Cannot boot my MacBook Pro. Tryed CMD+R, reinstall OS, error message :damaged HD. When trying to repait it says it's OK. Yesterday HD wasn't even half full when I turned it off, now it says it's full.
Cannot boot my MacBook Pro. Tryed CMD+R, reinstall OS, error message :damaged HD. When trying to repait it says it's OK. Yesterday HD wasn't even half full when I turned it off, now it says it's full.
What may have happened is an error and a kernel panic, filling up the logfiles.
What I recommend is first to find a way to backup your data without booting the hard drive directly if it isn't already backed up, and then get Alsoft Disk Warrior to repair the hard drive. You'll probably want an external drive from http://www.macsales.com/
And you'll want to go into Hard drive -> Library -> Logs, System -> Library -> Logs, and Users -> yourname -> Library -> Logs to remove whatever you find there.
If after booting it fills up again, start by removing all startup items in your System Preferences for your user, and rebooting in safe mode with the shift key held down. If the hard drive is over 85% full after removing the logfiles, you may want to look at what were the last applications you installed.
Peer2peer software if installed can be as bad as a virus, because it enables others to access your computer. Insecure wireless networks are just as bad, if they are WEP or no encryption and someone is within 1500 feet of your computer.
If no such software is installed, your RAM probably has failed. Run the hardware test that came with your computer, by booting with the 'D' key.
If nothing shows up there, it can still be the RAM. Especially if you've seen any 4 language screens telling you to restart.
Here's more on kernel panics:
http://www.macmaps.com/kernelpanic.html*
Similar Messages
-
Trying to install adobe photoshop on macbook pro but at 50% it gives error message and kicks out dis
trying to install adobe photoshop on macbook pro but at 50% it gives error message and kicks out disc
copy the disc contents to a desktop folder and click setup in that desktop folder.
if that fails what ps version are you trying to install and what is your os version? -
Here's the ordeal. I'm running a 2007 MacBook Pro 17 inch with Lion OS. When I converted to Lion, I didn't have enough room on my harddrive to convert to the new FileVault, so I remained on the old system. Less than a week ago I reboot my computer because iPhoto seems to be stuck on "cataloging" my photos, though after days of letting it run, it doesn't do anything. After the reboot, my computer appears as if it had been reset to factory settings with all my programs gone, etc. I'm like, hey, I've got Time Machine, I'll restore it. After the restore is run, when I go to login, I get the dreadful error message, "You are unable to log into the FileVault user "John" at this time. Logging into the account failed because an error occurred". I searched the internet via my iPhone for suggestions and followed everyone of them, all the way down to erasing my harddrive and reinstalling Lion. So I get back into my computer and think I'm golden. I go to restore my computer via Time Machine and wham....I'm right back to that error message. I think, ok, I'll do it again. This time it messes us even more, giving me two login screens, one for the new Lion like before I restored the computer and then a second, as if it were restored, but unable to login. On top of that, I couldn't get back to the Command-R page! I thought I was really screwed! Well, I finally figured a way back, or maybe it was just that it finally decided to cooperate, I don't know, but I erased my harddrive again, and reinstalled again and thought, well, I'll rebuild manually by selecting what I want to restore from the Time Machine drive. I was able to get all my applications back and running, but to my dismay, I seemingly have lost all my iTunes music (except that which Apple has graciously setup to redownload now "thank you!) plus all my iPhoto's and even worse, all my DOCUMENTS!!!! Here I thought Time Machine from backing all this stuff up, but with over a years worth of back-ups I cannot locate any photos, music, or my documents on my drive to extract! Needless to say, I will never be using Time Machine again to back up my computer, I'll find another program or at least do it all manually. But my question is: am I looking in the wrong places for this files? Are they hidden under some unknowning folder that doesn't list it as music, photos or files? I can manage with the music, I can live with the photos because my wife has many of them on her computer and I have many uploaded to Facebook, but my files! My documents, thousands of them, many with information I won't be able to compile again, seemingly gone unless someone out there has any ideas?!!!
I even had iPhoto search the drive for photos and after hours of the barber shop pole spinning I cancelled the command for I figured it wasn't going to find anything.
If anyone has any suggestions, or if Apple, you are reading this and can provide some direction, I would greatly appreciate it.Also - my battery has been telling me "service battery" for a LONG time and then it switched to "replace soon" som time ago. Can't really see what this has to do with anything but whatever.
