Cannot connect devices using Extend Network via Ethernet

Hi
I have been going nuts with this issue, and cannot seem to find any solutions. PLEASE HELP!
I have an Airport Extreme (pretty new and all up to date) connected to my modem. Everything works perfectly. The wi-fi is great, all devices can connect without any issues so nothing is wrong here. The Airport extreme is dishing out the IP addresses etc. The Airport extreme is in the lounge.
I purchased a new airport express yesterday. I put it in my study, far away from the lounge. I connected the airport extreme to the airport express using an ethernet cable. I plugged it in, and set it up to extend the wireless network via ethernet. I.e. it is set up in bridged mode and set up to 'create a wireless network' with identical name password etc. Everything is good. It reboots and the light is green. in the Airport utility everything shows up correctly.
Here is the problem., The second that any device (lets say iphone) moves from the lounge to the study, and tries to 'jump' to the stronger network provided by the express, it kills the ENTIRE network. The following happens:
1. The iphone loses wi-fi signal immediately. If I go into wi-fi settings, it sees my netwrok with FULL strength, but just remains in the 'spinning ball' state trying to connect. Seems to me that the express is unable to hand out an IP address or something.
2. If i open the airport utility on my Imac (in the study), the airport extreme has a yellow warning light and cannot be found via ethernet OR wi-fi. (The Imac is also Hard Wired from the Airport extreme in the lounge).
THe whole system requires a re-boot in order to work again.
If I re-boot the system, and leave a device near the airport express, it immediately receives signal, gets an IP address, and has an internet connection. Going back to the lounge causes no issues, it doesnt drop signal and still connects to the internet via the extreme. But as soon as I walk back into the study again - BOOM, everything drops.
I only purchased the new express because i was having EXACTLY the same issue with an older Airport extreme. No matter what I do, it just wont work via ethernet. I have tried all manner of settings. The ONLY setting that seems to work is to extend the wi-fi network. However, the rooms are too far apart, and this will require a third station in the middle, which i want to avoid (by the time the wifi network is extended across 3 decvices it is too slow).

Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?
Yes. But, it is the AirPort Express that would "pick up the wifi". Then, you would connect an Ethernet cable from the AirPort Express to the PC.
Configure the AirPort Express to "Join a wireless network" and click the option to "Enable Ethernet clients" during the setup to activate the Ethernet port on the device.
I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
There is a good chance that your printer will work connected this way, but you won't really know until you try.

Similar Messages

HT4259 how to configure extended network via ethernet

how to configure an extended network via ethernet

I assume that the Express is new, so that it still has the factory default settings.
Connect an Ethernet cable from one of the LAN <-> ports on the AirPort Extreme to the WAN "O" port on the AirPort Express
Power up the Extreme and Express if they are not already powered up
Open Macintosh HD > Applications > Utiltities > AirPort Utility
Click on the tab in the upper left hand corner of the window that reads Other AirPort Base Stations (1)
Click on the AirPort Express xxxxxx
Wait a minute or two while AirPort Utility analyzes the network and then announces that the Express will be configured to extend your network
Enter a name for the AirPort Express and click Next
Wait 2-3 minutes while AirPort Utility configures the Express and the Express restarts
When you see the message that setup is complete, click Done
That's it.

Using Time Capsule to Wirelessly Receive Internet and then Extend Network via Ethernet

Hello,
Our modem/router combo is located downstairs, and my computer that i want to get online is upstairs. I cannot get a ethernet from the modem to my computer to access the internet, so I wanted to try to use my Time Capsule to help me get online upstairs (not sure if this is possible...)
My idea was to have the Time Capsule receive the wireless signal and then connect the computer to the Time Capsule through an ethernet so that I may get the computer online. Essentially wireless connection in, wired connection out.
I've been playing around with the device for a while now, and can't seem to make this work. Has anyone used the Time Capsule in this fashion? Is it even possible? If not, does anyone have any suggestions on how to get my computer online?
Thank you very much for any help/input!!

