Cannot connect to com1 in PXI2530 using Switch Executive
I have a PXI2530 configured using Switch Executive 2.10. The first 60 Channels are setup with my signal names on ch0 - ch59. Com0, 1, 2 and 3 are my Instrument connections. The IVI Driver Sessions has Driver Setup set to Topology:2530/1-Wire Octal 16x1 Mux.
When I try to configure either a Channel, Route or a Group, there is only a com0 pin and no com1, 2, 3, 4, 5, 6 or 7. There is no way to connect to any pin beyond ch15.
The configuration looks like it is setup for a 128:1 mux, but when I try to connect ch16 to com0, it cannot complete the route. Ch16 cannot be connected to com0 or any channel in the list. Any idea what I am doing wrong?
Michael Munroe, ABCDEF
Certified LabVIEW Developer, MCP
Find and fix bad VI Properties with Property Inspector
http://forums.ni.com/ni/board/message?board.id=320&message.id=633
Duplicate threadMessage Edited by Berto on 02-28-2006 12:15 PM
Similar Messages
-
Cannot connect to com1 using Switch Executive
I have a PXI2530 configured using Switch Executive 2.10. The first 60 Channels are setup with my signal names on ch0 - ch59. Com0, 1, 2 and 3 are my Instrument connections. The IVI Driver Sessions has Driver Setup set to Topology:2530/1-Wire Octal 16x1 Mux.
When I try to configure either a Channel, Route or a Group, there is only a com0 pin and no com1, 2, 3, 4, 5, 6 or 7. There is no way to connect to any pin beyond ch15.
The configuration looks like it is setup for a 128:1 mux, but when I try to connect ch16 to com0, it cannot complete the route. Ch16 cannot be connected to com0 or any channel in the list. Any idea what I am doing wrong?
Michael Munroe, ABCDEF
Certified LabVIEW Developer, MCP
Find and fix bad VI Properties with Property InspectorMichael,
What probably happened is that originally the NISE vd was created using the 128x1 topology. If the driver session is changed to another topology (like Octal 16x1 Mux) and saved the linked from the NISE vd and the old topology still exists until you close MAX and reopen it. When MAx opens it establishes a link between the NISE vd and driver session which remains in memory until MAX is closed and reopened.
Guy Ferraro
Switch Product Support Engineer
NI - USA -
How to restart base station from airport utility? I used to be able to do it remotely
I currently use a Mac Pro 10.8.4 and have a time machine for wireless 6.3 (630.34). Sometimes I cannot connect to the internet and use network preferences to diagnose the issue. This results in being told to restart the wireless. The airport utility includes the drop down option of restarting but is not clickable so I can't choose it.
With my prior macbook and same time capsule, etc if i had problems connecting to the internet I would run network diagnostics to help out. This included clicking on the airport utility ---> base station --> restart. This worked most of the time.
Bottom line, is there something I am missing in not being able to restart the wi-fi remotely? ]
Thanks in advanceYou are likely forgetting a step.
Open AirPort Utility
Click on the Time Capsule icon
Click Edit in the small window that appears
Now click the Base Station menu.....top of the screen....not the Base Station "tab" in the center of the screen
Click Restart -
Scan list using Switch Executive
I have a number of signal routes using multiple switch cards that I have set up using switch executive. I want to create a scan list that will switch each of my routes in turn each time I see a hardware trigger on the trigger inputs of my switches.
I have looked at some examples in TestStand and can see that if I use the IVI Switch Step using the IVI Switching setting that I can set up a scan list but that seems to be only for one switch card, I have two that I need to route signals to a Digitizer. I can not see a way of using my routes set up using Switch Executive.
I can either use LabView2013 or TestStand 2013 to do this.
Some help would be most appreciated?
WayneHi Wayne,
If I have understood your problem correctly, this VI in LabVIEW sound like it does what you are after.
