Cannot connect to the Internet with my Satellite 1800-712

Hi,
had to reinstall WXP on my Satellite 1800-712, unfortunately have not the recovery disk otherwise it would all be ok.
Now I cannot get onto internet, I have downloaded new LAN drivers, installed them ok, LAN is set for auto detect, USB wireless dongle drivers installed all ok.
In my tray (bottom right) icon shows networks but with red cross... I get a message saying wireless networks are within range, click to see networks... when I click , sunscreen comes up saying no networks in range..... aarrrgggh.
What can I do, please?

Hello
Have you checked if the WLAN card is enabled on your notebook?
The hardware switch on the notebook must be set to on and you can also enable it with FN+F8.
Check this!!
Furthermore check the device manager for yellow exclamation marks. Maybe you should reinstall the driver. Therefore select the WLAN card in device manager and choose uninstall. Restart the notebook and install the newest WLAN driver from the Toshiba website.
Last but not least make sure that the router is in range of the notebook.
Good luck!

Similar Messages

WRT 120N- Cannot connect to the internet with more than one PC at a time.

Before I went on a three month vacation,I could connect 3 or 4 PC's either wireless or wired to my router with no problems at all.I have a desk top and a laptop computer which I use at home.After I returned,I found that I could connect to the internet with only one PC at a time.
If I was say,connected via my laptop,my desk top would continuously keep getting disconnected and vice versa.I have been reading the suggestions from experts here and have done a few checks based on them.I also cannot get to my router page which is 192.168.1.1 I keep getting a message that says "Problem Loading Page" and this happens with both,Firefox and Internet Explorer.I am running Windows 7 - 32 bit on my desk top and Vista Home Premium on my laptop.
I have opened the "Command Prompt" dialogue and pinged 192.168.1.1 and thereafter I typed in "ipconfig".These are the results:
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:\Users\Gordon>ping 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
Ping statistics for 192.168.1.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 0ms, Maximum = 0ms, Average = 0ms
C:\Users\Gordon>ipconfig
Windows IP Configuration
PPP adapter Brownwolf:
   Connection-specific DNS Suffix . :
   IPv4 Address. . . . . . . . . . . : 92.98.42.65
   Subnet Mask . . . . . . . . . . . : 255.255.255.255
   Default Gateway . . . . . . . . . : 0.0.0.0
Ethernet adapter Local Area Connection* 22:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
Wireless LAN adapter Wireless Network Connection:
   Connection-specific DNS Suffix . :
   IPv6 Address. . . . . . . . . . . : 2002:5c62:2a41:c:35a2:8753:8832:f494
   Site-local IPv6 Address . . . . . : fec0::c:35a2:8753:8832:f494%2
   IPv6 Address. . . . . . . . . . . : 2002:5661:4cc9:c:35a2:8753:8832:f494
   Temporary IPv6 Address. . . . . . : 2002:5661:4cc9:c:a408:59a3:918e:f0ab
   Temporary IPv6 Address. . . . . . : 2002:5c62:2a41:c:a408:59a3:918e:f0ab
   Link-local IPv6 Address . . . . . : fe80::35a2:8753:8832:f494%12
   IPv4 Address. . . . . . . . . . . : 192.168.0.1
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Default Gateway . . . . . . . . . :
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . :
   IPv6 Address. . . . . . . . . . . : 2002:5c62:2a41:c:413:cf4f:77af:474d
   Site-local IPv6 Address . . . . . : fec0::c:413:cf4f:77af:474d%1
   IPv6 Address. . . . . . . . . . . : 2002:5661:4cc9:c:413:cf4f:77af:474d
   Temporary IPv6 Address. . . . . . : 2002:5661:4cc9:c:1591:ad9:13da:8fea
   Temporary IPv6 Address. . . . . . : 2002:5c62:2a41:c:1591:ad9:13da:8fea
   Link-local IPv6 Address . . . . . : fe80::413:cf4f:77af:474d%11
   IPv4 Address. . . . . . . . . . . : 192.168.1.100
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Default Gateway . . . . . . . . . : fe80::35a2:8753:8832:f494%11
                                       192.168.1.1
Tunnel adapter Local Area Connection* 7:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 11:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 14:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 15:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 19:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 20:
   Connection-specific DNS Suffix . :
   IPv6 Address. . . . . . . . . . . : 2002:5c62:2a41::5c62:2a41
   Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301
Tunnel adapter Local Area Connection* 23:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 24:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 28:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
I presume that this model is a modem **bleep** router as I do not have a separate modem with my system.I have a DSL connection and the firmware version of my router is ver.1.0.If I recall,I did upgrade to the next firmware upgrade a few months after I purchased the router but I am not sure.
I use both my PC's to run a small business venture and I am worried that resetting the router may cause some other problems and will stop me from using the internet.
The Command Prompt information above was taken from my laptop.
Any help will be really appreciated.
Gerard.
Solved!
Go to Solution.

