Cannot connect 2nd Express as a Remote Base station

When I try to set up a 2nd express it doesn't connect.
I see in the Admin app that it has a "strange" IP address assigned. The Extreme Base station and the 1st Express have addresses like "192.168.9.x" and the new (2nd) Express has a 169.254.X.X and although you can see it in Admin you can't do anything to it.
I configured both the Express Remotes via Admin and use the "Auto config as Remote" feature in the WDS tab via the Extreme Base Station's configuration.
I also have an iMac with a hard-wired iMac connection to the Base Station.
Any ideas? Thanx.

I would do another reset and then configure the second Express manually. To configure the Express you have to be on the same network either with or without a wire.
Here are some steps to try and let us know the results:
- From your wireless laptop run Airport Admin Utility
- Select the Airport Extreme Bas Station (AEBS) and write down its "Airport ID"
- Open the configuration of the AEBS and note the channel number it is on. It should not be on "Automatic"
- Hard reset the 2nd Express
- Connect the Express to your laptop with an ethernet cable
- Both your laptop and the Express should be on the 169.254.x.x ethernet network since no DHCP server is available over their ethernet
- Open the configuration of the 2nd Express which has a name similar to "Airport Base xxxxxx" in Airport Admin Utility
- Change the Base Station name to something like "Express 2" and change the Base Station password so it's not the default "public"
- Leave the wireless mode as "Create a wireless network (Home Router)"
- Change the Network Name, wireless security and channel to match exactly what the other two Airports are set to
- Under the Internet tab change it to "Connect Using: Airport WDS"
- In the "MAC Address:" field enter the Airport ID of the AEBS
- Under the Network tab uncheck "Distribute IP Addresses"
- Under the WDS tab check "Enable this base station as a WDS Remote Base Station" and keep the check mark "Allow wireless clients on this base station"
- In the "Main Airport ID:" field enter the AEBS Airport ID again or click the Select button and pick it from the list (not the 1st Express)
- Under the Music tab set as desired
- Click the Update button finally and wait for it to update
- Disconnect the ethernet cable
- If necessary move the Express to it desired location
Did that help? If the "Auto configure as a WDS remote base station" from the Extreme doesn't work those are the manual steps to apply to an Express!

Similar Messages

  • Cannot Connect Airport Express to Airport Extreme Base Station

    I have just purchased a new Airport Extreme Base station and have it configured and running properly.
    I would like to use my Airport Express to play Air Tunes and have tried to join my Airport Express's network. I have not managed to get this to work.
    I have tried to configure the Airport Express manually and in Assist Me mode but every time it reboots to reconfigure the unit, it continues to flash amber. I have done numerous hard resets and followed the methods discussed in other posts but cannot get the unit to connect.
    I am running the latest firmware on both units.
    Has anyone solved this problem? If so, please help!

    Shallers...you are not alone.
    I spend several hours this past weekend trying to get a brand new Express to work with a brand new Extreme station using all Apple computers.
    Still no luck, after a gazillion permutations.
    I really like the Extreme, it works very well, even with non-Apple devices.
    The Express is going back....gawd awful thing from the Darkness.

  • Connecting Airport Express to Airport Extreme Base Station

    Hi Folks. I am at my wit's end.
    I have an Airport Extreme Base Station (main hub) purchased in 2003. Just bought a new Airport Express and it just won't connect to the AEBS. I think I've tried everything. From automatic WDS set up (described here http://docs.info.apple.com/article.html?artnum=107454) to using the Airport Utility and/or Airport Admin to set up. Nothing.
    I've looked through the discussions and found this http://discussions.apple.com/thread.jspa?messageID=7011490&#7011490 but the solution provided makes absolutely no sense to me.
    All I end up getting after numerous attempts at connecting to the AEBS is error messages and then a flashing yellow (amber I guess) light. When I do a "hard reset" it just goes back to flashing amber and it seems a factory reset doesn't work because according to this http://docs.info.apple.com/article.html?artnum=108044 I'm supposed to see the green light flash four times after I hold the reset button and plug in but that never happens.
    This is driving me crazy. Anyone have any ideas?
    Thanks.

