Cannot connect Airport Express to Time Capsule?

I had an existing wireless network with an Airport Extreme base that was extended with a first generation Airport Express. I replaced the Airport Extreme with Time Capsule because I needed the backup drive. Now I can't get the Express to integrate. When I try to bring it online, it brings everything down. I've reset it back to its defaults and am installing as if its new. The problem is that it brings everything else down. The two are connected via ethernet. For now I've had to take the Express offline until I can find a solution. Any advice?

Welcome to the discussions!
I don't have a solid answer yet to your issue, but would offer a few comments that might help sort things out.
I'm confused by your statement that you are able to extend the 2.4 GHz network, because the dual band TC does not allow the guest network to be extended. Check AirPort Utility - Manual Setup. Click the Wireless tab. I don't have a dual band TC, but I believe if you click the Options button, you will see more info about extending.
While there is a check box next to "Allow this network to be extended" for the main network, there is not a check box for the "Guest" network. It's not there, or least it's not there in the guide that I'm looking at.
I suspect that your computer was picking up the 2.4 GHz network from the TC, not from your Extreme. To verify this, open AirPort Utility again and click on Manual Setup for the TC. On the summary page, note the MAC address for wireless on the TC. Now, do the same thing for the Extreme.
Use your computer now to check things. Hold down the option key and click on the Airport icon at the top of the screen. The MAC address of the device that you are connected to will be displayed.
Have you tried to move the Extreme to a more remote location? You note that you have the two devices, TC and Extreme very close together. As a test, position the Extreme approximately half way between the TC and the area that you want to extend to and see if you can connect with your computer. Check to see if your computer is connecting to the Extreme or the TC by holding down the option key as above.
You have probably already done this, but check on the setup for the Extreme using AirPort Utility - Manual Setup - Wireless tab. There is a check box either on the Wireless page or the Options page to "Allow wireless clients". This must be checked for wireless clients to be able to connect to the the Extreme.
Post back with your findings and we'll try to figure this out.

Similar Messages

  • Best way to extend wireless via airport express and time capsule

    best way to extend wireless via airport express and time capsule
    i live in a two storey house where i use my airport express to create a wireless network in the main floor, and time capsule to extend it in the upper floor, where my room is. i have like 16 mbps in the main floor, and 2-3 mbps in the upper floor after having speediest.
    i used time capsule in the upper floor because i use wireless backup daily and don't want to put internet down while i im doin it and consequently my parent can have internet access in the main floor, am i right? or do i have make just the opposite in order to have a good internet speed?
    secondly, while checking airport express wireless mode on airport utility, there is like 4 different type of radio mode(802 11n bg comp, 802 11n 2.4, 802 11n a comp, 802 11n 5ghz) which i have no idea what they mean
    what do you recommend?
    we have like iphone4, iphone 3g, mbookpro, ipad, ipad 2, samsung tv and a sony vaio laptop in the wireless network
    thank you

    What you have would appear to be working but I can comment how I would redefine your setup.  Note that both Airport Express and Time Capsule can function as wireless base stations so you do have wireless everywhere and at all times — using the Time Capsules for backups doesn’t mean your parents won’t have internet access regardless of the where the base stations are located.
    You appear to have devices to connect to your network that use the 2.4 GHz band with 802.11g such as the iPhone 3G and perhaps the 5 GHz band with 802.11n such as likely the Macbook Pro if it’s a recent model.  The iPhone 4 can use 5 GHz and 802.11n.  Can’t comment on the Sony and Samsung but you can check their specs.
    Now the Time Capsule (if it’s a recent version), can simultaneously supply 2.4 GHz and 5 GHz band signals, but the Airport Express (if it’s recent) can only use one of those bands at one time.  Likely the lowest common denominator for your devices is going to be the 2.4 GHz band since the devices that are capable of using 5 GHZ also support 2.4 GHz.  If you don’t use 5 GHz, you won’t lose much in a two-storey home because likely it’s the 2.4 GHz band is better signal anyway because 5 GHz signals drop off quickly with several walls/floors to penetrate.
    You also didn’t mention if the Airport Express is used to support a printer and/or AirPlay (using iTunes to play on remote speakers via the Airport Express connection) but that might also be a factor in the best location to place the Airport Express.  Although the printer could be switched between the Time Capsule and the Airport Express if needed, only the Airport Express will support your remote speakers.
    Recommend you use the Time Capsule as the Base station.  When using Airport Utility to define the network, after you name your network, etc., select the Wireless tab, check the box “Allow this network to be extended” and set the Radio Mode to "802.11n (802.11b/g compatible)”.
    Using the Airport Utility, click on the Airport Express; after you define the device and network name, select the Wireless tab, define the Wireless Mode as “Extend a Wireless Network” and check the box “Allow wireless clients”. 
    Hope that helps.