NI Switch Route Trigger Input
Also at the bottom of this LINK are some examples of scan lists, perhaps you will be able to adapt this to your needs
Please let me know how you get on
Kevin R
Applications Engineer
National Instruments UK&Ireland -
I cannot connect to the I tunes store after recently downloading I tunes 11.1 I just get the error code 0x80092013 so not sure what to do. I have tried deleting and then reinstalling I tunes with no luck. I tried to flush my DNS but that did not work, I tried the diagnostics in I tunes and it told me my connections were fine but said the "secure link to I tunes store failed" Looking for an answer thanks!
Okay I was able to connect back to the I tunes store in I tunes 11.1 taking care of the error 0x80092013. I did this in XP going to the firewall controls, selecting the exception tab. I tunes was already in the exceptions tab but I deleted it anyway, then I added I tunes back using the Add Program button then browsing to the I tunes.exe location in the C drive then selected that as the program. I tunes showed back up in the exceptions once again. I then shut down the computer and restarted it and I then had a connection with I tunes. So the I tunes in the exceptions tab in the firewall was not working I just replaced it with a fresh one.
-
How do I associate switches in a four layer relay tree using Switch Executive
I have a three layer relay tree, controlled with a PXI-2567, to route an instrument input to 16 DUT channels. How do I create aliases in Switch Executive to turn the appropriate set of three relays on and off to route the input signal to one of the channels?
Bob,
Here is what you need to do to be able to call 2 end channels and create a route though 3 layers.
1) You have to tell NISE how the independent relays are connected to each other. You will do that by creating Hardwires.
2) You need to tell NISE that you want the channels connected to the hardwires to be used for routing. You will do that by marking the connected channels as "Reserved for Routing".
3) You can name the end channels according to your topology. COM for the single input channel and CH0 to CH15 for the output channels by creating aliases.
In the route editor, you will only need to create a route between COM and CHx and NISE will find the appropriate relays to close. In the route editor, if you only want to see the channels with an alias (COM, CH0, CH1 etc...) select in Options "Hide channels without aliases" -
Cannot connect to a named instance using SSMS from a remote machine
Hi all,
SQL Server.....: 2012 EE
OS...................: Windows Server 2008 R2
I have a desktop machine, that i am using to administrer SQL Server (via SSMS) and to develop my SSIS solutions, but i can't connect to a named instance of my SQL Server. When i try to connect using SSMS to my named instance (myhost\DWSERVER)
i get a huge error message:
A network-related or instance-specific error occurred while establisinh a connection to SQL Server. The server was not found or was not accessible. Verify that the instance is correct and that SQL Server is configured to allow remote connections.
(provider: TCP Provider, error: 0 - A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.) (Microsoft SQL Server, Error: 10060)
Locally, i am able to access that named instance using SSMS, just when i try to access from another machine, the above error pops-up to me.
I am using the SQL Server Authentication mode to connect to the named instance.
What am i doing wrong?
Thanks in advance.
Fabrício Pedroso Jorge Database Administrator - Belém, Pará, BrazilHi,
thanks for your attention.
That's correct, i can connect to my default instance both locally and remotelly. The default instance in on port 1433. I cannot find the port used by the named instance (DWSERVER).
Actually, i found this on the errorlog from the named instance:
2015-03-22 10:10:45.80 spid13s Server is listening on [ 'any' <ipv6> 49411].
2015-03-22 10:10:45.80 spid20s Server is listening on [ 'any' <ipv6> 5023].
2015-03-22 10:10:45.81 spid20s Server is listening on [ 'any' <ipv4> 5023].
2015-03-22 10:10:45.81 spid20s The Database Mirroring endpoint is now listening for connections.
2015-03-22 10:10:46.12 spid13s Server is listening on [ 'any' <ipv4> 49411].
2015-03-22 10:10:46.25 spid13s Server local connection provider is ready to accept connection on [ \\.\pipe\SQLLocal\DWSERVER ].
2015-03-22 10:10:46.26 spid13s Server local connection provider is ready to accept connection on [ \\.\pipe\MSSQL$DWSERVER\sql\query ].
2015-03-22 10:10:46.26 Server Server is listening on [ ::1 <ipv6> 49412].
2015-03-22 10:10:46.26 Server Server is listening on [ 127.0.0.1 <ipv4> 49412].
