Cannot browse phone or synchronise

Hi
I was wondering if somebody could help me. I have Nokia N70 and my set up is as follows:
- Windows XP SP2
- PC Suite 6.70.22
- Connected via USB cable connection
My phone used to connect to my PC and synchronise with PC Suite and Microsoft Outlook fine. However, recently it just stopped. I have looked all over the discussion forums and tried everything - uninstalling and reinstalling PC Suite, uninstalling and reinstalling the USB device drivers, deleting all calendar entries etc. The error message I get when I try to synchronise is "PC Sync has encountered a problem and has terminated the synchronisation." Also, I cannot browse the phone via Windows Explorer - when I click on Nokia Phone Browser\Nokia N70 an error dialog appears that just says "Operation could not be completed." The phone USB device drivers appear to have installed correctly in the Device Manager (on some installs they didn't but I ran the Nokia PC Suite Cleaner and afterwards they installed fine).
Any help would be appreciated. I'm beginning to think my PC is fine but my phone isn't.
Thanks
Mik

It helps if you can provide all relevant data, otherwise I will just end up suggesting nonsense.
It seems the new profile thing has something to do with this, but I cannot suggest anything.
About the browsing problem:
I am sure you have read the "32dll" - fix suggestion from this forum (I let you dig it up though :-) for the operation could not be completed. It is normally for XP SP´1, but if you do a lot of editing in your PC on your own, that might help.
If not, unistall again and run PC Suite Cleaner from www.nokia.com/pcsuite -> support and install PC Suite 6.70.22 again.
Good luck.

Similar Messages

  • Muse disables in browser editing of synchronised text

    I check the box in page preferences "Engable in Browser Editing"
    I also check the box "Enable for synchronised text
    Fasthosts, is running PHP 5.4 (and the documentation states 5.1 for in browser editing of synchronised text).
    And every time I upload the site, it tells me it's switched off the synchronised text editing.
    Why would this be?
    The site is this below. There's a phone and a desktop version with shared text.
    http://www.theretroagency.com
    HELP!

    This message will appear and InBrowser Editing of Synchronized Text will be turned off if/when Muse finds it cannot update the .htaccess file for your site during the upload process.
    Synchronized text relies on the use of .php for the pages of your site that include synchronized text. This means that one or more of your existing .html pages would change from being mypage.html to mypage.php. That change would break external links to the page and potentially impact SEO. Therefore Muse will put information into the .htaccess file so mypage.html works as the name for mypage.php and external links and SEO are preserved. If Muse finds it cannot write updates to the .htaccess file, then it doesn't use .php for any of the pages of your site and your page file names don't change. However, that means updating synchronized text via InBrowser Editing isn't available, since it requires .php pages.

  • The 3G symbol is not showing up on my home screen and I cannot browse the net, any suggestions?

    The 3G symbol does not show up on my home page and I cannot browse the Internet or receive mail. Any advice?

    reset the iphone
    1. press the wake/sleep button the top until you get the red slider
    2. Slide to power off
    3. Wait for phone to power off (you get a spinning gear icon for a while)
    4. press the wake/sleep button to turn in back on.
    if that doesn't work reset network settings
    1. Go to Settings->General->Reset->Reset Network Settings
    2. Confirm that you want to do this and the phone will restart itself
    if that doesn't work restore the phone in iTunes, but you will want to sync all of your data before you do that.

  • Cannot browse Netflix, only can see instant queue.

    When I open Netflix on Apple TV2 I no longer can see "Suggestions for You", "Browse", "Movies"...etc.  I can see instant queue, and logout.  I restarted and get same results.  Anyone else? 

    I've had similar issues with the Macs on my network (including the Mini on the TV); I generally cannot browse the streaming catalog with images and lose various levels of connects to Netflix CDNs (I usually lose all images of titles, in most cases cannot access the stream, in some cases can access the streams). This appears in my case to be a Mac specific issue (Windows machines, iPad, iPhone -- even Ubuntu, though it can't stream, can browse the library and get images from the Netflix CDN). Unitl today, a router reboot, clearing all caches and cookies, and some screaming would seem to get it working again ... Netflix (via phone) told me to contact Apple; their support script for Safari isn't even for 5.1 ... ugh ...