  • Cannot connect airport express to ipad I keep receiving the message: "an unexpected error occurred" when I try to connect my Ipad to my airport express.  Does anyone have a solution?

    cannot connect airport express to ipad
    I keep receiving the message: "an unexpected error occurred" when I try to connect my Ipad to my airport express.  Does anyone have a solution?

    I could not "see" my Express via my wireless router or via the Airport Utility until I reset it to Factory Settings by unplugging it then holding in the tiny reset button while plugging it back in, waiting for the flashing yellow LED signal before letting go.
    Then I set it up to DHCP - "connect to wireless network" and DOWNGRADED the firmware to 7.3.x
    I would tell you the exact Firmware but I can no longer "see" the Airport express............ AGAIN or still.....
    BUT at least I am listening to music streaming from my MacBook Pro... Hmmm.
    I log back into the router (Linksys WRT110) and it no longer shows the Airport Express as a DHCP client AND the Airport utility can no longer "find" any Airport Devices..
    So if I don't move, or there are no cosmic events, or maybe my KARMA is effecting the device or my "VIBES" are good, but I'm not sure if will continue to work.. Sure would like to use this little device from hel*.
    Since I have had this Airport Express I have spent many hours trying to get it to work.
    It works just long enough to fool me and then takes a dump...
    Maybe this time?
    5 Minute later...
    Music was playing. I went into iTunes and switched from Airtunes to Computer speakers. When I tried to switch it back GUESS WHAT?
    [An unknown error (-15006) occurred while trying to connect to remote speaker "Airtunes"]
    Wonderful Green LED though. Totally useless piece of equipment AFAIK.
    Message was edited by: Daniel Shattuck

  • Conflicts with Airport Express and Time Capsule

    I am using Airport Express and Time Capsule at the same time. Connection to the web is via a router. Very often I do have conflicts. How shall I connect the gadgets? At the moment I connect the router to Airport Express (network cable).
    Time machine back up doesn't work properly.
    Is there anybody able to help me?
    Regards

    What broadband type do you have?
    It can be impossible to plug a TC into the existing connection because the virgin media router has special setup or logins which are not revealed to end users.
    If it is a fibre connection for instance the TC may simply not work. They have issues with many fibre ISP putting the gateway address outside the subnet of the main public IP.. (don't worry if it is too technical .. it amounts to .. it don't work! )
    You may need to wait until Sat.
    Get in a big supply of home videos or something and try and starve off your addiction.

  • Airport express and time capsule config?

    I have an airport express for Wi-Fi internet and printing. I have purchased a time capsule as a back -up drive to work with time machine. Should I
    set it up seperately from the airport express or
    replace airport express with time capsule ?
    What's the best config and can I retqin existing netwrok ID and password?
    Thanks for pointing me in right direction.

    Hi Yoreilly:
    i'm not sure just what setup is right for you.  and i'm sure the newer Airport Express is way improved over mine (got mine few yrs ago).  but my Airport express works as extension from your Time Cap Wi-Fi.  Airport does not put out wireless Wi-Fi signal on it's own. 
    1>  if yours can take your phone line & send out Wi-fi signal on it's own, then more power to you/ & you could sell back your Time Cap & just have a WD backup drive, or seagate external drive for less. 
    2>  otherwise, your airport express needs to connect to your Time Cap, to answer you #2. 
    3>  usually the application helps where you have dead spots in your house, or your location of Time Cap can't reach places in your house where U need Wi-Fi signal, or where you can't thread an ethernet cable out to your printer or device.
    not sure how you are setup with your wireless printer now.  but if your setup allows you to print by only using the Airport Exp, sure you can use the TimeCap separately as it's own Back-up drive.  the thing is it has Wi-fi capability that you wouldn't be using with that setup.
    hope this helps, & didn't confuse,
    m

  • Printing completely broken on both airport express and time capsule

    Printing seems to be broken on both my old time capsul, generation one, and a new airport express.  Here's what happens.
    1.  Connect printer directly to the Mac and everything prints fine.
    2.  Reconnect printer to the Airport or timecapsule.  Delete all the printers.  Power cycle everything.  Add printer.  Print and it keeps trying to connect to the printer forever.
    It use to work and it may have been a recient firmware update that broke it.  Any help would be appreciated.  I've been through all of the support documents and still nothing.  The printer is an old Epson Stylus R280.  I'm running 10.9 with all the latest drivers and updates.