    Hey John.
    I did finally solve the issue but I'm not quite sure how it happened but this is what I did:
    First, I did had hard reset on the AEBS and set it up all over again via AirPort Utility. I set it up to use a WPA/WPA2 personal password.
    Next I did a hard reset (not a factory reset) (hard reset: while plugged in, use a paper clip and hold the reset button for 15-20 seconds) on the AirPort Express and then restarted my computer.
    After restart, I opened AirPort Utility and set up the Express to join my AEBS network. When it got to the point where it asked me to choose the network to join, I chose my AEBS network and it magically knew the WPA password I had set earlier and then after that it was smooth sailing.
    I had tried a number of variations of that process many times before (and failed) and for some reason this time, it worked.
    Hope it works out for you.
    Best,
    Benjamin

  • Cannot connect to remote base station

    I have two airport express base stations.
    The one in my office is setup as a WDS main base main base station and is connected to the internet.
    The other one is installed in the kitchen as a WDS remote base station.
    Both base stations allow wireless clients.
    When I am in the reach of the main base station (in the office and in the kitchen), everything works fine.
    However, when I go to the living room (here i am out of reach of the office base station, but within reach of the kitchen base station), my laptop still "sees" the network, but is unable to connect. An error is given: "There was an error joining the airport network"
    I have re-configured the base stations several times; I also disabled the wireless security; I switched the base stations; .... no result
    Who can help ????

    I have the same problem at home. Somone else in this forum had a similar (though not absolutely identical) problem, for which another person suggested this:
    "It sounds like the issue may be the communication between the Cable modem & the AirPort Extreme Base Station (AEBS). Since you already have reset the AEBS, I suggest that you try a complete power recycle of your network components.
    "Modem/Router Power ReCycling
    - Power-off the DSL/Cable modem, Internet Router, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
    - Power-on the DSL/Cable modem; Wait at least 30 minutes.
    - Power-on the Internet Router; Wait at least 5 minutes.
    - Power-on the computer(s) "
    Since I am not home, I can't try the above right now, but will do so when I return home in a few days. In the meantime, if you are able to solve your problem, either by trying the above procedure, or by some other method, will you please let me know?
    Thanks a lot.
    MacBook Pro   Mac OS X (10.4.9)  

  • Cannot connect airport express to ipad I keep receiving the message: "an unexpected error occurred" when I try to connect my Ipad to my airport express.  Does anyone have a solution?

    cannot connect airport express to ipad
    I keep receiving the message: "an unexpected error occurred" when I try to connect my Ipad to my airport express.  Does anyone have a solution?

    I could not "see" my Express via my wireless router or via the Airport Utility until I reset it to Factory Settings by unplugging it then holding in the tiny reset button while plugging it back in, waiting for the flashing yellow LED signal before letting go.
    Then I set it up to DHCP - "connect to wireless network" and DOWNGRADED the firmware to 7.3.x
    I would tell you the exact Firmware but I can no longer "see" the Airport express............ AGAIN or still.....
    BUT at least I am listening to music streaming from my MacBook Pro... Hmmm.
    I log back into the router (Linksys WRT110) and it no longer shows the Airport Express as a DHCP client AND the Airport utility can no longer "find" any Airport Devices..
    So if I don't move, or there are no cosmic events, or maybe my KARMA is effecting the device or my "VIBES" are good, but I'm not sure if will continue to work.. Sure would like to use this little device from hel*.
    Since I have had this Airport Express I have spent many hours trying to get it to work.
    It works just long enough to fool me and then takes a dump...
    Maybe this time?
    5 Minute later...
    Music was playing. I went into iTunes and switched from Airtunes to Computer speakers. When I tried to switch it back GUESS WHAT?
    [An unknown error (-15006) occurred while trying to connect to remote speaker "Airtunes"]
    Wonderful Green LED though. Totally useless piece of equipment AFAIK.
    Message was edited by: Daniel Shattuck

  • Dedicating an Airport Express Remote Base Station to a BB Curve

    Hello all,
    Please forgive me if this has been answered in another thread. I have been searching for the last week or so and have found that many people are experiencing the same frustration with the BB Curve and H@H (UMA) service. Someone recently suggested that I dedicate the Remote Base Station to my BB Curve so as to grant the UMA a fighting chance (my network consists of one Main and one Remote base station). In other words, the problem, as I understand it, is that UMA/voice data gets kicked off the network in favor of true data. If I can dedicate my extra (remote base station) airport express to my Blackberry, then the UMA should work more reliably.
    Sooo...here is my question:
    How do I assign my remote base station (set-up through WDS) to serve only my Blackberry Curve? Should I not do this? How do I find my Curve's MAC and IP address? Which address do I need? So on and so forth...
    Thank you all who help.
    james

    No one seems to know what's going on! I'll retract it, then. Thank you for your consideration.

