Cannot connect to second SSID on Aironet 1231
Hi,
I have configure my AP with to SSID (11 & 12), but I cannot connect to 12. It authenticates, and while trying to acquire IP address from 12, it fails and connects me to 11 (if I have already saved the SSID connection).
The following is my AP status:
Product/Model Number:
AIR-AP1231G-A-K9
System Software Filename:
c1200-k9w7-tar.123-8.JEE
System Software Version:
12.3(8)JEE
Bootloader Version:
12.3(2)JA4
The SSID 12 already have 4 clients connected, And I am tring to connect a 5th one (smart phone), but cannot connect to 12, instead coneected to 11. Also tried with a laptop, but cant get the IP address, and give Limited Connectivity error.
How can i fix this issue.
I have tested with a client already connected, by disconnecting and reconnecting.
Its just normal on that device, I have also disconnected all, and connected my device, it fails to connect; its mentioned as disabled when we scan for the AP.
This is really every strange, that only some are connected and will be connected, but rest will never ever connect.
Do I have to reset to factory and reconfigure the device.
Thanks
Similar Messages
-
Cannot Connect a second monitor to HP 500-314PC
I have a new Pavillion 500-314. It has a VGA and DVI-D connector at rear. The comuter will not see my second monitor. I have it conneced with a dedicated line DVI-D to DVI-D. When I switch the monitors , the VGA works on both. One monitor is old and so it is connected to VGA port. The other monitor has both DVI-D and VGA, but I cannot get the DVI-D to work.
Any thought? Thanks
Model No 500-324
Serial Number [Serial Number edited by Moderator]
Windows 8
AMD Radeon R7 grpahics
AMD A8-7600 Accelerated processorHi @jaubele ,
Thank you for visiting the HP Support Forums. I needed to edit your post and remove the Serial Number. In accordane with our Rules of Participation:
Protect privacy - yours and others'. Don't share anything about yourself that you would not want to see on a road-side billboard. Don't post contact or other personal information-your own or anyone else's-or any content that you receive in one-to-one communications without the author's consent. For example, don’t post your computer’s serial # or contact information publicly, and do not allow someone you don’t know to remotely take control of your computer.
If you need people to contact you directly, either ask them to send you a private message or subscribe to the thread so you will be notified when there are replies. You may also click on your name anywhere in the forum and you will be taken to your profile page, where you can find a list of threads you have participated in.
Sharing personal email addresses, telephone numbers, and last names is not allowed for your safety. If you have any questions feel free to send me a private message in reply.
Thank you
George
I work for HP -
Application cannot connect to second page when oracle is used as database.
Hi,
I have an application which works on MySql database. But now I need to change the database to oracle. I have installed everything required inorder for the oracle to work. I am using active record store for my application. For that I have created sessions table using
rake db:sessions:create
And I have migrated to my database using
rake db:migrate.
Then I uncommented the following line in environment.rb:
config.action_controller.session_store = :active_record_store
Then If I start my application using IE, First page is shown, when I click on the second page link,
I got HTTP 500 Internal Server Error saying
The website cannot display the page
HTTP 500
Most likely causes:
The website is under maintenance.
The website has a programming error.
What you can try:
Refresh the page.
Go back to the previous page.
More information
I am unable to understand what the problem is. When I comment the line config.action_controller.session_store = :active_record_store application works, but the sessions table is not updated. when I use MySql as my database, everything works fine.
Can someone please help me with the solution? what may be the mistake am doing?Please provide more information about this issue.
Are you using oracle_enhanced adapter? (activerecord-oracle_enhanced-gem)
Which Rails version are you using?
Can you look in your log file what exception you are getting? (if running in development mode then it should be in log/development.log)
Raimonds -
CANNOT CONNECT A SECOND NANO TOSAME COMPUTER
I'm having a terrible time installing and setting up a second Nano to same computer.
First Nano was installed at Christmas (last year) and works fine; the new Nano (from Christmas this year); the software will not install and the music doesn't show up on the new Nano.
I have Windows XP and using "Windows Media Player I've tried "Syncing" the music files from my Windows Media Player library to the new Nano and I've tried "Copying/Pasting" the music files from Windows Explorer to the new Nano. When I open the Windows Explorer and click on the drive for the Nano (on my computer it's Drive-E) the music files are there, but the music files DO NOT appear on the Nano's display screen nor will the Nano play the music. I'm sure this has something to do with installing the new Nano's software and I'm at a complete loss as to what to do.
This is all so frustrating; I cannot understand why Apple makes these things so complicated; my youngest daughter is broken hearted because she cannot enjoy her Nano like her older sister. I feel totally helpless!!! CAN SOMEONE PLEASE HELP ME???
