Cannot boot up Windows Disk

After putting my Vista disk in and clicking "Start Installation," the system restarts into part where it boots the disk, but it doesn't do that on mine. The disk is being read, but all I see is a flashing underscore at the corner of my iMac, and nothing else. I leave it on, for a while, and restarted a few times, but it's still like this. Any solution for this problem?

Yep, you are right!
It also worked for me to unplug the power for a few min.
Thanx M8

Similar Messages

Cannot boot to Windows disk to install XP (via Boot Camp)

I've got an issue w/ my late 2006 24" Imac that I have not been able to resolve.
Last week, I had the local Apple store replace the Video card in my Imac. The installed card was a nvidia 7300 GT. It was replaced w/ a 7600 GT (or at least that is what is reporting in System Profiler). My Imac had Tiger running w/ bootcamp beta 1.1.1 & a Windows XP partition.
After the card replacement, I was no longer able to boot to Windows. Selecting the Windows HD at boot-up resulted in just a grey screen. The tech at the Apple store said to try and do a Windows repair install, which seemed fine to me. Got the Imac home and found that I could not boot to the Windows install CD. Same result: a plain grey screen. You could hear the drive accessing the disk, but I saw nothing on the screen.
Went back to the Apple store, where the tech said all he could reccomend was a full wipe and re-install of the Mac OS & then new Windows install via boot camp. I was loath to do this for obvious reasons, but I went ahead and wiped the disk and installed Snow Leopard, with all updates.
So, of course, after creating the boot camp partition, I am STILL not able to boot to the Windows install disk. Everything else works fine, but when I try to boot to the Windows disk, I get just that same grey screen. I have tried re-burned copies of this disk, as well as two other Windows XP disks. I've also tried a Windows 7 disk; None of them worked.
So I ask here: Has anyone ever seen anything like this, and been able to get it resolved? What steps should I try next? Thanks for any help or insight you can provide.

WHY did you take it in?
And go back and have them provide (if they or AppleCare can) with a proper correct 7300GT. I don't see 7600GT as being used in iMac.
http://support.apple.com/kb/SP28
http://www.apple.com/support/imac/intel/
http://www.apple.com/support/bootcamp
Buy a copy of Snow Leopard for $29 to get Boot Camp 3.0. I assume you wanted Boot Camp 2.2 and that you need to upgrade to XP SP3 or later at this point.
As for burning Windows ISO - from where? and how? Disk Utility can, but not well, and to do so needs to be burned at REDUCED 2X if it is to work.
I'd say 75% of Store Geniuses are clueless when it comes to Windows on Mac, unless they've actually done it themselves and have hands on experience and "quote" gotten their hands dirty "end-quote."
That or build your own off the shelf Sandy Bridge based system.

Cannot boot into Windows XP, should I replace hard drive?

THE PROBLEM: I have not been able to boot into or use Windows XP (SP2) for almost 3 years. I have been using Linux instead for 3 years and am using it now. The Windows Recovery process only half works, it works up until you have to boot up the computer from the hard drive. Then it no longer works. The computer will load the files from the TOSHIBA Recovery and Applications/Drivers DVD that came new with the computer onto the hard drive. But when you get to the point of booting off the hard drive, with newly added Windows & Toshiba files, nothing happens. It does not boot up into Windows XP. In fact I can see the newly added Windows & Toshiba fileson the hard drive when I boot into Linux (Live) off the hard drive.
THE HARD DRIVE (Specs below): I ran a SMART Data check using a Linux (Ubuntu) Disk utility on the hard drive and it passed everything except for Reallocated Sector Count. There are 20 bad sectors. I called the Toshiba 800 # on the DVD and they told me that the problem may be the hard drive. A new TOSHIBA Recovery and Applications/Drivers DVD costs $40. Toshiba also said there is no Windows XP Recovery Console on the DVD.
CAUSE OF THE PROBLEM: I think, and TOSHIBA agreed it is either the hard drive or corrupteD files on the TOSHIBA Recovery and Applications/Drivers DVD
POSSIBLE SOLUTIONS: I have found a couple of sites that seem to have instructions for making a Windows XP Recovery Console CD. And I have thought I might try to run some Windows XP Recovery Console commands from such a CD, such as fixboot, fixmbr, etc. The try to see if I can boot into Windows XP from the hard drive. If I can, then that might suggest he problem is corrupted files on the TOSHIBA Recovery and Applications/Drivers DVD. If I still cannot boot into Windows, then maybe I should replace the hard drive. This should be very easy to do.
QUESTION(S): Does anybody have any comments or suggestions? Does my approach sound good? Do you have any other suggestions?
I have a TOSHIBA Satellite L25 S1216 that I bought new in early 2006. It has a 40 GB (5400 RPM) Enhanced IDE (ATA-6) 9.5 mm height hard disk drive in it. User removable, i.e., it is easy to replace.
Thank you,
Bob
Solved!
Go to Solution.