Why not try a pair of these over domestic power loop.
http://www.netgear.com/home/products/powerline-and-coax/high-performance/XAVB510 1.aspx#two
Not cheap though Best buy link
http://www.bestbuy.com/site/NETGEAR+-+Powerline+Ethernet+Adapter+Kit/5042106.p?i d=1218603011817&skuId=5042106
The Apple solution might well need Two devices to extend range.
You would retain your ISP router/modem however would go into settings and TURN OFF wireless on that device - you can do this in the Java Web based control panels on most routers.
Now you sling the Ethernet cable between that router and a purchased Time Capsule device locally and set this up to create a new local Wifi network (Replacing that of the ISP supplied router) . Being a dual band device and being able to broadcast both over 2.4 Ghz and 5 Ghz frequency base bands simultaneously you could well see improved performance and range straight away.
However if not then you are going to need a further device an Airport Express set up in bridged mode somewhere between the Time Capsule and your upstairs rooms. Your may have to try various power points and locations to get coverage required.
Further Airport Express devices can be added in bridged mode as required to cover blind spots, however remember each additional device degrades the overall network performance somewhat.
Again this will get quite costly.

Use Airport Express Brick N to extend network via ethernet

I have the old brick-style Airport Express N model, which I'm currently using to extend the newer Airport Express hockey puck. The hockey puck is setup to with DHCP and creating the network. The brick is in setup to extend the network using DHCP and in Bridge Mode. When I plugin the Ethernet cable from the Ethernet port of the hockey puck to the brick, I lose all internet connectivity. I seem to recall reading some documentation that said the brick would support ethernet rather than just over-the-air. Thanks for your help!

My question is: can I connect the two via ethernet cable to the extending is happening over the air? I'm not sure the brick is capable of this?
It is possible to "extend" in two different ways:
1) Extend using a wireless connection between the AirPorts. Apple calls this "extend using wireless" during the setup. When you extend this way, about half of the potential speed on the network is lost.
2) Extend using a wired Ethernet connection between the AirPorts. Apple calls this "extend using Ethernet" during the setup. When you extend this way, full bandwidth on the network is maintained since there is no signal loss in a wire.
If you want to "extend using Ethernet", the 2nd Gen AirPort Express must be the "main" router, so you will need to reconfigure it for that purpose. The 1st Gen will also need to be reset back to default settings and reconfigured as well.
Once the 2nd Gen Express is working correctly as the main router, connect an Ethernet cable from the LAN <--> port on the 2nd Gen Express to the Ethernet port on the 1st Gen Express and use AirPort Utility for the setup.

Trying to extend network via ethernet

Trying to add another Extreme to our network to assist with the number of wireless clients on our existing Extreme. Trying to add the 2nd Extreme via Ethernet and extend the same network SSID and all other info.
After setting up and adding it shows that it is extending via wireless, and when connecting to the WAN or LAN ports it wants to take the entire network down.
Using 5th Gen Extreme. Airport Utility 6.2, and all devices have 7.6.3 firmware. Already have 2 Express units on the system extending the network wirelessly where we do not have Ethernet ran. Those have been working for over a year.
Any thoughts on what we are missing when setting this up where we can't plug another Extreme in via Ethernet? In the setup I don't see an option for extending via ethernet.....

Close AirPort Utility if it is open
Disconnect the Ethernet cable to the new AirPort Extreme
Hold in the reset button on the back of the AirPort Extreme for 7-8 seconds and release. Allow a full minute for the AirPort to restart
Make sure that the Ethernet cable is connecting from a LAN <-> port on the "main" router to the WAN "O" port on the new AirPort
Click the AirPort icon at the top of the Mac's screen and wait a minute for the heading of New AirPort Base Station to appear
Just below that, click on the AirPort (an AirPort Express is pictured in the example)
AirPort Setup will open automatically and take a minute to analyze the network....then announce that the AirPort Extreme will be configured to "extend" your current network.
Enter a device name for the AirPort Extreme and click Next
AirPort Setup will take a minute to configure everything for you. When you see the message of Setup Complete, click Done
Test the network and report on your results

Airport express won't extend network via ethernet but shows GREEN (HELP!!)

I have the following routers setup up the same network and are working.
10.0.1.1 Airport Extreme (connected to hardline from IP)
10.0.1.2 Time Capsule 1 (extending network and providing internet connection to computer via ethernet)
10.0.1.3 Time Capsule 2 (extending network and providing internet connection to Xbox1)
10.0.1.4 Airport Express 1 (extending network and providing internet connection to Xbox2)
Not working correctly
10.0.1.43 Airport Express 2 (wanting to set this router up to extend network to plug into desktop)
The router seems to join the network fine and will show GREEN but doesn't show a similar IP address as the rest of the routers. It also doesn't provide any internet connection via ethernet to any computer, the network pref page says that it shows RED and that nothing is connected to the computer for internet but airport shows GREEN.
Reset the router multiple times, tried every which way of setting it up and no go. I also tried assigning it a IP and not using DHCP and gave it a 10.0.1.5 and still the same outcome.
Right now just at complete loss as to what to try next.