I can be contacted direct at either, "[email protected]" or "[email protected]"
Dell Windows XP
Dell-8300 Windows XPThank you KaeBFly for your feed back. I understand about syncing from Windows Media Player now. I actually tried that only as a last resort and found that it didn't work either. I first tried downloading the software for iTunes 7 and it didn't work. I'm wondering if I should first delete the software that was loaded with last year's iPod (Gen 1 model) and then download the iTunes 7, or is it possible to use the iTunes that was loaded onto the computer (with last year's Gen 1 Nano) with this year's new Gen 2 Nano.
-
I have two networks one each in two cities. Both are named the same but require different passwords. I am at my second location and cannot connect to this wifi network. How do I delet one network so I can connect to my second network?
Just go to the wireless network preferences and empty out all the stored wireless networks.. then scan and connect to the local wireless.
Select them and tap the - button below it.
Once they are emptied out.. it might be good to reboot the computer with the remember networks unchecked.
Start with a clean slate. -
hi ive been given a second hand i phone but cannot connect it to i tunes i get a itunes error (OxE8000084). also cannot unlock phone thanks
This may help:
http://support.apple.com/kb/TS3221
Regards. -
I cannot connect to an update for windows for adobe premiere elements 9 ar to change my sign-in. it gives me an error message 400 saying photo shop is unavailable. this makes the second day.
This is a user to user forum, not Adobe support
Select a topic, then click I STILL NEED HELP to start Premiere Elements Online chat
-http://helpx.adobe.com/contact.html?step=PRE -
I have iphone3gs current software ver. is 4.2.1 and it cannot update to software version 4.3. Please help me. I tried to restore the settings of my iphone but still no work. im using the current ituned 10.4. Second, I cannot connect to all wifi networks
But the model no. of my iphone i.e A1303 is of 3GS as clearly mentioned here >> http://support.apple.com/kb/HT3939. Then how its become 3G.
-
HP Wireless Printers cannot connect to WPA2-secured WiFi networks with Cisco/Meraki WAPs
In the last two months, I've had the displeasure of working with two very different HP printers and attempting to make them work on a WPA2-secured wireless network. All attempts to authenticate fail with "invalid phassphrase".
I'm not the first person to encounter this, it's a problem with many different HP wireless printers (I just happen to have physical access to the OfficeJet Pro 8610 & Deskjet 3511).
My equipment is a Cisco ASA 5505 Firewall running ASA 9.1x & Cisco Aironet 1142 running IOS 15.3.x.
What does work on the WPA2/AES SSID: Apple MacBook Air running OSX 10.10.2, Three Windows-Based laptops running Windows 8.1 Update 1, an iPhone 5s, Three Windows Phone 8.1 devices, Roku 2, PlayStation 4, PlayStation 3, Sharp Aquos TV, Amazon Streaming Stick, and an Android Tablet (Jellybean). Basically, everything.
What does not work on the WPA2 network: OfficeJet Pro 8610 & Deskjet 3511.
To test the theory there is a problem with HP's implementation of WPA2 with regard to Cisco Aironet IOS, I built out a second SSID that only works in WPA/TKIP mode. This solution works. Both HP printers will join the WPA/TKIP network.
So, I'm able to demonstrate there is a certain connectivity issue. When i look at AAA Debug on the WAP's console, I can observe the HPs attempt to authenticate "Bind I/F" on the WPA2 SSID, however they do not achieve authentication and do not pass the AAA phase. However, on the WPA SSID, they bind and authenticate successfully.
To help illustrate this, here is my WAP running config. It's about as simple as it can get. There is no relevant MAC filtering or ACLs bound to any interface. Noting that I have an ACL on remote access to the WAP (i.e. Locked down to SSH, disabling telnet). The main point being that the ASA firewall is not a factor in this problem as the issue is at the WAP before WPA2 authentication can complete, therefore the printers never reach the network / when the printers connect to the WPA network, the operate fully & correctly.
If anyone at HP can indicate why this particular config is somehow improper or broken, that would be fantastic. There should be no reason why Cisco / Meraki WAP owners have to lower wireless encryption standards just for a printer, be forced into wired, create separate SSIDs with lower encryption specifically for a device.
Building configuration...