My plan is to try to use the TOSHIBA Recovery and Applications/Drivers DVD to load the WIndows XP files onto the hard drive, then use the Windows XP Recovery console CD I downloaded from here
http://www.proposedsolution.com/downloads/download-windows-recovery-console/
by using commmands such as fxmbr, fixboot, etc to see if I can get the computer to boot up into Windows XP.
Good plan, Bob!
Description of the Windows XP Recovery Console for advanced users
A backup plan would be to obtain a Windows XP installation CD from eBay or wherever. They are super cheap now. Then you could install Windows clean and add the drivers and utilities from the website here. Or you could use it to repair-install Windows.
How to Perform a Windows XP Repair Install
You are entitled to activate Home Edition for free. I understand that even after Microsoft no longer supports Windows XP (in April), they will honor activation attempts.
I wouldn't mess with SSDs. And stick with IDE PATA drives. You won't need to worry about advanced-format technology since that didn't come along until the very recent SATA drives. Your BIOS should support 120GB (KB303013). Some here.
-Jerry

I cannot boot my windows XP

I cannot boot my windows XP and it's driving me nuts.
I've tried booting it in safe mode but an error message: 'Sorry for the inconvenience...' appears with a list of boot modes; safe, safe with command prompt, safe with networking, last known...' which loads the windows splash page then the whole pathetic saga continues.
The last thing I did was to switch it off using the reset button,
I know it's daft but it was a rush of blood to the head.
My end and tether have joined up. Help!!!

at last empathy and humor!! you ray of sunshine!! the thing is I've tried several boot modes and guess wot they send me to the ms splash page then the same error message pops up. I'm like a dog chasing its tail.
however there is a blue dialog page that appears briefly with some guff on it but it never hangs around long enuff for me to read it. all I caught was was BIOS and then... nothing.
If my only solution is to erase the HDD so I will do it!

Cannot boot in Windows/Boot Camp anymore

Hello.
I'm Running OSX 10.10 Yosemite and Windows 7 x64 Ultimate.
I had Bootcamp working pretty well in my MacbookPro late 2013. But I needed a bit more space into the Win7/BootCamp partition. So I went to Disk Utility and reduced the "Macintosh HD" partition and applied the modifications. Until this, no problem.
I restarted my Mac with ALT key to boot into windows and assign the unallocated space to the Win7/Bootcamp partition. I used "MiniTool Partition Wizard Home Edition Free" in windows to allocate the space to the Win7/BootCamp partition. The program "said" it needed to reboot so that the changes could be applied because "Drive C is being used". And so I did.
When booting (in Win7/Bootcamp partition), Minitool partition wizard began making the changes, but right after they were done I got the message that "...changes were made to the partition..." and "...no bootable device...". So now, I cannot boot into Win7.
Also, if it helps, I followed this tutorial on youtube that seemed to work for the "youtuber" -- http://youtu.be/zhkdOLXT6Eg
So, anyone know how to proceed so that I can keep my partitions as is, whilst fully restoring normal BootCamp functionality ?
Thank you,
Ricardo Monteiro