    If you want to run a N speeds, run a cable from Time Capsule to Airport Express, set Time Capsule as your primary router, and turn off DHCP on Airport Express. This will create two networks, your Express will have one SSID, and the Time Capsule another SSID. One G network and one N network. Don't include the express in your network, keep it separate from Time Capsule to avoid it from coming down to G speeds. Make sense?

  • Cannot connect Airport express wireless

    Hello, cannot connect airport express wireless to linksys router.  Connected now with ethernet  cable but cannot figure wireless connection. My laptop cannot find the express while preforming setup scan, yet I'm connected to it.  I can connect with my iphone but not wirelessly. Any suggestions?

    ....I was then told over the phone that airport express will not connect to third party routers.
    This is NOT correct.
    The AirPort Express will connect to a wireless network if you know the following:
    1) The name of the wireless network
    2) The exact setting for wireless security that the network is using
    3) The wireless network password
    Most users know 1) and 3), but very few know the exact type of wireless security settings that their wireless router is using. The Express will not connect to the wireless network unless it receives all of the information listed above.
    So...we will assume that you know the name of the wireless network and the password for the network.
    Do you know the exact type of wireless security setting that your wireless router is using?  If not, the Express will not connect.
    You may need to check the setup of your wireless router....or if the router was supplied to you by an Internet Service Provider, they may be able to tell you what type of wireless security setting is being used.
    Post back when you have this info and we will proceed. There are still no guarantees that the Express will connect....but at least there may be a chance.

  • Airport express / extreme / Time Capsule Range

    Airport express / extreme / Time Capsule Range
    Can anyone please tell me what is the approximate range of Apple Airport Products.
    While doing sell in Apple store customer always ask us this question and we don't had any answer for it.
    So please if anyone has the answer do reply on this.
    - - - Akshay k. (ACMT)

    The range is about 50 meters or 150 feet.....but this assumes that the AirPort is being used in a very large open space like a aircraft hangar.....with no obstructions in the signal path.
    Chances are, your home is laid out a bit differently, so without knowing a number of variable factors like.....
    1) How many walls there will be in the signal path between wireless devices
    2) The actual construction type of the walls, ceilings, etc
    3) Heavy furniture, large mirrors, etc. in the signal path
    4 ) Other wireless networks around your home
    5) Other wireless devices like cordless phones, BlueTooth devices, etc.
    It would be impossible to tell you what the actual range might be in your home.
    In general, assuming normal modern home construction, you would not want the wireless signal to pass through more than 2 or 3 walls....since each wall will absorb on average about 15-25% of the wireless signal. A ceiling will absorb even more because of its thickness.

  • Airport Express w/Time Capsule drops connection

    I just integrated my new Time Capsule into our all-Mac network here a couple of days ago and its been fine for the most part but I've noticed that the existing airport express flashes amber for a few seconds every so often (usually once per hour or so) and disconnects everyone sharing files and connections. I have Leopard Server 10.5.2 running as well and this didn't seem to be happening before introducing Server to the mix (it was connected about 48 hours AFTER the time capsule) but the problem seems to lie with the Airport Express. Things are connected as follows:
    Cable modem --> Airport Extreme
    Airport Extreme --> 2 ethernet connections to Macs, 1 ethernet connection to Time Capsule
    Time Capsule --> 1 ethernet connection to Mac Mini running Leopard Server
    I have bridge mode set up and a couple of portables connected to it as well as an Apple TV, all of these seem to be connecting and staying connected just fine - it's the two Mac's connected directly to the Airport Extreme that get hit - the light on the unit (AE) flashes amber for maybe 2-3 seconds and I lose connection to any other macs I was connected to - I can easily re-connect with no problems at all but its obviously kind of a pain when you're working on files from the server, etc. and everything more or less locks up while OS X loses these connections.
    Does anyone have any insight into why this might be happening? I've never had any trouble with this prior to Time Capsule/Leopard Server, both of which I allowed to more or less set their own settings on the Airport Extreme figuring that it isn't too complex a set up or anything, it's not like we're a full on 20 client office here or something, just 5 total macs, no pc's, etc.
    any guidance would be greatly appreciated.