brownwolf66 wrote:
No,I have a desk top and a laptop and I cannot access 192.168.1.1 on either of them.In my OP,I have used the Command Prompt dialogue on both computers to ping 192.168.1.1 and I have attached the results.This is what I got:
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:\Users\Gordon>ping 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
Reply from 192.168.1.1: bytes=32 time<1ms TTL=111
Ping statistics for 192.168.1.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 0ms, Maximum = 0ms, Average = 0ms
The results I obtained using ipconfig in the command prompt have already been mentioned in my OP.
I do not know if the above result is what it is supposed to be but I still cannot access my router's home page.How do I verify if there is a proxy server and if there is one,how do I disable it in my browsers?This problem occured suddenly as a few months earlier all was well.It's getting rather frustrating.
I suggest resetting the router. Make sure firmware is updated. You can download it here - http://homesupport.cisco.com/en-us/support/routers/WRT120N. After firmware upgrade, reset and reconfigure. Just access the link below to guide you setting up the router.
* Setting up a Linksys router for DSL Internet connection
http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20ee1457387f40178cd5f41d4b585db4_3687.xml&pid=80&r...
* Setting up a Linksys router with Cable Internet service
http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0ff4c94586a345d082828ec2161aaecf_3686.xml&pid=80&r...

I downloaded version 4 and now I cannot connect to the internet with firefox. The lower version worked fine. It keeps saying I'm offline. Any suggestions?

I have used the older version of firefox and it worked fine. I downloaded version 4 and now cannot get on the internet with firefox. It keeps saying I'm offline and to check a particular box to correct the problem. I have no idea what they're talking about and would appreciate any help.

Ah I figured it out.....Mcafey was blocking it. Why on earth did AVG being uninstalled update mcafey settings, to block firefox?

Cannot connect to the Internet with browser when using VPN

I am experiencing an odd network problem and am hoping that someone on this list has seen something similar and can help me isolate the cause.
I have a Mac Pro running Mac OS X (10.5.8) and use Cisco's VPNClient to connect to my employer's network. Some time in the last year I started getting this odd behavior wherein that while connected via VPN, I cannot open external web pages in Safari (Version 5.0 (5533.16)). When this happens I get the following message:
+Safari can't open the page "http://www.google.com/" because your computer isn't connected to the Internet.+
Web pages on the company's internal network work fine. Firefox exhibits the same problem. However, the very odd thing (to me), is that I can get to the Internet using the browser in NetNewsWire. Other services (like twitter) also seem to work fine.
The problem is intermittent and occurs between restarts. After some restarts the problem is not there. Also, connecting and re-connecting via VPNClient does not affect the behavior. If access to the Internet is working then it will continue working, at least until the next restart. If I restart for whatever reason (software update, etc.) the next time it may or may not work.
This has been going on over several updates to Mac OS X and Safari.
Another clue is that my MacBook, also running 10.5.8 works fine when connected from the same home network so I am pretty sure the problem is with my Mac Pro.
Anyone out there have any idea what could be causing this and how to go about fixing the problem?
Thanks in advance,
KP

Earthlink can be challenging. Have a look at this
very helpful post from Eme.
This may lead you in the right direction.
World leaks relates to memory issues with Safari that
are on-going and being addressed in the developer's
community. More information can be found
here.. To
stop the warning message, go to your Debug menu and
deselect "always check for world leaks".
iMac G5 Rev C 20" 2.5gb RAM 250 gb
HD/iBook G4 1.33 ghz 1.5gb RAM 40 gb HD Mac
OS X (10.4.8) LaCie 160gb d2 HD Canon i960
printer
I couldn't fix it, and the Earthlink technician couldn't fix it...until she checked and found that the starting address: "www.my.earthlink.net" is down. In fact, it's still down, so I'll just continue using Foxfire for awhile. I can connect by typing "www.earthlink.net" in the addres bar, but it's so much easier to just click on Foxfire in my dock. This shows the value of having a spare browser.
I'm going to mark it "solved. Thanks for your help, It was a bit technical for me, but I tried. I had to, having just sent an article about the value of persistence to a friend, how could I fail to persevere?

