Cannot connect more than 1 mac to internet?

when connecting to inernet via Time capsule, i can only connect 1 of my 3 macs to internet? used to work, now with new internet provider only 1 connects.
what to do....
thanks,
Frank

Check your settings on the Time Capsule using AirPort Utility - Manual Setup
Click the Internet icon and make sure that your settings look like this:
Connect Using = Ethernet
Connection Sharing = Share a public IP address
Update to save settings, then power off the modem, Time Capsule and all of your network devices....order is not important
Wait 15 minutes
Power up the modem first and let it run 2-3 minutes by itself
Power up the Time Capusle the same way
Power up each other device one at a time about a minute apart
Check for proper operation.

Similar Messages

Airport extreme cannot connect more than one computer

Hi,
I just got a new cable internet connection but have major problems with my airport extreme. I can be online via airport but I can not connect any other devices wirelessly (including other laptops).
The connection works only when 'distribute a range of IP addresses' is selected in airport utility. Choosing 'share a public IP address' results in no internet access whatsoever. I tried soft- and hardresetting the base station with no luck.
Any ideas?

It sounds like your cable modem needs to be reset.
Most cable modems require that you power them off/on whenever you switch the Ethernet connection from one device to another. When the cable modem is powered on, it finds the new device and talks to it.
Some cable modems have a button on the back to do the reset. Some cable modems have an internal battery which must be removed to do the reset. Some cable modems must be off overnight (or at least several hours) so that equipment back at the ISP can be reset.
"Share a public IP address" is the setting that you want to use.

Connecting more than one ipod to one mac computer

Can anyone please advise me on how I can connect more than one ipod to just the one mac computer. I need to set up 3 ipods to work on the one mac computer but each with there own itunes library. thanks

When the iPods belong to two users, there are a couple of recommended methods for using more than one iPod on a single computer. Method one is to have individual Mac or Windows user accounts which by definition would give you completely separate libraries. Each account has it's own iTunes folder, Library and iTunes Music folder and you load it with CDs etc just as you did with your original one. Each iPod can be set to update however the owner chooses, sync all, manual or sync specific playlists.
Method two is to set your preferences so that either one or both iPods get updated with only certain playlists within one library. Have a look at this article and see what you think and go for whichever you feel suits your needs best: How To Use Multiple iPods with One Computer
Another option when using a single library is to set one or both of the iPods to manual update: Managing content manually on iPod
Choosing the update option "automatically update selected playlists only" (called Sync Music - Selected playlists in iTunes 7) allows you to create a playlist specifically for each iPod and drag the tracks you want into it. If you tire of the list and want to change it, you just add or remove the songs you don't want. The ones you take out out remain in the library to be used by the other iPod. Make your playlist a Smart playlist and limit the size to just below the advertised capacity of your iPod ( for example, around 3700MB for a 4GB or 1800MB for a 2GB Mini or Nano). You can read more about playlists at these links:
iTunes: Creating playlists of your favorite songs
How to create a Smart Playlist with iTunes

Hello! I have in my home 2 iMac, 2 iPad, 2 iPhone, and 1 air base extreme. I don't succeed to connect more than one divice from similar type. I tried everything what I knew. I build another network, etc...

Hello! I have in my home 2 iMac, 2 iPad, 2 iPhone, and 1 air base extreme. I don't succeed to connect more than one divice from similar type. I tried everything what I knew. I build another network, etc...
So only one imac, only one ipad..and so on simultain.
More over, all the divices are conect through wifi to air base but are not receiveing internet as i told above.
I need to disconnect one device to have internet on the second one from the same type!
Could somebody help me?
Many Thnaks,
dan