That could conceivably explain all the problems you're describing. Replacing a Mac's battery should not be postponed since a failed battery will cause other problems to occur. It is also possible that its hard disk has failed, which means the information on it may soon become unrecoverable.
... my latest TM back up was from April 2014, can I just run this when I have rescued everthing and then it might not be as slow?
If that Time Machine backup remains intact, it may be the only viable means of recovering that Mac's information. I suggest you do not attempt to restore its contents to your ailing Mac.
Given that you are having trouble creating a newer Time Machine backup you should stop using that Mac immediately and have it serviced as soon as you are able. Do not take it to anyone other than Apple or a service facility authorized by Apple, for the very reasons you explained. If there are no Apple Stores in your vicinity search for an Authorized Apple Service Provider using the Contact Us link below. Use one of the options that appear under Contact Apple Support. The language on that page will be different for your location. -
MacBook Pro plays start up tune, lights keyboard, but screen remains completely black. I don't use this computer often and wonder if lack of use contributed to the problem
I have a Macbook Pro 15'' Retina Display Mid 2012, and I'm having the same problem, but I use my computer very often. I use it to edit videos in Final Cut Pro X and sometimes when I'm editting videos my computer turn off unexpected.
When I turn On my computer again, Everithing seems to be working but the screen, just like yours. I had to turn Off and On a couple of time to make it work. =(
I don't know how to resolve this, I was looking for a similar article to debug it. -
when i try and upgrade the OS on my new macbook with retina i get an error message that it is not compatable
Hello, i have the same problem i have my brand new MacBook Pro retina display with mountain lion, but i can´t upgrade any app or installing from App Store, because all that app are compatible with 10.8.2 and not with 10.8.1 i ´ve been downloaded the upgrade from this link http://support.apple.com/kb/DL1581?viewlocale=es_ES, and i try to install it and they said that my Hard Disk is not compatible with this software. ***!!!! is the last new machine and i can´t upgrade!!!! please i need a solution, or a link whatever. i tried to re-install the mountain lion and is the same problem, today at the afternoon i will try with my time machine hard drive to see what happened beacuse in my ex macbook air 2012 i have the last O.S.
-
Mac Lion macbook pro, download pdf files fails, no error messages but work in Safari.
On requesting a download of a pdf file the source supplies this but nothing appears in the Firefox download window. Same pdf appears happily in Safari. My MAC pro with same Firefox progreamme works OK also.
Disabling a plugin worked for me
Go to Tools, Add-ons, Plugins tab
then disable the plugin: Adobe Acrobat NPAPI Plug-in Version 10.1.3 -
LR4 won't load on my Macbook Pro. I get an unknown error msg.
My copy of LR4 won't load on my MAcbook Pro. I get an unknown error message.
And that error message being exactly? Waht version of OSX? What MacBook exactly?
Mylenium -
My time capsule was working and then I added another Macbook pro. TC stopped appearing in Airport Utilities. I have tried resetting TC, I have turned if off and held reset button with pen for >10 secs. I just cannot work out what else to do? I have turned router off and on. Amber light is flashing.
The ethernet says self assigned IP 169.254.67.6
Then the ethernet is not getting an IP from the TC.. there is no connection.
I am not sure where you mean when you say the green LED should be on. Do you mean the TC?
Thanks
In order to help troubleshoot ethernet connections all routers use connectivity leds.. even APPLE.. it has one big LED on the front.. and 4 tiny leds beside each ethernet port. That light has to come on for ethernet to be active.. if you plug an ethernet cable into the port and the light doesn't come on.. then there is no connection.. either the other end isn't plugged in.. or the cable is bad.. or the ethernet port is bad.. something is wrong.
To get access to the TC you need this led to be green.. is it?
If it is green and the WAN is also green.. then I want you to unplug the WAN connection.. the blue wire in the picture.. the port slightly separated from the 3 LAN port.. computer plugged just into LAN port.. no airport turned on.. and press the reset again for 10sec until front led flashes rapidly.. then try and bring up the airport utility again.. assuming the ethernet led is green.
How old and what model is the TC?
The A number from the rubber mat will tell us the model. -
Dear all, I have a MacBook Pro bought in April 2011. Last April, it got stuck while the wheel was spinning and I had to force it shut. That cost me my hard drive. Now, it's stuck again. I tried esc, cmd+tab, moving the trackpad on the apple, but no. HELP!