The NTFS Header looks correct, which is surprising. It seems to be the old NTFS header.
From your current GPT output, you have
546998272 195733504      4
742731776 234373120      4 GPT part - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
From your Fdisk output you have
*4: 07 1023 254 63 - 1023 254 63 [ 546998272 - 430106624] HPFS/QNX/AUX
This is what recommend. Download GPT Fdisk from http://sourceforge.net/projects/gptfdisk/.
1. Delete the old entry and create a new entry at GPT#4.
sudo gdisk /dev/disk0
p
d
4
n
4
546998272
430106624
0700
p
w
y
Here is an example of the delete/new...
Command (? for help): d
Partition number (1-4): 4
Command (? for help): n
Partition number (4-128, default 4): 4
First sector (34-1954210086, default = 1454210080) or {+-}size{KMGTP}: 1454211072
Last sector (1454211072-1954210086, default = 1954210086) or {+-}size{KMGTP}: 1954209791
Current type is 'Apple HFS/HFS+'
Hex code or GUID (L to show codes, Enter = AF00): 0700
Changed type of partition to 'Microsoft basic data'
Command (? for help): p
Disk /dev/disk0: 1954210120 sectors, 931.8 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): 6ED0C429-00D1-4759-B50E-04B6FB80D0E3
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 1954210086
Partitions will be aligned on 8-sector boundaries
Total free space is 1293 sectors (646.5 KiB)
Number Start (sector)    End (sector) Size       Code Name
   1              40          409639   200.0 MiB   EF00 EFI System Partition
   2          409640      1452940543   692.6 GiB   AF00 Customer
   3      1452940544      1454210079   619.9 MiB   AB00 Recovery HD
   4      1454211072      1954209791   238.4 GiB   0700 Microsoft basic data
2. This is a tedious process and you want to check after the second 'p'rint command that it looks reasonable, before the 'w'rite and 'y'es to confirm.
3. You will need to reboot after the change, because the disk you are booted from is the one being modified. Reboot will rebuild disk0s4 using the start/end you entered.
4. Run the dd command - sudo dd if=/dev/rdisk0s4 count=1 2>/dev/null | hexdump -C and check that the first line contains "R.NTFS".
5. Once you have a working GPT#4, a new hybrid MBR needs to be created which will overwrite what you see in your Fdisk output. This is also done using GPT Fdisk (Gdisk). Your numbers will look different than what are in the following example. In most cases, you will use the default except entry 4, which should have a 'y' for bootable flag.
sudo gdisk /dev/disk0
GPT fdisk (gdisk) version 0.8.10
Warning: Devices opened with shared lock will not have their
partition table automatically reloaded!
Partition table scan:
MBR: hybrid
BSD: not present
APM: not present
GPT: present
Found valid GPT with hybrid MBR; using GPT.
Command (? for help): p
Disk /dev/disk0: 490234752 sectors, 233.8 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): 59BDFEEB-1EB4-4529-94FE-3CBC2C3CD513
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 490234718
Partitions will be aligned on 8-sector boundaries
Total free space is 2604 sectors (1.3 MiB)
Number Start (sector)    End (sector) Size       Code Name
   1              40          409639   200.0 MiB   EF00 EF
   2          409640       401060383   191.0 GiB   AF05 Macintosh HD
   3       401060384       402329919   619.9 MiB   AB00 Re
   4       402331648       490233848   41.9 GiB    0700 Microsoft basic data
Command (? for help): r
Recovery/transformation command (? for help): h
WARNING! Hybrid MBRs are flaky and dangerous! If you decide not to use one,
just hit the Enter key at the below prompt and your MBR partition table will
be untouched.
Type from one to three GPT partition numbers, separated by spaces, to be
added to the hybrid MBR, in sequence: 2 3 4
Place EFI GPT (0xEE) partition first in MBR (good for GRUB)? (Y/N): y
Creating entry for GPT partition #2 (MBR partition #2)
Enter an MBR hex code (default AF): AF
Set the bootable flag? (Y/N): n
Creating entry for GPT partition #3 (MBR partition #3)
Enter an MBR hex code (default AB): AB
Set the bootable flag? (Y/N): n
Creating entry for GPT partition #4 (MBR partition #4)
Enter an MBR hex code (default 07): 07
Set the bootable flag? (Y/N): y
Recovery/transformation command (? for help): w
Final checks complete. About to write GPT data. THIS WILL OVERWRITE EXISTING
PARTITIONS!!
Do you want to proceed? (Y/N): y
OK; writing new GUID partition table (GPT) to /dev/disk0.
Warning: Devices opened with shared lock will not have their
partition table automatically reloaded!
Warning: The kernel may continue to use old or deleted partitions.
You should reboot or remove the drive.
The operation has completed successfully.
6. a. Test 1 - Can you see your Bootcamp volume in Finder.
    b. Test 2 - Can you files in the Bootcamp volume?
    c. Test 3 - Can you see Bootcamp in your System Preferences -> Startup Disk.
    d. Test 4 - If Test 1-3 are successful, select Bootcamp and click on Restart. You may need Windows startup repair, if you see a hanging underline cursor at the top left corner of your screen. In most cases, it is not required.