  • Cannot connect Airport express wireless

    Hello, cannot connect airport express wireless to linksys router.  Connected now with ethernet  cable but cannot figure wireless connection. My laptop cannot find the express while preforming setup scan, yet I'm connected to it.  I can connect with my iphone but not wirelessly. Any suggestions?

    ....I was then told over the phone that airport express will not connect to third party routers.
    This is NOT correct.
    The AirPort Express will connect to a wireless network if you know the following:
    1) The name of the wireless network
    2) The exact setting for wireless security that the network is using
    3) The wireless network password
    Most users know 1) and 3), but very few know the exact type of wireless security settings that their wireless router is using. The Express will not connect to the wireless network unless it receives all of the information listed above.
    So...we will assume that you know the name of the wireless network and the password for the network.
    Do you know the exact type of wireless security setting that your wireless router is using?  If not, the Express will not connect.
    You may need to check the setup of your wireless router....or if the router was supplied to you by an Internet Service Provider, they may be able to tell you what type of wireless security setting is being used.
    Post back when you have this info and we will proceed. There are still no guarantees that the Express will connect....but at least there may be a chance.

  • HT1178 Can I just use my airport express as the primary base station and the time capsule as the network client?

    I bought a new airport time capsule 3tb to be used to save to file all my pictures. Can I use it as network client and the airport express as the
    Primary base station?

    To my opinion this looks a bit like what I'm looking for.
    At the moment I have an Imac that is wireless connected to a 2TB time capsule (TC1).
    To this time capsule I have another 2TB time capsule (TC2) connected via a upt wire connection.
    At the moment there is a backup made via time machine from the Imac to the time capsule TC1 (the second TC is not used)
    I'm not so technical so I hope you understand the configuration.
    What do I want to achieve :
    copy all my data from the Imac to TC1 so that the information can be accessed by more users.
    create an automatic backup from TC1 to TC2 (mirror or raid system) for security.
    give access to some users on the network to access TC1 to read and write data.
    TC2 only serves as backup from TC1 and no direct access is needed to this disk.
    If there is a solution, thanks for explaining it in 'IT kindergarden style' so that I can understand and use the info.
    Many thanks in advance.

  • WPA2 - Webcam - Base Station - Remote Base Station ... How ?

    My Webcam is plugged into my Remote Base Station and uploads images over my WDS network to my Base Station perfectly ... and I can use my browser to access the Webcam's Control Panel - until I enable Wireless Security!
    Once Wireless Security is enabled on my Base Station and I have updated my WDS settings on the Remote Base Station, my browser can no longer access the Webcam and the camera's images are no longer transmitted to my Base Station.
    The type of Security makes no difference. I've had no luck with either WEP and WPA2.
    The only type of Security that allows the camera to use the WDS network is no Security!!
    Question:
    After I have enabled Wireless Security on the Base Station, does the Remote Base Station's Wireless Security also have to be enabled ?
    ---alan

    From the Camera Manufacturer:
    "Hi Alan,
    I'm not sure what is causing this. The camera doesn't know about the wireless. Any encryption is between the client and the base. Devices connected to the client should not be affected."
    Well - Thanks to that helpful tip, I have eventually determined that the correct procedure is:
    Step 1: Apply the encryption to the Remote Base Station that has the Netcam connected to it.
    Step 2. Apply the same encryption & password to the Main Base Station ... the one with Internet via Ethernet.
    Step 3. Rejoin my now 'closed' Network by selecting "Other" from the Airport menu in the Menu Bar.
    Step 4. Select the Network name from that popup menu
    Step 5. Enter my new WPA2 Personal Password.
    Success!!
    ---alan
    64 years old today!

  • Remote base station versus relay base station

    Okay, I give up. What is the difference between a remote and a relay? Can I daisy chain relay base stations? Will remote base stations act as "relays"? Are there any tricks to setting up the relay stations (remotes seem completely straightforward)? What are the positives and negatives of each?
    MacBook Pro   Mac OS X (10.4.7)  

    It seems like the distinction is more important if you want a wired connection to the station. If you're just tring to create a robust wireless network, can you do many remotes but just one relay? It seems like relay would be the way to go if there was no limitation on how many.