If your network configuration is:
Cable modem > (Ethernet cable) > [WAN] AEBS > (wireless) > Macs, then
AirPort Extreme Base Station Setup (AEBS) w/High-Speed Cable Modem
Modem/Router Power ReCycling
- Power-off the Cable modem, AEBS, & computer(s). (If possible, leave the modem off overnight.)
- Power-on the Cable modem; Wait at least 30 minutes.
- Power-on the AEBS; Wait at least 5 minutes.
- Power-on the computer(s)
Perform a "hard" reset of the AEBS.
- (ref: http://docs.info.apple.com/article.html?artnum=107451)
Setup the AEBS
With the network components powered down, set up the AEBS, using the AirPort Admin Utility, connect your computer directly (using an Ethernet cable) to the LAN port of the AEBS, and then, try these settings:
AirPort tab
- Base Station Name: <whatever you wish or use the default>
- AirPort Network Name: <whatever you wish or use the default>
- Create a closed network (unchecked)
- Wireless Security: Not enabled
- Channel: Automatic
- Mode: 802.11b/g Compatible
Internet tab
- Connect Using: Ethernet
- Configure: Using DHCP
- WAN Ethernet Port: Automatic
Network tab
- Distribute IP addresses (checked)
- Share a single IP address (using DHCP & NAT) (enabled)
Once you verified that you can get Internet access for all of your computers, you should secure your wireless network. To do so, I suggest that you make these changes:
AirPort tab (optional)
- Create a closed network (checked)
Change Wireless Security
- Wireless Security: WPA Personal
Base Station Options - WAN Ethernet Port
- Enable SNMP Access (unchecked)
- Enable Remote Configuration (unchecked)
- Enable Remote Printer Access (unchecked)
Wireless Options
- Transmitter Power: 10%
Access Control tab (optional)
- + <add the computer(s) that will access this wireless network>

IChat AV with NAT and more than one Mac

I am a bit confused about firewall settings for iChat AV. I have a netgear FVS328 router. Obviously to have iChat working, I first open the firewall on my mac (Tiger) for the appropriate ports. Then I defined a service on the router and a rule to open those ports. It works... however, I have an issue.
In the router firewall setup I had to give an LAN IP Address to which packets for those specific iChat ports would be forwarded. Now, I understand this when a connexion is ignited from the Internet and (for example) you would want all HTTP trafic on port 80 to go to your web server. But here I have more than one mac behind my firewall. Moreover, they get there address by DHCP. I can't change the firewall setting each time I want to chat from a different computer!
I tried to have a look at port triggering, but it doens't seem to exist on the netgear. But even though, I would have to specify an IP address on my LAN.
Why is this needed since basically both iChat parties are already connected to .Mac so the connexion is made!
I am also wondering how they manage that kind of problem in Internet cafes where they certainly do not have a fixed Internet IP address for each PC or Mac available!

It is not possible to port forward the same port number to more than one computer on any router that does NAT. It is impossible for the router to know which of the computers to send it to and sending it to both would confuse the software.
Think of it another way all post for a particular house is delivered by a postman. Once posted in the mailbox someone picks it up and ensures it reaches the correct person by the name written on the post. Now if you have 2 John Smiths in the same house nobody will know which one it is for. The same applies to the port numbers on the router. Some applications allow you to select a unique range of ports for each computer so you can organize a unique port for each computer but iChat doesn't.

IChat with NAT for more than one Mac?

I am a bit confused about firewall settings for iChat AV. I have a netgear FVS328 router. Obviously to have iChat working, I first open the firewall on my mac (Tiger) for the appropriate ports. Then I defined a service on the router and a rule to open those ports. It works... however, I have an issue.
In the router firewall setup I had to give an LAN IP Address to which packets for those specific iChat ports would be forwarded. Now, I understand this when a connexion is ignited from the Internet and (for example) you would want all HTTP trafic on port 80 to go to your web server. But here I have more than one mac behind my firewall. Moreover, they get there address by DHCP. I can't change the firewall setting each time I want to chat from a different computer!
I tried to have a look at port triggering, but it doens't seem to exist on the netgear. But even though, I would have to specify an IP address on my LAN.
Why is this needed since basically both iChat parties are already connected to .Mac so the connexion is made!
I am also wondering how they manage that kind of problem in Internet cafes where they certainly do not have a fixed Internet IP address for each PC or Mac available!

HI Alexander,
This page shows the set up for Port Forwarding for just the login/Text chatting port.
You may be able to repeat this for another IP address (depends on device if this is allowed).
You also have to repaet the process for the other 22 ports
These are all on UDP (5060, 5678, 16384-16403) The group of twenty ports at the end may have to be entered one at a time
Port Triggering is a method on some routers and modems that has data arriving on one port Trigger the opeing of other ports. I can not see that you have it from the Pics in the link. (newer Firmware if available may have it).
ANother option on some devices is UPnP where the ports are opened by the Application when they are needed.
Both UPnP and Port Triggering Allow for multiple computers to use the same ports.
Ralph
Ralph