  • ITunes 7 cannot browse album covers on this computer error and crash

    Installed iTunes 7 yesterday, and now every time I try to go to certain pages in the iTunes store, such as movies or tv shows, I get an error saying "iTunes cannot browse album covers on this computer". Then iTunes immediately crashes. Has anyone else had this problem? Any fix??
    Compaq   Windows XP  

    I have the same issue. Not sure if this has anything to do with it, but I was on the Cover Flow View and it was working fine. I clicked on the full screen icon and the entire screen went random (meaning totally random pixels of color all over). I pressed the escape key and the normal screen returned, but it only showed a black section where the covers had previously been. I restarted iTunes and it started giving me the same message. I also can see them in the lower left and on the Album View. Just the Cover Flow view doesn't work. I downloaded the latest iTunes today and I keep all of the Windows updates on.

  • I have to open firefox twice otherwise it will freeze. I can see my home page but I cannot browse. If I close it and then reopen it works fine. I have just noticed this after installing the latest version

    Firefox freezes when I open it. I can see my homepage (incomplete) but I cannot browse. The cursor moves but cannot open anything. If I close and reopen firefox it works fine.
    == This happened ==
    Every time Firefox opened
    == I updated to the latest version of firefox

    These issues are usually caused by firewalls. See [[Cannot connect after upgrading Firefox]]

  • I have 2 computers (1 Pc and 1 MAC) and 1 Iphone.The I phone is synchronised with the PC. I want to synchronised it also with my MAC, without erasing all my music and files. Someone can help me to find the answer ?

    I have 2 computers (1 Pc and 1 MAC) and 1 Iphone.The I phone is synchronised with the PC. I want to synchronised it also with my MAC, without erasing all my music and files. Someone can help me to find the answer ?
    i have already try the copy/paste thing with the ID of the file "iTunes Music Library.xml" it didn't change a thing. each time I relaunched Itunes, the ID is the first I have in the MAC.
    I have more than 5 000 files of music. I don't want to recreate one by one all my playlits.
    Many thnaks for your answers.
    Constance

    You can sync iphone with one and only one computer at a time.  If you sync to another, it will erase the current content and replace with content form the new computer.  There is no way around this.
    Put everything on one computer and sync from there.
    BTW, you posted in the Home Share forum.  Your question seems to have nothing to do with home share.

  • How can I sync my photo contents in iPhoto on my iMac to my new iPAD's iPhoto?  I follwed all the instructions on manuals for both iPAD and iTunes re syncing, but I cannot find "phone button" under Device name on iTunes page. Please help!  Thanks!

    I follwed all the instructions on manuals for both iPAD and iTunes re syncing, but after physically connecting iPAD with iMac with USB or via WiFi I still cannot find "phone button" under Device name on iTunes page. Please help!  Thanks!
    I have been creating a photo book using a lots of photographs on iPhoto, and then I took another photos by using new iPAD which I want to integrate with the original album/book on iMac. I was able to import them from iPAD's iPhoto to iMac's iPhoto.  However I cannot import or transfer or sync anything from iMac's iPhoto to that of my iPAD. 
    So my iPhoto page on iPAD contains only 3 or 4 newly created albums, and no other info.  That means no syncing....
    I am supposed to be able to work on this project on either of these iPAD and iMac, correct?
    I am puzzled.  I appreciate for your advice and help.
    Thank you!

    It doesn't appear under the iPad device on the left-hand sidebar of iTunes, you need to select the iPad device on the sidebar and then select the Photos tab on the right-hand side of iTunes e.g.
    And then on the right-hand side :

  • WRT54G3G-ST - Connection is up but I cannot browse

    I have a WRT54G3G-ST with a PX-500 Sprint Aircard. If the connection is left idle for 6 - 10 hours it stays connected but I cannot browse or ping outside my local network, basically I cannot browse the Internet at all. The connection says it is connected. If I ping a valid Internet address from a command prompt or the router it fails. If I reboot or powercycle the router everything works fine. Anyone else seeing this?