I can ping normally to the remote server.
Fabrício Pedroso Jorge Database Administrator - Belém, Pará, Brazil -
Cannot connect with SQL Server driver using Top Link with ADF/JSF
I have a TopLink/ADF/JSF project that I'm starting using JDeveloper 10.1.3. The database is MS SQL Server. I went through and created all of the Top Link mappings, etc. but when I try to run my project under the OC4J instance built in to JDeveloper I get the error message below. I've tried putting SelectMethod=cursor everywhere I can think of, but nothing seems to help?
Log Dump:
[TopLink Info]: 2006.06.16 02:49:46.253--ServerSession(1679)--Thread(Thread[ApplicationServerThread-0,5,RequestThreadGroup])--TopLink, version: Oracle TopLink - 10g Release 3 (10.1.3.0.0) (Build 060118)
[TopLink Config]: 2006.06.16 02:49:46.269--ServerSession(1679)--Connection(1680)--Thread(Thread[ApplicationServerThread-0,5,RequestThreadGroup])--connecting(DatabaseLogin(
platform=>SQLServerPlatform
user name=> "zeke"
connector=>JNDIConnector datasource name=>jdbc/ZekeDB
[TopLink Severe]: 2006.06.16 02:49:48.925--ServerSession(1679)--Thread(Thread[ApplicationServerThread-0,5,RequestThreadGroup])--Local Exception Stack:
Exception [TOPLINK-4002] (Oracle TopLink - 10g Release 3 (10.1.3.0.0) (Build 060118)): oracle.toplink.exceptions.DatabaseException
Internal Exception: java.sql.SQLException: [Microsoft][SQLServer 2000 Driver for JDBC]JTA is not support when selectMethod=direct. Switch to selectMethod=cursor.Error Code: 0
at oracle.toplink.exceptions.TopLinkException.<init>(TopLinkException.java:46)
at oracle.toplink.exceptions.DatabaseException.<init>(DatabaseException.java:51)
at oracle.toplink.exceptions.DatabaseException.sqlException(DatabaseException.java:276)
at oracle.toplink.jndi.JNDIConnector.connect(JNDIConnector.java:115)
at oracle.toplink.sessions.DatasourceLogin.connectToDatasource(DatasourceLogin.java:147)
at oracle.toplink.internal.databaseaccess.DatasourceAccessor.connect(DatasourceAccessor.java:197)
at oracle.toplink.internal.databaseaccess.DatabaseAccessor.connect(DatabaseAccessor.java:221)
at oracle.toplink.internal.databaseaccess.DatasourceAccessor.connect(DatasourceAccessor.java:273)
at oracle.toplink.threetier.ConnectionPool.buildConnection(ConnectionPool.java:81)
at oracle.toplink.threetier.ConnectionPool.startUp(ConnectionPool.java:304)
at oracle.toplink.threetier.ServerSession.connect(ServerSession.java:431)
at oracle.toplink.publicinterface.DatabaseSession.login(DatabaseSession.java:511)
at oracle.toplink.tools.sessionmanagement.SessionManager.getSession(SessionManager.java:317)
at oracle.toplink.tools.sessionmanagement.SessionManager.getSession(SessionManager.java:372)
at oracle.toplink.util.SessionFactory.getSharedSession(SessionFactory.java:103)
at oracle.toplink.util.SessionFactory.getSharedSession(SessionFactory.java:82)
at oracle.toplink.util.SessionFactory.acquireSession(SessionFactory.java:114)
at com.mascocs.web.monitor.admin.datamodel.ZekeAdminSessionFacadeBean.findAllApps(ZekeAdminSessionFacadeBean.java:128)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:585)
at com.evermind.server.ejb.interceptor.joinpoint.EJBJoinPointImpl.invoke(EJBJoinPointImpl.java:35)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:69)
at com.evermind.server.ejb.interceptor.system.DMSInterceptor.invoke(DMSInterceptor.java:52)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:69)
at com.evermind.server.ejb.interceptor.system.TxRequiredInterceptor.invoke(TxRequiredInterceptor.java:55)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:69)
at com.evermind.server.ejb.interceptor.system.DMSInterceptor.invoke(DMSInterceptor.java:52)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:69)