Cannot boot in Windows 8.1 anymore (after making some changes in both systems)

Problem: I cannot boot in the Windows 8.1 partition created with Bootcamp anymore. When I try to do that, the system displays the grey screen then goes into a command line mode similar with MS-DOS and asks for inserting a disk (it reports no bootable drive).
Possible causes:
- I disabled the Bootcamp process in the Notification area in the Windows 8.1 systray
- I created a new partition in OS X on which I installed an older OS X version I still need to use (Mt Lion)

BroFlav wrote:
Can you tell me what exactly I should do in gdisk after merging the OS X partitions with their respective Recovery partitions?
Thanks, in advance.
Once you have EFI, Yosemite HD, Lion HD and Bootcamp, use the following steps. Your values will be different then this example. Use defaults except the boot ability flag for the last Bootcamp partitions to be 'y'.
sudo gdisk /dev/disk0
GPT fdisk (gdisk) version 0.8.10
Warning: Devices opened with shared lock will not have their
partition table automatically reloaded!
Partition table scan:
MBR: hybrid
BSD: not present
APM: not present
GPT: present
Found valid GPT with hybrid MBR; using GPT.
Command (? for help): p
Disk /dev/disk0: 490234752 sectors, 233.8 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): 59BDFEEB-1EB4-4529-94FE-3CBC2C3CD513
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 490234718
Partitions will be aligned on 8-sector boundaries
Total free space is 2604 sectors (1.3 MiB)
Number Start (sector)    End (sector) Size       Code Name
   1              40          409639   200.0 MiB   EF00 EF
   2          409640       401060383   191.0 GiB   AF05 Macintosh HD
   3       401060384       402329919   619.9 MiB   AB00 Re
   4       402331648       490233848   41.9 GiB    0700 Microsoft basic data
Command (? for help): r
Recovery/transformation command (? for help): h
WARNING! Hybrid MBRs are flaky and dangerous! If you decide not to use one,
just hit the Enter key at the below prompt and your MBR partition table will
be untouched.
Type from one to three GPT partition numbers, separated by spaces, to be
added to the hybrid MBR, in sequence: 2 3 4
Place EFI GPT (0xEE) partition first in MBR (good for GRUB)? (Y/N): y
Creating entry for GPT partition #2 (MBR partition #2)
Enter an MBR hex code (default AF): AF
Set the bootable flag? (Y/N): n
Creating entry for GPT partition #3 (MBR partition #3)
Enter an MBR hex code (default AB): AB
Set the bootable flag? (Y/N): n
Creating entry for GPT partition #4 (MBR partition #4)
Enter an MBR hex code (default 07): 07
Set the bootable flag? (Y/N): y
Recovery/transformation command (? for help): w
Final checks complete. About to write GPT data. THIS WILL OVERWRITE EXISTING
PARTITIONS!!
Do you want to proceed? (Y/N): y
OK; writing new GUID partition table (GPT) to /dev/disk0.
Warning: Devices opened with shared lock will not have their
partition table automatically reloaded!
Warning: The kernel may continue to use old or deleted partitions.
You should reboot or remove the drive.
The operation has completed successfully.
Now Reboot and verify the output of fdisk again.

Cannot Boot To Windows After Rescue And Recovery

I used the Rescue And Recovery disks (7 disks plus actually recovery cd) on my T42. I received the cd set direct from IBM. I've used the CDs in the past with no issues. This time after following the instructions and completing the restore, I cannot get the computer to boot to windows. It keeps going back to the Rescue And Recovery program. What can I do?

Refer to the following guide:
FAQ "How to use Recovery CD Disc Set".
"Also, if you get stuck after step 9 with Rescue and Recovery keeps on booting in a loop and not entering Windows then all you need to do is: GomJabbar wrote: While in Rescue and Recovery (with all CD's removed from your optical drive) you need to tell it to Restore Factory Contents. All the CD's really do is install Rescue and Recovery and the files needed to Restore Windows and the original Factory software."
I've come a long, long way," she said, "and I will go as far,
With the man who takes me from my horse, and leads me to a bar."
The man who took her off her steed, and stood her to a beer,
Were a bleary-eyed Surveyor and a DRUNKEN ENGINEER.
Present: T60 2007-55U, IBM 701c,
WorkStation: IBM IntelliStation A Pro.