Cannot run more than one instance of a remote app in remote desktop services Server 2012

All,
I installed "Remote Desktop Services (RDS) Quick Start Deployment for RemoteApp, Windows Server 2012 Style" using the instructions here http://blogs.technet.com/b/yungchou/archive/2013/02/07/remote-desktop-services-rds-quick-start-deployment-for-remoteapp-windows-server-2012-style.aspx
I need to set up an image viewing program (Olyvia) to allow students using Macs and iPads access to this windows only application in order for them to get their work done. We may have 12 or more students accessing and trying to run the Olyvia application
at any one time.
All works good, except that I cannot run the Olyvia application (setup as a remoteapp program) more than one instance at a time. That is, when I start up "olyvia" on a Mac, it works great. If I leave it up and running, and then try
and start up "olyvia" on an iPad (using different accounts), I get the following error message:
"Cannot run more than one instance of this program simultaneously. Either the program is already running, or it has not been terminated completely."
I need to understand the root issue.
1. Is this a licensing issue? So, I need to add some CALs to the RDS server?
2. Is this a application issue with "olyvia"? So, no matter what I do, it is not going to be able to be used by more than one person at a time when configured as a remoteapp?
3. Did I not "publish" the application correctly?
4. Is this happening because I followed the "quick start" guide?
Appreciate any help I can get on this. We have no problem getting CALs, I just need some help with the root issue.
Thanks,
Geoff Weatherford
CVMBS, CSU

Hi Geoff,
Each application uses different techniques for determining if multiple instances are running. If you can determine what method it is using then perhaps you could use App-V or other virtualization software.
In the best case you really should direct your question to the maker of Olyvia. The reason I said that is they specifically designed their software to prevent multiple instances, so the first question is, why? Is it related to Licensing?
Compatibility? If you knew the specific reason(s) why they are doing it and the technique used then at the point using a virtualization technique may be the best option.
-TP

Can I back up more than one mac to the time machine:

Can I back up more than one Mac to a time machine? I have a laptop and a Mac Desktop computer can I back up both on the same Time machine

Absolutely.
However, quoting from ASC contributor Pondini's excellent Time Machine FAQ:
It is advisable, though, to partition an external disk that will be connected to your Macs into one volume for each Mac ...

Cannot open more than one photo in Photoshop

Hi
I don't know if anyone can help me, but I am having an issue with Photoshop CC (2014), I cannot open more than none photo at a time, and keep getting the attached error.
It has been working fine, until i have tried it this evening.
Regards
Mick

There's something wrong with your system.
Please give detailed information.
BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
A screen shot of your settings or of the image could be very helpful too,
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

Can't connect more than one device.

I just bought an Airport Express 2 gen from a friend and I have two issues: I tried to reset it to factory settings and could not do it. Tried holding the reset button for 10 secs, unplugging and plugging back in while holding the reset button, holding the button for a longer time and nothing worked. I had no choice but to create another network. Once created, I can't connect more than one device. If I have my MacAir hooked up the network and I try to get my Ipad in, the minute I type the network pass in my Ipad, a screen pops up where I have to log in with my internet provider account. When I do that, it will connect, but my MacAir will disconnect automatically.
Appreciate any help!

Things are a bit different with the 2nd Gen AirPort Express and other newer AirPorts.
A Factory Default Reset is now the same as what was previously known as a "Hard Reset".
Power up the AirPort Express and let it run a few minutes.
Hold in the reset button on the Express for 10 seconds
Release the reset button and allow a full minute for the Express to restart to a slow, blinking amber light
If the Express is operating correctly, it will be back to factory default settings at this time.
If you try the reset a few times and the Express will not return to default settings, the Express is defective.

Can Not Connect More Than One Device

Does anyone else have the issue of not being able to connect more than 1 device to your wireless network without it timing out and resetting the router? I pay extra to have what they say is the fastest internet but it never works. If Apple TV is streaming Netflix my iPad, my laptop and my desktop all have to be off and not connected to the WiFi or the router resets itself. My speed test actually timed out because it was taking so long both times I tried it, a month apart. I had the same issues before switching to X1 and getting my new WiFi modem. If I call I just get the run around and have my modem reset a dozen times with the exact same outcome...

