents = "(1.637746) _scan"}
3 : <CFString 0x10051b260 [0x7fff704dff20]>{contents = "(0.000018) _lookup"}
4 : <CFString 0x100114380 [0x7fff704dff20]>{contents = "(2.753261) _association"}
com.apple.message.domain: com.apple.airport.autojoin.summary
com.apple.message.signature: AutoJoinSuccess
com.apple.message.result: success
com.apple.message.value: 4.446569
com.apple.message.value2: 29.000000
com.apple.message.value3: 1.000000
com.apple.message.uuid: B370AB1E-5CB6-4A23-AD69-EAAB22D9A879
Message was edited by: toastertu

Try the following to see if this will provide some information:
Open System Preferences (gear icon) on the dock
Open Network
Click on the AirPort connection on the left of the window
Click Advanced at the lower right
A list of previously joined networks will appear if the option to remember networks has been checked...unless this information has been deleted.

Cannot Access Wireless Network During Apple TV Set-up

Similar Messages

Maybe you are looking for