Cannot connect to the internet with laptop

Background: Started out with iMac connected to Apple Airport Extreme base station via wireless that is connected to broadband/cable linksys modem befcmu10. Then setup Apple Macbook 13" to access internet through Apple Airport Extreme base station via wireless. Worked fine, spectacular. Then setup HP Photosmart C6180 All-in-One printer to be accessed through Apple Airport Extreme base station. Again, worked flawlessly. Then setup and "installed" an offline internet Skype phone [Philips VOIP8411B/37] so I could use it's services and not need a computer to be on. It's connected to the Apple Airport Extreme via Ethernet. To get it up and running, I had to reboot my modem and router. Right after I got it up and running I noticed that the Skype phone was working and the iMac was working but the laptop was now not able to connect to the internet.
Present: Finally able to get back to finding a solution, I was trying to look at settings in the network system preferences and researching things to try. Also going to the Airport Utility program trying different things like having it distribute IP address and having it find DNS servers automatically, etc etc etc. Nothing was working to get the Macbook back online. So I rebooted the modem and router again [because i have been experiencing problems with cable company] just for the heck of it. Wa-la, the iMac and laptop were now both using the internet. But before I realized what was happening, the Skype phone was not able to establish a connection. So before I stopped for the night, I shut everything down and rebooted the cable modem and router.
Next morning I awoke and the Skype was working but the iMac and Macbook weren't able to connect. After trying to fiddle with System Preferences and Airport Utility I resorted to reboot the modem and router. iMac worked, Macbook didn't, Skype worked. After a full day of researching, reading and fiddling with preferences on the macs end, I decided to try the reboot of modem and router. Got iMac online, Macbook online, Skype not.
Discovered problem: Apparently only two of the three devices can connect to the "internet" through the Aiport Extreme base station at a time. So right now, I have to sacrifice one device not to connect to the internet. It's the Macbook for now. From what i can see, the use of the printer is not affected [but it's only setup on the iMac].
I've gone into the network diagnostics on the Macbook and under Network Status on the left, Airport, Airport Settings, Network Settings, and ISP are all green, while Internet and Server are yellow for a second while it searches but turn red and stay red. Contacted cable company and everything is good on their end and they couldn't help further. Something is wrong on my end. Now on to apple care or forum help.
Does anyone have a solution or suggestion of what to do or where to look? Do I have to change something in the Apple Airport Extreme base station? Network setting? Any help would be much appreciated, it's frustrating and time consuming and I'd like to get it all up and running.
Thank you for your time.
BCSlck1

I don't have an answer, but I experienced the same problems trying to set up an airport express to route traffic to my stereo.
Apple Extreme router, iMac and laptop all worked just fine for months, upon installing Airport Express (step by step, according to instructions), all **** broke loose. Airport Utility was unable to see my Airport Extreme router, after hours of rebooting computer, cable modem, router, and finally a hard reset of the Airport Extreme router, it is finally recognized by Airport Utility again.
Recreated network, iMac connects to the internet just fine, laptop (Macbook Air) connects to the network just fine, but will not connect to the internet. Network diagnostics does not help, it gets to the "do you have a router? If so, reboot" stage, and never seems to see the router.
Any suggestions?

I have AirPort Extreme and cannot connect to the internet with a land line but the WiFi works

I have an AirPort Extreme and have been using for several months successfully, but as of two weeks ago, the line that I have hooked up to my desktop no longer provides internet service, but the WiFi works fine for the I-Pad and I-Pod.
I have checked with my service provider and my modem works successfully hooked up the the AirPort extreme or directly to the PC. When I am hooked in from the modem directly to my PC, I have internet for my desktop, but of course no WiFi.
If I connect the Modem to the Router and the router to my desktop, I have WiFi, but no internet service to my desktop.
I have replaced the network cable but to no avail.
Any suggestions?