    I'm running into exactly the same problem. Configuration is the same as Jackoschild's. I get about an hour of good connection, then signal drops off and I get a rapid set of connects then disconnects. Very frustrating. I'm considering turning off the Airport on the Time Capsule and going with my 54g wireless built-in to the FIOS router it is attached to. Total of two iMacs running 10.5.2 (one 20" G5, one 24" iMac) and four PCs (Windows XP SP2) demonstrating the problem. I NEVER had a drop issue with the FIOS ActionTek wireless.
    Any solutions?

  • Airport express vs. time capsule vs. router

    What is best to do?
    My airport express is now connected to my router (speedtouch) and works very well.
    Do I connect my newly bought time capsule to my router or keep this one wireless? Because with the airport express I can make use of airplay, which I have not connected yet, but would like to do.
    I bought time capsule for wireless backup of several devices. This cannot be used a the moment, because I have to make a backup of my MacBookPro first before I update the software so that I can use the wireles backup application with my other devices.
    I do not know how to start.
    What is the effect on apple tv, none?
    How do I get the most benefit from both airport express as well as time capsule.

    We always recommend the initial backup by ethernet.. due to the time it takes and the lower reliability of wireless.
    You can either do this with the TC disconnected from the network.. and just plugged straight into the computer.. or swap the Express for the TC. I presume you are running the speedtouch in router mode so bridge the TC.. and plug the computer by ethernet directly into a LAN port of the TC.
    The above can be a permanent setup.. just tick the wireless can be extended in the TC.. and run the express in wireless bridge.. or you can also wire the express to the TC if you do not need the extra range.
    Remember the TC is faster using gigabit and designed for main router role (even if you pass that to the express). The express still only uses 10/100 ethernet.. and is designed to supplement the wireless setup.
    But there is nothing wrong with leaving the express as it is now only allow extend and then setup the TC to extend wireless from the express as that will also work well if the required connections are nearby and you can use ethernet to the TC.
    I do not know how to start.
    Have a go.. it is not like you are going to mess up. and cause something serious.
    IMO.. have a try .. do not think there is one ideal. Switch and swap.. the best is what works well for you.
    What is the effect on apple tv, none?
    It has no affect on the ATV.
    How do I get the most benefit from both airport express as well as time capsule.
    Use ethernet whereever possible.
    Avoid double hop wireless.. ie any use of extend by wireless and then another wireless hop introduces severe speed lags. Wireless cannot handle Tx and Rx at the same time.. it is half-duplex by nature. Also it is shared bandwidth.. Ethernet is superior in both areas.. every device has full bandwidth and full duplex.

  • How to extend wireless with airport express and time capsule

    So, I have a time capsule & because of the thick walls in my apartment, I can barely use my ipad and iphone at night in my bedroom! (my macbookPRO stays at 3 bars however!)
    I bought an airport express thinking I could plug it closer to or inside my bedroom to boost the signal - but it doesn't seem to work that way - any tips on how to set this up?
    TWO ADDITIONAL Qs:
    Does connecting directly to my time capsule (which i'm assuming i'd need another ethernet cable) help with the boost? (then negates the other great uses for the airport express it seems)
    Isn't there a way to do the boost with the express wirelessly? I'd really love to get wireless speakers, use airplay AND be able to use my devices just two rooms away ....   HELP!
    thanks so much (when did apple phone support start to be closed on Sundays?)
    cheers.

    Suggest that you check your setup again to make sure that the settings are correct on both the Time Capsule and AirPort Express.
    Open AirPort Utility, select the Time Capsule and click Manual Setup
    Click the Wireless tab below the row of icons
    Make sure that a check mark is entered next to "Allow this network to be extended".( If the box is not checked, the Time Capsule will not extend to the AirPort Express)
    Click Update to save your settings and close AirPort Utility
    Next, open AirPort Utility again, select the AirPort Express and click Manual Setup
    Click the Wireless tab
    Settings should look like this:
    Wireless Mode = Extend a wireless network
    Wireless Network Name = Same name as the Time Capsule network
    Check mark entered next to "Allow wireless clients"
    Wireless Security = Same setting as the Time Capsule
    Wireless Password = Same password as the Time Capsule network
    Confirm Password
    Update to save settings and close AirPort Utility
    Locate the AirPort Express approximately half way between the Time Capsule and area that needs more wireless coverage. You may need to experiment on placement to find the best compomise.
    Post back on your results.