Sorry, the older version of the Express does not have the option to "extend a wireless network", which is the setting on the new Express that provides more wireless coverage and also enables the Ethernet port.
What you want to do can be done with a different setting..."participate in a WDS network" on both the Time Capsule and Express, but I am not recommending that you do this because WDS operates only in "g" wireless mode. Your Time Capsule would lose most of its performance in this setting and the network would slow down tremendously...defintely not what you want for gaming.
You'll have the best performance if you connect the PS3 directly to one of the Ethernet ports on the Time Capsule using an Ethernet cable. If it is not possible to run the cable, the next best performance option would be to use a pair of Ethernet powerline adapters to send the Ethernet signal over the existing AC wiring in your home.

Connect MacBook to wifi network via Ethernet

I am looking for a way to connect my MacBook to my wifi network via my Ethernet port. I'm not having any trouble with the wifi but am looking at getting an apple tv and wish to be able to use wolan. As far as I know, wowlan is only available using the apple airport routers. Is there something I can get that plugs into my Ethernet port on my MacBook, connects to the wifi network and lets my MacBook treat it as a wired connection so I can use wolan? I assume something like this would. E cheaper than buying an apple router that supports wowlan...?
Also, how do I make sure that my current router actually supports wolan?
Thanks.

We assume that you are trying to configure the AirPort Express to "join" your wireless network. In order to do so, you must enter in the wireless network name, exact type of security and password that your network is using.
Mistakes are often made with the security settings because different manufacturers use different nomenclature to mean the same thing. For example
WPA2 Personal on Apple = WPA2-PSK-AES on other wireless routers
or
WPA/WPA2 Personal on Apple = WPA-PSK-TKIP on other wireless routers
Can you dig a bit deeper into your settings on your router to find out whether you are using AES or TKIP? Once you find that info, you should be able to match up the correct setting on the AirPort Express during the configuration.
Don't be fooled by the the message that you see when you click Update during the configuration process. The message states something to the effect that the settings have been stored successfully on the AirPort Express. What it doe not tell you is whether the settings that were stored are the correct settings.
You will know that you have the correct settings when you see a green light on the AirPort Express 40-45 seconds after you click the Update button.

Using airport express to extend network via ethernet socket

I have a wireless router set up which feeds my mac and tv (via a wired ethernet connection). I have also a pc which doesn't have wifi capability.
Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket? I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
Thanks

Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?
Yes. But, it is the AirPort Express that would "pick up the wifi". Then, you would connect an Ethernet cable from the AirPort Express to the PC.
Configure the AirPort Express to "Join a wireless network" and click the option to "Enable Ethernet clients" during the setup to activate the Ethernet port on the device.
I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
There is a good chance that your printer will work connected this way, but you won't really know until you try.

I just got an iPad 2 16 gb and was wondering how I can upload pictures from a micro sd card but my iPad is saying cannot connect device using too much power. I have tried a 16 gb micro sd card and 4 gb micro sd card. Can anyone help please??

I got an iPad 2 and I cannot get my pictures to upload from a micro sd card as the iPad is saying device not accepted using too much power. Can anyone help? My iPad 2 is a 16 gb and my micro sd card is 4 gb

You can use a USB flash drive & the camera connection kit. First download the pics to your computer.
Plug the USB flash drive into your computer & create a new folder titled DCIM. Then put your movie/photo files into the folder. The files must have a filename with exactly 8 characters long (no spaces) plus the file extension (i.e., my-movie.mov).
Now plug the flash drive into the iPad using the camera connection kit. Open the Photos app, the movie/photo files should appear & you can import.
 Cheers, Tom

How to configure extended network via ethernet

i have a airport extreme and i need to connect my airport express using ethernet cable.
what should be the configs in the airport extreme to get this done?
thank you.
mauro

Please answer my questions on your other post so that we can help.

I CANNOT PRINT FROM MY IPHONE 4 TO MY BROTHER 8890DW PRINTER WHICH IS CONNECTED TO MY TIME CAPSULE/NETWORK VIA ETHERNET CABLE???

Why can’t I print from my iPhone 4 to my brother 8890dw printer which is connected to my time capsule/network via ethernet cable??? My iPhone does not even locate my printer,even though I have no problem printing from my Mac to the same printer.