Dear John,
thank you for your prompt reply. After I sent the email, I left the wheel spinning to see if it would eventually stop. It didn't, but after a while the screen turned blue, so I decided to switch everything off with a forced shut-down. I could not restart with the OS DVDs because I am currently away from home, but fortunately everything was more or less fine after restarting. It then got stuck again, I forced it shut again, restarted again, and now it seem to work but I won't overdo it and will switch off smoothly after writing this (unless it gets stuck again). Last April I have replaced the HD, so it's now just under 6 months old. And, of course, since the crash occurred when I was abroad and had backed up just before I left, I have lost only a few days' work. Still, and I know this will make me hugely unpopular here, with my 5 previous laptops running on MS Windows I never had a problem. Which does not mean I loved the OS, or I would not have switched to Mac.
Anyway, and this is the main reason for this message, thank you very much again for your speedy intervention.
Claudia -
Good Morning,
I have a MacBook Pro 15" and my warranty just ran out! I partitioned my harddrive into two partitions, one with Snow Leopard and the other with microsoft.This morning I turned on my Macbook Pro and it will not boot into Snow Leopard. I shut it off took out the battery, reinstalled the battery. Then I put in the Snow Leopard CD and booted up to disk utility and The Snow Leopard partion would not show up?? I do see the microsoft partion.
I also rebooted holding down the shift key and still no Snow Leopard
Could you please tell me what I can do, what keys do I press on restart any advice to get Snow leopard back.
thank you.Have you restarted holding down the Opt key? That procedure should give you a gray screen with all of the partitions that exist. Then select the SL partition for boot. Also go to System Preferences and Startup Disk, unlock the lock and select the SL partition as the default boot partition, then relock.
-
Can not start up on my Macbook pro. All I get is a grey spinning wheel. Tried all the Startup key combinations and nothing works. I reset the NVRAM and nothing. I booted with start up disk , ran disk repair and all is ok. Tried to re-install OS but when I get to designating drive its blank. When I go to startup disk there is a "?" mark. When I restart under startup disk search for a drive it still comes up with nothing. Before I got the grey spinning wheel I had a locked screen. Could not move curser or click on anything. Finally just shut down. Thank you in advance for any help!
Shouldn't still have a 'beachballing'... if the drive is being found and the system is trying to boot from it but is having problems, I would suggest looking over ds store's user tip - Step by step to fix your Mac.
It's likely either something corrupt in your system files or a failing hard drive. But follow ds's steps until you find the cause of the problem.
Good luck,
Clinton -
I have a macbook pro 15 retina - when ever I connect to bluetooth speaker, I get this loud noise coming from the speaker - if I turn bluetooth off, the noise is now coming from the macbook speakers & stays until i restart.
Hi John. Thanks for that input. At Step 6, after clicking "Next" I get a window telling me my OS version is unsupported and the installation may not complete. I am prompted to go to Canon's web site to "Check Latest Info".
I've had this window on previous attempts and from Canon's web site I downloaded two drivers as follows
- ICA Driver V4.0.0
- Canon IJ Network Tool V4.5.0
I'm not sure if these are the correct / complete drivers I need for this install or not.
I continue to follow all the steps. At step 9 I click "Wireless Set Up using USB" amd get a License Agreement (a little different than instructions)
I click "Agree" and it goes to a Setup window with two progress bars showing the installation. I've not been prompted to connect the USB?
After the Setup window is done, I am then prompted to connect the printer via USB. I connect the printer and click on "Redetect". It is not detected.
I then try following the Canon on screen instructions for connecting to the wireless LAN amd enter the password. It searches and indicates "Connecting" on the window, but it never connects and the blue light just blinks
So, at this point I am stuck??
Thanks
Stephen -
I accidentally forgot my passcode and tried 6 attempts but all failed.I don't have iTunes.I turned power off.Now it is not responding.Any suggestions?
Without iTunes on a computer there is nothing that you can do. If you are locked out because you forgot the passcode your only solution is to restore the iPad using iTunes on a computer.
I don't know exactly want you mean by it is not responding - does that mean that it will not power up again? -
Macbook pro stuck on grey apple logo screen - HELP! I've tried everything
I've looked through the forum for help and I think I've tried everything short of erasing and reinstalling mac os x -
- I've done an fsck (got "invalid volume count", "invalid node structure", "volume check failed" errors)
- booted from install disk and tried to verify disk (same errors as above)
- tried to "archive and install" mac os but got error saying "the destination disk must be erased for installation"
I tried T-starting my laptop connected to another mac (a powerbook g4) to try to backup my files before erasing and reinstalling mac os - but the mbp hard drive won't mount on the powerbook.