at com.evermind.server.ejb.StatelessSessionEJBObject.OC4J_invokeMethod(StatelessSessionEJBObject.java:86)
at ZekeAdminSessionFacadeLocal_StatelessSessionBeanWrapper0.findAllApps(ZekeAdminSessionFacadeLocal_StatelessSessionBeanWrapper0.java:165)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:585)
at oracle.adf.model.binding.DCInvokeMethod.invokeMethod(DCInvokeMethod.java:504)
at oracle.adf.model.binding.DCDataControl.invokeMethod(DCDataControl.java:1796)
at oracle.adf.model.generic.DCGenericDataControl.invokeMethod(DCGenericDataControl.java:248)
at oracle.adf.model.binding.DCInvokeMethod.callMethod(DCInvokeMethod.java:216)
at oracle.jbo.uicli.binding.JUCtrlActionBinding.doIt(JUCtrlActionBinding.java:1287)
at oracle.adf.model.binding.DCDataControl.invokeOperation(DCDataControl.java:1802)
at oracle.adf.model.generic.DCGenericDataControl.invokeOperation(DCGenericDataControl.java:266)
at oracle.adf.model.adapter.AdapterDCService.invokeOperation(AdapterDCService.java:318)
at oracle.jbo.uicli.binding.JUCtrlActionBinding.invoke(JUCtrlActionBinding.java:625)
at oracle.jbo.uicli.binding.JUMethodIteratorDef$JUMethodIteratorBinding.invokeMethodAction(JUMethodIteratorDef.java:160)
at oracle.jbo.uicli.binding.JUMethodIteratorDef$JUMethodIteratorBinding.initSourceRSI(JUMethodIteratorDef.java:542)
at oracle.adf.model.binding.DCIteratorBinding.callInitSourceRSI(DCIteratorBinding.java:1420)
at oracle.adf.model.binding.DCIteratorBinding.getRowSetIterator(DCIteratorBinding.java:1403)
at oracle.adf.model.binding.DCIteratorBinding.setRangeSize(DCIteratorBinding.java:2641)
at oracle.adf.model.binding.DCBindingContainer.internalRefreshControl(DCBindingContainer.java:2484)
at oracle.adf.model.binding.DCBindingContainer.refresh(DCBindingContainer.java:2257)
at oracle.adf.controller.v2.lifecycle.PageLifecycleImpl.prepareModel(PageLifecycleImpl.java:104)
at oracle.adf.controller.v2.lifecycle.Lifecycle$8.execute(Lifecycle.java:210)
at oracle.adf.controller.v2.lifecycle.Lifecycle.executePhase(Lifecycle.java:116)
at oracle.adf.controller.faces.lifecycle.ADFPhaseListener.mav$executePhase(ADFPhaseListener.java)
at oracle.adf.controller.faces.lifecycle.ADFPhaseListener$4.after(ADFPhaseListener.java:331)
at oracle.adf.controller.faces.lifecycle.ADFPhaseListener.afterPhase(ADFPhaseListener.java:97)
at com.sun.faces.lifecycle.LifecycleImpl.phase(LifecycleImpl.java:211)
at com.sun.faces.lifecycle.LifecycleImpl.execute(LifecycleImpl.java:90)
at javax.faces.webapp.FacesServlet.service(FacesServlet.java:197)
at com.evermind.server.http.ResourceFilterChain.doFilter(ResourceFilterChain.java:64)
at oracle.adfinternal.view.faces.webapp.AdfFacesFilterImpl._invokeDoFilter(AdfFacesFilterImpl.java:367)
at oracle.adfinternal.view.faces.webapp.AdfFacesFilterImpl._doFilterImpl(AdfFacesFilterImpl.java:336)
at oracle.adfinternal.view.faces.webapp.AdfFacesFilterImpl.doFilter(AdfFacesFilterImpl.java:196)
at oracle.adf.view.faces.webapp.AdfFacesFilter.doFilter(AdfFacesFilter.java:87)
at com.evermind.server.http.EvermindFilterChain.doFilter(EvermindFilterChain.java:15)
at oracle.adf.model.servlet.ADFBindingFilter.doFilter(ADFBindingFilter.java:332)
at com.evermind.server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:627)
at com.evermind.server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:376)
at com.evermind.server.http.HttpRequestHandler.doProcessRequest(HttpRequestHandler.java:870)
at com.evermind.server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:451)
at com.evermind.server.http.HttpRequestHandler.serveOneRequest(HttpRequestHandler.java:218)
at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:119)
at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:112)
