Cannot boot OS X 10.4 from External Drive

I have an external LaCie drive that has three partitions. I have 10.2.8 on one of the partitions, and I just installed 10.4 on another of the partitions. I am trying to boot from the partition with 10.4 on it, so I hold down "option" when the computer is starting up, and choose to boot from the 10.4 partition. However, whenever I try to start up from the 10.4 partition, the computer freezes up, and I get an error message. I took a picture of the error message, below is the link to the picture:
www.kesev.com/purposeposts
The computer boots up fine from the 10.2.8 installed on my internal HD and the 10.2.8 on the other partition of the external. The problem is simply with booting 10.4 from the external drive. Can anyone take a look at the error message which includes the message (Unable to find driver for this platform: "PowerBook3,5") and tell me what I can do to remedy this problem so I can boot from the OS X 10.4 partition?
Thanks a lot.
PowerBook G4 Mac OS X (10.2.x)

When you installed 10.4 on the other external partition did you use the PowerBook to do it or did you install it using another computer and then try to boot the PowerBook from it?

Similar Messages

Booting new (June 2010) Mini from external drives (USB2 vs 1394a)

I have a brand new mini and it doesn't seem to want to boot from the HDD I'm trying to migrate over from my old G4. The HDD is in a USB2 enclosure, and doesn't show as bootable in System Prefs->Startup disk. I'm considering getting a 1394a enclosure instead as I've read that is /definitely/ supported, but I've also read (on various forums, nothing official) that all Intel macs should be able to boot from USB2 external devices already.
The HDD has 10.4.x (I think .11) on it, and I really need to get that drive as the booted volume to recover some system preferences etc, rather than just have it mounted as a slave (it does mount fine).
So, before I go out and buy a 1394a enclosure, does anyone have any insight on this issue? Is the drive likely not booting the Mini because its in an USB2 enclosure, or is it because its an older OS, and wasn't formatted with GUID partition map?
I tried booting my wife's G4 laptop off the external USB2 enclosure and that didn't work either. I'm guessing the PPC needs 1394a to boot externally- I'm less stumped by that.
Any knowledgable comments/thoughts appreciated.

Any insight on the booting issue (irrespective of OS)? If this drive were upgraded to 10.6, could the Mini boot from it via USB2, or is 1394a required?
At least historically it has not been the case as a hard and fast rule- you have often been able to boot macs with older OS versions, to a point. Of course hardware eventually has a minimum OS needed to boot it, so it is often the case indeed. Do you know if there is a list of the minimum OS level needed by hardware revision? That'd certainly be a handy thing to have available.

External Drive with Time Machine, booting from external drive with utilitie

I'm using Time Machine now with
a LaCie 1TB external hard drive.
Everything works fine.
But, I've been wondering:
Can I place a program like TechTool
on the external drive (that Time Machine uses)
and boot from that external drive.
I would like to be able to do that,
because diagnostics and repair programs
only works properly and fully when they run from
external drives. Anything on the internal drive can be repaired
and examine. Impossible to do if Techtool is on the same
drive that's been examined.
Any thoughts as to what I should do?
Thanks
iMac, Leopard, Time Machine, Lacie Quadra 1TB drive.
P.S. Stupid question: If my computer crashes, and I reboot from Time Machine
(from the external drive) how does the computer know which backup to take ?!?
Isn't there many versions of the OS on the Time Machine backup taken at different times?

pitou wrote:
P.S. Stupid question: If my computer crashes, and I reboot from Time Machine
(from the external drive) how does the computer know which backup to take ?!?
Isn't there many versions of the OS on the Time Machine backup taken at different times?
As V.K. says, you can't boot from TM backups.
But you can restore your entire system from any one of them, per the procedure in #14 of the Frequently Asked Questions *User Tip,* also at the top of this forum.
You can also selectively restore from them, while running normally. See #15 in the FAQ Tip.
You might want to review these:
Time Machine Tutorial
Time Machine 101
How to back up and restore your files
Time Machine Features
Apple - Support - Mac OSX v10.5 Leopard Time Machine
and perhaps browse the rest of the FAQ Tip.