My latest idea is to try installing mac os x onto an external drive - and then booting my macbook pro from the external drive... and see if I get anywhere. my only concern is, I have to make SURE the option saying "Install Mac OS X - Installs Mac OS X for the first time" does NOT delete the contents of the external drive (it is a client's and cannot be erased!). I know there is also the option that says "Erase and Install" -- but I just want to make sure the first option will NOT delete the contents of an external drive.
Anyone know for sure? Or have any other suggestions? I have some work on my macbook pro that I cannot lose. Unfortunately I have not been backing things up... big mistake that I will not repeat.
Thanks in advance.DiskWarrior is the answer, as sig has suggested. It can sort out directory damage that is well beyond Disk Utility's repair capabilities. If you already had a bootable external hard drive of your own, I'd urge you to buy and download DiskWarrior and install it on the bootable external drive, then run it from there to rebuild the directory on your internal drive. I have to say that using a client's hard drive to solve your own problem would be appalling and unconscionable, and I hope you'll forget that idea.
If you can't see your way to buying an external hard drive along with DiskWarrior, you'll have to buy DW on a bootable disc, or order one online and wait for it to arrive.
If you can buy an external hard drive of your own in addition to DiskWarrior — and I can't think of any better use for a credit card, if cash is short — then you'll be able to boot your MBP to a Leopard installer disc, install Leopard on the new external drive, and then buy DiskWarrior as a download (rather than on a disc) and use it as I described above. After sorting out the internal drive with DW, clone the internal to the external drive with SuperDuper or Carbon Copy Cloner, and there's your backup from now on.
I should add that although Western Digital external hard drives seem to be available cheaply everywhere, I strongly recommend against buying one. Seagate drives are also widely available, and would be a better choice.
Message was edited by: eww -
i have a late 2011 macbook pro i want to reinstall os lion 10.7 so when i reboot hold down options key click on recovery hd then in the os x utilities screen it says reinstall mac os x is there any way i can save this download so i can burn to dvd
steve359 wrote:
Sorry ... I read but was unfortunately distracted from your original post. You have a system that came with Lion. The Lion that is on your system is only for your computer and cannot be downloaded from the app store again because you never purchased it officially through the App Store.
Try this for making an external USB/DVD copy of Recovery on an external disk. internet is still required for reinstall, though, I believe: http://support.apple.com/kb/HT4848. But at least you have a separate Recovery Partition if you ever need a fully new and empty internal disk.
Your assumption is incorrect. Although he may not be able to download it from the App store he can download it directly for the Apple servers using the recovery partition on his original drive.
All you have to do is start the install routine and then point the install to an external hard drive. Once the download is finished the computer will reboot to start the install. At that reboot disconnect the external drive so the install can not start. Boot the computer back into the OS on the internal hard drive, which is what will happen automatically once the external drive is disconnected. Then connect the external and copy the files from it that were downloaded. Right click on that downloaded package file and select Show contents. In the contents of that package is a file called InstallESD.DMG. Copy that file out of the package and burn it down to a DVD or USB thumb drive and you now have the Full Lion Installer. I have several of them laying around on different hard drives and 2 USB thumb drives which I have used to reinstall Lion on my 15" MBP.
Sorry OP I should of just typed this out in my first post.
Maybe you are looking for
-
Is there a button in Illustrator that disables colors from showing on the art board?
I have been trying to design a layout and when I go to apply colors to different parts, I can't. I am not able to see that color has been applied to the shapes. I have tried switching from RGB to CMYK and even Grayscale but it is to no avail. The sha
-
Hi, Previously I had lots of problems with showing a BLOB image from a table in a report using the apex_util.get_blob_file_src function. Varad put me right on several ocassions: see the thread at Confusion with get_blob_file_src Eventually everything
-
Using Single Datasource to Access Multiple Databases
Hi, We would like to know the pros and cons of accessing multiple databases through a single datasource, versus accessing each database through its own datasource. Our environment includes multiple web servers w/ the latest version of ColdFusion MX 7
-
Before I spend 10 bucks on the numbers app for iPad I have a few general questions. The main one being how compatible is excel and numbers. I want to know if I import a sheet I was working with in excel to numbers and that sheet has formulas, charts,
-
Explain HELMET or PEN in terms of OOP
Hi all, This is a question that was asked to me in an interview. How do u describe a PEN or a HELMET in terms of OOP concepts. The answer by me was PEN or HELMET can be considered as an obect with many characteristics like length, write, color and al