at oracle.oc4j.network.ServerSocketReadHandler$SafeRunnable.run(ServerSocketReadHandler.java:260)
at oracle.oc4j.network.ServerSocketAcceptHandler.procClientSocket(ServerSocketAcceptHandler.java:230)
at oracle.oc4j.network.ServerSocketAcceptHandler.access$800(ServerSocketAcceptHandler.java:33)
at oracle.oc4j.network.ServerSocketAcceptHandler$AcceptHandlerHorse.run(ServerSocketAcceptHandler.java:831)
at com.evermind.util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:298)
at java.lang.Thread.run(Thread.java:595)
Caused by: java.sql.SQLException: [Microsoft][SQLServer 2000 Driver for JDBC]JTA is not support when selectMethod=direct. Switch to selectMethod=cursor.
at com.microsoft.jdbc.base.BaseExceptions.createException(Unknown Source)
at com.microsoft.jdbc.base.BaseExceptions.getException(Unknown Source)
at com.microsoft.jdbcx.sqlserver.SQLServerDataSource.getXAConnection(Unknown Source)
at oracle.oc4j.sql.spi.ManagedConnectionFactoryImpl.createXAConnection(ManagedConnectionFactoryImpl.java:237)
at oracle.oc4j.sql.spi.ManagedConnectionFactoryImpl.createManagedConnection(ManagedConnectionFactoryImpl.java:199)
at com.evermind.server.connector.ApplicationConnectionManager.createManagedConnection(ApplicationConnectionManager.java:1333)
at oracle.j2ee.connector.ConnectionPoolImpl.createManagedConnectionFromFactory(ConnectionPoolImpl.java:324)
at oracle.j2ee.connector.ConnectionPoolImpl.access$800(ConnectionPoolImpl.java:95)
at oracle.j2ee.connector.ConnectionPoolImpl$FixedWaitPoolingScheme.getManagedConnection(ConnectionPoolImpl.java:1449)
at oracle.j2ee.connector.ConnectionPoolImpl.getManagedConnection(ConnectionPoolImpl.java:782)
at com.evermind.server.connector.ApplicationConnectionManager.getConnectionFromPool(ApplicationConnectionManager.java:1532)
at com.evermind.server.connector.ApplicationConnectionManager.acquireConnectionContext(ApplicationConnectionManager.java:1477)
at com.evermind.server.connector.ApplicationConnectionManager.allocateConnection(ApplicationConnectionManager.java:1423)
at oracle.j2ee.connector.OracleConnectionManager.unprivileged_allocateConnection(OracleConnectionManager.java:244)
at oracle.j2ee.connector.OracleConnectionManager.allocateConnection(OracleConnectionManager.java:198)
at oracle.oc4j.sql.ManagedDataSource.getConnection(ManagedDataSource.java:197)
at oracle.oc4j.sql.ManagedDataSource.getConnection(ManagedDataSource.java:140)
at oracle.toplink.jndi.JNDIConnector.connect(JNDIConnector.java:112)
... 77 more
2006-06-16 14:49:48.941 ERROR J2EE EJB8006 [ZekeAdminSessionFacade:public java.util.List com.mascocs.web.monitor.admin.datamodel.ZekeAdminSessionFacadeBean.findAllApps()] exception occurred during method invocation: javax.ejb.EJBException: Exception [TOPLINK-4002] (Oracle TopLink - 10g Release 3 (10.1.3.0.0) (Build 060118)): oracle.toplink.exceptions.DatabaseException
Internal Exception: java.sql.SQLException: [Microsoft][SQLServer 2000 Driver for JDBC]JTA is not support when selectMethod=direct. Switch to selectMethod=cursor.Error Code: 0; nested exception is: Exception [TOPLINK-4002] (Oracle TopLink - 10g Release 3 (10.1.3.0.0) (Build 060118)): oracle.toplink.exceptions.DatabaseException
Internal Exception: java.sql.SQLException: [Microsoft][SQLServer 2000 Driver for JDBC]JTA is not support when selectMethod=direct. Switch to selectMethod=cursor.Error Code: 0
2006-06-16 14:49:50.816 WARNING rowIterator is null
2006-06-16 14:49:50.831 WARNING rowIterator is null
Process exited.I'm not sure on the error, but you may be able to pass the "selectMethod" and "cursor" as a JDBC property in your connection pool. Since this is a DataSource / JTA issue you may want to post it to the general OC4J forum.