Current configuration : 6064 bytes
! Last configuration change at 12:46:47 UTC Fri Aug 20 1993 by admin
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname 10-10-50-1
logging buffered 1024768
logging rate-limit console 9
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
no ip source-route
no ip cef
ip domain name freedom.local
dot11 syslog
dot11 vlan-name inside vlan 50
dot11 vlan-name inside-wpa-only vlan 70
dot11 ssid inside
vlan 50
band-select
authentication open
authentication key-management wpa version 2
mbssid guest-mode
wpa-psk ascii 7 xxxxxx
information-element ssidl
dot11 ssid inside-wpa-only
vlan 70
band-select
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 xxxxxx
information-element ssidl
dot11 band-select parameters
cycle-count 3
cycle-threshold 200
expire-supression 20
expire-dual-band 60
client-rssi 75
dot11 wpa handshake timeout 500
dot11 network-map
username ADMIN privilege 15 secret 5 xxxxxx
ip ssh version 2
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 50 mode ciphers aes-ccm
encryption vlan 70 mode ciphers aes-ccm tkip
ssid inside
ssid inside-wpa-only
antenna gain 0
mbssid
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel 2412
station-role root
l2-filter bridge-group-acl
interface Dot11Radio0.50
encapsulation dot1Q 50 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 input-address-list 700
bridge-group 70 output-address-list 700
bridge-group 70 spanning-disabled
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.50
encapsulation dot1Q 50 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 spanning-disabled
no bridge-group 70 source-learning
interface BVI1
mac-address xxxx.xxxx.xxxx
ip address 10.10.50.1 255.255.255.0
no ip route-cache
ip forward-protocol nd
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip route 0.0.0.0 0.0.0.0 10.10.50.2
logging history size 100
access-list 111 permit tcp any any neq telnet
bridge 1 route ip
line con 0
access-class 111 in
line vty 0 4
access-class 111 in
length 0
transport input ssh
line vty 5 15
access-class 111 in
transport input ssh
endI get the same behavior with a laserjet m451nw. I need to enable tkip to get the printer working, it doesn't support pure aes-ccm (every other device here supports pure aes-ccm, even cheap ones), although it's advertised as working.
The following snippet of config works, but I still think it should work without the tkip "hack".
dot11 ssid whatever
vlan 1
band-select
authentication open
authentication key-management wpa version 2
interface Dot11Radio0
encryption vlan 1 mode ciphers aes-ccm tkip -
i am trying to connect to my friend's wifi, i have a very strong signal indicated on my ipad, but cannot connect to the internet. Yesterday i connected without any problem, can anybody tell me why i cannot connect today?
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
HP LaserJet 200 color MFP M276nw - cannot connect
Hello,
Installed a HP LaserJet 200 color MFP M276nw on a Windows 7 system with no issues. Then added the "device" / printer on two Windows tablets, with no issues. I was able to print from all three devices. The tablets cannot 'find' the printer.
I then added the printer to another Windows 7 system and now cannot connect from the other systems. I am still able to print from the second Windows 7 system. (I removed the printer from the second Windows 7 system and readded it without issue, and ensured Share the Printer was selected).
Please advise. Should I just return the printer?Wireless Network Configuration
Status: Connected Wireless: On
Network Name (SSID): xxxxxxxxx
Communication Mode: Infrastructure Authentication
Type: wpa2-psk
Encryption: tkip+aes
Hardware Address: xxxxxx Access Point Hardware Address: xxxxxx
Channel: 6
Signal Strength: Very Good
***Marked out some of the settings*** -
Cannot connect to TC, even after factory reset
I bought a 1TB TC from apple in 08/2008. I don't recall if it was a refurb or not. It worked fine for 4.5 years with more or less no problems. About a month or two ago the Wi-Fi stopped working. I could connect to the SSID, but occasionally could not get an internet connection without cycling the power of the modem and TC. Finally, the cycling trick stopped working, and while I could connect to the TC I couldn't get internet. I switched to the WiFi capabilties that my Comcast modem had (as I didn't have time to address the issue then). I've finally gotten around to trying to fix it and could not find the TC via WiFi. I attempted a hard reset, but holding the reset button (while under power) did not make the yellow light flash, even after 30 seconds. I then performed a factory reset by holding the reset button while plugging in the TC. The light flashed, indicating the factory reset occurred.
After the factory reset I still cannot:
-Find the TC via WiFi
I attempted using both my previous SSID and searching for the default "Apple Network XXXXXX" signal. No dice.
-Find the TC via Ethernet
I attempted to connect my MBP directly to the ethernet port (<--->) on the TC but the red light remains on the Ethernet in Network Settings (Status: Cable Unplugged. Either the cable for Ethernet is not plugged in or the device at the other end is not responding). I verified the cable works by connecting the ethernet cable to the cable modem and instantly getting the green "connected" light and an internet connection.
-Find the TC via Airport Utility
The TC did not appear, even when plugged in directly with the ethernet cable.
I'm not sure if this is a firmware issue or what. The lights turn on the front and in the LEDs above the ethernet jacks in the back during power/start up but is otherwise unresponsive. I cannot attempt a firmware update as I cannot connect to the TC by WiFi/Ethernet, let alone through the Airport utilitiy.
I'm not sure if this is relevant or helpful but the TC is also making a ticking/hissing slightly faster than once a second as if the drive is being accessed.
Can anyone help!?! I have quite a drive to an apple store and I'm sure what they would charge to mail in and fix it would be excessive.
Many karma points await anyone that can help!!! Thanks in advance for your time!The power supply is dead.