It appears that there may be something amiss with the Ethernet switch that is built-in the 802.11n AirPort Extreme Base Station (AEBSn) or its configuration settings may be incorrect. I assume that you also tried using the other LAN ports on the AEBSn and the outcome was the same ... no Internet access via a wired connection.
One thing to try is to change the Ethernet adapter settings on the PC. It is possible that its current settings may be appropriate when connected directly to the Internet modem, but may be off for connecting to the AEBSn. If your PC's Ethernet adapter has options to control Speed, Duplex, & MTU, I would change these to the following respectively: 1000 Mbps, Full duplex, & 1500

Cannot connect to the Internet with my Sun Ultra 20 Workstation

Hi Everyone,
I am very new to Solaris world. I have an Ultra 20M running Solaris 10 (x86), and a Linksys 350N router connected to a cable modem. But I am not able to go online. Please can you help me with the commands or steps I need to take for configuring the Solaris for accessing the Internet ?.
Any help, is much appreciated!
Thank you,

Are you using the router to do any verification the cable company needs? I assume so and if you are not I would set it up so it does (if it is even needed with cable internet).
After that it should be simply a matter of turning on DHCP. The easiest way is to type sys-unconfig as root. That will 'reset' all of the important network settings. Choose dhcp. The default router address is probably something like 192.168.0.1 or 1.1
I believe that will be both your gateway and dns.
This all assumes you are using the router as a router and not a switch.
You can then use the router as a firewall and dmz your ultra if you feel like connecting to it from the outside (if you have a static ip for your router).
Same goes with windows, linux, BSD, Apple etc... nothing solaris specific but the sys-unconfig bit.

TA48312 I'm using iTunes 11 final version on my pc windows 7 and I cannot connect to the internet with any of its feautures. why? I'll be grateful if you help,thanks in advance.

Hi everybody,
First of all I was not one of iTues users till by chance discovered its amazing features of downloading all kinds of items that help in education in particular. I set up iTunes version 8 I gusse and it was working properly either by using direct connect to the material or downloading it. Then, I made I mistake when I tried version 11 and everything stopped working. No downloading or even connecting the web. I'm a student and I'm in a bad need to this wonderful programme. I must not forget that I tried many steps to solve this problem by uninstalling iTunes with its contents from its roots till registry files, and I set up the old version once and then the newer version 11 and finally version 9 and all my trials were in vain. Please I need your help and advise. I'm looking forward for your reply and thanks in advance for your care.
adam karim,

Many thanks.
With those symptoms, I'd try the following document:
Apple software on Windows: May see performance issues and blank iTunes Store
(If there's a SpeedBit LSP showing up in Autoruns, it's usually best to just uninstall your SpeedBit Video Accelerator.)

Cannot connect to the internet with firefox

Firefox opens (sort of) to my Yahoo home page, but shows only my Bookmarks sidebar, and the top toolbars, plus a blank page and a tab labeled "Untitled"
== This happened ==
Every time Firefox opened
== About 9:00AM today. Was fine from 6:30 to 8:00AM. ==
== User Agent ==
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; WOW64; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; HPDTDF; .NET4.0C)

Ah I figured it out.....Mcafey was blocking it. Why on earth did AVG being uninstalled update mcafey settings, to block firefox?

TS2756 iam using iphone 4S with win 7 PC and i cannot connect to the internet through my phone but i tried with my other 4S and it works but what should i do for the first iphone 4S???

iam using iphone 4S with win 7 PC and i cannot connect to the internet through my phone but i tried with my other 4S and it works but what should i do for the first iphone 4S???
as i said i have two iphone 4S,,,,,
1st one --- has os 5.1
2nd one has os 6.0
i tried 2nd one with carrier reliance gsm nd it works with that personal hotspot setting using USB...
but i want to connect the first 4S with carrier TATA DOCOMO GSM but its not working with the same USB feature????
plz reply asap...!!!
thnxxx in advance!!!