Problems booting from external drives

Ever since I got this 6-core 2013 MacPro (January 2015), I have had strange problems and glitches, but for this posting, I am talking about problems being able to boot up from external drives. I took the 4 external drives out of my old 2009 MacPro and put them into a 4-bay Thunderbolt enclosure. This enclosure can be configured as a RAID if all drives are the same (which they are not) or it can just be a place to be able to access all 4 drives. I used to be able to boot from each of those drives on the older MacPro but I am unable to do so now. They show up in the System Preferences/Startup Disk but if I choose one, it just reboots into the new MacPro drive. I even tried pulling out a couple of the drives and mounting each into a USB 3.0 (Sabrent) dock and still I could not boot from those drives which have the latest version of Yosemite. Yes, they are formatted correctly. I used to boot from them. I was able to clone one of the drives to a Seagate USB 3.0 hard drive and boot from that. Although, the clone was not perfect. It didn't transfer all my settings so I could recover some logins and serial numbers I wanted that I have never been able to retrieve since I got this new Mac.
Yesterday, I formatted a 32GB flash drive and tried to install Yosemite on it. I planned to put DiskWarrior on it. When I started to install Yosemite (from a saved download) it let me choose that drive, but when it restarted before installing, I was right back where I started on my MacPro's hard drive.
Is this normal behavior for the 2013 MacPro? Or is it just mine? I am beginning to think I may have a lemon since I have had other strange problems that don't go away.

Not all external devices are bootable. First stop would be involve whoever handles the 4-bay Thunderbolt. Seeing how it has a bridge most likely in order to support RAID mode that may not have the correct frmware or other reasons.
https://bombich.com/kb/ccc4
https://bombich.com/kb/ccc4/search/bootable%20volume
CCC is the only program I would be using.

When trying to transfer a folder from external drive to "users" folder, it says it cannot be modified because it is required by OS X. What does this mean?

When trying to transfer a folder from external drive to "users" folder, it says it cannot be modified because it is required by OS X. What does this mean? How can I transfer the folder?

It sounds like you're trying to replace a home folder. Replace the contents of the folder instead, or use Migration Assistant.
OS X: How to migrate data from another Mac using Mavericks

Trouble Booting from External Drives - MBA 2012

Hello,
I have a brand new 13" MBA which I'm working on building an image to use for deployment using Carbon Copy Cloner 3.4.5. For whatever reason, I can't boot the new 2012 MBA from an external LaCie FW800 or Thunderbolt 1TB Little Big Disk that is running either 10.7.2 or 10.7.4. As soon as I select the drive to boot from when holding the Options key or from selecting the partition from Startup Disk in System Preferences, I get the do not enter icon(circle with the diagonal slash). I tried both plugged in through a Cinema Display and plugging the Thunderbolt drive directly to the laptop. I confirmed both LaCie drives boot properly on an iMac and the last gen MBP/MBA.
Laptop Specs:
13"
1.8GHz Dual-core i5
8GB
128 SSD
10.7.4
Curious if anyone has run into any problems booting from external drives on the new 2012 MBA.
Thanks,
Paolo

Please be sure you have prepped these external drives correctly:
Drive Preparation
1. Open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
My suggestion for cloning is to use Disk Utility. This will also automatically clone the Recovery HD, as well:
Clone Lion using Restore Option of Disk Utility
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Select Disk Utility from the main menu then press the Continue button.
Select the destination volume from the left side list.
Click on the Restore tab in the DU main window.
Check the box labeled Erase destination.
Select the destination volume from the left side list and drag it to the Destination entry field.
Select the source volume from the left side list and drag it to the Source entry field.
Double-check you got it right, then click on the Restore button.
Destination means the external backup drive. Source means the internal startup drive.

Can Disk Utility get SMART status from external drives?

I recently updated my backup plan with a NewerTech quad-interface dock and a WD Caviar Green hd. I'm using the FW800 interface to connect to my iMac (10.6.7) Everything works perfectly, as expected. I noticed, though, that Disk Utility cannot report the SMART status on the new WD drive. DU simply says "Not Supported" under SMART Status.
Is Disk Utility telling me that it doesn't read SMART status from external drives? Or is it telling me that the new drive doesn't support SMART (which I would find highly unusual)? And, if it's Disk Utility that can't read the status, are there any third-party apps that can report the SMART status on an external drive?
Thanks,
JimC