Cannot boot into Windows

You have probably heardd this a thousand times, but...............
I have installed Solaris 10 on a hard drive with Windows XP Pro & Windows XP Pro 64 bit on other partitions.
Although the GRUB option to boot into Windows is there, chosing it results in the system hanging (ie black screen with just a flashing cursor).
Attempting a repair with XP 64 bit results in an error message to the effect that a "valid partition etc etc" does not exist.
Both the XP and XP 64bit paritions are still there and I can access everything on them from Windows on a second disk.
I therefore take it that the MBR has been changed.
So, you know the next silly question - how do I fix it so I can boot into my Windows XP Pro & Windows XP Pro 64 bit ?
Mike

It is advisable to be a bit more conservative and to perform backup of MBR before starting installation in quite complex environment. Appropriate command may have the form:
dd if=/dev/hda of=mbr.bin bs=512 count=1
Restoring:
dd if=mbr.bin of=/dev/hda bs=512 count=1
Here hda is a plug-in, sda may be necessary on other hardware platform.
But at present the milk has been spilled, so this tip is for future use. At first You should check the contents of grub.conf file in Your Solaris boot catalog. I assume that You can start Solaris. Are the partitions with Windows correctly enumerated? Remember that grub numbering starts with 0 (zero). If all is OK, You can try (without any warranty) following grub reinstallation procedure:
1) Boot from installation DVD and start single user shell.
2) Next issue a command:
/a/sbin/installgrub -m /a/boot/grub/stage1 /a/boot/grub/stage2 /dev/rdsk/c0d1s0
3) Check grub.conf contents - it should perform loading from the first disk. The value c0d1s0 depends on details of Your installation.
Additionaly I assume that You have installed Windows operating system on separate partition. All Windows data, i. e. Your user data are on another partition. In such a case You may try as a last resort reinstallation of Windows followed by new Solaris installation (+ previous MBR backup).
Good luck!
Mark

Cannot create bootcamp, cannot boot from Windows DVD or Bootcamp USB.

2011 Mac Mini, running 10.9 Attempting to create a bootcamp installation. Note that I have done this many times with other Macs, including similar Mac Minis.
I get through the Bootcamp assistant process of downloading windows support files and creating a USB drive for the install, I partition the internal 500gig hard drive in half. On reboot all I get is a black screen. Not a Black screen with flashing cursor, no error of any kind, just completely black, I have waited for over 45 minutes and it never changes. I have repeated this process several times, letting bootcamp assistant remove the partition in between, with several versions of the .iso file. I have recreated it from an original Windows 7 Pro 64bit. I have downloaded an iso of the same from Microsoft. None give any different results. I have reset the PRAM. I have a external Apple superdrive and have booted up to startup disk manager and can see that the USB is a valid boot, the Windows DVD is valid and there is an option for EFI Boot. None work, all give the exact same black screen with nothing. When booting from the Windows DVD, you can hear it spin up and read for a short while, then is stops. I have read and tried all the related posts here and on any web site I can find, although there are few and most just point back to the same articles here.
Help, tis is driving me crazy! I know it can be done, but there is something at work here I can't figure out.

You need to use a USB2 flash drive for BC Drivers/Windows ISO, not a USB3 stick. Windows installers do not support USB3 out-of-the-box. On Macs, BC drivers will later add support for USB3.

Satellite A200 - Cannot boot from Recovery disk - code 1

I have Vista business and my laptop is currently running slow and is full of rubbish.
I have in the past used my recovery disc to completely re-install vista and start from a fresh version.
However, i have tried this time and it says that it cannot boot from cd - code 1.
Can someone tell me what this is and how to re-install vista?

Hmm... so its definitely not a ODD issue but there is something wrong with the shipped CDs. From my knowledge this error would appear if the CD would NOT be bootable!
Its strange for me that this notebook has been preinstalled with the Vista business.
Usually the notebooks are preinstalled with Vista Home Premium and usually you have to create the own Recovery disk using the preinstalled tool called Toshiba recovery Disk Creator.
Anyway, if you are not able to boot from these disks then you would need other disks.
You could order it from the ASP in your country or from this page:
https://backupmedia.toshiba.eu/landing.aspx
Cheers

Equium L300 - Cannot boot from recovery disk or other CDs

Equium L300
bought new used 3 months the left for 9 months. Dead flat battery.
On restart
boot from hard -> disk Bootmgr is corrupt will not boot
boot from Recover disk cd -> The file is possibly corrupt. The file header checksum does not match computed checksum
boot from dvd windows install -> same as above
Tried numerours disks but will not boot.
No will it boot from USB stick. Pulled hard disk tried elsewhere seems ok.
Bios looks ok and sees hard disk and dvd etc
Any ideas otherwise a pretty dear machine for two monthe use.
Was just out of guarantee before fault appeared
Thanks chris