If not this:
iOS: Wi-Fi or Bluetooth settings grayed out or dim
One user reported that placing the iPod in the freezer fixed the problem.
Also heating sometimes works. See:
Why can't I select my wifi settings?
A trick that works frequently with iPhones:
Settings > AirPlane Mode ON, Do Not Disturb ON
Power down and wait 5-10 minutes
Power up
Settings > AirPlane Mode OFF, Do Not Disturb OFF
If not successful, an appointment at the Genius Bar of an Apple store is usually in order.
Apple Retail Store - Genius Bar
Then:
Does the iOS device connect to other networks? See other networks? If yes that tends to indicate a problem with your network.
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

HT4623 I keep getting an error message "cannot connect to the internet." Is this a problem with my internet provider, or has anyone else had this problem.

I keep getting an error message "cannot connect to the internet." Is this a problem with my internet provider, or has anyone else had this problem.

I get that problem once in a while and I will not be able to connect to the Internet with any of the 5 or 6 (or 7 or 8 ) web browsers that I use on my iPad. The one thing that I do that has never failed to work for me is to close all apps on my iPad and reset the device. I can't guarantee that it will work for you, but this works for me every time I get the server failed to load/can't connect to the Internet message.... Or whatever the exact message is.
If you have a ton of apps in the multitasking display, it can take a while to close them all, so you could just trey resetting the iPad first and that might be all that you need to do.
Closing apps in iOS 7 works like this. Drag the app up from the multitasking display. Double tap the home button and you will see apps lined up going left to right across the screen. Swipe to get to the app that you want to close and then swipe "up" on the app preview thumbnail to close it.
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

I cannot connect to the internet after switching providers. I've changed the email address associated with the new account but am sure there is something else I need to change. Can anyone help me?

I cannot connect to the internet after switching providers. I've changed the email address associated with the new account but am sure there is something else I need to change.   I have also changed the apple information as well including user name and password. Can anyone help me? (This is an ipad question).

Apple ID: Changing your Apple ID
http://support.apple.com/kb/ht5621
Using your Apple ID for Apple services
http://support.apple.com/kb/HT4895
Apple ID: What to do after you change your Apple ID
http://support.apple.com/kb/HT5796?viewlocale=en_US&locale=en_US
iTunes Store: Associating a device or computer to your Apple ID
http://support.apple.com/kb/ht4627
iOS: Changing the signed-in iTunes Store Apple ID Account
http://support.apple.com/kb/ht1311
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at
http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are drooping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
iPad: Issues connecting to Wi-Fi networks
http://support.apple.com/kb/ts3304
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.hmL
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Signal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
10 Ways to Boost Your Wireless Signal
http://www.pcmag.com/article2/0,2817,2372811,00.asp
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

My PC can connect to the airport extreme but with encryption it cannot connect to the internet my iMac has no issues, any help.

My PC can connect to the new airport extreme I just purchased but with encryption it cannot connect to the internet my iMac has no issues. If I open the airport exteme up and provide no security everything is fine which leads me to believe it is something with the encryption between the two devices. Not sure what step I'm missing here this shouldn't be this difficult.

Sorry, I should have been more clear. I am asking if the DNS IP addresses, not the IP addresses assigned by the DHCP service, are the same. DNS is like the Internet's version of the Yellow Pages. Your ISP typically will provide them to you or you can elect to use those provided by another source, like OpenDNS.
DNS is the service that translates a website's URL to its actual IP address so that you can access it. I am just trying to rule out that the PC is not configured properly with the correct DNS IP information.
The other thing to check is if the PC is configured to use a Proxy service. By default, it would not be.
Finally, what is the make & model of the PC. More importantly, if the PC is using either a PCI or USB wireless adapter, what is its make & model?

Firefox cannot connect to the internet...i can get on with int. explorer

I always use Firefox as my browser...may be 4.0...recently, I get a message that firefox cannot connect to the internet. I do have an internet connection, since I can connect with internet explorer...any suggestions?

For possible causes see [[Firefox cannot load websites but other programs can]].

My Macbook Pro cannot connect to the internet using an ethernet cord.

My Macbook Pro cannot connect to the internet using an ethernet cord. It was working fine for weeks, then all of a sudden just stopped. What could the problem be?

Hi bean07670,
If you are having an issue with the Ethernet connection on your MacBook Pro, you may find the following article helpful:
Mac OS X: Troubleshooting a cable modem, DSL, or LAN Internet connection
http://support.apple.com/kb/TS1317
Regards,
- Brenden

Cannot connect to the Internet with my Satellite 1800-712

Similar Messages

Maybe you are looking for