Unfortunately I cannot speak to the NewerTech enclosure, but in principle it appears to be possible to have SMART information displayed even for external drives if the enclosure's bridge controller chip allows it.
My experience:
I've used two MacPower Pleiades FW800/400/USB/eSATA enclosures for several years and I've now supplemented them with two additional inXtron enclosures. They all work as expected daisy-chained to the iMac.
The interesting thing is that the inXtron enclosures came with a CD with some software on it ("Smart AP") which is not available for download, notably a Dashboard Widget for displaying actual and maximum temperatures, total hours of operation, start/stop cycles, drive model and serial number.
This widget is complete garbage, though – it is a nauseating nightmare of extreme over-design at the expense of even basic usability:
http://www.inxtron.com/information-center/smart-ap-for-external-hard-drives
To make matters even worse, it can only display the above information for the first external drive connected.
BUT: This Widget internally calls a command line utility which does the actual parameter retrieval, and that one can be called from the terminal as well.
So after installing the software from CD and effectively discarding the Widget, I checked out the command line utility in the Terminal and found that this utility actually reported data about ALL my enclosures, both the inXtron and the MacPower ones (there seems to be firmware compatibility across these):
(The '$' is supposed to be Terminal's bash prompt – type in only the rest of the respective line.)
$ /Applications/MacpowerAP/GetSMART 1
29 50 13 8
53 67 645 15829
52 53 90 7105
51 52 18 13
Each line reports the following for one connected enclosure:
[temp] [maxtemp] [cycles] [hours]
The drives are reported first USB, then FireWire drives, each in the order of first connection / mounting.
$ /Applications/MacpowerAP/GetSMART 2
WD-WCA**************
WDC WD30EZRX-00MMMB0
5TE09***************
ST31000333AS-00MMMB0
5TE09***************
ST31000333AS-00MMMB0
WD-WMA**************
WDC WD30EZRS-00J99B0
Each drive gets two lines reported, first the drive's serial number ("***" blocking out my exact ones), then the drive model.
$ /Applications/MacpowerAP/GetSMART 3
29 50 13 8
WD-WCA**************
WDC WD30EZRX-00MMMB0
53 67 645 15829
5TE09***************
ST31000333AS-00MMMB0
52 53 90 7105
5TE09***************
ST31000333AS-00MMMB0
51 52 18 13
WD-WMA**************
WDC WD30EZRS-00J99B0
This combines both of the above.
$ /Applications/MacpowerAP/GetSMART 5
disk4
disk1
disk2
disk3
This reports the mounted disk names (referring not to the volume names but to the internal Unix names as in /dev/[drive]); Numbering is in connection / mounting order, the actual sequence is as always USB drives, then FireWire drives.
$ /Applications/MacpowerAP/GetSMART 6
USB
1394
1394
1394
This reports the connection interface for each drive in the same sequence as all other commands.
$ /Applications/MacpowerAP/GetSMART 7
MPT934DS1.20.0104.00
MPT934DS1.20.0104.00
This might report the firmware revision or something like that.
These are the commands I know about, and they apply only to the "Smart AP" software supplied with current inXtron enclosures, but it may be possible that other brands use it as well.
I have not been able to identify information about the self-test (early(?) failure warning), but it might be contained as well in the data reported above.
As always, your mileage may vary and you should never do such experiments without FIRST making sure you've got backups of your data and that such backup is not connected during experimentation!
Maybe this can help some people getting the information they need; And maybe there are similar capabilities with other enclosures. At the very least it demonstrates that with the proper firmware in the enclosures themselves and some software on the Mac it IS possible to get at least some of the SMART information from the drive in an external FireWire- or USB-connected enclosure.
None of that is fed into the system's "official" SMART mechanism, though, so no luck using standard mechanisms or applications for it. It's strictly a command-line affair (deservedly disregarding the mishappen Widget).
Good luck!

Why won't photos from external drive stay on my computer (iPhoto) once I disconnect the external drive?

I'm trying to move photos from my external drive to my new computer. When I connect the external drive, I'm able to view all the photos in iPhoto, and I'm able to drag photos to a desktop folder and/or directly into iPhoto. But, when I disconnect the external drive, I no longer have access to the photos on my computer. I'm sure there's a step I may be overlooking but I'm using the same process I've used in the past and cannot determine next steps.

Thanks so far.
I'm currently working on a 2012 MacBook Air 13", running OSX 10.8.
Upon opening my external drive, I've dragged the iPhoto Library to my computer's desktop. When I've opened iPhoto and tried to import the library (from external drive and/or from the desktop), I'm unable to do so, i.e., the library is not highlighted (it won't allow me to click on it).
I can open and view the library from my external drive in iPhoto when the external drive is connected to the computer. But, once the external drive is disconnected from the computer, I'm unable to view the library
I've tried all of the aforementioned when the "Copy Imported Item(s) to the iPhoto Library" is checked.