It would help if you post the model of the device.
Also look over the troubleshooting tips and post the downstream RF power levels, downstream SNR and upstream power levels on all channels.
http://forums.xfinity.com/t5/Basic-Internet-Connectivity-And/Connection-Troubleshooting-Tips/m-p/1253575#U1253575

Error: 1012704 Dynamic Calc processor cannot lock more than [25] ESM blocks

Dear All,
I get the Following Error in the Essbase console when I try to Execute any CalcScript.
Error: 1012704 Dynamic Calc processor cannot lock more than [25] ESM blocks during the calculation, please increase CalcLockBlock setting and then retry(a small data cache setting could also cause this problem, please check the data cache size setting)_+
Please find the detailed output of the Statics of my Planning Applications Database and outline.
please help guys........
GetDbStats:
-------Statistics of AWRGPLAN:Plan1 -------
Dimension Name Type Declared Size Actual Size
===================================================================
HSP_Rates SPARSE 11 11
Account DENSE 602 420
Period DENSE 19 19
Year SPARSE 31 31
Scenario SPARSE 6 6
Version SPARSE 4 4
Currency SPARSE 10 10
Entity SPARSE 28 18
Departments SPARSE 165 119
ICP SPARSE 80 74
LoB SPARSE 396 344
Locations SPARSE 57 35
View SPARSE 5 5
Number of dimensions : 13
Declared Block Size : 11438
Actual Block Size : 7980
Declared Maximum Blocks : 3.41379650304E+015
Actual Maximum Blocks : 1.87262635317E+015
Number of Non Missing Leaf Blocks : 10664
Number of Non Missing Non Leaf Blocks : 2326
Number of Total Blocks : 12990
Index Type : B+ TREE
Average Block Density : 0.01503759
Average Sparse Density : 6.936782E-010
Block Compression Ratio : 0.001449493
Average Clustering Ratio : 0.3333527
Average Fragmentation Quotient : 19.3336
Free Space Recovery is Needed : No
Estimated Bytes of Recoverable Free Space : 0
GetDbInfo:
----- Database Information -----
Name : Plan1
Application Name : AWRGPLAN
Database Type : NORMAL
Status : Loaded
Elapsed Db Time : 00:00:05:00
Users Connected : 2
Blocks Locked : 0
Dimensions : 13
Data Status : Data has been modified
since last calculation.
Data File Cache Size Setting : 0
Current Data File Cache Size : 0
Data Cache Size Setting : 3128160
Current Data Cache Size : 3128160
Index Cache Size Setting : 1048576
Current Index Cache Size : 1048576
Index Page Size Setting : 8192
Current Index Page Size : 8192
Cache Memory Locking : Disabled
Database State : Read-write
Data Compression on Disk : Yes
Data Compression Type : BitMap Compression
Retrieval Buffer Size (in K) : 10
Retrieval Sort Buffer Size (in K) : 10
Isolation Level : Uncommitted Access
Pre Image Access : No
Time Out : Never
Number of blocks modified before internal commit : 3000
Number of rows to data load before internal commit : 0
Number of disk volume definitions : 0
Currency Info
Currency Country Dimension Member : Entity
Currency Time Dimension Member : Period
Currency Category Dimension Member : Account
Currency Type Dimension Member :
Currency Partition Member :
Request Info
Request Type : Data Load
User Name : admin@Native Directory
Start Time : Mon Aug 15 18:35:51 2011
End Time : Mon Aug 15 18:35:51 2011
Request Type : Customized Calculation
User Name : 6236@Native Directory
Start Time : Tue Aug 16 09:44:10 2011
End Time : Tue Aug 16 09:44:12 2011
Request Type : Outline Update
User Name : admin@Native Directory
Start Time : Tue Aug 16 10:50:02 2011
End Time : Tue Aug 16 10:50:02 2011
ListFiles:
File Type
Valid Choices: 1) Index 2) Data 3) Index|Data
>>Currently>> 3) Index|Data
Application Name: AWRGPLAN
Database Name: Plan1
----- Index File Information -----
Index File Count: 1
File 1:
File Name: C:\Oracle\Middleware\user_projects\epmsystem1\EssbaseServer\essbaseserver1\APP\AWRGPLAN\Plan1\ess00001.ind
File Type: INDEX
File Number: 1 of 1
File Size: 8,024 KB (8,216,576 bytes)
File Opened: Y
Index File Size Total: 8,024 KB (8,216,576 bytes)
----- Data File Information -----
Data File Count: 1
File 1:
File Name: C:\Oracle\Middleware\user_projects\epmsystem1\EssbaseServer\essbaseserver1\APP\AWRGPLAN\Plan1\ess00001.pag
File Type: DATA
File Number: 1 of 1
File Size: 1,397 KB (1,430,086 bytes)
File Opened: Y
Data File Size Total: 1,397 KB (1,430,086 bytes)
File Size Grand Total: 9,421 KB (9,646,662 bytes)
GetAppInfo:
-------Application Info-------
Name : AWRGPLAN
Server Name : GITSHYPT01:1423
App type : Non-unicode mode
Application Locale : English_UnitedStates.Latin1@Binary
Status : Loaded
Elapsed App Time : 00:00:05:24
Users Connected : 2
Data Storage Type : Multidimensional Data Storage
Number of DBs : 3
List of Databases
Database (0) : Plan1
Database (1) : Plan2
Database (2) : Plan3