    I believe this is happening to me.   Just started a few days ago.   If I rebooted and/or powered down the equipment, usually the signal would return.   I am a router newbie.   how do I reflashing the router's firmware?    What is so weird with this is that I can not surf the new with firefox or internet explorer, but I can send and receive emails though outlook on my personal PC.   On my work laptop, if I am not logged in through the VPN, I can not surf the net.   If I am logged in through my VPN for work, I can access the internet.    So instructions would be helpful or reference to a published doc.   
    Also, does anyone know how to change your email address on this board?  for the life of me, I can not find a place to do that.
    Thanks!
    junebuggnc

  • Extreme Problem - Cannot browse, or even connect.

    Setup: Airport Extreme connected to Unwired (ISP) ADSL modem by ethernet cable. Local ISP (Australia) ramps down the speed to dial-up speed if monthly download (1GB) limit is exceeded - that is the situation now.
    Problems: (1) I have an I-book that is "connected" to the airport, but the web browser (IE) cannot browse. I keep getting a "connection failure" message. Internet Connect shows a successful connection tot he wireless and to the internet.
    (2)I also have a PC connected to the Airport by the ethernet cable and can browse OK (but slow). However, if I try to connect the PC by the wireless to the airport I get the message that Windows cannot make the connection.
    The signal strength of the wirelss is very strong for both computers.
    I have called the ISP (Unwired) to see if there is some sort of hardware control info they need. No, they say to put everything in automatic.
    I have reset both the modem and the Airport's configuraqtion for maximum availability, and have left them off for a few minutes.
    Thewre is WEP encryption, but I have included the passwords when necesary.
    Any ideas?? Many thanks!

    gschelz, Welcome to the discussion area!
    Sounds like your iBook is experiencing a DNS problem. See KB 106798, Mac OS: Troubleshooting "A connection failure has occurred", "The specified server could not be found" or Similar Messages.

  • Cannot Browse Album Covers

    Hello All, first time posting here....hope someone can help! I have upgraded two versions of Itunes for my PC, the and I still cannot browse album artwork. I can see artwork for my playlists and main library, but when I click the far right button, I guess it would be called the Cover Flow button, I get a message saying "Itunes is unable to browse album covers on this computer."
    I installed Itunes for my gf last night on her pc, and that feature works great, but not on mine. Am I missing something?
    thanks,
    Kelly

    Thanks for the link, most helpful article! Looks like my video card is probably not updated, so looks like I'll have to update the drivers or may get a new video card, been wanting to get one anyways. I've downloaded a driver for my card from the SIS site, now it's in a zip file and I don't know how to open it! I'm running something called WinRar (i think)

  • Cannot browse the net

    i recently purchased  WRT54GS and since the day i bought it i am having this issue where i cannot browse eventhough i see the the wireless network connection icon strength showing either excellent or very good, several times i have taken online help on the linksys site but the problem remains, its just very frustrating, would some one please help??????

    You must setup a router first through a wired connection. If the computer works through a wired connection you can deal with the wireless side.
    Have you changed the router password from "admin" to something else?
    Have you change your SSID from "linksys" to something else on the router?
    Have you configure wireless security?

  • Cannot browse through bookstore by title

    I cannot browse through the bookstore by book title. I only see an author list, which is not really usefull. Untl now, I haven't found a function how to switch between author and title view.
    I own a iPhone 4S with the latest iOS version. On my iPad I can browse by title.
    kr
    Michael

    Just to update, don't know for what reason now I'm able to access the internet thru proxy after establish the VPN connection to my office.
    I did not change any setting at all and suddenly able to access thru proxy but I just can't ping the proxy server ip, the rest server ip I'm able to ping...strange...