Solid amber could also be a dead hard disk.
Apple will not fix it and do not supply parts for anyone else to fix them.
It is really no longer economic to repair unless you can DIY. And even then if the hard disk is gone then it really is a waste.. just buy a replacement.
See https://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modem s/apple-time-capsule-repair
I have given several methods.. some rough but very cheap to repair the TC.
Otherwise it is just time to buy a new one.. or IMHO a Gen4 is an excellent buy.. second hand or from your local apple refurbish store. -
Hi. I am having problems connecting to the wifi at my caravan site. My iPad recognises the connection but when I put the password in correctly it says it cannot connect. I have reset my network settings in general but it has made no difference . Any ideas?
Some may not be applicable.
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
I cannot connect to the internet after switching providers. I've changed the email address associated with the new account but am sure there is something else I need to change. I have also changed the apple information as well including user name and password. Can anyone help me? (This is an ipad question).
Apple ID: Changing your Apple ID
http://support.apple.com/kb/ht5621
Using your Apple ID for Apple services
http://support.apple.com/kb/HT4895
Apple ID: What to do after you change your Apple ID
http://support.apple.com/kb/HT5796?viewlocale=en_US&locale=en_US
iTunes Store: Associating a device or computer to your Apple ID
http://support.apple.com/kb/ht4627
iOS: Changing the signed-in iTunes Store Apple ID Account
http://support.apple.com/kb/ht1311
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at
http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are drooping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
iPad: Issues connecting to Wi-Fi networks
http://support.apple.com/kb/ts3304
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.hmL
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Signal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
10 Ways to Boost Your Wireless Signal
http://www.pcmag.com/article2/0,2817,2372811,00.asp
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
I have one Cisco Aironet 1231 access point. It does not use any kind of (server) functionality outside the Cisco device.
I have one SSID and uses WPA-PSK (TKIP).
The configuration seams wary straight forward, but something is wrong.
The access point seams to be unstable. The clients use long time to connect to the access point and it looses connection a lot of times a day. Can I do something to speed up the ?negotiation process? ?
What could be the course of instability?
The configuration was made with the ?web configurator?, but I have a SSH/telnet dump:
Best Regards
Martin
AP1#sh run
Building configuration...
Current configuration : 2227 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP1
enable secret xxx
clock timezone GMT 1
ip subnet-zero
ip domain name mydom.com
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
dot11 ssid myssid
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii xxx
username Cisco password xxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid myssid
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2412
station-role root
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no cdp enable
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
hold-queue 160 in
interface BVI1
ip address 192.168.1.105 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
access-list 111 permit tcp any any neq telnet
no cdp run
radius-server local
no authentication leap
no authentication mac
radius-server attribute 32 include-in-access-req format %h
radius-server vsa send accounting
control-plane
bridge 1 route ip
line con 0
access-class 111 in
line vty 0 4
access-class 111 in
sntp server 212.242.xx.207
sntp broadcast client
end
AP1#A "stronger" (more gain) antenna probably won't help. An antenna that transmits with more gain also receives with more gain ..(basically, the same situation, but all of the signals are "louder")
The general remedy, aside from the obvious of going to the least populated channel or moving to the 802.11a band, is usually to add more access points, all using some flavor of "sector" antenna (and / or "patch" antennas) to localize the area of interest.
Because the antennas are covering a more specific area (and usually smaller area), it is usually the case that more APs are needed.
"Seeing" 20 APs is not that alarming ... check the signal strength of each, many will usually be well-below the level that would cause serious interference. The specific level will vary, depending on the location relative to the AP<->client relationship.
If you're seeing 20 APs, and their signal strength is roughly the same as your APs or a little lower, then you've got a problem that only a sectorized antenna system can cure.
Good Luck
Scott
Maybe you are looking for
-
My iPad keeps telling me that I am up to date with iOS 5.1.1. What do I need to do to download and install iOS 6?
-
Problem with Input out put parametes of IViews in callable objects
Dear Friends, I have designed model which contains 2 IViews Apply leave IViews Approve leave Iviews In both the cases i have exposed the in & out parameters using start & end point. Finally deployed in portal successfully Guided procedures ->Design T
-
Achieving accurate colour prints
Hi, I am using Ps CS5.1, Canon printer Pixma MP988 & a Mac OS X10.9.1. In the last couple of weeks I no longer am getting correct pri ntouts, I susspect something related to colour profiling has recently changed (I must have done it myself but not aw
-
Best APEX developing practices?
Hello, I have a simple question - What are the best APEX developing practices in regards to developing workspaces ? There are two ways to develop in APEX (when you create an application for internal use, of cause) : One is to have a workspace per App
-
i photo freezes up soon after start up. As soon as you try to do anything the spinning icon appears and then the only thing to do is a forced quit. can anyone help me with this?