ESM Block Issue
Cheers..!!

Anyone else have the issue where, after the 8,3 upgrade, you cannot access more than 1 exchange account on your iPhone? This is annoying to me as I need to access 4 daily and cannot due to this error.

Anyone else have the issue where, after the 8,3 upgrade, you cannot access more than 1 exchange account on your iPhone? This is annoying to me as I need to access 4 daily and cannot due to this error.
The first one, my private home email, works fine. With the other 3, I get the message "Cannot get mail: The connection to the server failed"
All were working fine before the 8.3 upgrade. I did try the old trick of making one minor change on the account and resaving, but that did not change anything. I even deleted my work account and re-entered it from scratch, but again, sadly, no luck. For the time being, I am successfully getting the email via IMAP, but this ***** compared to exchange. Anyone have any idea what is happening or if a fix is in the works?

Well, the one set up on exchange 2k3 is now working fine, although no changes were made on either the iPhone or the exchange side, so that's fun, but it still is throwing errors when connecting to the other 2 exchange accounts. The common elements are that both non-functioning exchange accounts are google apps for business accounts. So is one of the ones that's working, by the way. The settings on both accounts are the same as the one that's working, and both worked fine before the 8.3 upgrade. I have no issue accessing both of these accounts on my ipad which is currently on 8.2.x. If it's not the iphone OS at fault, I'm at a loss as to what it could be.

Cisco AP 1252AG Cannot setup More than 54Mb/s speed in radio 0 (2.4G)

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:SimSun;
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
I have a problem when I configure CISCO AP 1252, it cannot support more than 54Mb/s speed but support 802.n which speed can up to 300Mb/s. See below :
here is dot11radio 0 speed option: (The MAX speed is 54Mb/s by manually, how can i setup more than 54Mb/s, because of this AP support 802.n. So the speed should be more than 54M/s, like 300M)
AP#sho inter dot11Radio 0
Dot11Radio0 is up, line protocol is up
   Hardware is 802.11N 2.4Ghz Radio, address is *************
   MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
AP(config)#inter dot11Radio 0
AP(config-if)#speed ?
   1.0         Allow 1.0 Mb/s rate
   11.0        Allow 11.0 Mb/s rate
   12.0        Allow 12.0 Mb/s rate
   18.0        Allow 18.0 Mb/s rate
   2.0         Allow 2.0 Mb/s rate
   24.0        Allow 24.0 Mb/s rate
   36.0        Allow 36.0 Mb/s rate
   48.0        Allow 48.0 Mb/s rate
   5.5         Allow 5.5 Mb/s rate
   54.0        Allow 54.0 Mb/s rate
***(why here without more than 54M/s rate, CISCO AP 1252 support IEEE802/n)
   6.0         Allow 6.0 Mb/s rate
   9.0         Allow 9.0 Mb/s rate
   basic-1.0   Require 1.0 Mb/s rate
   basic-11.0 Require 11.0 Mb/s rate
   basic-12.0 Require 12.0 Mb/s rate
   basic-18.0 Require 18.0 Mb/s rate
   basic-2.0   Require 2.0 Mb/s rate
   basic-24.0 Require 24.0 Mb/s rate
   basic-36.0 Require 36.0 Mb/s rate
   basic-48.0 Require 48.0 Mb/s rate
   basic-5.5   Require 5.5 Mb/s rate
   basic-54.0 Require 54.0 Mb/s rate
***(why here without over than 54Mb/s Rate?, it support IEEE802.n)
   basic-6.0   Require 6.0 Mb/s rate
   basic-9.0   Require 9.0 Mb/s rate
   default     Set default rates
   m0-7        Allow MCS rate indices 0-7
   m0.         Allow MCS rate index 0
   m1.         Allow MCS rate index 1
   m10.        Allow MCS rate index 10
   m11.        Allow MCS rate index 11
   m12.        Allow MCS rate index 12
   m13.        Allow MCS rate index 13
   m14.        Allow MCS rate index 14
   m15.        Allow MCS rate index 15
   m2.         Allow MCS rate index 2
   m3.         Allow MCS rate index 3
   m4.         Allow MCS rate index 4
   m5.         Allow MCS rate index 5
   m6.         Allow MCS rate index 6
   m7.         Allow MCS rate index 7
   m8-15       Allow MCS rate indices 8-15
   m8.         Allow MCS rate index 8
   m9.         Allow MCS rate index 9
   ofdm        How to place OFDM rates in rates elements
   only-ofdm   Set rates for best OFDM throughput (no ERP protection will be used)
   range       Set rates for best range
   throughput Set rates for best throughput (includes non-OFDM rates and may cause ERP
Why this device cannot support 300Mb/s rate in radio 0 of speed ?
i want to setup more than 54 Mb/s when i use my laptop to connect this AP.