Typing in all caps indicates shouting, is considered rude and is difficult to read. Many simply do not read such posts.
You would need an airprint enabled printer or an app that proides printing function.
iOS: AirPrint 101

Network mode: Create a wireless network vs. Extend wireless network via ethernet

Can some one tell me the difference between configuring AirPort Utility : Network mode: Create a wireless network vs. Extend wireless network via ethernet? I connect my cable modem to my Airport Time Capsule to a network switch via ethernet. The switch contacts to three Airport Express (AE connects to two Apple TVs via Ethernet) and another TC. Which is the best mode to configure my network?
Thanks

Create a wireless network is used only when the Airports have an Ethernet connection. If you are using the setup wizard.....the setting will read Extend using Ethernet during the setup. If you go back in using AirPort Utility to check the Network Mode setting.....you will see that it is really Create a wireless network.
Extend a wireless network is used only if an AirPort is connecting to another AirPort using wireless.......not Ethernet.
Every one of the Airports on your network must be configured to Create a wireless network.
If you do connect an Ethernet cable to an AirPort that is already set up to Extend a wireless network......that will create a massive feedback loop that will crash the network until you remove the Ethernet connection to the device.
The bottom line here might be if you are using the setup wizard, it will make the correct choice for you.

Wired Connection to An AE that is extending network via wifi

I have 2 Airport Extremes. The first is a 2nd Gen model the other is a 4th Gen.
The 2nd Gen model is connected to our modem and has made a working home network for a number of wired and wireless devices.
I also have an older mac pro with no wi-fi card installed. What I'd like to do is use the 4th gen Extreme to connect to the Mac Pro via ethernet to get the mac pro on the network via the wifi Capability of the Extreme.
Using one of the other computers I have been able to configure the 4th Gen to extend the network via wifi and other wifi macs can see it on the network and it appears to be working as expected but when I connect the old mac pro I get no networking or internet through it.
The mac pro's network control panel shows it as being connected through wi-fi even though it is actually an ethernet cable into the 4th gen AE. Selecting ethernet gets me nothing. The mac pro also doesn't seem to be getting the correct IP addresses.
Is there an incompatibility between the 2nd and 4th gen models that I'm unaware of that won't let them do this?
Just to reiterate I'm trying to go:
Modem---> 2nd Gen Extreme---> Via WiFi to ---> 4th Gen Extreme ---> Mac Pro's Ethernet.
Can it be done?
Thanks

In order to enable the Ethernet ports on the 4G Extreme for the Mac Pro, both AirPorts need to be configured for an extended network. Please read through the steps provided in the link to see if you may have missed any steps.

Mac Pro no longer connects to network via ethernet.

Since coing back from Thanksgiving break and my Mac Pro 1,1 will no longer connect to my router through via ethernet. This means I can neither connect to internet nor connect to devices like my laptop and Apple TV. Strangely, I can still connect to my Mac Pro from these devices to share screen, play audio/video through iTunes, etc. In Network Settings, I still have a green dot, and I still get an IP address assigned (though I usually use a fixed IP). If I go into my router (Netgear WNDR4000), the router tells me that the Mac Pro 1,1 is connected to the network.
I already have tried the following solutions:
· Restarting router, modem, and computer
· Making a new location in Network Settings
· Trying different ethernet ports
Please Help!

Your local LAN runs through your router.
All your ethernet ports, and your modem and router, should be behind and filtered from excess current. That means a UPS generally. And run input line thru UPS (coax) first, then run RJ45 back through UPS again (there can still be excess surge or current on the line).
Modems and routers can be compromised by surge outage or storm. So can ethernet ports.
You have two ethernet ports and you tried with both also.
What you did not do that I would have added is SMC Reset / Reset NVRAM/PRAM.
This is what I have had for the last year, very nice and stronger signals thruout the house.
http://www.amazon.com/NETGEAR-Wireless-Router-Gigabit-R6200/dp/B008HO9DIG/

I want to transfer files from a Win XP PC to a Mac using Time Capsule via Ethernet connection. Is this possible?

I want to transfer files from a Win XP PC to a Mac using Time Capsule via Ethernet connection. Is this possible?

Sure.. the PC connects by SMB.. the Mac connects by AFP or SMB..
But you can simply share SMB directly from the Mac.. there is no need to copy files through the TC. Go to system preference, sharing, and turn on SMB for the folder you want to share files to / from on the Mac.
Make sure you have a common username and password also helps.
If you have a TC already can you copy files to it via the windows machine??

Cannot connect devices using Extend Network via Ethernet

Similar Messages

Maybe you are looking for