  • Cannot browse to Outlook webmail - Firefox, Mac

    I have Firefox 35.0.1 and OS X Yosemite 10.10.1
    On Firefox, I cannot browse to webmail.oxfam.ca.  I can do so on Safari on the same computer but on Firefox, the wheel just spins, Connecting... and eventually it times out and I get a blank page with an error message.
    I've looked for solutions on line having to do with supported browsers, changing History and Security settings, and I can't find the solution. Cookies and cache have been cleared.
    I can get to OWA on my other Mac on Firefox.  It's running Mavericks instead of Yosemite and the add-ons/plug-ins are a bit different from between the 2 Firefoxes but don't know which ones - if any - to change.
    Any suggestions?

    Hi HewsieQ37,
    According to your description, I understand that you cannot use Firefox 35.0.1 logon OWA on Mac, however another Mac with same version works fine.
    If I misunderstand your concern, please do not hesitate to let me know.
    Firefox is supported for Outlook Web App when it runs on Exchange 2013, for your reference:
    https://support.office.microsoft.com/en-us/article/Outlook-Web-App-%E6%94%AF%E6%8C%81%E7%9A%84%E6%B5%8F%E8%A7%88%E5%99%A8-7bb72d5f-0b1d-47f6-bd6f-2623ab3aeed8?CorrelationId=9751a8d8-22ab-4e56-bf9a-422559b1419c&ui=zh-CN&rs=zh-CN&ad=CN
    Besides, since other Mac with same browser works well, it indicate that the issue may be related to client.
    During my research, I suspect the problem may be caused by Mavericks.
    Please try to update to latest version, meanwhile you can contact Mac support team so that you can get more professional suggestions.
    Best Regards,
    Allen Wang

  • Cannot browse other time machine backups

    I cannot browse other time machine backups on my time capsule. I hold down the option key and select "browse other time machine backups in the menu bar icon and I see no backups. Then I mount the time machine backup disk and I only see the the backup for the machine that I am using to do this. However, there are backups for two machines on that disk. One is called "outis" and the other "phaedrus". On the phaedrus machine, outis is not browseable and on the outis machine, phaedrus is not visible.
    I set up a test account and the test account could only browse the backup for that machine and not the other.
    How can I see all of the backups?

    kathigitis wrote:
    Am I mistaken or should all of this not happen and be available as soon as the TM disk is mounted?
    I just checked and it works the same way for me so I guess not. you need to mount the other sparse bundle first before you can browse it.
    That is to say, both backups are visible.
    Should I now revert to disk password in the AP utility?
    you can try and see what happens. the above method should work then too.
    Message was edited by: kathigitis

Maybe you are looking for

  • Vendor and Customer Clearing

    Dear Guru, I want to that why we want to clear the vendors and customers open items before making payment through F-13 or F-44 or F-32 I am quite confused. Kinldy clearify my doubts. Thanks in advance Moderator: Please, avoid asking basic questions

  • Organization Calendar for all applications

    Hi, it is possible to declare one time an Organization Calendar and refer it from each BPM process in the domain ? I ask this because it does not make sense to have a calendar for each process if all processes belongs to the same organization ...

  • Xslt extended method

    java code: import javax.xml.parsers.*; import javax.xml.transform.dom.DOMSource; import javax.xml.transform.sax.*; import javax.xml.transform.*; import javax.xml.transform.stream.*; import java.io.File; import java.util.Date; import org.w3c.dom.*; pu

  • Lens Correction Profile

    Hi I have CS6 on OSX Yosemite and have the latest camera RAW update. However, when I open a photo taken on a Fuji X10 in RAW, there is no Fuji option under lens correction. How do I get it to appear? Also, I have a Sony Alpha 6000 with 16mm-70mm lens

  • Manual Database creation in solaris -- checklist/steps required

    Hi, I am creating test databsae in my development solaris server. is there any checklist or process steps to guiding creation of oracle 10g database... the software is already installed... i can remember roughly..the steps are: 1. create pfile with a