  • Relay vs Remote Base Station

    I have setup a WDS network with my airport express units.
    What is the difference between a relay station and a remote base station in a WDS network?
    Thanks
    Mike

    Yes, so lets say I have two aiport express. One of them is in my bedroom and it gets good reception from my router. And the second one is in lets say my den, and it doesn't get so good reception from my router, but it is close to my bedroom... Would I have both the bedroom and den airport express as REMOTE, or would i put the bedroom one as a RELAY and the den as a REMOTE, or the other way around. I have a WDS network setup.. or does it matter?
    Thanks

  • Old dome style Extremes used as a remote base station?

    Can the old dome style Extreme's be used as a remote base station using WDS?
    How would this be done?

    Yes - the "dome style" Airport Extreme Base Station can be configured as a remote base station, with your Airport Extreme N base station functioning as the main base station.
    The Airport Utility will guide you through the process.

  • Remote administration of Express in an Extreme Base Station network

    I am a newb administrator of a small network of an AEBS with 2 Expresses in "extend a network" mode. I can access the Base Station over the internet but I haven't figured out how I can do the same with the Expresses.
    Also, I understand that MAC filtering is unavailable for the Expresses in "ext a net" mode. Is this correct? It seems to be operational for the Base Station but even restricted MAC addys can access the network through the Expresses

    On this same topic;
    We have a new Extreme base station that connects 1 MBP, (wirelessly), 1 HP Laptop (wirelessly) and 2 PC (via ethernet) to the internet.
    All of the computers can see and use the Extreme base station and the printer connected to it via USB.
    We also have an Airport Express that the two laptops can see. This has a printer connected to it as well via USB. (both are new Canon printers and all of the software for each, and their drivers are loaded on all computers).
    Both the Extreme and Express have a steady green light, their own names and are set up on the same network.
    Though my MBP can see both the Extreme and Express, neither "see" each other as far as I can tell. And, the printer connected to the Express cannot be seen in either Bonjour Printers, or anywhere else.
    Also, in order to "attempt" to find the printer connected to the Express, I have to disconnect from the Extreme Base Station and connect to the Express.
    How can I get the printer (connected to the Express) to show up in my pick list of printers WITHOUT having to disconnect from the Extreme and connect to the Express. Also, how can we get the Express to be connected to the internet via the Extreme?
    All searches here and documents I have poured though do not address this issue and we'd really like to get this straightened out. I am willing to take a lot of time to do this, but do it right.
    Can someone please help me with this?
    Thank you in advance,
    ~ J

  • Using Airport Express as a remote WDS station to connect two wired LANs

    I have an Airport Extreme base station connected to a cable modem that gives internet access to both wired and wireless clients. I would like to wirelessly connect this base station to an airport express in a nearby building that also has a wired network so that both wired networks look like one big network. I figured that I would have to use WDS (using the Extreme as the main and the Express as the remote). I've followed all of the directions, but I'm not sure what the setting for Connection Sharing should be on the Express. Technically I am sharing the connection, but isn't the Extreme going to be doing all of the DHCP/NAT/etc.? So my question is, for this configuration what setting should I be using for Connection Sharing on the Extreme: Share a public IP address or Off (Bridge Mode)?

    So my question is, for this configuration what setting should I be using for Connection Sharing on the Extreme: Share a public IP address or Off (Bridge Mode)?
    "Off (Bridge Mode)" With this setting the AirPort Express Base Station (AX) will pass-thru the NAT & DHCP services of the AirPort Extreme Base Station (AEBS). That way all clients connected to either network will be on the same subnet.

  • Cannot connect airport express to existing Verizon DSL Network

    Hi all,
    I have just purchased a 802.11n Airport Express. The purpose was to extend my current wireless network and to rock tunes. I currently have a wireless DSL modem connected to Verizon via ethernet. The modem is a GT704WG verizon dsl wireless modem. When I try to use the airport utility and go through the set up I am told that the AE cannot connect to the network. During the setup it does see my current wireless network and asks for the password which I provided. But still it doesn't work. Is there a compatibility issue here? Will a 802.11n AE work with an existing modem?

    Hello ferrjerr. Welcome to the Apple Discussions!
    Which wireless encryption standard are you using on the Actiontec GT704-WG Gateway? WEP or WPA? If using WEP, I strongly suggest switching to WPA as WEP is no longer considered secure. If you are already using WPA, please try temporarily disabling it to see if the AirPort Express Base Station (AX) can now join the Actiontec's wireless network.

Maybe you are looking for