Broken in Logic 9?: Reindex loops from external drive

Adding loops from an external drive in Logic 9 does not seem to work any longer. It used to work great in L8. Anyone have similar experiences? Know any work arounds? Is it a bug? If it's a bug I'll file it with Apple.
Previously in Logic 8 it was easy to reindex loops on an external drive:
(1) Delete the loop indexes from root/Library/Audio/Apple Loops Index
(2) Use Finder to locate the loops on the external
(3) Drag the loop folders into the L8 media browser.
(4) L8 asks if you want to copy the loops or use them from their present location. Select present location intsead of copy locally.
(5) L8 takes 5-20 minutes to build index of loops from external drive
I have tried this procedure several times in L9 without success. Instead I get the following:
(1) Delete the loop indexes from root/Library/Audio/Apple Loops
(2) Use Finder to locate the loops on the external
(3) Drag the loop folders into the L8 media browser.
(4) L9 ask for my admin password.
(5) Enter my password
(6) I'm NOT asked if I want to copy loops locally or use them in their present location. Instead a reindex progress dialog comes up for 2 seconds then goes away.
(7) In the end nothing happened. No loops copied, indexed, or anything
There is only one way I managed to get loops into L9 but it is exactly what I'm NOT looking for:
(1) In the folder with all my loops spotlight search ".CAF" (In this case want to reindex Apple content which is all CAF)
(2) Make sure to click "show more" at the bottom of the search results.
(3) Drag the search results to the loop browser.
(4) L9 indexes them all right, AND also copies them to my user library! All 30 GBs worth. Definitely not what I want.
In the end, I had to reinstall the Loops from the DVDs and specify an external location for them. (This whole mess got started when I tried to move the GarageBand and iLife loops to an external drive. The installer does not let you specify a location for them.)
Just so you know I've done some homework:
I've scoured other Logic forums and found these relevant threads that in the end did not solve the issue. They mostly seem to refer to Logic 8 which does not have this issue.
@ LUG
Thread 1
@ Logic Pro Help
Thread 1
Thread 2
Thread 3 this fellow seems to have a similar problem as I. He drags folders into the loop browser but nothing happens.
@ Apple Discussions
Thread 1
Thread 2

I just installed LP9 and all my loops and samples are on external drives. The drag and drop onto the browser method worked fine and I WAS given the option to move the files or not. The only exception to the above is Ultrabeat samples. They seem to want to be on the System drive.
RW

My Mac crashed. I got a new hard drive. I reinstalled Lightroom. Fortunately ircats are stored on an external drive. How do I import all of the old catalogues from external drive into a new LR catalogue. I have done it before. It has just been many years

My Mac crashed. I got a new hard drive. I reinstalled Lightroom. Fortunately ircats are stored on an external drive. How do I import all of the old catalogues from external drive into a new LR catalogue. I have done it before. It has just been many years and I can't recall how.

If you had stored your catalog files on an external drive, then all you have to do is double-click on them to open them and use them.
Or you could move them to the internal drive and double-click on them once the move is completed.
To create a single catalog file from multiple ones, you could use File->Import from Another Catalog

Since you can no longer backup to disk, how to restore from external drive without losing all ratings and playlists

since you can no longer backup to disk, how to restore from external drive without losing all ratings and playlists?

My own opinion is that you should install the later appropriate version of Silverkeeper. That said, I would in fact recommend if you can wait a few days for an answer, that you email the La Cie Silverkeeper backup team via the email link on the site at http://www.lacie.com/silverkeeper/
They are careful to say they are not officially providing a backup service, but when I emailed them with a query regarding usage about a year ago after downloading Silverkeeper for myself, I got a reply within a couple of days that cleared up my question.

Can't read iPhoto library from external drive

I suddenly can't can't read iPhoto library from external drive. I have talked to WD and nohing is wrong with the network drive. I can open images and files from it. But, I can't read in iPhoto Library.

Network Drive? a NAS?
iPhoto needs to have the Library sitting on disk formatted Mac OS Extended (Journaled). Users with the Library sitting on disks otherwise formatted regularly report issues including, but not limited to, importing, exporting, saving edits and sharing the photos.
Basically, you need to move the library to a correctly formatted disk.

I just had a new hard drive installed. After loading everything back on my computer from external drive, i came to the "select wireless network screen. I've misplaced the WEP password for my internet. Is there anyway to find it on another computer?

i just had a new hard drive installed. After loading everything back on my computer from external drive, i came to the "select wireless network screen. I've misplaced the WEP password for my internet. Is there anyway to find it on another computer?

Maybe. What kind of other computer are you talking about? What operating system is it running? What kind of wireless router are you using?
Your best bet may be to just reset the router and set it up again.
Just so you know, WEP is a very old security system for wireless and is considered insecure. If you have it available, use WPA2.

Best method of importing from external drive?

I have a 1T LaCie and want to know the best method to get those images into LR. The defaults are: "Add" and "NewPhotos" to "MyCatalog"
I think I may have more than one catalog and am not certain how to combine them. Is it best practice to have only one catalog?
Thanks in advance,
Mr Mayor

Duplicate thread, see Best method to import from external drive?

How do install program from external drive to mac book air

how do install program from external drive to mac book air

DVD or CD sharing: Using Remote Disc - Apple Support

Cannot boot OS X 10.4 from External Drive

Similar Messages

Maybe you are looking for