Hi buddy,
> But still think bios is corrupted
If you think so, then contact your authorized service provider. The technicians can check your notebook and try to reflash the BIOS. The technicians are really experts and so this shouldnt be a problem for them.
Here you can search for one:
http://eu.computers.toshiba-europe.com > Support & Downloads > Find an authorized service provider

[SOLVED] Grub error 18 - cannot boot to Windows

Earlier today I tried to install Arch 64bit (I had 32bit earlier) with kdemod to test new KDE4.2. However, after installation I could not boot neither Arch nor Windows. Grub appeared, but every single option gave me an error. I can't remember anymore which error it was, but It doesn't matter anymore. I thought I had made a really stupid and basic mistake while installing, I just didn't know what.
I wanted to test KDE4.2 so much so I installed Kubuntu (yeah, this topic is not related to Arch Linux, I hope that somebody can help me though, move this topic to somewhere else if it doesn't belong here ). Installation was fine, booting to Kubuntu was fine (and upgrading to KDE4.2 was fine), but booting to Windows was not. It gave me a following error:
Error 18: Selected cylinder exceeds maximum supported by BIOS
I googled a bit and found this: http://wiki.linuxquestions.org/wiki/GRUB#Error_18 I reinstalled Kubuntu using /dev/sdb1 as /boot and /dev/sdb2 as / (/dev/sdb3 is windows and /dev/sdb4 is my game partition, ntfs). Before this I had /dev/sdb1 as / and /dev/sdb2 as swap (now I have no swap at all, my 4GB RAM should be enough). The only difference was that at first grub gave me error 15 (I fixed it with Kubuntu LiveCD). After that - no difference.
I need Windows for playing. That's why it's very important that I can use it. [SOLVED] In addition, I should say that /dev/sda is a separated hard drive which is encrypted with Truecrypt. (I said this because I think that Kubuntu tried to install grub on (hd0)...) When I tried to mount this hard drive with Kubuntu, it couldn't do it. I wanted to test mounting on Windows to check if it is just Kubuntu's problem. If not, I'm fucked because this hard drive contains VERY VERY VERY IMPORTANT files. [/SOLVED]
I really need help, please. If somebody can help me, (s)he is my hero.
Last edited by Exitium (2009-01-29 14:42:32)