  • Airport Express with Time Capsule: How does it work?

    I don't know much about newtorking but wanted to ask this:
    I am considering buying a 1tb Time Capsule. I use Airport Express now so I can stream iTunes to my home entertainment system. Is the configuration supposed to be this? See below:
    -Plug the Time Capsule into the cable modem for internet access
    -Plug the APE into the Time Capsule with (ethernet? USB?) to power its Air Tunes capabilities
    I would love to gain the back up and simplicity of Time Capsule but I am not giving up Air Tunes.
    Any replies appreciated. Thanks.

    So it sounds like I should just leave Airport Express as my networking hub/internet connection point, and let Time Capsule acquire a spot on the network, then I can access it that way.
    I guess I thought that Time Capsule had to be the primary router/internet connection for the network, and Airport Express would become sub to that.
    I think I prefer the first option over my idea.
    Thanks for the response.

  • How do I connect Airport Extreme and Time Capsule to my new iMac so that AE is used for network and TC only used for Time Machine backup?

    I didn't realize that Time Capsule will only support the print function of a wireless multifunction printer.  So I want to use Extreme for my network to have full use of my printer and use TC as the Time machine backup only.  How to I make the connections?

    Thanks for your response and this is getting complicated but I just purchased a new iMac as well as the Airport TC.  I've had the Airport Extreme for a year or so.  The Airport Extreme worked perfectly with my old iMac wirelessly and I had all functions of my printer with no problems.  I was expecting the same with the TC.  But the instruction that came with TC say to connect the printer to the TC via USB...which I did.  And the print function worked perfectly but nothing else.  In researching I discovered that when wired that way the TC only supports the print function...not scan or fax or anything else.  I tried going wireless since my AE worked perfectly via wireless but I got no printer functions at all that way.  But I'm wondering also if I tried that during a time I was having other issues...I had to delete and re-add my printer which solved some other problems.  I may try that again...and see if I can get all print functions with just the TC connected
    As far as connecting both your AirPort Extreme and Time Capsule on your network, we're not clear on exactly how you want to do this.  Will the AirPort Extreme connect to your modem using an Ethernet cable and the Time Capsule connect to the AirPort Extreme using an Ethernet cable?.......or......do you want the Time Capsule to connect to the network using wireless?
    Well... first of all I would like not to have to use the AE at all...I would prefer using just my TC for network, all print functions and Time Machine backup if that's possible. My printer will not accept Ethernet connections (Canon MX512).
    After failing at getting this to work, I decided I would try to use my AE for net and print functions and just use my TC for Time Machine backup.  I tried several different connection configurations with no success until finally I connected cable modem to my AE via Ethernet and went wireless with the AE and printer. but connected the AE to the TC via Ethernet and amazingly everything worked like a charm (for a while) and I was patting myself on the back for being so smart.  But now I find that the connection only lasts for a short time.  If I leave it for a while the TC goes invisible...or at least I see a message saying the Ethernet is unplugged...but it is not... and I lose internet connection even though I have a green light on my AE. So now I'm at a loss. I don't know why I keep losing network signal and why my system thinks the Ethernet is unplugged.
    So... after all this...I figured I wasn't so smart after all and I must have things wired incorrectly.
    So... it sounds like you are saying I should go back and try again to get my new TC to work as I want it to via wireless instead of connecting via USB...is that correct?  Could you tell me exactly how I should wire my equipment from cable modem to AE and/or TC to achieve net capability, full functions of my printer and Time Machine backup...
    Thanks...