Otherwise as a workaround you could instead use a non-JTA DataSouce, or use TopLink internal connection pooling, or try another JDBC driver. -
Cannot connect to itunes store? Use VPN
Im using a VPN on my iDevice to get over this issue temporarily (german IP) and its accessing the app store just fine.
Hope this helps!Hi,
No, cannot access itunes store even when the ipad is not connected.
Laptop is a lenovo Thinkpad SL400 and router is Netgear ADSL modem router. I also tried it with Ethernet connection but the result is the same.
Cheers -
Ok, so after purchasing a new computer, with windows 7 pro, 64 bit, I tried downloading the newest iTunes, which at the time was 10.2.1 (i believe). After installation, everything seemed to work, except that iTunes was unable to securely connect to the internet, use home sharing, or validate my computer.
As troubleshooting, I first ran msconfig, and then turned OFF all programs that boot at start up EXCEPT itunes and quicktime. After a restart, i opened itunes again, and got the same result. That led me to believe that iTunes was NOT being blocked by another program on my machine. I am currently running itunes 10.7 successfully on a Windows 7 32 machine at work. Anyhow, for grins, I tried to install version 9 on the new computer, and it installed perfectly, and immediately connected to the itunes store, leading me to believe that there is nothing wrong with my software configuration (not sure if this is a safe assumption or not). I then tried to let iTunes update itself using the automated update function. It tried to update itself to the most current version, then 10.6. Again, iTunes was unable to connect to the iTunes store. I HAVE tried disabling the anti-virus software (AVG), but that made no difference.
I have since gone back and reinstalled iTunes 9. Here's the catch though. When I reinstalled using version 9, I had to redo all my library files. I'm about 1/2 way through my CD's, and now have a substantial library file going. The last time I let iTunes update itself to 10.6, once I realized that it was not going to connect to the store, I uninstalled iTunes, and reinstalled ver. 9. However, when I did this, it told me it could no longer open the library file, because it was a newer .itl or .xml (i believe it was one of those two extensions) library file. At that point, I basically started everything over again, using version 9, and have been importing CD's like a madman at night.
Here are my questions:
1) Is there a way to make a copy of the files that store my library info, so that if my upgrade to ver 10 IS NOT SUCCESSFUL, I can restore ver 9, but still have all of the album art work, playlists (when I import music, I create a playlist with the artists' name, and store things that way), etc. in tact?
2) What else can I try (firewall settings, internet options, etc.) to try and get version to to successfully install? I would really like to get all the benfits of the newer versions.
3) When I tried to get apple tech support before, they wanted me to pay a ridiculous 69$ fee for phone support. I just bought an iphone 5....this should entitle me to a fresh 90 days of phone support, right? The reason I ask here is that I could hardly understand the "tech" that answered the phone when I called for tech support last time, and to be honest, it really ****** me off that they wanted to try and milk me for another 69 bucks....I've purchased every iPhone since the 3Gs came out (pre-ordered at that), and have nearly gone broke purchasing music from their iTunes store....heck, maybe they're doing me me a favor not letting me into the store, huh?
Any help or ideas would be greatly appreciated,
-BrianMany thanks.