Oops, I forgot:
menu.lst:
(Yup, a lot of comments, Ubuntu style)
# menu.lst - See: grub(8), info grub, update-grub(8)
# grub-install(8), grub-floppy(8),
# grub-md5-crypt, /usr/share/doc/grub
# and /usr/share/doc/grub-doc/.
## default num
# Set the default entry to the entry number NUM. Numbering starts from 0, and
# the entry number 0 is the default if the command is not used.
# You can specify 'saved' instead of a number. In this case, the default entry
# is the entry saved with the command 'savedefault'.
# WARNING: If you are using dmraid do not use 'savedefault' or your
# array will desync and will not let you boot your system.
default 0
## timeout sec
# Set a timeout, in SEC seconds, before automatically booting the default entry
# (normally the first entry defined).
timeout 10
## hiddenmenu
# Hides the menu by default (press ESC to see the menu)
#hiddenmenu
# Pretty colours
#color cyan/blue white/blue
## password ['--md5'] passwd
# If used in the first section of a menu file, disable all interactive editing
# control (menu entry editor and command-line) and entries protected by the
# command 'lock'
# e.g. password topsecret
# password --md5 $1$gLhU0/$aW78kHK1QfV3P2b2znUoe/
# password topsecret
# examples
# title Windows 95/98/NT/2000
# root (hd0,0)
# makeactive
# chainloader +1
# title Linux
# root (hd0,1)
# kernel /vmlinuz root=/dev/hda2 ro
# Put static boot stanzas before and/or after AUTOMAGIC KERNEL LIST
### BEGIN AUTOMAGIC KERNELS LIST
## lines between the AUTOMAGIC KERNELS LIST markers will be modified
## by the debian update-grub script except for the default options below
## DO NOT UNCOMMENT THEM, Just edit them to your needs
## ## Start Default Options ##
## default kernel options
## default kernel options for automagic boot options
## If you want special options for specific kernels use kopt_x_y_z
## where x.y.z is kernel version. Minor versions can be omitted.
## e.g. kopt=root=/dev/hda1 ro
## kopt_2_6_8=root=/dev/hdc1 ro
## kopt_2_6_8_2_686=root=/dev/hdc2 ro
# kopt=root=UUID=e85e83e5-0f7c-419e-8cad-1fe5d9128e8f ro
## default grub root device
## e.g. groot=(hd0,0)
# groot=504fab5b-7bb6-4b20-af58-83677386de37
## should update-grub create alternative automagic boot options
## e.g. alternative=true
## alternative=false
# alternative=true
## should update-grub lock alternative automagic boot options
## e.g. lockalternative=true
## lockalternative=false
# lockalternative=false
## additional options to use with the default boot option, but not with the
## alternatives
## e.g. defoptions=vga=791 resume=/dev/hda5
# defoptions=quiet splash
## should update-grub lock old automagic boot options
## e.g. lockold=false
## lockold=true
# lockold=false
## Xen hypervisor options to use with the default Xen boot option
# xenhopt=
## Xen Linux kernel options to use with the default Xen boot option
# xenkopt=console=tty0
## altoption boot targets option
## multiple altoptions lines are allowed
## e.g. altoptions=(extra menu suffix) extra boot options
## altoptions=(recovery) single
# altoptions=(recovery mode) single
## controls how many kernels should be put into the menu.lst
## only counts the first occurence of a kernel, not the
## alternative kernel options
## e.g. howmany=all
## howmany=7
# howmany=all
## should update-grub create memtest86 boot option
## e.g. memtest86=true
## memtest86=false
# memtest86=true
## should update-grub adjust the value of the default booted system
## can be true or false
# updatedefaultentry=false
## should update-grub add savedefault to the default options
## can be true or false
# savedefault=false
## ## End Default Options ##
title Ubuntu 8.10, kernel 2.6.27-11-generic
uuid 504fab5b-7bb6-4b20-af58-83677386de37
kernel /vmlinuz-2.6.27-11-generic root=UUID=e85e83e5-0f7c-419e-8cad-1fe5d9128e8f ro quiet splash
initrd /initrd.img-2.6.27-11-generic
quiet
title Ubuntu 8.10, kernel 2.6.27-11-generic (recovery mode)
uuid 504fab5b-7bb6-4b20-af58-83677386de37
kernel /vmlinuz-2.6.27-11-generic root=UUID=e85e83e5-0f7c-419e-8cad-1fe5d9128e8f ro single
initrd /initrd.img-2.6.27-11-generic
title Ubuntu 8.10, memtest86+
uuid 504fab5b-7bb6-4b20-af58-83677386de37
kernel /memtest86+.bin
quiet
title Wintoosa
root (hd1,2)
savedefault
makeactive
map (hd0) (hd1)
map (hd1) (hd0)
chainloader +1
fdisk -l
(Note: These results are mainly in Finnish. It could be hard to you to read it... But whatever... I'll translate these only if necessary)
Levy /dev/sda: 640.1 Gt, 640135028736 tavua
255 päätä, 63 sektoria/ura, 77825 sylinteriä
Yksiköt = 16065 * 512 = 8225280 -tavuiset sylinterit
Levyn tunniste: 0xcc5d88e2
Laite Käynn Alku Loppu Lohkot Id Järjestelmä
/dev/sda1 * 244091 485122 1936074870+ b8 BSDI sivutus
Osion 1 loppu ei ole sylinterin rajalla.
/dev/sda2 176430 394864 1754572509+ 43 Tuntematon
Osion 2 loppu ei ole sylinterin rajalla.
/dev/sda3 177329 413105 1893868925 29 Tuntematon
Osion 3 loppu ei ole sylinterin rajalla.
/dev/sda4 57435 309703 2026342066 5c Priam Edisk
Osion 4 loppu ei ole sylinterin rajalla.
Osiotaulumerkinnät eivät ole levyjärjestyksessä
Levy /dev/sdb: 500.1 Gt, 500107862016 tavua
255 päätä, 63 sektoria/ura, 60801 sylinteriä
Yksiköt = 16065 * 512 = 8225280 -tavuiset sylinterit
Levyn tunniste: 0x0007a52a
Laite Käynn Alku Loppu Lohkot Id Järjestelmä
/dev/sdb1 1 128 1028128+ 83 Linux
/dev/sdb2 129 13185 104880352+ 83 Linux
/dev/sdb3 13186 26239 104856255 7 HPFS/NTFS
/dev/sdb4 26240 60801 277619265 7 HPFS/NTFS
Last edited by Exitium (2009-01-28 21:05:33)