  • Cannot connect Airport Express N to Dual Band Time Capsule at N speed

    Long time reader, first time poster. I am usually pretty good at solving my problems without posting, but I have been attempting to solve this problem for a while without success, so here it goes.
    I have a dual band Time Capsule that I want to run at 5Ghz N and 2.4GHz b/g/n (using the OPTION key when selecting "Radio Mode" to select this option). This runs fine on its own. However, I also want to set-up a new Airport Extreme N to run as an extender for the 5Ghz network, and here is where I have problems.
    I have already set-up the 5Ghz network to be under a separate SSID. I have also selected to use Wide Channels, Multicast Rate=High, and Transmit Rate=100%. I have also been sure to make sure that I have selected "Allow this network to be extended" in the TC. As of yet, I have not even attempted any WEP/WAP key security, and the SSID is visible.
    When I attempt to connect the AEx as a repeater (using the "Extend a wireless network" option on the AEx) the AEx will not see the 5Ghz network name. It will only allow me to select the 2.4Ghz SSID, even though I have a distinct SSID for the 5Ghz.
    Note: both my iMac and my AppleTV can see and connect to the 5Ghz network. I am attempting to set-up the AEx right next to the TC before attempting to see how faraway I can move it.
    I have additionally tried to set-up the AEx to repeat the 2.4Ghz network. In b/g/n mode it will repeat, however it only ever seems to get the g speeds. If I set-up the TC to only do N networks (ie one SSID as the 5Ghz N Network and one SSID 2.4Ghz networks) the other clients (the iMac and the AppleTV) can see and connect to each, however the AEx won't connect at all.
    What am I doing wrong? I feel that I have been very thorough with my approach. Any help would be very welcome.

    Welcome to the discussions!
    I don't have a solid answer yet to your issue, but would offer a few comments that might help sort things out.
    I'm confused by your statement that you are able to extend the 2.4 GHz network, because the dual band TC does not allow the guest network to be extended. Check AirPort Utility - Manual Setup. Click the Wireless tab. I don't have a dual band TC, but I believe if you click the Options button, you will see more info about extending.
    While there is a check box next to "Allow this network to be extended" for the main network, there is not a check box for the "Guest" network. It's not there, or least it's not there in the guide that I'm looking at.
    I suspect that your computer was picking up the 2.4 GHz network from the TC, not from your Extreme. To verify this, open AirPort Utility again and click on Manual Setup for the TC. On the summary page, note the MAC address for wireless on the TC. Now, do the same thing for the Extreme.
    Use your computer now to check things. Hold down the option key and click on the Airport icon at the top of the screen. The MAC address of the device that you are connected to will be displayed.
    Have you tried to move the Extreme to a more remote location? You note that you have the two devices, TC and Extreme very close together. As a test, position the Extreme approximately half way between the TC and the area that you want to extend to and see if you can connect with your computer. Check to see if your computer is connecting to the Extreme or the TC by holding down the option key as above.
    You have probably already done this, but check on the setup for the Extreme using AirPort Utility - Manual Setup - Wireless tab. There is a check box either on the Wireless page or the Options page to "Allow wireless clients". This must be checked for wireless clients to be able to connect to the the Extreme.
    Post back with your findings and we'll try to figure this out.

  • Airport Express and Time Capsule connection issues

    I have the following setup:
    - Airport Express set up as 'create a wifi network' with the exact same name and password as my main network from my BT router
    - Time Capsule setup to 'join existing network' which is the same name - obvioulsy! - as the other two.
    Everything worked OK until fairly recently. My MBP which usually is connected to the AE n/w accessed the TC via Time Machine OK, and my iMac backed up via TM to the TC OK as well.  Now, however, the TC (which is situated in range of both the AE and the main router) seems to connect sometimes to the (weaker) AE and sometimes to the (almost adjacent) main router.
    If it connects to the main router network, my iMac backups are OK, but if it connects to the AE network, then TM just fails with the usual 'backup disk cannot be found' even though it is clearly visible in Finder.
    Is there anyway of locking the TC into a particular network?

    OK, thanks for the information.
    Temporarily, disconnect the Ethernet cable from the AirPort Extreme to the Time Capsule's WAN port.
    Close AirPort Utility 6.1 on the Mac if it is open
    Start over by holding in the reset button on the back of the Time Capsule for 9-10 seconds, then allow 60 seconds for it to restart to a slow, blinking amber light
    Connect the Ethernet cable from the AirPort Extreme to the WAN port on the Time Capsule
    Click the AirPort icon at the top of the Mac's screen and wait a minute for the heading of New Apple Base Station to appear. Under that,  click on the Time Capsule.
    AirPort Utility will open automatically and take a minute to analyze the connection. After a minute, it will display a message that the network will be configured to "Extend".
    Enter a name for the Time Capsule and click Next
    AirPort Utility will take another minute to configure everything.  When you see the message of Setup Complete, click Done.
    You should now be able to connect to the Time Capsule wireless signal.

Maybe you are looking for