With those symptoms, I'd try the following document:
Apple software on Windows: May see performance issues and blank iTunes Store
(If there's a SpeedBit LSP showing up in Autoruns, it's usually best to just uninstall your SpeedBit Video Accelerator.) -
Cannot connect to wpa protected wifi using netcfg
This is the setting in networkmanager's nm-applet and it connects flawlessly. http://i.imgur.com/5VuL6.png
I tried doing the same configuration in netcfg and this is my config file.
CONNECTION='wireless'
INTERFACE=wlan0
SECURITY='wpa-configsection'
ESSID="my essid"
IP='dhcp'
CONFIGSECTION='
ssid="essid"
key_mgmt=WPA-EAP
eap=PEAP
group=CCMP
pairwise=CCMP
identity="foobar"
password="pass"
priority=1
phase2="auth=MSCHAPV2"
I killed wpa_supplient & started it with option to log to a file by
wpa_supplicant -u -f /var/log/wpa.log -B
Now, just to check whether wpa_supplient is still working perfectly, I restarted networkmanager and checked whether I was able to connect to the wifi & I was able to do it.
I stopped the networkmanager & ran "netcfg up mywifi" & I got nothing in the logfile of wpa_supplient & got a simple message saying "WPA Authentication/Association Failed"..
If I switch on debugging, I get
[root@archlinux shadyabhi]# NETCFG_DEBUG="yes" netcfg up dwifi
DEBUG: Loading profile dwifi
DEBUG: Configuring interface wlan0
:: dwifi up [BUSY] DEBUG: status reported to profile_up as:
DEBUG: Loading profile dwifi
DEBUG: Configuring interface wlan0
DEBUG: wireless_up start_wpa wlan0 /run/network/wpa.wlan0/wpa.conf nl80211,wext
DEBUG: wireless_up Configuration generated at /run/network/wpa.wlan0/wpa.conf
DEBUG: wireless_up wpa_reconfigure wlan0
DEBUG: wpa_cli -i wlan0 -p /run/wpa_supplicant reconfigure
DEBUG: wireless_up ifup
DEBUG: wireless_up wpa_check
DEBUG: wpa_cli -i wlan0 -p /run/wpa_supplicant status
DEBUG: wpa_cli -i wlan0 -p /run/wpa_supplicant status
DEBUG: wpa_cli -i wlan0 -p /run/wpa_supplicant status
DEBUG: wpa_cli -i wlan0 -p /run/wpa_supplicant status
DEBUG: wpa_cli -i wlan0 -p /run/wpa_supplicant status
DEBUG: wpa_cli -i wlan0 -p /run/wpa_supplicant status
DEBUG: wpa_cli -i wlan0 -p /run/wpa_supplicant status
DEBUG: wpa_cli -i wlan0 -p /run/wpa_supplicant terminate
> WPA Authentication/Association Failed
DEBUG: profile_up connect failed
What's up here?Probably too late to respond on this, but I had the same pattern in my debug output. This is how I solved it:
https://bbs.archlinux.org/viewtopic.php … 4#p1150234 -
Hp pavilion d4790y windows vista cannot connect to internet wirelessly unless using WEP
I have a HP Pavilion d4790y with Windows Vista 32 bit home premium. I can connect to my ISP router wirelessly using the HP internal network adapter, but the connection from the router to the internet does not work unless I downgrade the router security to WEP. If I connect to the router with a wired connection, I can connect to the internet no problem even with WPA2. I have done all the recomended troubleshooting steps like resetting the router, checking for network adapter driver update, uninstall/reinstall network adapter driver, release and renew the ip config, etc. Suggesions? Is there a more recent driver that is not being recognized during the update search process?
This question was solved.
View Solution.Hi,
This is a hardware thing and the wireless card does not support this. Changing the wireless card may be the way to go.
Hope this helps.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. -
Cannot connect to Oracle express database using Oracle forms 10 on win XP
Hello All,
I have installed Oracle Developer Suite 10g along with Oracle Express edition database on Windows XP home edition. (Do get successful installation message)
When i open up Forms builder and try to use connect option- it comes up with user name, password and database dialogue box?