MSI K9A2 Platinum + Phenom 9600 + 2GB Mushkin XP8500 cannot boot into windows

Hi!
I am building my computer using the Spider platform and I ran across problems during booting into windows.
I am using MSI K9A2 platinum with Phenom 9600 and Mushkin 2Gb kit XP8500 ddr2 1066. I have no problem installing windows xp.
The problem starts when I install the utility and drivers that come on a cd from MSI, my computer requests to re-boot after installation and after
that it will not boot into windows. I can get to the windows logo and then the system reboots right away.
I checked the bios and it shows that the ram is running at 800mhz and i have tried running with just 1 stick and im getting the same problem every time.
Anyone knows how to resolve this?
thanks!

Quote from: nirianto on 22-February-08, 01:32:52
Everything is stable now...I guess installing the driver from the MSI website is the best thing to do right now
I notice that my ram is underclocked to 800mhz instead of 1066mhz...I have update the motherboard BIOS to v1.2 and i checked that the ram is running on unganged mode...I tried adjusting the spd to 5-5-4-12 with voltage of 2.2v as suggested by the mushkin ram itself
Any idea?
"I have update the motherboard BIOS to v1.2 and i checked that the ram is running on unganged mode..."
That is the correct mode.
"I notice that my ram is underclocked to 800mhz instead of 1066mhz..."
1066 is not officially certified by JEDEC, also your memory probably don't have SPD configuration for that freq.
Contact to Mushkin for more details.
"I guess installing the driver from the MSI website is the best thing to do right now"
Yep
"Everything is stable now.."
nice :smiley:

Cannot boot from Windows 8 notebook - Error: Operating system version is incompatible with Startup Repair

Hi all,
I have searched through forums, but could not find the solution to my problem:
I have a notebook ASUS with Windows 8 preinstalled.
Yesterday I was doing some housecleaning jobs with some freeware tool (don't remember the name).
Afterwards I have not been able to boot into Windows.
CURRENT SITUATION: When I switch the PC on, after the welcome screen of ASUS and Windows 8 the system goes to a blank screen (no cursor, no mouse, CTRL+ALT+DEL not working).
On next reboot, it does not start automatically the Recovery/Repair procedure and goes through the same steps again. It's not a loop, it just hangs.
Looking into c:\windows\system32\LogFiles\Srt\srttrail.txt I see the following error message at the bottom of the file on the time of my last boot attempt: "Operating system version is incompatible with Startup Repair"
I tried several things without success, so now I want to solve the problems one by one and first thing is to understand what might be causing the "Operating system version is incompatible with Startup Repair" error and how it can be solved.
Thanks for reading

Hi,
Any update here?
I agreed with the others. First, if we have any backup available to restore Windows 8.1, we may take use of that.
If we don't have any backup available, we'd better contact the manufacturer side for a deeper help.
Or as Janek Fehn suggested, make a clean install of Windows 8, then update to Windows 8.1 again.
Best regards
Michael Shao
TechNet Community Support

E420 cannot boot into Windows 8.1

I am unable to boot into Windows 8.1 on my Lenovo ThinkPad Edge E420. The symptoms are as follows:
Normal boot (just press the power button): PC freezes on "Please Wait". There are no other buttons or menus available at this time. Assuming this "Please Wait" screen was for an update, I have waited over 8 hers to the point the PC just shuts down... rebooting results the same.
I entered a recovery mode via pressing "Enter" during the Lenovo splash screen and requested diagnostics. The diagnostic was unsuccessful.
I do not have a windows recovery CD/DVD.
Please assist with solution or recommendations.
David

I am unable to boot into Windows 8.1 on my Lenovo ThinkPad Edge E420. The symptoms are as follows:
Normal boot (just press the power button): PC freezes on "Please Wait". There are no other buttons or menus available at this time. Assuming this "Please Wait" screen was for an update, I have waited over 8 hers to the point the PC just shuts down... rebooting results the same.
I entered a recovery mode via pressing "Enter" during the Lenovo splash screen and requested diagnostics. The diagnostic was unsuccessful.
I do not have a windows recovery CD/DVD.
Please assist with solution or recommendations.
David

Cannot boot up Windows Disk

Similar Messages

Maybe you are looking for