The 802.11n HT rates apply only to no encryption or WPA2/AES encryption. They do not apply to WEP or WPA encryption. If WEP or TKIP encryption is used, the 1250 series access points and any 802.11n Draft 2.0 clients will not transmit at the HT rates. Legacy rates (802.11a/b/g) will be used for any clients using WEP or TKIP encryption.
Ref.: Release Notes
40MHz Operation
If the throughput you get from a 20-MHz channel isn't enough for your speedy users, you can flip each 5-GHz 11n radio into a bonded-channel configuration.
You can configure 40-MHz operation on the 2.4-GHz radio of the 1250 Series AP, but this isn't recommended or supported. The primary reason against it is that with a wide channel in a band that has so little available spectrum (and so much interference), you make a single AP capable of higher throughput at the expense of performance for all neighboring access points-certainly not the way enterprise WLANs ought to be designed. Also, the vast majority of client chipsets (Intel's, for one) will not support 40-MHz operation in the 2.4-GHz space.
Ref.: Cisco 802.11n Design and Deployment Guidelines
Making the Most of Things
Once you're connected at 802.11n HT rates, you'll want to make sure you don't lose the throughput gains you should be able to achieve. Not all may be within your control, but if you understand the performance implications of these variables, it will help you in baselining your WLAN capabilities.
When your laptops are unplugged, the 11n client will likely try aggressively to save battery power. Depending on client radio and chipset, it's not uncommon to see performance drop by as much as 50 percent. Unless you know how to fully disable this, keep your laptops plugged in if you want maximum performance,
Note: Even if you managed to disable this power save function, most laptop motherboards/chipsets have automated power-saving features that kick in when the laptop is unplugged. At best, these are difficult to disable. Thus, it is strongly recommended that you not do performance testing when clients are battery operated.
As detailed previously, throughput performance may vary as legacy devices are introduced into the 802.11n environment. This is to be expected, but make sure that you find a channel void of all legacy transmissions if you want to test the high-water mark of your new 11n WLAN. If that isn't possible, adjust your expectations accordingly.
Ref.: Cisco 802.11n Design and Deployment Guidelines
Regards,
André

I cannot open more than 1 Tab per window. The "+" does not work as well as the item "New Tab" from the File drop-down menu. What shall I do ?

I have just removed FireFox and reinstalled it again on my Mac Book PRO.
When I open FIreFox I canNOT open more than 1 TAB.
I click on the "+"on the top line of the window. It should open another TAB but id does NOT.
I click on the File item in the top menu bar. A drop-down menu pops up. I click on "New Tab" and nothing happens.
How can I get more than 1 Tab on the same window ?
This feature works with Safari !
Thank you so much.
Best regards

We have seen reports about a Community Toolbar extension causing this issue with not being able to open a new tab.
So if you have such a toolbar then start with disabling it.
*Tools > Add-ons > Extensions
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

Cannot connect more than 1 mac to internet?

Similar Messages

Maybe you are looking for