If I enter user name and password I choose while installation express edition database it comes up with the following error:
"ORA-12560:TNS:protocol adapter error"
Have checked the services and they all seem to be running, have tried deinstalling/installing by removing registry values but still no luck.
In fact what ever I type the error message remains the same.
On the other hand I can access Express edition database using user name and password I choose during its installation.
Can any one please reply me what details i need to enter here? Is it same as I set up during express edition database installation? What about database?
Please help. As I am struggling big time.
Thanks in advance.You may be having the same problem as this guy:
Forms 6i - ora-012203 tns:unable to connect to the destination
You need to start SQL Plus and see if you can log in, too, to make sure there are not other problems.
What are you using for the Database name (the third entry following username and password)? -
Hi, I'm trying to connect to "AdminAPI" site, using Windows Authentication using REST API, but i always get the following error.
user is not authorized to access the management service
I also wrote a powershell script that gets the token from windows auth site, and connects to AdminAPi site, it works fine natively, when i run in ISE, but when i execute the same PS script using C# in my custom resource provider, it gives the same above
error.
How should i go about it? please help?
string EnvironmentToUse = "https://localhost";
string domainName = "//";
string userName = "***";
string password = "***@123";
string adminApiEndpoint = "https://localhost:30004";
ServicePointManager.ServerCertificateValidationCallback += new RemoteCertificateValidationCallback(delegate { return true; });
string windowsAuthSiteEndPoint = EnvironmentToUse + ":30072";
string token = TokenIssuer.GetWindowsAuthToken(windowsAuthSiteEndPoint, domainName, userName, password, true);
var myAdminClient = new AdminManagementClient(new Uri(adminApiEndpoint), token);
var u = await myAdminClient.ListUsersAsync(new Query { });
PS Script:
$AdminURI = "https://localhost:30004";
$AuthSite = "https://localhost:30072/";
$ClientRealm = "https://localhost:30091/";
$Credential = Get-Credential
$Token = Get-MgmtSvcToken -Type Windows –AuthenticationSite "https://localhost:30072/" -ClientRealm "http://azureservices/AdminSite" -User $Credential -DisableCertificateValidation
$Token
$users = Get-MgmtSvcUser -AdminUri "https://localhost:30004/" -Token $Token -DisableCertificateValidation;The user context you are executing the script/cmdlets needs to be added as an administrator into WAP, or else you won't be authorized.
To add a new user to WAP Admin, see the following PS example:
Add-MgmtSvcAdminUser -Principal <string> -Server <string>
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com ) -
When I try to connect Oracle 7.2.2 database using JDBC thin driver of Java 1.1.8 in JDeveloper, the connection manager refuse to connect the database and alert the minimum version supported is 7.2.3. But I know JDBC thin driver can connect database of 7.2.x onwards. Any way to workaround? Thank you.
Hi Tian-liang,
Try using Microsofts JDBC driver rather than Suns. Also search these forums, other have run into the same issue.
Thank you
Don
Maybe you are looking for
-
I am building a Window 7 Ent master image containing 200+ engineering applications which will be deployed to 800+ systems. My problem is, I'm close to running out of activations and am now down to one rearm remaining. I have the option of using our K
-
Mighty Mouse no longer working properly
The Mighty Mouse has been irritating me quite a bit because the scrollbar frequently stops working. Usually, the cleaning method provides a temporary solution (very temporary considering I've lost count of the number of times this has happened) but n
-
Spry accordion and #wrapper issue
Hi I am in the process of trying to put together a portfolio site as part of a CIW course. If you look at the current site www.jmacphot.com you will see on the equipment page I have tried to add a spry accordion and then a spry tabbed menu inside the
-
Free Mountain Lion update?
While purchasing our new iMac I was told I could also update my MacBook Pro (bought Dec.2011) to Mountain Lion @ no charge. I can not find a link for this.....
-
I have written form statment in subroutine program and calling in script layout using perform statment it is not calling in the script. i written following code in the subroutine program . PROGRAM ZWHDTAX. form WHDTAX tables in_tab structure i